Influence of aminothiazole additives in I/I3 redox electrolyte solution on Ru(II)-dye-sensitized nanocrystalline TiO2 solar cell performance

The influence of aminothiazole additives in acetonitrile solution of an I⁻/I₃⁻ redox electrolyte on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′- bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) (N719) dye-sensitized TiO₂ solar cell was studied. The current–voltage characteristics were investigated under AM 1.5 (100 mW/cm²) for nine different aminothiazole compounds. The aminothiazole additives tested had varying influences on the solar cell performance. Most of the additives enhanced the open-circuit photovoltage (V_oc), but reduced the short circuit photocurrent density (J_sc) of the solar cell. Both the physical and chemical properties of the aminothiazoles were computationally calculated in order to determine the reasons that the additive influenced solar cell performance. The larger the calculated partial charge of the nitrogen atom in the thiazole, the higher the V_oc value. The V_oc value increased as the dipole moment of aminothiazoles in acetonitrile increased. Moreover, the V_oc of the solar cell also increased as the size of the aminothiazole molecules decreased. These results suggest that the electron donicity of the aminothiazole additives influenced the interaction with the TiO₂ photoelectrode, which altered the dye-sensitized solar cell performance.     

Influence of alkylaminopyridine additives in electrolytes on dye-sensitized solar cell performance

The influence of alkylaminopyridine additives on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) dye-sensitized TiO₂ solar cell with an I⁻/I₃⁻ redox electrolyte in acetonitrile was studied. The current–voltage characteristics were measured for more than 20 different alkylaminopyridines under AM 1.5 (100 mW/cm²). The alkylaminopyridine additives tested had varying effects on the performance of the cell. All the additives decreased the short circuit photocurrent density (J_sc), but increased the open-circuit photovoltage (V_oc) of the solar cell. Molecular orbital calculations imply that the dipole moment of the alkylaminopyridine molecules influences the J_sc of the cell and that the size, solvent accessible surface area, and ionization energy all affect the V_oc of the cell. The highest V_oc of 0.88 V was observed in an electrolyte containing 4-pyrrolidinopyridine, which is comparable to the maximum V_oc of 0.9 V for a cell consisting of TiO₂ electrode and I⁻/I₃⁻ redox system.     

Influence of alkylpyridine additives in electrolyte solution on the performance of dye-sensitized solar cell

The influence of alkylpyridines additive to an I⁻/I₃⁻ redox electrolyte in acetonitrile on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) dye-sensitized TiO₂ solar cell was studied. I–V measurements were performed using more than 30 different alkylpyridines. The alkylpyridine additives showed a significant influence on the performance of the cell. All the additives decreased the short-circuit photocurrent (J_sc), but most of the alkylpyridines increased the open-circuit photovoltage (V_oc) and fill factor (ff) of the solar cell. The results of the molecular orbital calculations suggest that the dipole moment of the alkylpyridine molecules correlate with the J_sc of the cell. These results also suggest that both the size and ionization energy of pyridines correlate with the V_oc of the cell. Under AM 1.5 (100 mW/cm²), the highest solar energy conversion efficiency (η) of 7.6% was achieved by using 2-propylpyridine as an additive, which was more effective than the previously reported additive, 4-t-butylpyridine.     

Influence of electrolytes on the photovoltaic performance of organic dye-sensitized nanocrystalline TiO2 solar cells

We have studied the influence of electrolytes on the photovoltaic performance of mercurochrome-sensitized nanocrystalline TiO₂ solar cells using LiI, LiBr, and tetraalkylammonium iodides as the electrolyte. Short-circuit photocurrent density (J_sc) and open-circuit photovoltage (V_oc) depended strongly on the electrolyte. J_sc of 3.42 mA cm⁻² and V_oc of 0.52 V were obtained for the LiI electrolyte and J_sc of 2.10 mA cm⁻² and V_oc of 0.86 V were obtained for the Pr₄NI electrolyte. This difference in photovoltaic performance was due to the change in the conduction band level of the TiO₂ electrode. Large V_oc of 0.99 V was obtained for the LiBr electrolyte due to the large energy gap between the conduction band level of TiO₂ and the Br/Br₂ redox potential. Solar cell performance also depended strongly on organic solvent, suggesting that the physical properties of solvents such as Li ion conductivity and donor number affect photovoltaic performance.     

Manufacturing method for transparent electric windows using dye-sensitized TiO2 solar cells

The transparent electric windows based on dye-sensitized nanocrystalline TiO₂ solar cells have been prepared. The solar cell consists of dye-sensitized TiO₂ electrode with a TiO₂ layer of an about 8 μm thickness and of a 80×80 mm² active area, Pt counter electrode and redox electrolyte. The solar cell shows a transmittance of approximately 60% in the visible range and an open-circuit voltage (V_oc) of 0.64 V and a short-circuit photocurrent (J_sc) of 250 mA. A moderately transparent electric window composed of nine unit solar cells in series generates V_oc of 5.7 V and J_sc of 220 mA at one sun light intensity.     

Temperature dependence and the oscillatory behavior of the opto-electronic properties of a dye-sensitized nanocrystalline TiO2 solar cell

A dye-sensitized TiO₂ solar cell was developed and characterized. The I–V (current–voltage) characteristics were studied at different temperatures from −40°C to 80°C. The opto-electronic properties of the cell depend on factors like ambient temperature and the time constants of the redox processes at the cell interfaces. The temperature dependence of V_oc and I_sc were clearly demonstrated. I_sc increased with increasing temperature above room temperature, where as V_oc increased with decreasing temperature below room temperature. The opto-electronic properties showed oscillatory behavior especially at low temperatures, which may be attributed to the different velocities of the redox processes occurring at the TiO₂/dye, dye/electrolyte and the electrolyte/counter electrode interfaces.     

Characterization of CuInSe2/CdS thin-film solar cells prepared using CBD

CuInSe₂/CdS thin-film heterojunction solar cells were fabricated entirely by chemical bath deposition technique. The illuminated J−V characteristics of the devices prepared with different thicknesses of CdS and CuInSe₂ were studied. The typical solar cell parameters obtained for the best cell are: V_oc = 365 mV, J_sc = 12 mA/cm², FF = 61%, and η = 3.1% under an illumination of 85 mW/cm² on a cell of active area 0.1 cm². The J−V and C−V characteristics under dark condition and the spectral response were also studied for the best cell. The diode quality factor obtained is 1.7.     

Influence of alkyl dihalide gelators on solidification of dye-sensitized solar cells

Quasi-dye-sensitized solar cells were prepared by using ionic liquid-type electrolytes and gelators consisting of polyvinylpyridine and alkyl dihalides. Gelation occurred by the reaction of polyvinylpyridine and alkyl dihalides. When the chain length of the dihalides was varied, the short-circuit current (J_sc) increased with an increase in the chain length. However, the open-circuit voltage (V_oc) and fill factor (ff) slightly decreased. The increase in J_sc was brought about by the decrease in the interfacial resistances between the gel electrolyte and the counter electrode. In addition, the increase in the J_sc was explained by increases in the apparent diffusion coefficient of I⁻/I₃⁻ when the chain length increased. Decreases in V_oc and ff were explained by back-electron transfers from TiO₂ to iodine in the electrolytes. V_oc of the cells solidified by alkyldiiodide was lower than that solidified by alkyldichloride or alkyldibromide. It was explained by negatively shifted redox potential of I⁻/I₃⁻, compared with those for Cl⁻/Cl₂ or Br⁻/Br₂.     

Photosensitization of nanocrystalline TiO2 films by a polymer with two carboxylic groups, poly (3-thiophenemalonic acid)

Photovoltaic devices were assembled using a conducting polymer; poly (3-thiophenemalonic acid) sensitized TiO₂ electrodes and an electrolyte containing I₃⁻/I⁻ redox couple. This cell exhibited a short-circuit photocurrent (J_sc) of 6.65 mA cm⁻², an open circuit voltage (V_oc) of 355 mV and an efficiency of 1.5% under the illumination of 100 mW cm⁻² (AM 1.5). Addition of an ionic liquid, 1-methyl 3-n-hexylimidazolium iodide, into the electrolyte led to an improvement in the cell performances, achieving an overall efficiency of 1.8% under the same illumination. The average cell characteristics of the later devices are , with a fill factor of 0.65.     

Effect of a redox electrolyte in mixed solvents on the photovoltaic performance of a dye-sensitized solar cell

The effect of the iodide/triiodide redox electrolyte in various organic solvents on the photoelectrochemical properties of bis(tetrabutylammonium) cis-bis(thiocyanato)bis(4-carboxy-2,2′-bipyridine-4′-carboxylato)ruthenium(II)-sensitized nanocrystalline TiO₂ solar cells was studied. Solvents with large donor numbers dramatically enhanced the open-circuit voltage (V_oc), but usually reduced the short-circuit photocurrent density (J_sc). For a mixed solvent of tetrahydrofuran (THF) and acetonitrile, V_oc increased and the fill factor decreased with increasing THF concentration, but J_sc remained relatively constant. As the partial charge of the N or O atom of the solvent molecule increased, V_oc increased, but J_sc was unchanged up to a certain value of the partial charge (for THF, −0.46). For cells using 0.3 M 4-tert-butylpyridine and 20 vol% THF in the electrolyte, a short-circuit photocurrent density of 18.23 mA cm⁻², an open-circuit voltage of 0.73 V, a fill factor of 0.73, and an overall conversion efficiency of 9.74% were obtained.     

Highly efficient photon-to-electron conversion with mercurochrome-sensitized nanoporous oxide semiconductor solar cells

Dye-sensitized solar cells based on nanoporous oxide semiconductor thin films such as TiO₂, Nb₂O₅, ZnO, SnO₂, and In₂O₃ with mercurochrome as the sensitizer were investigated. Photovoltaic performance of the solar cell depended remarkably on the semiconductor materials. Mercurochrome can convert visible light in the range of 400–600 nm to electrons. A high incident photon-to-current efficiency (IPCE), 69%, was obtained at 510 nm for a mercurochrome-sensitized ZnO solar cell with an I⁻/I₃⁻ redox electrolyte. The solar energy conversion efficiency under AM1.5 (99 mW cm⁻²) reached 2.5% with a short-circuit photocurrent density (J_sc) of 7.44 mA cm⁻², a open-circuit photovoltage (V_oc) of 0.52 V, and a fill factor (ff) of 0.64. The J_sc for the cell increased with increasing thickness of semiconductor thin films due to increasing amount of dye, while the V_oc decreased due to increasing of loss of injected electrons due to recombination and the rate constant for reverse reaction. Dependence of photovoltaic performance of mercurochrome-sensitized solar cells on semiconductor particles, light intensity, and irradiation time were also investigated. High performance of mercurochrome-sensitized ZnO solar cells indicate that the combination of dye and semiconductor is very important for highly efficient dye-sensitized solar cells and mercurochrome is one of the best sensitizers for nanoporous ZnO photoelectrode. In addition, a possibility of organic dye-sensitized oxide semiconductor solar cells has been proposed as well as one using metal complexes.     

Semiconductor-sensitized solar cells based on nanocrystalline In2S3/In2O3 thin film electrodes

A possibility of semiconductor-sensitized thin film solar cells have been proposed. Nanocrystalline In₂S₃-modified In₂O₃ electrodes were prepared with sulfidation of In₂O₃ thin film electrodes under H₂S atmosphere. The band gap (E_g) of In₂S₃ estimated from the onset of the absorption spectrum was approximately 2.0 eV. The photovoltaic properties of a photoelectrochemical solar cell based on In₂S₃/In₂O₃ thin film electrodes and I⁻/I₃⁻ redox electrolytes were investigated. This photoelectrochemical cell could convert visible light of 400–700 nm to electron. A highly efficient incident photon-to-electron conversion efficiency (IPCE) of 33% was obtained at 410 nm. The solar energy conversion efficiency, η, under AM 1.5 (100 mW cm⁻²) was 0.31% with a short-circuit photocurrent density (J_sc) of 3.10 mA cm⁻², a open-circuit photovoltage (V_oc) of 0.26 V, and a fill factor ( ff ) of 0.38.     

Density functional study of alkylpyridine–iodine interaction and its implications in the open-circuit photovoltage of dye-sensitized solar cell

A density functional theory (DFT) method was used to study the monomer and intermolecular charge-transfer complexes of 22 different alkylpyridines with diiodine. DFT calculations revealed that the σ* orbital of iodine interacts with the nitrogen lone pair in pyridines. The open-circuit photovoltage (V_oc) values of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) (N719) dye-sensitized nanocrystalline TiO₂ solar cell with an I⁻/I₃⁻ redox electrolyte in acetonitrile using alkylpyridines additive were compared to computational calculations on the interaction between pyridines and I₂ by a DFT method. The optimized geometries, frequency analyses, Mulliken population analyses, and interaction energies suggest that the V_oc value of the solar cell is higher, the more alkylpyridine complexes with I₂.     

Photovoltaic characteristics of CuInS2/CdS solar cell by electron beam evaporation

When a CuInS₂/CdS solar cell was fabricated by depositing CdS thin film with dopant In of 1.0 at% on ternary compound CuInS₂ thin film with the lowest resistivity of 5.59 × 10⁻² Ωcm, its best result was as follows: V_oc = 461 mV, I_sc = 26.9 mA, FF = 0.685, η = 5.66% under the illumination of 100 mW/cm². And its series resistance and lattice mismatch was 5.1 Ω and 3.2%, respectively.Besides, a 4 layer structure solar cell of -CuInS₂/high -CuInS₂/high -CdS/low - CdS has been fabricated. When thickness of high - CuInS₂ was 0.2 μm, its best result was as follows: V_oc = 580 mV, I_sc = 30.6 mA, FF = 0.697, η = 8.25%. An its series resistance and lattice mismatch were 4.3 Ω and 2.8%, respectively.     

Anchorage of N3 dye-linked polyacrylic acid to TiO2/electrolyte interface for improvement in the performance of a dye-sensitized solar cell

A synthetic route was developed to link N3 dye to polyacrylic acid (PAA) using ethylenediamine (en) as the linker. The resulting complex, PAA–en–N3, was then coated onto a TiO₂ film. The modified TiO₂ film electrode (hereafter PAA–en–N3/TiO₂), when used as the photoanode in a dye-sensitized solar cell (DSSC), exhibited enhanced solar energy conversion efficiency compared with that of the usual DSSC with the N3/TiO₂ film electrode. The increase in efficiency was attributed to the increased open-circuit voltage (V_oc) and short-circuit photocurrent (J_sc). The increase in V_oc was attributed to the formation of a hydrophobic PAA–en–N3 layer on the TiO₂/electrolyte interface, while the increase in J_sc was attributed to the additional dye acquired by the TiO₂ film from the PAA–en–N3 complex.     

Hybrid solar cells based on MEH-PPV and thin film semiconductor oxides (TiO2, Nb2O5, ZnO, CeO2 and CeO2–TiO2): Performance improvement during long-time irradiation

Performance improvement of hybrid solar cells (HSC) applying five different thin film semiconductor oxides has been observed during long-time irradiation in ambient atmosphere. This behavior shows a direct relation between HSC and oxygen content from the environment. Photovoltaic devices were prepared as bi-layers of thin film semiconducting oxides (TiO₂, Nb₂O₅, ZnO, CeO₂–TiO₂ and CeO₂) and the polymer MEH-PPV, with a final device configuration of ITO/Oxide_{thin film}/MEH-PPV/Ag. The oxides were prepared as thin transparent films from sol–gel solutions. The photovoltaic cells were studied in ambient atmosphere by recording the initial values of open circuit voltage (V_oc) and current density (I_sc). Solar decay curves presented as the measurement of the short circuit current as a function of time, IV curves and photophysical analyses were also carried out for each type of device. Solar cells with TiO₂ thin films showed the best performance with maximum V_oc as high as −0.74 V and I_sc of 0.4 mA/cm². Solar decay analyses showed that the devices require a stabilization period of several hours in order to reach maximum performance. In the case of TiO₂, Nb₂O₅ and CeO₂–TiO₂, the maximum current density was observed after 15 h; for CeO₂, the maximum performance was observed after 30 h. The only exception was observed with devices applying ZnO in which the current density decreased drastically and degraded the polymer in just a couple of hours.     

Power output of Al/SnO2/n-Si solar cell

An Al/SnO₂/n-Si solar cell from n-type silicon (6.5 Ω-cm, 100) wafers using chemical vapour deposition (CVD) has been fabricated. The fabrication details, I–V characteristics determining conversion-efficiency (η_max), open circuit voltage (V_oc) and short circuit current (I_sc) have been presented. A maximum conversion efficiency of 6.3% for an unencapsulated cell of area 85.20 mm² has been obtained.     

On the use of triethylamine hydroiodide as a supporting electrolyte in dye-sensitized solar cells

For the first time, the application of a molten salt, triethylamine hydroiodide (THI), as a supporting electrolyte was investigated for the dye-sensitized solar cells (DSSCs). Titanium dioxide (TiO₂) electrode was modified by incorporation of high- and low-molecular weight poly(ethylene glycol) along with TiO₂ nanoparticles of two different sizes (300 nm (30 wt%) and 20 nm (70 wt%)). The highest apparent diffusion coefficient (D) of 8.12×10⁻⁶ cm² s⁻¹ was obtained for I⁻ (0.5 M of THI) from linear sweep voltammetry (LSV). Short-circuit current density (J_sc) increases with the concentration of THI whereas open-circuit potential (V_oc) remains the same. Optimum J_sc (19.28 mA cm⁻²) and V_oc (0.7 V) with a highest conversion efficiency (η) of 8.45% were obtained for the DSSC containing 0.5 M of THI/0.05 M I₂/0.5 M TBP in CH₃CN. It is also observed that the J_sc and η of the DSSC mainly relates with the D values of I⁻ and charge-transfer resistances such as R_ct1 and R_ct2 operating along Pt/TiO₂ electrolyte interface, obtained from LSV and electrochemical impedance spectroscopy (EIS). For comparison, tetraethylammonium iodide (TEAI) and LiI were also selected as supporting electrolytes. Though both the THI and TEAI have similar structures, replacement of one methyl group by hydrogen improves the efficiency of the DSSC containing the former electrolyte. Further, the DSSC containing THI exhibits higher J_sc and η than LiI (7.70%), from which it is concluded that THI may be used as an efficient and alternative candidate to replace LiI in the current research of DSSCs.     

Dye-sensitized solar cell based on Rose Bengal dye and nanocrystalline TiO2

Dye-sensitized solar cell is fabricated using Rose Bengal dye (RB) for sensitization of nanocrystalline TiO₂ and that imparts extension in spectral response towards visible region by modifying the semiconductor surface. Further, the photoresponse of the cell was evaluated by analyzing its J–V and impedance characteristics under illumination with metal halide light source of 400 W with an incident light of 73 mW/cm². Various photovoltaic parameters like J_sc, V_oc, FF were evaluated and found to be 3.22 mA, 890 mV, 0.53, respectively, resulting conversion efficiency (η) of 2.09%. Impedance analysis of the cell was carried out to investigate the internal resistance of the cell by recording Cole–Cole plots in between real and imaginary impedance in dark and with illumination under variable biasing, i.e. from 0 to 3 V.     

Effects of pH of a hybrid gel incorporated with 3-aminopropyltrimethoxysilane on the performance of a quasi-solid state dye-sensitized solar cell

Network hybrid gel prepared with tetraethyl orthosilicate, 3-aminopropyltrimethoxysilane (APS) and poly(ethylene glycol) was used as an electrolyte matrix in a quasi-solid state dye-sensitized solar cell (DSSC). Change in pH of this hybrid gel by varying the composition of APS was found to have remarkable effects on the photoelectrochemical performance of the cell. The hybrid gel matrix, having silane polymer backbones with free amine functionality, was characterized by FT-IR spectra and FE-SEM images, and the assembled DSSC by photocurrent-voltage and incident photon to current conversion efficiency curves. The unsealed, quasi-solid state DSSC with the hybrid gel has shown an increase in the open-circuit voltage (V_oc) and a steady decrease in the short-circuit photocurrent (J_sc), with increase in the content of APS. A maximum conversion efficiency of 4.5% was obtained for a DSSC by using 20% of APS in its hybrid gel at a light intensity of 100 mW cm⁻². Upon replacing the amino group of APS by bulkier aniline and benzophenoaniline groups, conversion efficiencies of the corresponding DSSCs were reduced. Variations in the V_oc and J_sc are explained in terms of shift of the flat band potential of TiO₂ and a complex formation between I₃⁻ and −NH₂ of APS of the electrolyte.