A 2*4 all optical decoder switch based on photonic crystal ring resonators

Based on photonic crystal ring resonators and nonlinear Kerr effect in this paper, we proposed a 2*4 all optical decoder switch. Our proposed structure has two logic input ports and one bias input port. This decoder switch has four output ports. Via these two logic input ports, we control the bias signal to transfer toward which output port. We employed numerical methods such as plane wave expansion and finite difference time domain methods for analyzing the proposed structure.     

All-optical photonic crystal AND,XOR, and OR logic gates using nonlinear Kerr effect and ring resonators

In this article, two structures are proposed for all-optical AND, XOR, and OR logic gates based on nonlinear photonic crystals. The proposed structures include a Y-junction and ring resonator-based limiters. Two different structures are designed as the limiter in order to produce AND–XOR and AND–OR logic gates. Nonlinear rods of proposed structure have been used in order to create the frequency shift for different values of input power. Finite difference time domain method has been utilized to simulate the performance of proposed logic gates. Simulation results show that the smallest ON–OFF logic-level contrast ratio for the structures proposed for AND–XOR and AND–OR logic gates are 20.29 dB and 16.7 dB, respectively.     

Polarization beam splitter based on honeycomb-lattice photonic crystal ring resonators

A new polarization beam splitter is proposed based on a photonic crystal ring resonator (PCRR) composed of honeycomb-lattice cylindrical silicon rods in air. By shrinking the width of the bus waveguide and adjusting the radii of two nearest-neighbor center rods of the PCRR, an unpolarized beam can be separated well into TE and TM polarization states, respectively, at the backward and forward output ports. Simulation results obtained by the two-dimensional finite-difference time-domain technique show that the insertion losses are 3.58 dB and 3.08 dB, and the polarization extinction ratios are 21.42 dB and 28.53 dB for TE and TM polarization, respectively, at a 1566.7 nm center wavelength. The excess loss is less than 0.34 dB and its dimensions are roughly 43.2 μm × 27.52 μm. These findings offer potential practical applications in high-density photonic integrated circuits.     

Modal analysis of ultra-compact channel filters based on race-track photonic crystal ring resonators

A new channel drop filter (CDF) is proposed based on a race-track photonic crystal ring resonator composed of square-lattice cylindrical silicon rods in air. By using a two-dimensional finite-difference, time-domain numerical technique, the modal behavior of two representative CDFs, parallel and perpendicular, has been analyzed. The analyses include the impact of additional scatterer size, scatterer amount and their position on the performance of proposed CDFs, such as drop efficiency and quality factor (Q). For the parallel CDF, about 130 spectral Q and 99% drop efficiency can be optimally achieved at 1363?nm channel with 0.145 periodicity scatterer size, whereas for the perpendicular one, about 180 spectral Q and 99% drop efficiency can be optimally obtained at 1366?nm channel with 0.165 periodicity scatterer size. By increasing the number of scatterers, the efficiency of both configurations can be enhanced. No obvious variation is obtained by changing the scatterer position.     

A novel proposal for all-optical compact and fast XOR/XNOR gate based on photonic crystal

In this paper, we aim to design an all-optical device, which can perform XOR and XNOR functions in a single structure. The proposed structure will be realized by cascading two nonlinear resonant rings. The functionality of the proposed structure is based on controlling the optical behaviour of optical rings via optical intensity. The final structure has one bias and two input control ports, along with two output ports. One port acts as an XOR and the other acts as an XNOR gate. The maximum delay times for the XOR and XNOR gates are 1.5 and 2.5?ps, respectively. Therefore, the working bit rates for the XOR and XNOR gates are 666 and 400?Gbit/s, respectively.     

All-optical bistable switching based on photonic crystal slab nanocavity using nonlinear Kerr effect

In this paper, we propose all-optical bistable switching based on a two-dimensional (2D) photonic crystal slab nanocavity using the nonlinear Kerr effect with improved optical properties such as on/off ratio and switching power. The nonlinear properties of different kinds of nanocavity-based L3 structures are characterized. Using the 2D finite-difference time-domain method, we present a new structure of nanocavities for all-optical switching. The device has on/off ratio greater than 15?dB and power smaller than 375?mW for input optical pulses in the range of picoseconds.     

Tunable band-stop plasmonic filter based on square ring resonators in a metal-insulator-metal structure

A novel high-performance plasmonic filter based on a metal–insulator–metal structure is analysed for band-rejection applications. A square ring is used in proximity to the waveguide in order to resonate with some transmitted wavelengths and drop them to prevent from propagation towards the output. The effect of the structural parameters of square ring resonator is studied deploying the finite difference time domain method and the possibility of tuning the rejected wavelength is investigated in detail. The simulation results demonstrate that the rejected wavelength has a red-shift with increase in the size of the ring’s dimensions. A further study is carried out considering narrowing the bandwidth. To improve the quality factor of the proposed filter, a small ring within the resonator is introduced that considerably decreases the bandwidth of the peak with respect to its central wavelength.     

A novel pressure sensor based on series-coupled double microring resonators with a simple beam

We propose and analyse a novel optical pressure sensor based on series-coupled double microring resonators (SDMRRs) on a simple beam. The pressure applied on the sensor is measured through the change of the optical transmission spectrum at the output port. The optical transmission performances of the SDMRRs have been analysed and compared with the single and paralleled-coupled structures by the method of finite element analysis and numerical simulation. The simulation results showed that the stress sensitivity is 0.0225?kPa^–1 and linear measurement range of the sensor is 30?kPa. Furthermore, the influence of the amplitude transmission coefficient, half round phase shift and microring radius on the sensitivity have been investigated to optimize the sensor performance. This proposed sensor can be used for the smaller pressure detection in automotive, aerospace, oil/logging equipment and other harsh environmental application.     

A novel optical pressure sensor based on surface plasmon polariton resonator

We propose a Metal–Insulator–Metal structure consists of two surface plasmon polaritons (SPPs) and an H-shaped resonator. The reflectance spectrum is numerically simulated by the two-dimensional finite-difference time-domain method. The results show that this structure can act as a pressure sensor. To our knowledge, this is the first proposal to utilize the SPP resonator to form a pressure sensor. The size of the SPP resonator can be as small as a few hundred nanometers. The nano-scale pressure sensor opens a wide field for potential applications in biological and biomedical engineering.     

基于振动测试的非线性参数识别方法

研究了利用特殊的正弦扫频技术识别非线性参数的方法。该方法利用目前线性系统成熟的模态分析技术,并结合等效线性化理论,通过振动测试识别结构的非线性参数,可以建立一个更加准确的模型来反映非线性结构的动力学特性,从而提高模型的预测精度。该方法包括两部分：（1）常位移测试识别非线性刚度;（2）常速度测试识别非线性阻尼。常位移测试是在一次正弦扫频过程中,通过调整各频率下的激励力幅值使得位移响应的幅值为常数,获得一组频响函数,通过模态分析获得等效刚度;改变位移响应的幅值进行多次测试,获得多组等效刚度;对获得的一系列恒定位移响应下的等效刚度进行曲线拟合,即可获得所有线性和非线性刚度参数。常速度测试与其类似。以三自由度非线性系统为例,进行了常位移测试和     

A novel experimental set-up for turbidity sensing based on plastic optical fibre

A novel set-up for remote sensing the turbidity of a solution using plastic optical fibres together with a mirror is proposed. The authors have estimated turbidity of a liquid in terms of the nephelometric turbidity unit – NTU, a standard unit that relates the solution appearance with its turbidity for two proposed set-ups. Its performance was also investigated using clay sample measurements over a concentration range of 0–10 g/L. The proposed set-ups are useful for detection of suspended particles in a solution even in small quantities due to its high sensitivity, simplicity and robustness.     

A potential candidate design for nanosecond-order delay based on high-group index four rows optimized air holes line-defect photonic crystal waveguide

In order to meet the demand of ultra-high optical delay within a limited transmission distance, a high-group index line-defect photonic crystal waveguide (PCW) is designed. By adjusting the parameters of holes adjacent to the defect, a high constant group index about 680 and the corresponding flat bandwidth approximately 0.4 nm are obtained. Group velocity dispersion in the flat-band slow light region is in the order of 10⁹ ps²/km, which is non-negligible. Thus, the pulse broadening caused by dispersion that limits the transmission distance of the pulse in PCW is evaluated through broaden factor (BF). Considering the limitation of BF, a highest time delay up to 70.9 ps for 24 μm delay line is obtained. Assuming return-to-zero modulation format, the above optimized delay line supports a bit rate of the signal up to 12.9 bit/s. The study provides an important approach for realizing large time delay with small size using line-defect PCW.     

Ca4REO(BO3)3 crystals for green and blue microchip laser generation: from crystal growth to laser and nonlinear optical properties

We have taken advantage of congruent melting behavior of the nonlinear rare-earth oxoborate Ca₄REO(BO₃)₃ family to perfect a process of collective fabrication of self-frequency doubling microchip laser based on Nd:GdCOB (Ca₄Gd_1−xNd_xO(BO₃)₃) crystals. The process goes from Czochralski boule to 1 × 3 mm² chips perfectly oriented (better than 0.1°) to the phase matching direction (θ=90°, φ=46°) in the XY principal plane, with dielectric mirrors directly deposited on both faces of the chips. 20 mW of self-frequency doubling output power at 530 nm was performed under 800 mW of diode laser as incident pump power at 812 nm. In addition, new compositions from the solid solution Ca₄Gd_1−xY_xO(BO₃)₃ (Gd_1−xY_xCOB) (x=0.13, 0.16, 0.44) have been grown by the Czochralski pulling method, in order to achieve noncritical phase matching (NCPM) second harmonic generation of ⁴F_3/2 → ⁴I_9/2 Nd³⁺ doped laser hosts. Three types of laser wavelengths have been chosen: Nd:YAP (YAlO₃) at 930 nm, Nd:YAG (Y₃Al₅O₁₂) at 946 nm, and Nd:ASL (Nd_ySr_1−x La_x−yMg_x Al_12−xO₁₉) at 900 nm. Angular acceptance measurements of these three types of compositions present very large values, compared to pure GdCOB or YCOB oriented in critical phase matching configurations.     

A 3‐node C0 triangular element for the modified couple stress theory based on the smoothed finite element method

In this paper, a 3‐node C⁰ triangular element for the modified couple stress theory is proposed. Unlike the classical continuum theory, the second‐order derivative of displacement is included in the weak form of the equilibrium equations. Thus, the first‐order derivative of displacement, such as the rotation, should be approximated by a continuous function. In the proposed element, the derivative of the displacement is defined at a node using the node‐based smoothed finite element method. The derivative fields, continuous between elements and linear in an element, are approximated with the shape functions in element. Both the displacement field and the derivative field of displacement are expressed in terms of the displacement degree of freedom only. The element stiffness matrix is calculated using the newly defined derivative field. The performance of the proposed element is evaluated through various numerical examples.     

A novel modeling to predict the critical current behavior of Nb3Sn PIT strand under transverse load based on a scaling law and Finite Element Analysis

Superconducting Nb₃Sn Powder-In-Tube (PIT) strands could be used for the superconducting magnets of the next generation Large Hadron Collider. The strands are cabled into the typical flat Rutherford cable configuration. During the assembly of a magnet and its operation the strands experience not only longitudinal but also transverse load due to the pre-compression applied during the assembly and the Lorentz load felt when the magnets are energized. To properly design the magnets and guarantee their safe operation, mechanical load effects on the strand superconducting properties are studied extensively; particularly, many scaling laws based on tensile load experiments have been established to predict the critical current dependence on strain. However, the dependence of the superconducting properties on transverse load has not been extensively studied so far. One of the reasons is that transverse loading experiments are difficult to conduct due to the small diameter of the strand (about 1 mm) and the data currently available do not follow a common measurement standard making the comparison between different data sets difficult. Recently at the University of Geneva, a new device has been developed to characterize the critical current of Nb₃Sn strands under transverse loads. In this work we present a new 2D Finite Element Analysis (FEA) to predict the electro-mechanical response of a PIT strand that was tested at the University of Geneva when transverse load is applied. The FEA provides the strain map for the superconducting filaments when the load is applied. Those strain maps are then used to evaluate the critical current behavior of a PIT strand using a recently developed scaling law that correlates the superconducting properties of a wire with the strain invariants due to the load applied on the superconductor. The benefits and limitations of this method are discussed based on the comparison between the critical current simulation results obtained with the filament strain map and the experimental results available for PIT strands.     

A cell‐based smoothed discrete shear gap method (CS‐FEM‐DSG3) based on the C0‐type higher‐order shear deformation theory for dynamic responses of Mindlin plates on viscoelastic foundations subjected to a moving sprung vehicle

A cell‐based smoothed discrete shear gap method (CS‐FEM‐DSG3) based on the first‐order shear deformation theory (FSDT) was recently proposed for static and dynamic analyses of Mindlin plates. In this paper, the CS‐FEM‐DSG3 is extended to the C⁰‐type higher‐order shear deformation plate theory (C⁰‐HSDT) and is incorporated with damping–spring systems for dynamic responses of Mindlin plates on viscoelastic foundations subjected to a moving sprung vehicle. At each time step of dynamic analysis, one four‐step procedure is performed including the following: (1) transformation of the weight of a four‐wheel vehicle into the sprung masses at wheels; (2) dynamic analysis of the sprung mass of wheels to determine the contact forces; (3) transformation of the contact forces into loads at nodes of plate elements; and (4) dynamic analysis of the plate elements on viscoelastic foundations. The accuracy and reliability of the proposed method are verified by comparing its numerical solutions with those of other available numerical results. Copyright © 2014 John Wiley & Sons, Ltd.