Textural modification of soya bean/corn extrudates as affected by moisture content, screw speed and soya bean concentration

A Clextral BP‐10 (type BC45) co‐rotating twin‐screw extruder was used for texture modification of extrudates. Dry materials were mixed in a mixer for 15 min at low speed before extrusion. Moisture content 21–23% and addition of soya bean flour (0–40%) showed significant influences on the texture of the extrudates. Addition of soya bean flour in the range from 0 to 40% increased the diametrical expansion ratio (P < 0.01), decreased the hardness (P < 0.01) and modifies specific volume and chewing behaviours of the extrudates. Increasing moisture content in the range from 21 to 23%, however, significantly decreased specific volume (P < 0.01), and increases hardness (P < 0.01) of the extrudates. The hardness and crispness of the extrudates at fracturability of 110 g were graded higher than 6.0 by 30 and 27 of 34 consumer panelists, respectively. Consumer purchase intent showed the highest score of 5.5 in a 9‐point hedonic scale when sample fracturability was at 110 g.     

Texture and Microstructure of Cassava (Manihot esculenta Crantz) Flour Extrudate

Cassava flour (Manihot esculenta Crantz) was texturized by single-screw extrusion processing. Relationships between texture and micro-structure as a function of extrusion variables were examined. The effect of feed moisture or screw speed was significant (P < 0.01) on all textural parameters except springiness and energy first bite. Hardness, gumminess (P < 0.05) fracturability and cohesiveness (P < 0.01) decreased with increasing temperature. Hardness, fracturability and firmness were lowest at screw speed 520 rpm with feed rate 300g/min, 120–125°C and 11% feed moisture. Scanning electron micrographs showed structural change from a coarse cell mass at high feed moisture to a porous, thin-walled structure with decreased feed moisture.     

Correlation between instrumental and sensory ratings by evaluation of some texture reference scales

The objective of this study was to investigate instrumental–sensory relationships of some texture scales using argentine foods as references. Textural characteristics of these foods were instrumentally investigated by the texture profile analysis technique. Principal component analysis (PCA) was used to describe the main attributes of the food samples. High Pearson’s correlation coefficients were found between hardness and fracturability (r = 0.94; P < 0.0001), hardness and gumminess (r = 0.71; P < 0.0001) and springiness and cohesiveness (r = 0.85; P < 0.0001). PCA identified two significant principal components, which accounted for 81.2% of the variance in the instrumental data. Additionally, a trained panel described the texture characteristics of the food samples according to the standard reference scales. The correlation curves showed nonlinear relationships (R² between 85.6% and 99.9%) which were used to predict sensory attributes of other food samples. Some texture attributes like hardness and fracturability were accurately predicted by mechanical properties, while others like cohesiveness and adhesiveness were less representative.     

Comparative dry matter intake and nutrient utilisation efficiency in lactating cattle and buffaloes

An attempt was made to assess the comparative dry matter intake and nutrient utilisation efficiency of lactating buffaloes and cows based on results obtained from experimental feeding trials conducted in India. Data on dry matter (DM) intake, total digestible nutrient (TDN) intake, digestible crude protein (DCP) intake, body weight or metabolic body size (MBS), body weight change, milk yield or 4% fat‐corrected milk (FCM) yield, milk fat percentage and roughage/concentrate ratio in the diet of lactating buffaloes and cows were collected from published reports. The data were processed and analysed to assess the comparative dry matter intake and nutrient utilisation efficiency using suitable statistical analysis models. DM intake was significantly (P < 0.01) lower in buffaloes (2.57 kg DM per 100 kg body weight or 119.2 g kg^?1 MBS) than in cattle (3.09 kg DM per 100 kg body weight or 132.0 g kg^?1 MBS). Mean gross energetic efficiency (30.53 versus 27.83%; P < 0.01), gross protein efficiency (45.48 versus 37.06%; P < 0.01), net energetic efficiency (69.16 versus 64.10%; P < 0.05) and net protein efficiency (80.15 versus 59.59%; P < 0.001) were significantly higher in buffaloes than in cattle. Lactating buffaloes consumed significantly less (P < 0.001) protein (75.69 g DCP) and less (P < 0.01) energy (695.9 g TDN) than cows (93.89 g DCP, 774.8 g TDN) for production of 1 kg of 4% fat‐corrected milk. Buffaloes had higher energy and protein utilisation efficiencies as compared with cattle at similar fat‐corrected milk production level, plane of energy and protein nutrition, body size and body weight change. Buffaloes (1.189 kg DM kg^?1 4% FCM) consumed a similar (P > 0.05) amount of feed dry matter to that of cows (1.267 kg DM kg^?1 4% FCM). However, when DM intake kg^?1 FCM (4%) was compared at constant levels of metabolic body size, fat‐corrected milk, body weight change, dietary energy concentration and green forage percentage in the diet, lactating buffaloes consumed significantly less DM kg^?1 FCM yield as compared with cattle. It was concluded that DM intake was lower in lactating buffaloes. Moreover, lactating buffaloes utilised dietary dry matter, energy and protein for milk production more efficiently than cattle. © 2003 Society of Chemical Industry     

Nutritional contents of three edible oyster mushrooms grown on two substrates at Haramaya,Ethiopia, and sensory properties of boiled mushroom and mushroom sauce

The effects of wheat and bean straw growing substrates on nutrient contents of three edible oyster mushrooms and sensory properties of two mushroom foods were investigated. Moisture (fresh weight basis), crude protein, fat, fibre, ash, total carbohydrate, Fe, P and Zn (db) were ranged: 85.18–88.86%, 30.04–37.63%, 1.61–2.55%, 9.33–13.29%, 6.83–9.38%, 29.68–32.53%, 4.86–5.66 mg per 100 g, 12.39–15.36 g kg^?1 and 54.61–65.98 mg kg^?1, respectively. Moisture, fat and fibre were significantly (P < 0.01) affected by substrates, species and their interactions. Substrates showed no differences on ash, Fe and P (P > 0.05). Protein content was high for mushrooms grown on bean straw. Pleurotus sajor‐caju grown on bean straw had high protein, ash, Fe and P contents. No significant (P > 0.05) sensory acceptability differences were observed for boiled mushroom and mushroom sauce except colour of boiled mushrooms. In Ethiopia, if mushroom consumption is popularised, the support for food nutrition security is substantial.     

Characteristics and nutritional value of biscuits fortified with debittered salmon (Salmo salar) frame hydrolysate

Effect of debittered salmon frame hydrolysate (DSFH) at various levels (0, 5, 10, 15, 20 and 25 g/100 g) on physicochemical, textural, sensory and nutritional properties of biscuits was investigated. The highest thickness was obtained for the sample with 25 g/100 g DSFH (P < 0.05). There was no difference in diameter among all the biscuit samples (P > 0.05). The samples added with DSFH had lower weight, water activity and moisture content than the control (CONT, without DSFH) (P < 0.05). DSFH at 15 g/100 g showed no detrimental effect on sensory properties of resulting biscuits (DSFH-15). The DSFH-15 biscuit showed reduction in cutting force and fracturability. Scanning electron microscopic and cross-sectional images showed that DSFH-15 biscuit had more porous structure, compared to the CONT. The biscuits fortified with 15 g/100 g DSFH had higher protein but had lower energy value, fat and carbohydrate content than the CONT.     

Effects of selenium form on blood and milk selenium concentrations,milk component and milk fatty acid composition in dairy cows

BACKGROUND: Human health may be improved if milk with a favorable fatty acid composition and Se concentration is ingested. The present study is to determine how a basal diet supplemented with daily 5 mg Se as Se‐enriched yeast (SY) or sodium selenite (SS) affects the fatty acid composition and Se concentration of bovine milk. The effects of Se form on blood Se concentration, erythrocyte glutathione peroxidase 1 (GPx1) activity, serum GPx3 activity and milk yield and component were also studied. RESULTS: Both Se forms, when compared to control group, increased Se concentrations of blood (P < 0.01) and milk (P < 0.01), erythrocyte GPx1 activity (P < 0.05) and milk percentages of polyunsaturated fatty acids (PUFA) (P < 0.05) and cis‐9,cis‐12 linoleic acid (P < 0.05). Cows supplemented with SY had higher Se levels in blood (P < 0.01) and milk (P < 0.01) and percentage of PUFA in milk (P < 0.05) when compared with those supplemented with SS. Milk yield, milk component and serum GPx3 activity were not significantly affected by Se form. CONCLUSION: Supplementation of diet with SY appears to be of more benefit than SS in producing favorable milk with high PUFA and Se concentrations. Copyright © 2010 Society of Chemical Industry     

Effect of dietary sorghum germ meal on performance and meat quality of broiler chicks

Two hundred Lohmann broiler chicks were equally allocated into 20 pens after being adapted on a control diet for 7 days. The four dietary treatments containing graded levels of sorghum germ meal (SGM, 0, 75, 150, 225 g kg^?1) were randomly assigned to the pens (five pens per dietary treatment). L-Lysine and DL-methionine were added to the diets to raise their contents to the recommended levels for starter broiler chicks. Feed and water were provided ad libitum throughout the 6-week experimental period. The dietary treatment had negative linear effects (P < 0.01) on body weight, feed intake, weight gain, feed:gain ratio and dressing percentage, and a positive linear effect (P < 0.01) on liver and viscera relative weights. It had insignificant effects (P > 0.05) on pancreas, bursa relative weights, incidence of leg abnormalities and mortality rate. Abdominal fat relative weight had shown a significant negative linear effect (P < 0.05). Dietary SGM had no detectably different effect on colour, juiciness, tenderness and flavour of the meat when evaluated by semi-trained panellists.     

Texture characteristics and pizza bake properties of low-fat Mozzarella cheese as influenced by pre-acidification with citric acid and use of encapsulated and ropy exopolysaccharide producing cultures

Low-fat Mozzarella cheeses containing 6% fat were made by pre-acidification of milk with citric acid to pH 6.1 and using encapsulated ropy or non-ropy exopolysaccharide (EPS) producing Streptococcus thermophilus. Moisture retention, changes in texture profile analysis (TPA), meltability and stretchability of cheese, and changes in colour, surface scorching and shred fusion were analysed after baking over 90 days (d). Control cheeses and those made from pre-acidified milk without EPS cultures had the lowest moisture content at 54.84% and 55.28%, respectively. Control cheeses were hardest and their meltability and stretchability were initially low. Hardness was reduced and the melt and stretch distances increased with time. When baked, control cheeses showed incomplete shred fusion. Pre-acidification reduced hardness and increased meltability. Capsular- and ropy-EPS were quantified at 30.42 and 30.55 mg g⁻¹ of cheese, respectively, and increased moisture retention in pre-acidified cheese to 56.67% and 56.21%, respectively. These cheeses were softer and exhibited lower springiness. Greater meltability was observed initially but became similar to control cheeses after 90 d of storage. When baked after 45 d of storage, cheeses containing EPS producing cultures showed improved shred fusion, meltability and a reduction in surface scorching.     

Physicochemical analysis of full-fat, reduced-fat, and low-fat artisan-style goat cheese

The objective of this study was to examine the physicochemical properties of cheese elaborated via traditional artisan methods using goat milk containing 5, 1.5, or 0.4% fat and ripened for 1, 7, 14, or 28 d. Seventy-two cheeses were produced (2 batches × 3 fat levels × 4 ripening times × triplicate). Proximal composition, pH, texture analysis, and color were recorded in each cheese. Protein and moisture were increased in cheese, and fat and fat in DM were decreased with decreasing fat in milk. Internal and external pH was higher in low-fat and reduced-fat cheese, and pH values decreased during the first 2 wk of ripening but increased slightly on d 28. Cheese fracturability, cohesiveness, masticability, and hardness increased with decreasing fat, whereas elasticity and adhesiveness decreased. Cheese lightness and red and yellow indexes decreased with decreasing fat content; during ripening, lightness decreased further but yellow index increased.     

Porosity determination of deep‐fat‐fried coatings using pycnometer (Fried batter porosity determination by pycnometer)

The effect of processing conditions such as frying time and temperature, and batter formulation on pore development in deep‐fat fried chicken nuggets coatings were studied using helium pycnometer method. Chicken nuggets with preformed and laboratory prepared batter coatings were fried at temperatures between 170 and 190 °C for a time range between 0 and 240 s. There was significant (P < 0.05) effect of frying temperature and batter formulation on porosity. Porosity increased with frying time and temperature, and ranged between 2.15 and 47.92% for the preformed batter and 9.96 and 54.76% for the formulated batters. Apparent and bulk densities of the preformed batters increased and decreased with frying time, respectively, but both declined gradually with increasing frying temperature. As the level of rice flour in the formulation increased, apparent and bulk densities also increased. Batter formulation and frying temperature significantly (P < 0.05) influenced the variation in moisture and fat content of the fried batter. Porosity demonstrated positive and negative correlation with fat uptake and moisture loss, respectively, for all the batter coatings.     

Protein nutrition of dairy cows receiving grass silage diets: Effects of feeding a protein supplement of unbalanced amino acid composition

Eight cows were used in a replicated 4 × 4 latin square design experiment with period lengths of 3 weeks to investigate the effects of protein supplementation of a grass silage diet on silage intake and milk production. The four treatments were (i) the basal diet, consisting of grass silage ad libitum plus 2 kg day^?1 of molassed sugar beet pulp; (ii) basal diet plus 1 kg day^?1 of fish meal (F): (iii) basal diet plus 0.8 kg day^?1 of feather meal 1 (FE1); and (iv) basal diet plus 0.8 kg day^?1 of feather meal 2 (FE2). Silage intake was significantly (P < 0.01) increased by the F supplement but was not affected by the FE supplements; values were 9.9, 10.6, 9.6 and 9.6 kg DM day^?1 for basal, F, FE1 and FE2, respectively. Relative to the basal treatment, F increased (P < 0.001) the yield of milk and milk protein but, again, these were unaffected by FE; values were, for milk yield, 13.6, 16.3, 13.7 and 13.1 kg day^?1; and, for milk protein yield, 420, 545, 429 and 414 g day^?1 for basal, F, FE1 and FE2, respectively. However, supplementation with FE produced increases in the concentration (P < 0.001) and yield (P < 0.05) of milk fat; values were 42.8, 39.9, 46.6 and 47.8 g kg^?1 and 575, 646, 628 and 618 g day^?1 respectively, for the basal, F, FE1 and FE2 treatments. The profile of amino acids in blood plasma was characterised by markedly lower (at least P < 0.01) concentrations of methionine, lysine, tryptophan and histidine for the diets containing FE compared with F. The results show pronounced effects of the amino acid composition of the undegraded protein component of the supplement on both silage intake and milk production but also draw attention to a possible relationship between amino balance and the secretion of milk fat.     

Relationship of Water Content to Textural Characteristics, Water Activity, and Thermal Conductivity of Some Commercial Sausages

Mechanical properties from cyclic low strain testing, texture profile parameters and thermal conductivity were evaluated for 7 types of commercial sausage products ranging in moisture content from 27.7% to 62.4% and a_w from 0.857 to 0.993. Hardness, fracturability, the apparent moduli, stress al 20% compression, mechanical hysteresis loss, and strain energy all increased with decreasing moisture level, while springiness and the degree of elasticity decreased. Moisture had no significant effect on cohesiveness. A linear relationship was observed between the a_w and the effective mole fraction of water in the brine, the exact nature of which depended on the thermal process which the product had received. Thermal conductivity decreased with decreasing moisture in a linear manner.     

Milk composition traits in Jamunapari goats: Genetic parameters and effect of CSN1S1 gene variants

Milk protein polymorphism was analysed to improve the protein content in milk. The present study characterises the CSN1S1 gene and the effect of allelic combinations on milk composition traits in Jamunapari goats. The allelic variants obtained from sodium dodecyl sulfate polyacrylamide gel electrophoresis and polymerase chain reaction–restriction fragment length polymorphism were confirmed by cloning and sequencing. Genetic parameters were obtained from 518 records from 48 sires and 131 dams. The A, B and F alleles were observed in the population and the protein percentage in milk was significantly (P < 0.01) affected by allelic variants. The frequencies of A, B and F alleles were 0.456, 0.503 and 0.041, respectively. The protein content in milk was highest in the goats with AB genotype followed by AA > BB > BF > AF > FF. The goats with AB genotype had a significantly (P < 0.01) higher protein percentage in milk than goats with BF (t = 5.311, df = 113), AF (t = 8.13, df = 123) and FF (t = 9.55, df = 115) genotypes. The direct heritability for protein percentage was 0.441. Parity and season of birth had significant effects (P < 0.05) on the solids‐not‐fat percentage and lactose concentrations. The CSN1S1 AA, AB and BB genotypes should be selected for higher protein content and to improve milk quality and processing traits in Indian goats.     

Chemical and electrophoretic properties of Holstein cow milk as affected by somatic cell count

Chemical and electrophoretic properties of raw milk samples with different somatic cell counts (SCCs)(<200 000, 200 000–800 000 and >800 000 cells/mL) were determined. Milk was analysed for fat, lactose, total nitrogen (TN), non‐casein nitrogen (NCN), ratio of casein nitrogen to total nitrogen (CN/TN), pH, titratable acidity (TA), solid‐non‐fat (SNF), total solid (TS), the amount of α _s ‐casein and β‐casein. Milk SCC had no significant effect (P ≥ 0.05) on fat and TN. An increase in the SCC resulted in an increase in pH and NCN content, and a significant decrease in lactose, TA, SNF, CN/TN, α_s‐casein and β‐casein. Milk quality of Holstein dairy cattle deteriorate due to higher proteolytic activity associated with high SCC.     

Composition, yield, and functionality of reduced-fat Oaxaca cheese: effects of using skim milk or a dry milk protein concentrate

The effect of adding either skim milk or a commercial dry milk protein concentrate (MPC) to whole milk on the composition, yield, and functional properties of Mexican Oaxaca cheese were investigated. Five batches of Oaxaca cheeses were produced. One batch (the control) was produced from whole milk containing 3.5% fat and 9% nonfat solids (SNF). Two batches were produced from milk standardized with skim milk to 2.7 and 1.8% fat, maintaining the SNF content at 9%. In the other 2 batches, an MPC (40% protein content) was used to standardize the milk to a SNF content of 10 and 11%, maintaining the milk fat content at 3.5%. The use of either skim milk or MPC caused a significant decrease in the fat percentage in cheese. The use of skim milk or MPC showed a nonsignificant tendency to lower total solids and fat recoveries in cheese. Actual, dry matter, and moisture-adjusted cheese yields significantly decreased with skim milk addition, but increased with MPC addition. However, normalized yields adjusted to milk fat and protein reference levels did not show significant differences between treatments. Considering skim milk-added and control cheeses, actual yield increased with cheese milk fat content at a rate of 1.34 kg/kg of fat (R = 0.88). In addition, cheese milk fat and SNF:fat ratio proved to be strong individual predictors of cheese moisture-adjusted yield (r² ≈ 0.90). Taking into account the results obtained from control and MPC-added cheeses, a 2.0-kg cheese yield increase rate per kg of milk MPC protein was observed (R = 0.89), with TS and SNF being the strongest predictors for moisture adjusted yield (r² ≈ 0.77). Reduced-fat Oaxaca cheese functionality differed from that of controls. In unmelted reduced-fat cheeses, hardness and springiness increased. In melted reduced-fat cheeses, meltability and free oil increased, but stretchability decreased. These changes were related to differences in cheese composition, mainly fat in dry matter and calcium in SNF.     

Influence of protein concentration on surface composition and physico-chemical properties of spray-dried milk protein concentrate powders

Surface composition, moisture sorption behaviour and glass–rubber transition temperature (T_gr) were determined for spray-dried milk protein concentrate (MPC) powders over a range of protein contents (35–86 g 100 g⁻¹). Surface characterisation of MPC powders indicated that fat and protein were preferentially located on the surface of the powder particles, whereas lactose was located predominantly in the bulk. Moisture sorption analysis at 25 °C showed that MPC35 exhibited lactose crystallisation, whereas powders with higher protein contents did not and continually absorbed moisture upon humidification up to 90% RH. The GAB equation, fitted to sorption isotherms of MPCs, gave increases in monolayer moisture value (m_m) with protein content. T_gr, measured with a rheometer, decreased significantly (P < 0.05) with increasing water content and increased with increasing protein content (P < 0.05). In conclusion, increasing protein concentration of MPCs resulted in altered surface composition and increased m_m value and T_gr values.     

Comparison of buffalo cottage cheese made from aqueous extract of Withania coagulans with commercial calf rennet

An aqueous extract of Withania coagulans was used to prepare cottage cheese from buffalo milk and its quality attributes were compared with cheese made from commercial rennet. Both cheeses contain satisfactory ranges of 49.6–54.7% moisture, 21.3–24.3% fat and 21.4–23.6% protein. The type of coagulant had no significant effect on acidity, protein and ash contents of both the cheeses. W. coagulans cheese showed a significantly (P < 0.05%) higher pH and moisture contents. Similarly, no marked differences were observed in their organoleptic evaluation, actual and theoretical yield. These results supported the fact that W. coagulans is a promising rennet substitute for cottage cheesemaking.     

Effects of different genotypes at the CSN3 and LGB loci on milk and cheese-making characteristics of the bovine Cinisara breed

The Cinisara is an autochthonous Sicilian bovine breed reared mainly for production of Caciocavallo Palermitano, a typical stretched-curd cheese. The distribution of A and B alleles at both the β-lactoglobulin (LGB) and κ-casein (CSN3) loci in Cinisara cows and their influence on milk traits and cheese yield and composition were analysed. The LGB alleles are associated with significantly different effects on whey protein level (lower for BB genotype, P < 0.01), and casein index (higher value for BB genotype, P < 0.001), while CSN3 alleles were associated with significantly different effects on milk yield and coagulation properties; the BB genotype showed higher values for milk yield (P < 0.01) and curd firmness (a₃₀ P < 0.01 and a_2r P < 0.01) and lower values for coagulation and curd firming time (P < 0.01) than the AA genotype. Cheese made with LGB BB milk showed higher percentage protein recovery (P < 0.01); cheese made with CSN3 BB milk showed higher percentage fat recovery (P < 0.05).