Methanol synthesis on Cu(100) from a binary gas mixture of CO2 and H2

The rate of methanol synthesis over a Cu(100) single crystal from a 1 1 mixture of CO₂ and H₂ has been measured at a total pressure of 2 bar and a temperature range of 483–563 K. At these conditions the apparent activation energy is determined to be 69 kJ mol^–1, and at 543 K the turnover rate is 2.7 × 10^–4 (site s)^–1. A kinetic model for the methanol synthesis is presented. Predictions from this model are in good agreement with the rates of methanol synthesis observed on real catalysts at industrial conditions.     

Methanol Synthesis on Potassium-Modified Cu(100) from CO + H2 and CO + CO2 + H2

Methanol cannot be produced from CO + H₂ on a clean copper surface, but a promotional effect of potassium on methanol synthesis from mixtures of CO + H₂ and CO + CO₂ + H₂ at a total pressure of 1.5 bar on a Cu(100) surface is shown in this work. The experiments are performed in a UHV chamber connected with a high-pressure cell (HPC). The methanol produced is measured with a gas chromatograph and the surface is characterized with surface science techniques. The results show that potassium is a promoter for the methanol synthesis from CO + H₂, and that the influence of CO₂ is negligible. Investigation of the post-reaction surface with TPD indicates that potassium carbonate is present and plays an important role. The activation energy is determined as 42 ± 3 kJ/mol for methanol synthesis on K/Cu(100) from CO + H₂.     

The difference in the active sites for CO2 and CO hydrogenations on Cu/ZnO-based methanol synthesis catalysts

The effect of Zn in copper catalysts on the activities for both CO₂ and CO hydrogenations has been examined using a physical mixture of Cu/SiO₂+ZnO/SiO₂ and a Zn-containing Cu/SiO₂ catalyst or (Zn)Cu/SiO₂. Reduction of the physical mixture with H₂ at 573–723 K results in an increase in the yield of methanol produced by the CO₂ hydrogenation, while no such a promotion was observed for the CO hydrogenation, indicating that the active site is different for the CO₂ and CO hydrogenations. However, the methanol yield by CO hydrogenation is significantly increased by the oxidation treatment of the (Zn)Cu/SiO₂ catalyst. Thus it is concluded that the Cu–Zn site is active for the CO₂ hydrogenation as previously reported, while the Cu–O–Zn site is active for the CO hydrogenation.     

Effects of catalyst composition on methanol synthesis from CO2/H2

Effects of catalyst composition have been studied for Cu/support and Cu/ZnO/supports in methanol synthesis from CO₂/H₂. A strong effect of support has been observed. Different supports brought about different behavior in temperature-programmed reduction of copper, different copper surface areas, and different catalytic activity and selectivity. It seemed possible to find catalyst supports that might perform better than commercial Cu/ZnO/Al₂O₃ catalysts. A correlation was observed between catalytic activity and the copper surface area which was varied by using different supports. However, the sup]>orts appeared to influence other catalytic properties as well, for example, the surface oxygen coverage.     

Methanol synthesis by the hydrogenation of CO2 over Zn-deposited Cu(111) and Cu(110) surfaces

The hydrogenation of CO₂ over Zn-deposited Cu(111) and Cu(110) surfaces was performed at 523 K and 18 atm using a high pressure flow reactor combined with XPS apparatus. It was shown that the ZnO _x species formed on Cu(111) during reaction directly promoted the methanol synthesis. However, no such promotional effect of the Zn was observed for methanol formation on Cu(110). Thus, Zn on Cu(111) acts as a promoter, while Zn on Cu(110) acts as a poison. The activation energy and the turnover frequency are in fairly good agreement with those obtained for Cu/ZnO powder catalysts.     

Oxygen induced direct hydrogenation of CO on Ni(100) surface

A trace amount of oxygen in H₂ promotes a new type of direct hydrogenation reaction of adsorbed CO on Ni(100) surface. The formation of H_xCO_y was suggested by high resolution electron energy loss spectroscopy (HREELS) and thermal desorption spectroscopy (TDS). HREEL spectra showed the formation of surface hydroxyl (OH) and the C-H bonds of H_iCO_y species but no carbonyl (C=O) loss peak was detected although thermal desorption yielded large amount of CO. The H _x CO _y undergoes the decomposition at 400–450 K on the hex-OH Ni(100) surface, which yielded CO, CO₂, H₂ and H₂CO. It was confirmed that no C-H bond formation occurs on c(2 × 2)-O, p(2 × 2)-O Ni(100) and hex-OH Ni(100) as well as on clean Ni(100) surfaces. This fact indicates that the gas phase oxygen may induce the direct hydrogenation of CO to form H _x CO _y , which is analogous to the hydrogenation of O to form hex-OH onNi(100).     

The effect of ageing time on co-precipitated Cu/ZnO/ZrO2 catalysts used in methanol synthesis from CO2 and H2

The effect of suspension ageing time during the catalyst precipitation process on the performance of co-precipitated Cu/ZnO/ZrO₂ catalysts in methanol synthesis from CO₂ and H₂ has been studied. The ageing time influenced greatly the physical and chemical characteristics of the catalysts as well as their activity in the methanol synthesis. Prolonged ageing was advantageous, mainly due to both lower sodium contents and enhanced crystallinity of the catalysts.     

The active site for methanol synthesis on a Cu/ZnO/SiO2 catalyst

This note rectifies serious omissions from the references included in a recent paper by Fujitani et al. concerned with methanol synthesis over Cu/SiO₂ containing ZnO. This revised version was published online in July 2006 with corrections to the Cover Date.     

An EXAFS study of Cu/ZnO and Cu/ZnO-Al2O3 methanol synthesis catalysts

Cu K-absorption edge and EXAFS measurements on binary Cu/ZnO and ternary Cu/ ZnO-Al₂O₃ catalysts of varying compositions on reduction with hydrogen at 523 K, show the presence of Cu microclusters and a species of Cu¹⁺ dissolved in ZnO apart from metallic Cu and Cu₂O. The proportions of different phases critically depend on the heating rate especially for catalysts of higher Cu content. Accordingly, hydrogen reduction with a heating rate of 10 K/min predominantly yields the metal species (>50%), while a slower heating rate of 0.8 K/min enhances the proportion of the Cu¹⁺ species ( 60%). Reduced Cu/ZnO-Al₂O₃ catalysts show the presence of metallic Cu (upto 20%) mostly in the form of microclusters and Cu¹⁺ in ZnO as the major phase ( 60%). The addition of alumina to the Cu/ZnO catalyst seems to favour the formation of Cu¹⁺/ZnO species.     

Isoprene formation from CO and H2 over CeO2 catalysts

The CO-H₂ reaction over CeO₂ catalysts at around 623 K and 67 kPa forms isoprene with about 20% and 70% selectivities in total and C₅ hydrocarbons, respectively. The formation of dienes may be due to the low and high activity of CeO₂ for alkene and CO hydrogenation, respectively.     

Creation of the active site for methanol synthesis on a Cu/SiO2 catalyst

The effect of ZnO/SiO₂ in a physical mixture of Cu/SiO₂ and ZnO/SiO₂ on methanol synthesis from CO₂ and H₂ was studied to clarify the role of ZnO in Cu/ZnO-based catalysts. An active Cu/SiO₂ was prepared by the following procedure: the Cu/SiO₂ and ZnO/SiO₂ catalysts with a different SiO₂ particle size were mixed and reduced with H₂ at 523-723 K, and the Cu/SiO₂ was then separated from the mixture using a sieve. The methanol synthesis activity of the Cu/SiO₂ catalyst increased with the reduction temperature and was in fairly good agreement with that previously obtained for the physical mixture of Cu/SiO₂ and ZnO/SiO₂. These results indicated that the active site for methanol synthesis was created on the Cu/SiO₂ upon reduction of the physical mixture with H₂. It was also found that ZnO itself had no promotional effect on the methanol synthesis activity except for the role of ZnO to create the active site. The active site created on the Cu/SiO₂ catalyst was found not to promote the formation of formate from CO₂ and H₂ on the Cu surface based on in situ FT-IR measurements. A special formate species unstable at 523 K with an OCO asymmetric peak at ~1585 cm^-1 was considered to be adsorbed on the active site. This revised version was published online in July 2006 with corrections to the Cover Date.     

Theoretical investigation of ethylene adsorbed on Ni(100) surface by the multiple-scattering cluster method

In this paper the carbon K-edge near edge X-ray absorption fine structure spectra (NEXAFS) of adsorption system C₂H₄/Ni(100) are calculated using the multiple-scattering cluster method. By a comparison between the theoretical results and experimental spectra, the chemisorption geometry of this system has been determined. The result shows that the molecule is adsorbed on the perpendicular bridge site, and the distance between the C atom and the nearest Ni atom is 1.70 Å, while the molecular plane tilting to the surface is 50°. It is found that the interaction between hydrogen atom and Ni substrate plays an important role in the formation of the adsorption structure. The above results are supported by other evidences.     

Effects of potassium on the chemisorption of CO2 and CO on the Mo2C/Mo(100) surface

The interaction of CO₂ with K-promoted Mo₂C/Mo(100) has been studied with high-resolution electron energy loss spectroscopy, work function measurements and temperature-programmed desorption. Pre-adsorbed potassium dramatically affects the adsorption behavior of CO₂ on the Mo₂C/Mo(100) surface. It increases the rate of adsorption, the binding energy of CO₂ and it induces the dissociation of CO₂ through the formation of negatively charged CO₂. Potassium adatoms also promote the dissociation of adsorbed CO over Mo₂C. This revised version was published online in July 2006 with corrections to the Cover Date.     

Effects of space velocity on methanol synthesis from Co2/Co/H2 over Cu/ZnO/Al2O3 catalyst

The space velocity had profound and complicated effects on methanol synthesis from CO₂/CO/H₂ over Cu/ZnO/Al₂O₃ at 523 K and 3.0MPa. At high space velocities, methanol yields as well as the rate of methanol production increased continuously with increasing CO₂ concentration in the feed. Below a certain space velocity, methanol yields and reaction rates showed a maximum at CO₂ concentration of 5–10%. Different coverages of surface reaction intermediates on copper appeared to be responsible for this phenomenon. The space velocity that gave the maximal rate of methanol production also depended on the feed composition. Higher space velocity yielded higher rates for CO₂/ H₂ and the opposite effect was observed for the CO/H₂ feed. For CO₂/CO/H₂ feed, an optimal space velocity existed for obtaining the maximal rate.     

The effect of ZnO in methanol synthesis catalysts on Cu dispersion and the specific activity

The effect of ZnO in Cu/ZnO catalysts prepared by the coprecipitation method has been studied using measurements of the surface area of Cu, the specific activity for the methanol synthesis by hydrogenation of CO₂, and XRD. Although the Cu surface area increases with increasing ZnO content (0–50 wt%) as is generally known, the specific activity of the Cu/ZnO catalysts with various weight ratios of Cu:ZnO is greater than that of a ZnO-free Cu catalyst. These facts clearly indicate that the role of ZnO in Cu/ZnO catalysts can be ascribed to both increases in the Cu dispersion and the specific activity. The XRD results indicate the formation of a Cu–Zn alloy in the Cu particles of the Cu/ZnO catalysts, leading to the increase in specific activity. It is thus considered that the Cu–Zn surface alloy or a Cu–Zn site is the active site for methanol synthesis in addition to metallic copper atoms that catalyze several hydrogenation steps during the methanol synthesis. Furthermore, the advantage of the coprecipitation method through a precursor of aurichalcite is ascribed to both improvements in the Cu surface area and the specific activity. This revised version was published online in July 2006 with corrections to the Cover Date.     

Cu/Zn比对CuO/ZnO/ZrO_2催化CO_2加氢合成甲醇性能的影响

研究了不同Cu/Zn摩尔比对CO2加氢合成甲醇催化性能的影响。采用草酸凝胶共沉淀法制备了一系列不同Cu/Zn摩尔比的Cu O/Zn O/Zr O2催化剂,考察不同温度及Cu/Zn摩尔比对催化性能的影响,并结合X射线衍射(XRD)、N2物理吸附、程序升温还原(H2-TPR)和程序升温脱附(H2/CO2-TPD)技术对催化剂的结构和性质进行表征。结果表明:适宜的Cu/Zn摩尔比可以提高催化剂的反应性能。在513 K,2.0 MPa,n(H2)/n(CO2)=3/1和GHSV=4 800 h-1反应条件下,当R(Cu/Zn)=4时,Cu O/Zn O/Zr O2催化剂反应性能最好,CO2转化率高达17.8%,甲醇选择性高达67.8%。     

Methanol Synthesis from CO2, CO,and H2over Cu(100) and Ni/Cu(100)

The catalytic activity of Cu(100) and Ni/Cu(100) with respect to the methanol synthesis from various mixtures containing CO₂, CO, and H₂have been studied in a combined UHV/high pressure cell apparatus at reaction conditions,P_tot=1.5 bar andT=543 K. For the clean Cu(100) surface it is found that admission of CO to a reaction mixture containing CO₂and H₂does not lead to an increase in the rate of methanol formation, which indirectly suggests that the role of CO in the industrial methanol process relates to the change in reduction potential of the synthesis gas. For the Ni/Cu(100) surface it is found that Ni does not promote the rate of methanol formation from mixtures containing CO₂and H₂. In opposition, admission of CO to the reaction mixture leads to a significant increase in the rate of methanol formation with a turnover frequency/Ni site∼60×the turnover frequency/Cu site at Ni coverages below 0.1 ML making it a rather substantial promoting effect. It is found that the admission of CO to the synthesis gas creates segregation of Ni to the surface, whereas this is not the case for a reaction involving CO₂and H₂. It is suggested that CO acts strictly as a promotor in the system and we ascribe the increase in activity to a promotion through gas phase induced surface segregation of Ni.     

FTIR studies on the CO,CO2 and H2 co-adsorption over Ru-RuO x /TiO2 catalyst

FTIR spectra of a Ru-RuO_x/TiO₂ catalyst obtained on co-adsorption of CO, CO₂ and H₂ in the temperature range of 300–500 K were found to be the sum total of corresponding spectra observed during methanation of individual oxides. The two oxides compete for metal sites and at each temperature they reacted simultaneously to form distinct transient Ru(CO)_n type species even though the nature, the stability and the reactivity of these species were different in the two cases. The monocarbonyl species formed during adsorption/reaction of CO alone or of CO + H₂ were bonded more strongly than those formed during CO₂ + H₂ reaction.     

Photocatalytic reaction of H2O+CO2 over pure and doped Rh/TiO2

In the photocatalytic reduction of carbon dioxide to formic acid, formaldehyde and methanol in aqueous suspensions of TiO₂ and Rh/TiO₂, the effects of doping the TiO₂ with W⁶⁺ were investigated.This laboratory is a part of the Center for Catalysis, Surface and Material Science at the University of Szeged.     

Complexes in the Photocatalytic Reaction of CO(2) and H(2)O: Theoretical Studies

Complexes (H(2)O/CO(2), e-(H(2)O/CO(2)) and h(+)-(H(2)O/CO(2))) in the reaction system of CO(2) photoreduction with H(2)O were researched by B3LYP and MP2 methods along with natural bond orbital (NBO) analysis. Geometries of these complexes were optimized and frequencies analysis performed. H(2)O/CO(2) captured photo-induced electron and hole produced e-(H(2)O/CO(2)) and h(+)-(H(2)O/CO(2)), respectively. The results revealed that CO(2) and H(2)O molecules could be activated by the photo-induced electrons and holes, and each of these complexes possessed two isomers. Due to the effect of photo-induced electrons, the bond length of C=O and H-O were lengthened, while H-O bonds were shortened, influenced by holes. The infrared (IR) adsorption frequencies of these complexes were different from that of CO(2) and H(2)O, which might be attributed to the synergistic effect and which could not be captured experimentally.