微柱群通道内饱和沸腾换热特性实验研究

为实现微小空间高效散热,本文以去离子水为工质,实验研究了工质流经高度和直径均为500μm的微圆柱组成的叉排微柱群通道时的饱和沸腾换热特性,并采用高速摄像机记录了通道内不同加热功率的气液两相流型,实验参数设定质量流速为341~598.3 kg/(m~2·s),热流密度为20~160 W/cm~2,蒸气干度为0~0.2。结果表明:随着热流密度增大,局部沸腾换热表面传热系数近似单调递减。在低干度区,局部沸腾换热表面传热系数随着质量流速的增加而增大,随着蒸气干度的增加而减小;受过冷沸腾气泡影响,工质进口温度越低,局部沸腾换热表面传热系数越大;随着热流密度增大,微柱群通道流动沸腾气泡流型依次为:泡状流、环状流,且泡状流区的局部沸腾换热表面传热系数明显高于环状流区。     

R32在水平管内流动沸腾换热特性的试验研究

对R32在水平光滑管和微肋管(外径均为7mm)内的沸腾换热特性展开试验研究,测试的制冷剂质量流速为100~250 kg/(m~2·s),饱和蒸发温度为7~11℃,热流密度为3~8 kW/m~2,测试管内制冷工质平均干度值为0~0.7。试验结果表明:热流密度是影响R32沸腾换热系数的主导因素之一,质量流速的增大、饱和蒸发温度的升高、热流密度的增大均有利于提高R32的沸腾换热系数;微肋管有强化传热的效果,其平均沸腾换热系数比光管增大11.8%~33.2%;干度对R32沸腾换热系数的影响比较复杂,R32的沸腾换热系数随干度的增加先增大后减小,这是由于出现了干涸值,本文试验测得的干涸值范围为0.41~0.57,制冷剂质量流速的降低和热流密度的增大均有利于干涸值的增大。     

水平微细管内CO_2蒸发相变传热干涸特性

本文在热流密度为7. 5～30 k W/m2、质量流率为300～600 kg/(m2·s)、饱和温度为-40～0℃、干度为0～1、内径为1. 5mm的试验工况条件下,对水平微细圆管内CO2在高干度区域干涸特性进行了实验研究。结果表明:质量流率的增加、热流密度的增加、饱和温度的升高均会导致干涸起始干度的减小。基于实验数据和干涸机理分析,获得新的临界热流密度理论预测计算模型和干涸干度理论预测模型,并对新的理论预测模型有效性进行验证,结果显示在试验工况范围内,新的理论预测模型预测效果较好。     

R290在水平微细圆管内沸腾换热特性研究

本文研究了R290在内径为1 mm、2 mm和4 mm水平微细圆管内的沸腾流动换热特性,在饱和温度为15℃条件下,质量流速为50～600 kg/(m~2·s)、干度为0～1、热流密度为5～20 k W/m~2时,对沸腾传热系数的影响进行了分析。通过实验发现,增大质量流速对传热系数具有增强作用,质量流速对传热系数的影响在低干度区域比高干度区域小。在热流密度方面,传热系数随着热流密度的增大而增大,且在1 mm和2 mm管内观察到了临界干度对传热系数的影响,这时传热系数有断崖式下降的趋势。在管径对于传热系数的影响方面,通过对不同管径换热特性的横向对比,发现在一定工况下传热系数随着管径的减小有所上升。此外本文还对R290已有的部分关联式进行了适配性验证。     

R404A在小管径管内流动沸腾换热特性研究

R404A在小管径管内的流动沸腾换热过程是一个极其复杂的物理现象。目前对R404A换热特性的研究大多集中在大管径上,对小管径换热特性的研究较少,且对不同实验现象的机理分析也不尽相同。因此R404A在小管径管内换热特性的理论研究仍需要大量具体的实验数据来支撑。本文通过搭建小管径内螺纹铜管蒸发实验台,研究R404A在小管径管内流动沸腾换热过程中不同热流密度、不同蒸发干度、不同质流密度、不同饱和温度对表面传热系数的影响,研究表明:热流密度、干度、质流密度、饱和温度均对R404A在小管径管内换热特性的影响较大,干涸现象发生前后这些因素产生的影响也不同。此外,这些因素对管内干涸现象发生的起始干度、沸腾主要换热形式以及干涸现象是否发生具有直接影响。     

水平细通道内CO_2流动沸腾换热流态特性实验研究

本文对水平细通道内CO_2流动沸腾换热过程中流态及其转变特性进行理论分析和可视化实验研究。根据可视化实验结果,更新了CO_2在低蒸发温度下的理论流动状态预测模型。实验工况为:热流密度(7. 5～30 k W/m2)、质量流率(50～600kg/(m2·s))、饱和温度(-40～0℃)、干度(0～1)、内径(1. 5 mm)。理论分析表明:质量流率对换热过程中经历的流态形式有决定性作用,热流密度对环状流-干涸区域、干涸区域-雾状流边界转变曲线影响较大,饱和温度对流态转变具有重要影响。可视化研究表明:基于理论流态图对于CO_2在细通道内流动沸腾换热的流态能够较好的预测,也能反映不同工况下流态的变化趋势,但理论流态图对干涸区域和雾状流区域预测偏差较大;在实验数据的基础上,增加了液气黏度比的无量纲因子,并提出一种新的临界热流密度预测模型。在考虑质量流率和热流密度影响的情况下,根据更新后临界热流密度预测模型和实验数据,引入沸腾数Bo对理论流态图中环状流-干涸区域、干涸区域-雾状流及间歇流/弹状流-环状流边界转变曲线进行了更新,可视化研究获得的流态数据中89. 4%符合更新后的CO_2理论流态预测模型。     

R717在小管径水平光管内流动沸腾换热及压降特性

氨制冷剂存在可燃性和毒性,因此减少其在制冷系统中的充注量极为重要。小管径换热管通常可以提供更高的表面传热系数,这可以作为提升换热器紧凑性同时减少系统中充注量的有效方法。本文搭建了氨制冷剂管内流动沸腾换热及压降测试实验装置,测试了氨制冷剂在4 mm水平光管内的流动沸腾换热及压降,并分析了干度、质量流速及热流密度对换热及压降特性的影响。结果表明:流动沸腾换热表面传热系数随着干度的增加而增大,同时质量流速和热流密度越高,流动沸腾换热表面传热系数越大。此外,氨制冷剂在管内的两相摩擦压降也随着干度的增加而增大,在固定干度下,质量流速的升高导致压降增大。     

CO2流动沸腾换热干涸研究进展

针对CO2在亚临界管内流动沸腾换热过程中所表现出来的干涸现象研究进展进行了综述,描述了在CO2沸腾换热过程中的干涸现象及其产生的影响因素,分析了热流密度、质量流量、饱和温度、管径等因素对干涸产生的影响及机理.提出CO2流动沸腾换热过程中临界热流密度,流态变化,干涸干度的预测以及抑制干涸提前发生的相应措施是今后研究的方向.     

微细管内CO2流动沸腾换热特性研究

针对CO2作为制冷剂在微细通道内流动沸腾换热进行了实验与理论研究,采用红外成像观测与换热系数实验研究定量与定性的分析了热流密度：2~35 kW/m2,饱和温度：﹣10 ℃ ~15 ℃工况时,内径为1 mm、2 mm圆管内的换热系数。实验结果表明：热流密度的增加强化了微细通道内工质核态沸腾换热,使换热系数得到显著提高;换热系数随饱和温度非单调变化,饱和温度较高时,越接近CO2临界温度其换热系数随饱和温度升高而增加,当饱和温度在低温工况时换热系数则随其降低而增加,换热过程中发生干涸干度随饱和温度升高而单调降低。     

R410A微通道内沸腾换热实验研究

在内径为2 mm的水平不锈钢微通道内对R410A的沸腾换热特性进行了实验研究。质量流率为200~600 kg/(m2·s),热流密度的范围为5~15 k W/m2,干度的范围为0.1~0.8,饱和温度为0℃和5℃。结果显示,当干度大于0.5时,随着热流密度的上升,沸腾换热系数显著上升,其平均增幅分别达到了4.6%和7.7%。当干度小于0.5时,热流密度对换热系数的影响十分微弱。随着质量流率的上升,换热系数均出现了小幅上升,其平均增幅也分别达到了1.1%和2%。而饱和温度对换热系数则几乎没有影响。随后,对可能的机理进行了讨论。实验结果又与Choi K I等以及Ebisu T等在内径分别为1.5 mm,3 mm和6.4mm管道内的研究结果进行了比较。结果显示,在相似工况下,随着管径的下降,当干度小于0.5时,换热系数呈现出上升的趋势,其平均增幅分别达到了18.4%,23.6%和19.5%。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Effect of Oxide Assisted Metal Nanoparticles on Microstructure and Morphology of Gallium oxide Nanowires

Several researches have been reported about the characteristic of β-Ga2O3 nanowires which was synthesized on nickel oxide particle. But indeed, recent researches about synthesis of β-Ga2O3 nanowires on oxide-assisted transition metal are limited to nickel or cobalt oxide catalyst. In this work, Gallium oxide (β-Ga2O3 ) nanowires were synthesized by a simple thermal evaporation method from gallium powder in the range of 700 - 1000℃ using the iron, nickel, copper, cobalt and zinc oxide as a catalyst, respectively. The β-Ga2O3 nanowires with single crystalline without defects were successfully synthesized at the reaction temperature of 850, 900 and 950℃ in all the catalysts. But optimum experimental condition in synthesis of nanowires varied with the kind of catalyst. As increasing synthesis temperature,the morphology of gallium oxide nanowires changed from nanowires to nanorods, and its diameter increased. From these results, we could be proposed that the growth mechanism of β-Ga2O3 nanowires was changed with synthesis temperature of nanowires. Microstructure and morphology of Synthesized nanowire was characterized by HR-TEM, FE-SEM, EDX and XRD.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from