Thermoelectric properties of Re6GaxSeyTe15−y (0 ≤ x ≤ 2; 0 ≤ y ≤ 7.5)

Thermoelectric properties of Re₆Ga_xSe_yTe_15?y (0 ≤ x ≤ 2; 0 ≤ y ≤ 7.5) were studied in the temperature range 90–320 K. The measurements revealed p-type semi-conductivity in all samples. Relatively high values of the Seebeck coefficients, α, were obtained in all samples. The electrical resistivities and room temperature Seebeck coefficients increased as selenium concentrations increased, for each value of x. The room temperature Seebeck coefficients and resistivities decreased as gallium content increased, for each value of y. Low carrier concentrations were found at room temperatures, in agreement with large Seebeck coefficient values. Measurements suggested hopping conduction between 150 K and 280 K for all samples. Temperature dependences of the Seebeck coefficient below 150 K were accounted for by phonon drag effect. The power factors for the samples were calculated. Theoretical discussions of dependences of the measured quantities on temperature and composition are given. Usefulness of these materials as thermoelectrics is also discussed.     

Thermo-optical properties of LaMg1 − xNixAl11O19 (0 ≤ x ≤ 1) hexaaluminates for metallic thermal protection system

LaMg_1 ? xNi_xAl₁₁O₁₉ (x = 0, 0.25, 0.5, 0.75, 1) ceramics are fabricated by pressureless-sintering method at 1700 °C for 10 h in air. The microstructure and thermo-optical properties of LaMg_1 ? xNi_xAl₁₁O₁₉ ceramics are investigated by the X-ray diffraction, scanning electron microscopy and Fourier transform infrared spectroscopy measurements. The influence of NiO doping on structure and thermo-optical properties of LaMg_1 ? xNi_xAl₁₁O₁₉ ceramics is investigated. The partial substitution of Ni²⁺ for Mg²⁺ results in a significant increase in emissivity at low wavelengths as compared with unmodified LaMgAl₁₁O₁₉. When the Ni²⁺ content increases to x = 0.75 or above, LaMg_1 ? xNi_xAl₁₁O₁₉ ceramics have a high emissivity value above 0.70 at low wavelengths at 500 °C. The measured emissivity of all LaMg_1 ? xNi_xAl₁₁O₁₉ ceramics shows a similar trend in the wavelength range of 6 to 14 μm.     

Continuous BaTi1 − yZryO3 (0 ≤ y ≤ 1) nanocrystals synthesis in supercritical fluids for nanostructured lead-free ferroelectric ceramics

This paper addresses for the first time two of the main challenges in the field of electroceramics. The first one is the development of a continuous, fast and reliable synthesis method for producing sub-20 nm barium titanate zirconate (BaTi_1-yZr_yO₃ with 0 ≤ y ≤ 1–BTZ) nanocrystals over the whole solid solution, while keeping a narrow size distribution. The second one concerns the processing of dense and nanostructured lead free electroceramics highlighting the size effect on the crossover from ferroelectric to relaxor, in the case of grains smaller than 100 nm. This was achieved combining the supercritical fluid technology to produce in continuous and at moderate temperature (400 °C) BTZ nanocrystals, with Spark Plasma Sintering (SPS) to prevent grain growth during the sintering.     

Atomic diffusion in the Fe [0 0 1] ∑ = 5 (3 1 0) and (2 1 0) symmetric tilt grain boundary

Both the formation and diffusion activation energies of single vacancy migrating intra-layer and inter-layer near the Fe [0 0 1] Σ = 5 (3 1 0) and (2 1 0) symmetric tilt grain boundaries have been calculated by using the MAEAM and a MD method. From energy minimization, the vacancy concentration in the second layer is higher than the one in the other layers for both (3 1 0) and (2 1 0) STGBs. By the diffusion activation energies of the vacancies migrating intra-layer and inter-layer, the vacancies located from the first to the eighth layers of (3 1 0) STGB as well as the ones located from the first to the tenth layers of (2 1 0) STGB are favorably migrated to the second layer. Thus there is a vacancy aggregation tendency to the second layer near the grain boundary. For the vacancy migrating intra-layer and inter-layer, the influences of the grain boundary are respectively as far as to the fifth and eighth layers for (3 1 0) STGB as well as to the sixth and tenth layers for (2 1 0) STGB.     

In vitro biocompatibility and antimicrobial activity of wet chemically prepared Ca10−xAgx(PO4)6(OH)2 (0.0 ≤ x ≤ 0.5) hydroxyapatites

Herein, we report the effect of silver ions on the physical, antimicrobial and cytocompatibility properties of wet chemically synthesized silver doped Ca_10?xAg_x(PO₄)₆(OH)₂ (0.0 ≤ x ≤ 0.5) hydroxyapatites (HAp). Silver ions containing HAp exhibit the comparable density, hardness and enhanced antimicrobial properties, in comparison to parent HAp. The optical absorption measurements confirm the presence of silver ions in the doped compositions, which are responsible for as increased antimicrobial property of doped HAp materials for x > 0.3. The cytotoxicity behavior of the doped HAp was evaluated using mouse fibroblast (L929) cell line. The important result has been that doped HAp (x > 0.3) exhibit statistically (significant) lower cell viability in comparison to undoped HAp. However, no difference in cellular functionality on doped HAp surfaces, in terms of cell adhesion and proliferation could be qualitatively observed in reference to undoped HAp. In order to explain the observed antimicrobial and cell viability properties, the in vitro release of Ag⁺ ions has been quantified using Inductively Coupled Plasma-Atomic Emission Spectroscopy (ICP-AES) and solubility was measured by weight loss in acetate buffer solution.     

Synthesis and electrochemical performance of Li1+xNi0.5Mn0.3Co0.2O2+δ (0 ≤ x ≤ 0.15) cathode materials for lithium-ion batteries

In this work, layered lithium-excess materials Li_1+xNi_0.5Mn_0.3Co_0.2O_2+δ (x = 0, 0.05, 0.10 and 0.15), of spherical morphology with primary nanoparticles assembled in secondary microspheres, were synthesized by a coprecipitation method. The effects of lithium content on the structure and electrochemical performance of these materials were evaluated by employing X-ray diffraction (XRD), inductive coupled plasma (ICP), scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS) and galvanostatic charge/discharge tests. It is found that Li_1.10Ni_0.5Mn_0.3Co_0.2O_2+δ, i.e., Li[(Ni_0.5Mn_0.3Co_0.2)_0.95Li_0.05]O₂ showed the best electrochemical performance due to the highly ordered layered structure, reduced cation mixing and the lowest charge transfer resistance. Li_1.10Ni_0.5Mn_0.3Co_0.2O_2+δ delivered a discharge capacity of 145 mA h g^?1 at 125 mA g^?1 in the cut-off voltage of 2.5–4.3 V, and had a capacity retention of 100% after 50 cycles at room temperature.     

Physical and optical properties of Co2+, Ni2+ doped 20ZnO + xLi2O + (30 − x)K2O + 50B2O3 (5 ≤ x ≤ 25) glasses: Observation of mixed alkali effect

Co²⁺ and Ni²⁺ ions doped 20ZnO + xLi₂O + (30 ? x) K₂O + 50B₂O₃ (5 ≤ x ≤ 25) mol% glasses are prepared using melt quenching technique. Structural changes of the prepared glasses by addition of transition metal oxides, CoO and NiO are investigated by UV–vis–NIR, FT-IR spectroscopy and XRD. The XRD pattern indicates the amorphous nature of prepared glasses. FT-IR measurements of the all glasses revealed that the network structure of the glasses are mainly based on BO₃ and BO₄ units placed in different structural groups in which the BO₃ units being dominant. The optical absorption spectra suggest the site symmetry of Co²⁺ and Ni²⁺ ions in the glasses are near octahedral. Crystal field and inter-electronic repulsion parameters are also evaluated. The optical band gap and Urbach energies exhibited the mixed alkali effect. Various physical parameters such as density, refractive index, optical dielectric constant, polaron radius, electronic polarizability and inter-ionic distance are also determined.     

Crystal structure and thermal expansion of LaCr1−xMgxO3, 0 < x ≤ 0.25

Solid solution LaCr_1?xMg_xO₃, 0 < х ≤ 0.25 was prepared by heating stoichiometric amounts of appropriate oxides in air at 1400 °C, 48 h. At room temperature it crystallizes in orthorhombically distorted GdFeO₃-type structure (a ≈ √2 × a_per; b ≈ √2 × a_pe; c ≈ 2 × a_per, where a_per – perovskite subcell parameter). High-temperature X-ray powder diffraction (HT XRPD) and dilatometry revealed first order phase transition to rhombohedral perovskite phase (R-3c, a ≈ √2 × a_per, c ≈ 2√3 × a_per) at 260–311 °C (OR phase transition). Crystal structures of room-temperature orthorhombic and high-temperature rhombohedral phases for LaCr_0.75Mg_0.25O₃ were refined using HT XRPD data. Temperature of OR phase transition increases gradually with increasing of magnesium content. Low-temperature orthorhombic phase exhibits TEC lower in comparison with high-temperature rhombohedral one (e.g. for LaCr_0.85Mg_0.15O₃ TEC(O) = 8.8 ppm K^?1; TEC(R) = 11.6 ppm K^?1). TEC for rhombohedral phase increases with increasing magnesium content from 10.4 ppm K^?1 for LaCr_0.95Mg_0.05O₃ to 12.1 ppm K^?1 for LaCr_0.75Mg_0.25O₃.     

Measuring spectral transmission and refractive index of AgCl1−xBrx (0 ⩽ x ⩽ 1) and Ag1−xTlxBr1−xIx (0 ⩽ x ⩽ 0.05) at the wavelength of 10.6 μm

We measured the complex refractive index at the wavelength of 10.6 μm with the help of Fourier transform infrared spectroscopy for polycrystalline plates of the following compositions AgCl_1−xBr_x (0 ⩽ x ⩽ 1) and Ag_1−xTl_xBr_1−xI_x, where x varied from 0 to 0.05. In order to do it we chose a segment of the spectrum, which was recorded with a high resolution (0.5 cm⁻¹) using the HgCdTe detector and which had a set of 10 identical peaks. It is shown that the real part of the refractive index rises along with increasing the substituting component fraction in the solid solution from 1.99 to 2.17 for AgCl_1−xBr_x and from 2.17 to 2.24 within the range of TlI mole fraction up to 0.05 for Ag_1−xTl_xBr_1−xI_x. We considered errors introduced by the spectrometer resolution and the accuracy rating of the micrometer, which was used to measure sample thickness. It is seen in the spectra, recorded for the second system with a lower resolution and using a deuterated and l-alanine doped triglycine sulfate detector, that increasing the thallium monoiodide fraction results in widening the transmission range towards bigger wavelengths. We also plan to use the obtained refractive index values for simulating mid-infrared optical fibers, the polycrystalline structure of which is close to the structure of the plates under investigation.     

XPS and Mössbauer studies on BaSn1−xNbxO3 (x ≤ 0.100)

A few compositions of perovskite oxide BaSn_1?xNb_xO₃ (with x ≤ 0.10) system, prepared by solid state ceramic method, have been studied employing XPS and Mössbauer spectroscopy techniques. Mössbauer spectra of these compositions in the temperature range of 78–300 K reveal that the oxidation state of Sn is +4. In XPS measurements, compositions with x ≤ 0.010 show no evidence of Nb⁵⁺ signal whereas the compositions with x ≥ 0.050 show clear evidence of Nb⁵⁺ signals indicating some unreacted Nb₂O₅ component in the system. This confirms the earlier report where presence of small amount of unreacted Nb₂O₅ was predicted.     

Density functional study on the geometric features and growing pattern of AlnNm clusters (n = 1–4, m = 1–4, n + m ≤ 5)

The bonding features of Al_nN_m clusters (n = 1–4, m = 1–4, n + m ≤ 5) are studied within the framework of the density functional theory following a systematic growing mechanism. Various geometries are found to be more stable than structures reported elsewhere for small Al–N aggregates. In other cases, good agreement exists with results already reported by other authors. It is also found that Al–N clusters tend to grow mainly towards nonlinear bidimensional structures up to the pentamer. The ability to form triple N–N bonds is important for the relative stability of clusters as they grow. The growing patterns could be explained mainly in terms of electrophilic attacks of both Al and N atoms to the corresponding sites in the aggregates of lower size. It is found that atomic charges derived from molecular electrostatic potentials allow to rationalize the electrophilic attacks, being then useful to understand the growing paths followed by small Al–N clusters.     

Structural and electrical properties of high-quality 0.41 μm-thick InSb films grown on GaAs (1 0 0) substrate with InxAl1−xSb continuously graded buffer

High-quality InSb was grown on a GaAs (1 0 0) substrate with an InAlSb continuously graded buffer (CGB). The temperatures of In, Al K-cells and substrate were modified during the growth of InAlSb CGB. The cross-section TEM image reveals that the defects due to lattice-mismatch disappear near lateral structures in CGB. The measured electron mobility of 0.41 μm-thick InSb was 46,300 cm²/Vs at 300 K. These data surpass the electron mobility of state-of-the-art InSb grown by other methods with similar thickness of InSb.     

Microwave-assisted synthesis and characterization of Ti1 − xVxO2 (x = 0.0–0.10) nanopowders

Ti_1 ? xV_xO₂ (x = 0.0–0.10) nanopowders were successfully synthesized by a microwave-assisted sol–gel technique and their crystal structure and electronic structure were investigated. The products were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman and UV–Vis spectroscopy. The results revealed that TiO₂ powders maintained the anatase phase for calcination temperature below 600 °C, but gradually changed to the rutile phase above 800 °C. The formation of the rutile phase was completed at 1000 °C. For Ti_1 ? xV_xO₂ (x = 0.05) powders, the phase transformation appeared at 600 °C. The absorption edge of Ti_1 ? xV_xO₂ (x > 0) powders broadened to the visible region with increasing V concentration and a strong visible light absorption was obtained with 10% V doping. V doping and subsequent coexistence of both anatase and rutile phases in our Ti_1 ? xV_xO₂ nanoparticles are considered to be responsible for the enhanced absorption of visible light up to 800 nm.     

Novel SrCo1 − 2x(Fe,Nb)xO3 − δ (x = 0.05, 0.10) oxides targeting CO2 capture and O2 enrichment: Structural stability and oxygen sorption properties

The novel Fe/Nb co-doped SrCo_1 ? 2x(Fe,Nb)_xO_3 ? δ (x = 0.05, 0.10) perovskite oxides were synthesized by the solid-state method. Structural and chemical stability of the SrCo_1 ? 2x(Fe,Nb)_xO_3 ? δ (x = 0.05, 0.10) oxides were studied by differential scanning calorimetry (DSC), thermogravimetric analysis (TG) and X-ray diffraction (XRD). The results demonstrated that the structural and chemical stability of the Fe/Nb co-doped SrCo_1 ? 2x(Fe,Nb)_xO_3 ? δ (x = 0.05, 0.10) is improved significantly. The oxygen sorption properties of the SrCo_1 ? 2x(Fe,Nb)_xO_3 ? δ (x = 0.05, 0.10) oxides were investigated between 300–900 °C in air, and the high oxygen sorption capacity of 11.5 and 10.3 mL O₂ (STP)/g oxide, respectively, are obtained.     

Electronic structure of Cu100−xZrx (x = 40, 50, 60) metallic glasses

The electronic structure of Cu_100−xZr_x (x = 40, 50, 60) metallic glasses was investigated by ultraviolet photoelectron spectroscopy and X-ray photoemission spectroscopy, the valence band spectra of these alloys were analyzed by a large shift of the Cu d-band peaks to higher binding energies upon increasing Cu content. Photoemission experiments and first-principles calculations prove that the values of density of states at Fermi level of Cu_100−xZr_x metallic glasses are mainly dominated by Zr rather than Cu. This work will enlighten further research on understanding the inheritance of metallic glasses and designing new metallic glasses with unique properties.     

Phase transition in (1 − x)Bi(Mg1/2Ti1/2)O3-xPbTiO3 ceramics

The phase structure and phase transition of (1 ? x)Bi(Mg_1/2Ti_1/2)O₃-xPbTiO₃ (BMT-PT) ceramics with x = 0.0–0.42 were investigated. It was found that pure perovskite phases were achieved for x ≥ 0.28, while Bi₄Ti₃O₁₂ or Bi₁₂TiO₂₀ phase existed for x ≤ 0.15. The anomaly dielectric peaks were observed around 620 °C for BMT-(0.28–0.38)PT samples, thus phase transition in (1 ? x)Bi(Mg_1/2Ti_1/2)O₃-xPbTiO₃ ceramics was studied using thermal expansion. It was found that dielectric anomalies at ~ 620 °C were resulted from the phase transition of the second phase and defects inside samples.     

(Sm_(1-x)La_x)_2Ce_2O_7(0<x<1)固溶体的热物理性能

以La_2O_3、Sm_2O_3和CeO_2为原料,采用高温固相反应法制备了(Sm_(1-x)La_x)_2Ce_2O_7(0x1)系列固溶体。并对其相结构、显微组织、元素组成、热物理性能进行了研究。X射线衍射分析表明,所合成的(Sm_(1-x)La_x)_2Ce_2O_7(0x1)系列固溶体具有典型的单一缺陷萤石型结构。扫描电镜分析表明,其显微组织十分致密,相对致密度92%,且各元素摩尔比与其化学式比较接近。其热导率随着La_2O_3掺杂量的增加而降低,并明显低于Y_2O_3部分稳定ZrO_2的热导率。其在1 000℃时的热膨胀系数处于11.83×10~(-6)/K至12.86×10~(-6)/K之间,明显高于YSZ的9×10~(-6)/K。该系列固溶体良好的热物理性能,表明其有潜力用作新型热障涂层表面陶瓷层材料。