Effect of GDC addition method on the properties of LSM–YSZ composite cathode support for solid oxide fuel cells

Equal amounts of Gd_0.1Ce_0.9O_2−δ (GDC) were added to La_0.65Sr_0.3MnO_3−δ/(Y₂O₃)_0.08(ZrO₂)_0.92 (LSM/YSZ) powder either by physical mixing or by sol–gel process, to produce a porous cathode support for solid oxide fuel cells (SOFCs). The effect of the GDC mixing method was analyzed in view of sinterability, thermal expansion coefficient, microstructure, porosity, and electrical conductivity of the LSM/YSZ composite. GDC infiltrated LSM/YSZ (G-LY) composite showed a highly porous microstructure when compared with mechanically mixed LSM/YSZ (LY) and LSM/YSZ/GDC (LYG) composites. The cathode support composites were used to fabricate the button SOFCs by slurry coating of YSZ electrolyte and a nickel/YSZ anode functional layer, followed by co-firing at 1250 °C. The G-LY composite cathode-supported SOFC showed maximum power densities of 215, 316, and 396 mW cm⁻² at 750, 800, and 850 °C, respectively, using dry hydrogen as fuel. Results showed that the GDC deposition by sol–gel process on LSM/YSZ powder before sintering is a promising technique for producing porous cathode support for the SOFCs.     

Ce0.9Gd0.1O1.95 supported La0.6Sr0.4Co0.2Fe0.8O3−δ cathodes for solid oxide fuel cells

Lanthanum-based iron- and cobalt-containing perovskite has a high potential as a cathode material because of its high electro-catalytic activity at a relatively low operating temperature in solid oxide fuel cells (SOFCs) (600–800). To enhance the electro-catalytic reduction of oxidants on La_0.6Sr_0.4Co_0.2Fe_0.8O_3?δ (LSCF), Ga doped ceria (Ce_0.9Gd_0.1O_1.95, GDC) supported LSCF (15LSCF/GDC) is successfully fabricated using an impregnation method with a ratio of 15 wt% LSCF and 85 wt% GDC. The cathodic polarization resistances of 15LSCF/GDC are 0.015 Ω cm², 0.03 Ω cm², 0.11 Ω cm², and 0.37 Ω cm² at 800 °C, 750 °C, 700 °C, and 650 °C, respectively. The simply mixed composite cathode with LSCF and GDC of the same compositions shows 0.05 Ω cm², 0.2 Ω cm², 0.56 Ω cm², and 1.20 Ω cm² at 800 °C, 750 °C, 700 °C, and 650 °C, respectively. The fuel cell performance of the SOFC with 15LSCF/GDC shows maximum power densities of 1.45 W cm^?2, 1.2 W cm^?2, and 0.8 W cm^?2 at 780 °C, 730 °C, and 680 °C, respectively. GDC supported LSCF (15LSCF/GDC) shows a higher fuel cell performance with small compositions of LSCF due to the extension of triple phase boundaries and effective building of an electronic path.     

A high performance solid oxide fuel cells operating at intermediate temperature with a modified interface between cathode and electrolyte

By adding 1% Bi₂O₃ (mol%) into LSCF (La_0.54Sr_0.44Co_0.2Fe_0.8O_3?δ), a layer of dense LSCF film is introduced to the upside of yttria stabilized zirconia (YSZ) electrolyte. The dense film increases the interface contact area and reduces the interface ion transfer resistance between cathode and electrolyte remarkably. As a result, the cell performance is greatly elevated from 492 to 901 mW cm^?2 at 650 °C. Besides, on the basis of careful observation of the cathode surface by FE-SEM, the function of Bi₂O₃ to promote the cathode sintering is speculated. The Bi₂O₃ and the LSCF come into being a kind of eutectic liquid. The eutectic liquid flows down from the cathode bulk to the interface between the cathode and the electrolyte where it accumulates to form a dense layer. This dense layer illuminates the function of adding Bi₂O₃ into LSCF cathode.     

Enhancement of the interfacial polarization resistance of La0.6Sr0.4Co0.2Fe0.8O3-δ cathode by microwave-assisted combustion method

Thermogravimetry, phase formation, microstructural evolution, specific surface area, and electrical properties of La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ (LSCF) cathode were studied as functions of its preparation technique. The pure perovskite LSCF cathode powder was synthesized through glycine–nitrate process (GNP) using microwave heating technique. Compared with conventional heating technique, microwave heating allows the rapid combustion to occur simultaneously between the nitrates and glycine in a controllable manner. The resulting powder is a single-phase nanocrystallite with a mean particle size of 113 nm and a high specific surface area of 12.2 m²/g, after calcination at 800 °C. Impedance analysis indicates that microwave heating has significantly reduced the polarization resistance of LSCF cathode. The area specific resistance (ASR) value of 0.059 and 0.097 Ω cm² at 800 °C and 750 °C, respectively, were observed. These values were twofold lower than the corresponding ASR of the cathode (0.133 and 0.259 Ω cm² at 800 °C and 750 °C, respectively) prepared through conventional heating. Results suggest that the microwave heating GNP strongly contributes to the enhancement of the LSCF cathode performance for intermediate temperature solid oxide fuel cells.     

Electrochemical performance of La2NiO4+δ cathode for intermediate-temperature solid oxide fuel cells

The application of the La₂NiO_4+δ (LNO), one of the Ruddlesden–Popper series materials, as a cathode material for intermediate temperature solid oxide fuel cells is investigated in detail. LNO is synthesized via a complex method using ethylenediaminetetraacetic acid (EDTA) and citric acid. The effect of the calcination temperature of the LNO powder and the sintering temperature of the LNO cathode layer on the anode-supported cell, Ni–YSZ/YSZ/GDC/LNO, is characterized in view of the charge transfer resistance and the mass transfer resistance. Charge transfer resistance was not significantly affected by calcination and sintering temperature when the sintering temperature was not lower than the calcination temperature. Mass transfer resistance was primarily governed by the sintering temperature. The unit cell with the LNO cathode sintered at 1100 °C with 900 °C-calcined powder presented the lowest polarization resistance for all the measured temperatures and exhibited the highest fuel cell performances, with values of 1.25, 0.815, 0.485, and 0.263 W cm⁻² for temperatures of 800, 750, 700, and 650 °C, respectively.     

Electro-spinning Pr0.4Sr0.6Co0.2Fe0.7Nb0.1O3−δ nanofibers infiltrated with Gd0.2Ce0.8O1.9 nanoparticles as cathode for intermediate temperature solid oxide fuel cell

Pr_0.4Sr_0.6Co_0.2Fe_0.7Nb_0.1O_3−δ (PSCFN) nanofibers and their corresponding Pr_0.4Sr_0.6Co_0.2Fe_0.7Nb_0.1O_3−δ–Gd_0.2Ce_0.8O_1.9 (PSCFN–GDC) composites have been synthesized and applied as cathodes for intermediate temperature solid oxide fuel cells (IT-SOFCs). In this paper, PSCFN nanofibers were obtained through electro-spinning and the following pyrolysis process. The resultant PSCFN nanofibers were infiltrated with GDC precursor to prepare nanofiber-structured PSCFN–GDC composite cathodes. The optimal PSCFN: GDC mass ratio of 1: 0.10 was identified to possess the lowest interfacial polarization resistances of 0.264, 0.155, 0.039 and 0.018 Ω cm² at 650, 700, 750 and 800 °C, respectively, lower than those of the PSCFN–GDC nanoparticle-structured composite cathode. The PSCFN–GDC (1: 0.10) shows an excellent stability of electrochemical activity under a current density of 200 mA cm⁻² for 100 h at 800 °C. All results proved that the nanofiber-structured PSCFN–GDC composite could act as a highly efficient cathode candidate for the IT-SOFCs.     

Application of a thin intermediate cathode layer prepared by inkjet printing for SOFCs

The application of an inkjet printing process for fabricating solid oxide fuel cell (SOFC) cathodes was investigated. Stably-dispersed LSCF–GDC inks were prepared by ball milling, and the composition was easily controlled by the preparation process. Fabrication of an LSCF–GDC layer was successfully carried out by depositing dots and the thickness was easily controlled by repeating printing process. A planar SOFC single cell with a double-layered cathode (comprised of a paste painted cathode layer and an inkjet printed interlayer) achieved a maximum power density of 0.71 W/cm² at 600 °C. This is the preliminary work for fabricating the cathode layer of a SOFC single cell via inkjet printing.     

Hydrogen formation from a real biogas using electrochemical cell with gadolinium-doped ceria porous electrolyte

The electrochemical cell consisting of a gadolinium-doped ceria (GDC, Ce_0.9Gd_0.1O_1.95) porous electrolyte, Ni–GDC cathode and Ru–GDC anode was applied for the dry-reforming (CH₄+CO₂→2H₂+2CO) of a real biogas (CH₄ 60.0%, CO₂ 37.5%, N₂ 2.5%) produced from waste sweet potato. The composition of the supplied gas was adjusted to CH₄/CO₂=1/1 volume ratio. The supplied gas changed continuously into a H₂–CO mixed fuel with H₂/CO=1/0.949–1/1.312 vol ratios at 800 °C for 24 h under the applied voltage of 1–2 V. The yield of the mixed fuel was higher than 80%. This dry-reforming reaction was thermodynamically controlled at 800 °C. The application of external voltage assisted the reduction of NiO and the elimination of solid carbon deposited slightly in the cathode. The decrease of heating temperature to 700 °C reduced gradually the fraction of the H₂–CO fuel (61.3–18.6%) within 24 h. Because the Gibbs free energy change was calculated to be negative values at 700–600 °C, the above result at 700–600 °C originated from the gradual deposition of carbon over Ni catalyst through the competitive parallel reactions (CH₄→C+2H₂, 2CO→C+CO₂). The application of external voltage decreased the formation temperature of carbon by the disproportionation of CO gas. At 600 °C, the H₂–CO fuel based on the Faraday's law was produced continuously by the electrochemical reforming of the biogas.     

Development of solid oxide cells by co-sintering of GDC diffusion barriers with LSCF air electrode

The effects of a Cu-based additive and nano-Gd-doped ceria (GDC) sol on the sintering temperature for the construction of solid oxide cells (SOCs) were investigated. A GDC buffer layer with 0.25–2 mol% CuO as a sintering aid was prepared by reacting GDC powder and a CuN₂O₆ solution, followed by heating at 600 °C. The sintering of the CuO-added GDC powder was optimized by investigating linear shrinkage, microstructure, grain size, ionic conductivity, and activation energy at temperatures ranging from 1000 to 1400 °C. The sintering temperature of the CuO–GDC buffer layer was decreased from 1400 °C to 1100 °C by adding the CuO sintering aid at levels exceeding 0.25 mol%. The ionic conductivity of the CuO–GDC electrolyte was maximized at 0.5 mol% CuO. However, the addition of CuO did not significantly affect the activation energy of the GDC buffer layer. Buffer layers with CuO-added GDC or nano-GDC sol-infiltrated GDC were fabricated and tested in co-sintering (1050 °C, air) with La_0.6Sr_0.4Co_0.2Fe_0.8O_3-δ (LSCF). In addition, SOC tests were performed using button cells (active area: 1 cm²) and five-cell (active area: 30 cm²/cell) stacks. The button cell exhibited the maximum power density of 0.89 W cm⁻² in solid oxide fuel cell (SOFC) mode. The stack demonstrated more than 1000 h of operation stability in solid oxide electrolysis cell (SOEC) mode (decay rate: 0.004%/kh).     

Fabrication and electrochemical properties of SOFC single cells using porous yttria-stabilized zirconia ceramic support layer coated with Ni

A porous yttria-stabilized zirconia (YSZ) ceramic supported single cell with a configuration of porous YSZ support layer coated with Ni/Ni–Ce_0.8Sm_0.2O_1.9 (SDC) anode/YSZ/SDC bi-layer electrolyte/La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ cathode was fabricated. The porosity, mechanical strength, and microstructure of porous YSZ ceramics were investigated with respect to the amount of poly(methyl methacrylate) (PMMA) used as a pore former. Porous YSZ ceramics with 56 vol.% PMMA showed a mechanical strength of 24 ± 3 MPa and a porosity of 37 ± 1%. The electrochemical properties of the single cell employing the porous YSZ support layer were measured using hydrogen and methane fuels, respectively. The single cell exhibited maximum power densities of 421 mW/cm² in hydrogen and 399 mW/cm² in methane at 800 °C. Moreover, at a current density of 550 mA/cm², the cell maintained 91% of its initial voltage after operation in methane for 13 h at 700 °C.     

Evaluation of GdBaCuCo0.5Fe0.5O5+δ as cathode material for intermediate temperature solid oxide fuel cells

The GdBaCuCo_0.5Fe_0.5O_5+δ (GBCCF) layered perovskite oxide was evaluated as novel cathode for intermediate temperature solid oxide fuel cells (IT-SOFCs). Its electrical conductivity was 9–13 S cm^?1 at 650–800 °C in air. The average thermal expansion coefficient (TEC) of GBCCF was 14.4 × 10^?6 K^?1, which was close to that of the typical electrolyte material. The cathode polarization resistance of GBCCF was 0.650 Ω cm² at 750 °C and it decreases to 0.118 Ω cm² when Ce_0.9Gd_0.1O_1.95 (GDC) was added to form a GBCCF–GDC composite cathode. Preliminary results indicated that layered perovskite GBCCF was a promising alternative cathode material for IT-SOFCs.     

Oxygen Dissociation and Interfacial Transfer Rate on Performance of SOFCs with Metal‐Added (LaSr)(CoFe)O3‐(Ce,Gd)O2 – δ Cathodes

A solid oxide fuel cell (SOFC) unit is constructed with Ni‐Ce_0.9Gd_0.1O_{2 – δ} (GDC) as the anode, yttria‐stabilised zirconia (YSZ) as the electrolyte and Pt, Ag or Cu‐added La_0.58Sr_0.4Co_0.2Fe_0.8O_{3 – δ} (LSCF)–GDC as the cathode. The current–voltage measurements are performed at 800 °C. Cu addition leads to best SOFC performance. LSCF–GDC–Cu is better than LSCF–GDC and much better than GDC as the material of the cathode interlayer. Cu content of 2 wt.‐% leads to best SOFC performance. A cathode functional layer calcined at 800 °C is better than that calcined at higher temperature. Metal addition increases the O₂ dissociation reactivity but results in an interfacial resistance for O transfer. A balance between the rates of O₂ dissociation and interfacial O transfer is needed for best SOFC performance.     

Fabrication and evaluation of NiO/Y2O3-stabilized-ZrO2 hollow fibers for anode-supported micro-tubular solid oxide fuel cells

In this work NiO/3 mol% Y₂O₃–ZrO₂ (3YSZ) and NiO/8 mol% Y₂O₃–ZrO₂ (8YSZ) hollow fibers were prepared by phase-inversion. The effect of different kinds of YSZ (3YSZ and 8YSZ) on the porosity, electrical conductivity, shrinkage and flexural strength of the hollow fibers were systematically evaluated. When compared with Ni–8YSZ the porosity and shrinkage of Ni–3YSZ hollow fibers increases while the electrical conductivity decreases, while at the same time also exhibiting enhanced flexural strength. Single cells with Ni–3YSZ and Ni–8YSZ hollow fibers as the supported anode were successfully fabricated showing maximum power densities of 0.53 and 0.67 W cm⁻² at 800 °C, respectively. Furthermore, in order to improve the cell performance, a Ni–8YSZ anode functional layer was added between the electrolyte and Ni–YSZ hollow fiber. Here enhanced peak power densities of 0.79 and 0.73 W cm⁻² were achieved at 800 °C for single cells with Ni–3YSZ and Ni–8YSZ hollow fibers, respectively.     

Microstructure and Polarization Studies on Interlayer Free La0.65Sr0.3Co0.2Fe0.8O3–δ Cathodes Fabricated on Yttria Stabilized Zirconia by Solution Precursor Plasma Spraying

Nano‐structured cathodes of La_0.65Sr_0.3Co_0.2Fe_0.8O_3–δ (LSCF) are fabricated by solution precursor plasma spraying (SPPS) on yttria stabilized zirconia (YSZ) electrolytes (LSCF‐SPPS‐YSZ). Phase pure LSCF is obtained at all plasma power. Performances of LSCF‐SPPS‐YSZ cathodes are compared with conventionally prepared LSCF cathodes on YSZ (LSCF‐C‐YSZ) and gadolinium doped ceria (GDC) (LSCF‐C‐GDC) electrolytes. High R_p is observed in the LSCF‐C‐YSZ (∼42 Ohm cm² at 700 °C) followed by LSCF‐C‐GDC (R_p ∼ 1.5 Ohm cm² at 700 °C) cathodes. Performance of the LSCF‐SPPS‐YSZ cathodes (R_p ∼ 0.1 Ohm cm² at 700 °C) is found to be even superior to the performance of LSCF‐C‐GDC cathodes. High performance in LSCF‐SPPS‐YSZ cathodes is attributed to its nano‐structure and absence of any interfacial insulating phase which may be attributed to the low temperature at the interaction point of LSCF and YSZ and low interaction time between LSCF and YSZ during SPPS process. In the time scale of 100 h, no change in the polarization resistances is observed at 750 °C. Based on the literature and from the present studies it can be stated that SOFC with YSZ electrolyte and LSCF‐SPPS‐YSZ cathode can be operated at 750 °C for a longer duration of time and good performance can probably be achieved.     

Combustion synthesis and characterization of LSCF-based materials as cathode of intermediate temperature solid oxide fuel cells

Nanocrystalline SOFC cathode materials of perovskite family, La_1?xSr_xM_1?yCo_yO₃, where 0 < x ≤ 0.5, 0 < y ≤ 0.8 (M is transitional metal = Mn or Fe), have been synthesized at a relatively low temperature by combustion synthesis using alanine as a novel fuel. Detailed X-ray powder diffraction analyses show 47–96% phase purity in the as-synthesized powder and upon calcination at ～825 °C single-phase material is obtained wherein the nanocrystallinity (crystallite size ～19–24 nm) is retained. Densification studies of the materials are carried out within 900–1100 °C. The coefficient of thermal expansion (CTE) of these cathodes is measured. Electrical conductivity of the cathodes sintered at different temperatures are measured in the temperature range 700–900 °C and correlated with the density of the sintered materials. The electrochemical performances of Ni-YSZ anode-supported SOFC having YSZ electrolyte (～10 μm) with CGO interlayer (～15 μm) are studied with the developed cathodes in the temperature range 700–800 °C using H₂ as fuel and oxygen as oxidant. Highest current density of ～1.7 A/cm² is achieved during testing at 800 °C measured at 0.7 V with a cathode composition of La_0.5Sr_0.5Co_0.8Fe_0.2O₃. Precipitation of nanocrystalline grains over the core grains in porous microstructure of this cathode might be one of the reasons for such high cell performance.     

Synthesis and electrical properties of Ce1−xGdxO2−x/2 (x = 0.05–0.3) solid solutions prepared by a citrate–nitrate combustion method

Ce_1?xGd_xO_2?x/2 (GDC) powders with different Gd³⁺ contents (x = 0.05–0.3) were prepared by a simple citrate–nitrate combustion method. The influence of the Gd³⁺ doping content on the crystal structure and the electrical properties of GDC were examined. Many analysis techniques such as thermal analysis, X-ray diffraction, nitrogen adsorption analysis, scanning electron microscopy and AC impedance analysis were employed to characterize the GDC powders. The crystallization of the GDC solid solution occurred below 350 °C. The GDC powders calcined at 800 °C showed a typical cubic fluorite structure. The lattice parameter of GDC exhibited a linear relationship with the Gd³⁺ content. As compared with that sintered at other temperatures, the GDC pellet that sintered at 1300 °C had a high relative density of 97%, and showed finer microstructure. The conductivity of GDC was firstly increased and then decreased with the increase of the Gd³⁺ content. The sintered GDC sample with the Gd³⁺ content of 0.25 exhibited the highest conductivity of 1.27 × 10^?2 S cm^?1 at 600 °C.     

A support layer for solid oxide fuel cells

The use of a perforated, ceramic layer, laminated on top of a porous electrode, as a support structure for solid oxide fuel cells is described. The support layer can be used on either the anode or cathode side and allows for the fabrication of mechanically robust, impregnated electrodes. Using fuel cells based on yttria-stabilized zirconia (YSZ), we demonstrate that the support layer can be made from YSZ or from a composite of YSZ and La_0.3Sr_0.7TiO₃ (LST). It is shown that there is no solid-state reaction between LST and YSZ, even after calcination at 1550 °C. Unlike pure LST, LST–YSZ composites can form a laminated structure on porous YSZ. Unlike pure YSZ, a dense LST–YSZ composite with 60-wt% LST exhibited an electronic conductivity of 7.6 S/cm at 700 °C after reduction in H₂ at 1000 °C, making the composite layer attractive for current collection in anode-supported cells.     

Improvement on the phase stability,mechanical properties and thermal insulation of Y2O3-stabilized ZrO2 by Gd2O3 and Yb2O3 co-doping

Gd₂O₃ and Yb₂O₃ co-doped 3.5 mol% Y₂O₃–ZrO₂ and conventional 3.5 mol% Y₂O₃–ZrO₂ (YSZ) powders were synthesized by solid state reaction. The objective of this study was to improve the phase stability, mechanical properties and thermal insulation of YSZ. After heat treatment at 1500 °C for 10 h, 1 mol% Gd₂O₃–1 mol% Yb₂O₃ co-doped YSZ (1Gd1Yb-YSZ) had higher resistance to destabilization of metastable tetragonal phase than YSZ. The hardness of 5 mol% Gd₂O₃–1 mol% Yb₂O₃ co-doped YSZ (5Gd1Yb-YSZ) was higher than that of YSZ. Compared with YSZ, 1Gd1Yb-YSZ and 5Gd1Yb-YSZ exhibited lower thermal conductivity and shorter phonon mean free path. At 1300 °C, the thermal conductivity of 5Gd1Yb-YSZ was 1.23 W/m K, nearly 25% lower than that of YSZ (1.62 W/m K). Gd₂O₃ and Yb₂O₃ co-doped YSZ can be explored as a candidate material for thermal barrier coating applications.     

Preparation of ultra-fine Sm0.2Ce0.8O1.9 powder by a novel solid state reaction and fabrication of dense Sm0.2Ce0.8O1.9 electrolyte film

A novel solid state reaction was adopted to prepare Sm_0.2Ce_0.8O_1.9 (SDC) powder. A mixed oxalate Sm_0.2Ce_0.8(C₂O₄)_1.5·2H₂O was synthesized by milling a mixture of cerium acetate hydrate, samarium acetate hydrate, and oxalic acid for 5 h at room temperature. An ultra-fine SDC powder with the primary particle size of 5.5 nm was obtained at 300 °C. The ultra-low temperature for the formation of SDC phase was due to the atomic level mixture of the Sm³⁺ and Ce⁴⁺ ions. The crystal sizes of SDC powders at 300 °C, 550 °C, 800 °C, and 1050 °C were 5.5 nm, 11.4 nm, 24.1 nm and 37.5 nm, respectively. The sintering curves showed that the powder calcined at lower temperature was easier to be sintered owning to its smaller particle size. A solid oxide electrolytic cell (SOEC), comprising porous La_0.8Sr_0.2Cu_0.1Fe_0.9O_3−δ (LSCF) for substrate, LSCF–SDC for active electrode, SDC for electrolyte, and LSCF–SDC for symmetric electrode, was fabricated by dip-coating and co-sintering techniques. An extremely dense SDC film with the thickness of 20 μm was obtained at only 1200 °C, which was about 100–300 °C lower than the literatures׳ reports. The designed SOEC was proved to work effectively for decomposing NO (3500 ppm, balanced in N₂), 80% NO can be decomposed at 600 °C.     

Performance evaluation of Sm0.5Sr0.5CoO3−δ fibers with embedded Sm0.2Ce0.8O1.9 particles as a solid oxide fuel cell composite cathode

Sm_0.2Ce_0.8O_1.9 (SDC)–embedded Sm_0.5Sr_0.5CoO_3?δ (SSC) composite fibers were successfully fabricated by electrospinning using commercial SDC nanopowders and an SSC precursor gel containing polyvinyl alcohol (PVA) and hydrated metal nitrate. After calcination of the composite fibers at 800 °C, the fibers of 300 ± 80 nm in diameter with a well-developed SSC cubic-perovskite structure and fluorite SDC were successfully obtained. An anode-supported single cell composed of NiO–Gd_0.2Ce_0.8O_1.9 (GDC)/GDC/SSC–SDC fibers was fabricated, and its electrochemical performance was evaluated. The maximum power densities were 1250 and 360 mW/cm² at 700 and 550 °C, respectively, which we ascribe to the excellent properties of the SSC fibers with embedded SDC particles such as a highly porous and continuous structure promoting mass transport and a charge transfer reaction.