Dielectric properties of barium-titanate sintered from tribophysically activated powders

It has been well known that the tribophysical (mechanical) activation could be used as a method for modification of physicochemical properties of dispersed systems such as polycrystalline mixture of oxides. In this study, we consider the properties of BaTiO₃ obtained from tribophysically activated initial powders. The mixture of 50 mol% BaCO₃ and 50 mol% TiO₂ powders was tribophysically activated in high energy vibromill during 0, 3, 30, 90 and 180 min, calcinated at 800°C for 1 h and reaction sintered at 1100, 1200 and 1300°C for 2 h. The surface specific areas, densities (green and sintered), phase compositions and dielectric properties were evaluated.     

Sacrificial template synthesis of core-shell SrTiO3/TiO2 heterostructured microspheres photocatalyst

The core-shell SrTiO₃/TiO₂ heterostructure was obtained via a combined hydrothermal route and calcination treatment using amorphous spherical TiO₂ as both template and reactant. Adjusting the hydrothermal environments can control the morphology of the post-calcined sample when it is hydrothermally treated at 180 °C/3 h and 200 °C/6 h, respectively. Following the heat treatment at 700 °C/4 h, the obtained powder illustrates the core-shell heterostructure with a hierarchical surface, and the diameter of the microsphere is about 700 nm. This synthesizing route facilitates the formation of a concentration gradient of SrTiO₃ and TiO₂, and subsequently constructs a gradient energy level, which helps the samples exhibited an excellent de-colorize activity over the methylene blue. The possible formation mechanism of core-shell SrTiO₃/TiO₂ heterostructures was proposed to guide the further improvement of their photocatalytic activity.     

Environmental resistance of a Ti2AlC-type MAX phase in a high pressure burner rig

Alumina-forming commercial Ti₂AlC (MAXthal 211)™ phase samples were exposed in a jet-fueled, high pressure burner rig (HPBR) at 1100°, 1200°, and 1300 °C, operating at 6 atm (bar) and 25 m/s, in ∼10% water vapor. Weight change exhibited a rapid initial uptake associated with a TiO₂ transient phase followed by cubic kinetics of a slow-growing α-Al₂O₃ underlayer. The cubic rate constants, k_c, were approximately 20% of those measured in static thermo-balance furnace tests. A small recession rate of −0.012 mg/cm²/h was measured at 1300 °C for a pre-oxidized sample. The loss rate was ∼15% that observed for SiO₂ scales subject to volatile Si(OH)₄ formation for SiC tested under similar conditions. These kinetic features were fitted in a modified cubic-linear law. From thermodynamic, XRD, and SEM analyses, it is proposed that volatile TiO(OH)₂ was formed by the reaction of water vapor with TiO₂ and TiAl₂O₅ outer layers.     

Effect of annealing on the structure and magnetic properties of mechanically milled TiO2–Fe2O3 mixture

A mixture of Fe₂O₃ and TiO₂ oxides has been mechanically milled to form TiFe₂O₄ spinel phase. X-ray diffraction (XRD) pattern of the as-milled mixture shows the presence of both Fe₂O₃ and TiO₂ phases. The diffraction peaks become broader and their relative intensity drastically decreases due to the particle size reduction and accumulation of strains. The milled powder was then subjected to annealing at different temperatures (600, 750, 900, 1200 °C). Annealing at 600 °C and 750 °C does not show any significant change in the phase formation. Nonetheless, XRD patterns show a narrowing and an increase in the intensity of Fe₂O₃ peaks with respect to TiO₂, which was reflected by an evolution in particle nano-structure following SEM analysis. An increase in the intensity ratio of the major peaks belonging to Fe₂O₃ relative to the as-milled mixture, which was associated with a reduction of the amount of TiO₂, suggested a possible insertion of Ti into the Fe₂O₃ crystal lattice. However, in VSM measurements, annealing at 600 °C and 750 °C does not change the ferromagnetic phase but the effect of annealing was a notable reduction in the values of both Ms and Mr (saturation magnetization and remanence magnetization respectively) Ultimately, as the powder was heated to 900 °C a new phase seemed to have emerged, this phase was confirmed by SEM, XRD, and magnetic measurements (VSM) where it change phase from ferromagnetic to paramagnetic phase.     

Synthesis and characterization of mesoporous NiO2/ZrO2-CeO2 catalysts for total methane conversion

This work reports the synthesis and characterization of mesoporous NiO/ZrO₂^-CeO₂ composites. These materials are still being developed due to their excellent morphological and structural properties, especially for solid oxide fuel cells (SOFCs) anodes. A soft chemical route using a polymeric template was utilized to synthesize the samples. The structure after two different calcination processes at 400 °C and 540 °C was studied by X-ray diffraction and Rietveld refinement, before and after NiO loading. Nitrogen adsorption, scanning/transmission electron microscopy and small angle X-ray scattering revealed a nanocrystalline bi-phasic porous material. Temperature programmed reduction experiments showed higher Ni and Ce reduction values for samples calcined at 400 °C and 540 °C, respectively. Methane conversion values in the temperature range studied were similar for both calcination temperatures, showing 50% CH₄ conversion around 550 °C and 80% around 650 °C. However, a sample calcined at 400 °C exhibited better morphological and textural properties leading to an enhancement in NiO and CeO₂ reducibility that might be responsible for an improvement in oxygen surface exchange and gasification of carbon species in catalytic experiments.     

Dielectric and piezoelectric properties of low temperature synthesized iso-valent modified BT ceramics

Ba_(1?x)Y_xTiO₃ (where Y = Ca, Mg and Sr, x = 0.02, 0.04, 0.06 and 0.08) ferroelectric ceramic samples were synthesized in single perovskite phase by modified solid state reaction (MSSR) route. For single perovskite phase formation and dense grain morphology, 900 °C and 1300 °C were optimized as calcination and sintering temperatures. With the increase of substitutions% of Ca in BCT ceramic samples, the position of T_c increases slightly, whereas with the increase of Mg and Sr substitution% in BMT and BST systems, the position of T_c decreased but remains above RT. Decreased processing temperature with low temperature coefficient of capacitance made BCT ceramic samples useful for dielectric applications. Symmetric nature of the S–E loops indicated the increase of piezoelectric nature with the increase of Ca substitution% in BCT system.     

Microstructure and mechanical properties of ceramics obtained from chemically co-precipitated Al2O3-GdAlO3 nano-powders with eutectic composition

An efficient and flexible chemical co-precipitation method has been used to synthesize nanoscale Al₂O₃-GdAlO₃ powders with eutectic composition. The as-synthesized powders exhibit a highly dispersive and homogeneous distribution with an average particle size of 50 nm. The phase transition in the resulting powders strongly depends upon the calcination temperature. GdAlO₃ undergoes complete crystallization after calcination at 1050 °C, however, the diffraction peaks of α-Al₂O₃ are found at a relatively high calcination temperature of at least 1300 °C. The fully-densified Al₂O₃-GdAlO₃ ceramic with eutectic composition obtained by hot pressing the nanoscale powders at 1500 °C exhibits a room temperature flexural strength of 556 MPa, a Vickers hardness of 17.3 GPa and a fracture toughness of 7.5 MPa m^1/2. The high temperature flexural strength of the as-sintered Al₂O₃-GdAlO₃ ceramic is measured to be 515 MPa after bending tests at 1000 °C.     

Cellulose templating method for the preparation of La0.8Sr0.2Ga0.83Mg0.17O2.815 (LSGM) solid oxide electrolyte

La_0.8Sr_0.2Ga_0.83Mg_0.17O_2.815 (LSGM) materials are synthesized with a fast and facile cellulose templating method for the first time and characterized by XRD, EIS, Archimedes method and SEM–EDS. LSGM powders with a phase purity of 91.7 mol% are obtained after the calcination at 1300 °C for 12 h. SEM–EDS results indicate possible decomposition and reconstruction of the LSGM phase due to the diffusion of Sr-rich species to the grain boundaries for the sample sintered at 1500 °C for 6 h. Maximum conductivity value is found to be 4.2 × 10^?2 S cm^?1 at 800 °C for the sample calcined at 1300 °C for 12 h and sintered at 1400 °C for 6 h. Phase purity, stability and relative density are the important factors for obtaining high performance LSGM electrolytes. Therefore, cellulose templating method is a promising candidate for the preparation of LSGM electrolytes.     

Ni4Nb2O9 ceramics prepared by the reaction-sintering process

Fabrication of Ni₄Nb₂O₉ ceramics via a reaction-sintering process was investigated. A mixture of raw materials was sintered into ceramics by bypassing calcination and subsequent pulverization stages. Ni₄Nb₂O₉ phase appeared at 1300 °C and increased with increasing soak time. Ni₄Nb₂O₉ content was found >96% in 1350 °C/2 h sintering pellets. A density of 5.71 g/cm³ was obtained for pellets sintered at 1350 °C for 2 h. This reaches 96.5% of the theoretical density. As the sintering temperature increased to 1350 °C, an abnormal grain growth occurred and grains >100 μm could be found. ?_r of 15.4–16.9 are found in pellets sintered at 1200–1300 °C. Q × f increased from 9380 GHz in pellets sintered at 1200 °C to 14,650 GHz in pellets sintered at 1250 °C.     

Microstructure and mechanical properties of Al2O3–20 wt%Al2TiO5 composite prepared from alumina and titania nanopowders

In the present work, Al₂O₃–20 wt%Al₂TiO₅ composite was prepared from reaction sintering of alumina and titania nanopowders. The nano-sized raw powders were reconstituted into nanostructured particles by ball milling. Then, the nanostructured reconstituted powders were pressed and pressureless-sintered into bulk ceramics at 1300, 1400, 1500 °C for 2 h. The phase composition and microstructures of reconstituted powders and as-prepared ceramic composites were characterized by using X-ray diffractometer (XRD), scanning electron microscope (SEM), transmission electron microscope and energy-dispersive spectrometer (EDS). The microstructural analysis of the ceramic showed that the average grain size of the alumina–aluminium titanate composite increases with increasing the temperature. Also, SEM proved the existence of a proper interface between Al₂TiO₅ and Al₂O₃ grains and preferential distribution of aluminium titanate particles in the grain boundaries. XRD analysis indicated the absence of rutile titania in the sintered composite ensuring complete formation of aluminium titanate. The hardness of the samples sintered at 1300, 1400, 1500 °C were 4.8, 6.2 and 8.5 GPa, respectively.     

Preparation and characterisation of mixed matrix Al2O3- and TiO2-based ceramic membranes prepared using polymeric synthesis route

Al₂O₃- and TiO₂-based ceramic membranes prepared using polymeric synthesis route were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy, X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR) and gas permeability tests. The influence of the final calcination temperature and the systematic investigation of the properties of the membranes are provided. The calcination temperature affected morphological, structural and chemical properties, as well as the gas permeability of the ceramic membranes. XRD analysis revealed rhombohedral and tetragonal structures of Al₂O₃ and TiO₂-based ceramic, respectively, prepared at calcination temperatures of 1100 and 1200 °C. The TiO₂-based ceramic matrix calcined at temperatures of 1100 and 1200 °C exhibited a well-defined crystalline microstructure with the grains increasing in size as a function of temperature. FTIR analysis revealed that phosphorus additives in orthoclase clay tend to form phosphonate groups during the calcination process. The decomposition of organic source was not fulfilled as tested at calcination temperatures of 1000, 1100 and 1200 °C.     

Simultaneous catalytic removal of NOx and soot particulates over CuMgAl hydrotalcites derived mixed metal oxides

A series of CuMgAl hydrotalcites derived oxides were prepared by co-precipitation and calcination methods and tested for the simultaneous catalytic removal of NOx and soot. The obtained samples were characterized by XRD, N₂ adsorption-desorption, H₂-TPR and ICP-AES techniques. The crystal phases, porous structures and redox properties of the catalysts were strongly influenced by Cu substitution contents and calcination temperatures. The CuMgAl mixed oxides with mesoporous properties exhibit high activity for the simultaneous NOx-soot removal. Among the tested catalysts, 3.0Cu-800 sample shows the best performance with the ignition temperature of soot = 260 °C and the total amounts of N₂ = 6.0 × 10^− 5 mol. Based on the experimental work, a primitive kinetics analysis was carried out from the non-steady (dynamic) TPR measurements. Linear Arrhenius plots of rates of CO₂, N₂ and N₂O formation were observed around the onset of formation curves where the substantial amount of the soot still remains in the soot/catalyst mixture and the effective area of the soot/catalyst contact can be regarded as constant. Finally, a compensation effect was found for the formation of CO₂, N₂ and N₂O over CuMgAl mixed oxides with CuO as the predominant phase.     

Microwave dielectric properties of nanocrystalline TiO2 prepared using spark plasma sintering

TiO₂ bulk ceramics were fabricated by using both spark plasma sintering (SPS) and the conventional sintering method (CSM). Starting materials were ultra fine rutile powders (<50 nm) prepared via the sol–gel process. CSM achieved the relative sintering density of 99.2% at 1300 °C. The grain size of 1300 °C sintered specimen was 6.5 μm. However, the sintering temperature of SPS for the density of 99.1% was as low as 760 °C, where the grain size was only 300 nm. In order to re-oxidize the Ti³⁺ ions due to the reducing atmosphere of the SPS process and the high temperature of the CSM process, the prepared TiO₂ specimens were annealed in an oxygen atmosphere. The dielectric constant (ɛ_r) and quality factor (Q × f) of SPS-TiO₂ re-oxidized specimens in a microwave regime were 112.6 and 26,000, respectively. These properties were comparable to those of 1300 °C sintered CSM specimens (ɛ_r ∼ 101.3, Q × f ∼ 41,600). These microwave dielectric properties of nanocrystalline TiO₂ specimens prepared using SPS were discussed in terms of grain size variation and Ti⁴⁺ reduction.     

Low temperature sintering and microwave dielectric properties of TiO2 ceramics

The TiO₂ ceramics were prepared by a solid-state reaction in the temperature range of 920–1100 °C for 2 h and 5 h using TiO₂ nano-particles (Degussa-P25 TiO₂) as the starting materials. The sinterability and microwave properties of the TiO₂ ceramics as a function of the sintering temperature were studied. It was demonstrated that the rutile phase TiO₂ ceramics with good compactness could be readily synthesized from the Degussa-P25 TiO₂ powder in the temperature range of 920–1100 °C without the addition of any glasses. Moreover, the TiO₂ ceramics sintered at 1100 °C/2 h and 920 °C/5 h demonstrated excellent microwave dielectric properties, such as permittivity (Ɛ_r) value >100, Q × f  > 23,000 GHz and τ_f ≅ 200 ppm/°C.     

Decomposition of nonionic surfactant on a nitrogen-doped photocatalyst under visible-light irradiation

A visible-light-active N-containing TiO₂ photocatalysts were prepared from crude amorphous titanium dioxide by heating amorphous TiO₂ in gaseous NH₃ atmosphere. The calcination temperatures ranged from 200 to 1000 °C, respectively. UV–vis/DR spectra indicated that the N-doped catalysts prepared at temperatures <400 °C absorbed only UV light (E_g = 3.3 eV), whereas samples prepared at temperatures ≥400 °C absorbed both, UV (E_g = 3.10–3.31 eV) and vis (E_g = 2.54–2.66 eV) light. The chemical structure of the modified photocatalysts was investigated using FT-IR/DRS spectroscopy. All the spectra exhibited bands indicating nitrogen presence in the catalysts structure. The photocatalytic activity of the investigated catalysts was determined on a basis of a decomposition rate of nonionic surfactant (polyoxyethylenenonylphenol ether, Rokafenol N9). The most photoactive catalysts were those calcinated at 300, 500 and 600 °C. For the catalysts heated at temperatures of 500 and 600 °C Rokafenol N9 removal was equal to 61 and 60%, whereas TOC removal amounted to 40 and 35%, respectively. In case of the catalyst calcinated at 300 °C surfactant was degraded by 54% and TOC was removed by 35%. The phase composition of the most active photocatalysts was as follows: (a) catalyst calcinated at 300 °C—49.1% of amorphous TiO₂, 47.4% of anatase and 3.5% of rutile; (b) catalyst calcinated at 500 °C—7.1% of amorphous TiO₂, 89.4% of anatase and 3.5% of rutile; (c) catalyst calcinated at 600 °C—94.2% of anatase and 5.8% of rutile.     

Thermally stable ceria–zirconia catalysts for soot oxidation by O2

Ce–Zr mixed oxides calcined at 1000 °C are more active catalysts for soot oxidation than pure CeO₂ calcined at the same temperature, both in loose and tight contact between soot and catalyst. 1000 °C sinterised-CeO₂ presents a very low surface area (2 m²/g), a large crystal size (110 nm) and a lack of surface redox properties. Ce–Zr mixed oxides present higher BET surface areas (typically 17–19 m²/g), smaller crystal sizes and enhanced redox properties. The Zr molar fraction does not affect appreciably the catalytic activity of Ce–Zr mixed oxides in the range studied (Zr molar fraction from 0.11 to 0.51).     

Sintering behavior and dielectric properties of KCa2Nb3O10 ceramics

Dense KCa₂Nb₃O₁₀ (KCN) oxides were synthesized and their dielectric properties were investigated. A homogeneous KCN phase was formed in the specimen sintered above 1300 °C, but a CaNb₂O₆ secondary phase was developed in the specimen sintered at 1400 °C, as result of the evaporation of K₂O. The KCN oxides sintered at 1375 °C showed a high relative density that was 97.1% of the theoretical density. Furthermore, liquid-phase-assisted abnormal grain growth occurred during sintering. The dielectric constant of this KCN oxide was 46, with a low dielectric loss of 0.9% at 100 kHz; these values are smaller than those that were previously reported. Complex impedance analysis indicated that the resistivity of the KCN oxide was very low, probably as a result of the presence of K⁺ ions between the layers, and this could be the origin of the low-frequency dispersion of the KCN oxides.     

Effect of calcination temperature on the fabrication of transparent lutetium titanate by spark plasma sintering

Transparent lutetium titanate (Lu₂Ti₂O₇) bodies were fabricated by spark plasma sintering using Lu₂O₃ and TiO₂ powders calcined from 700 °C to 1200 °C. No solid-state reaction was identified after calcination at 700 °C, whereas single-phase Lu₂Ti₂O₇ powder was prepared at 1100 and 1200 °C. The calcination at 700 °C promoted densification at the early stages of sintering, whereas residual pores at grain boundaries resulted in Lu₂Ti₂O₇ bodies with low transparency. Low-density and opaque Lu₂Ti₂O₇ bodies formed owing to the coarsening of the powder calcined at 1200 °C. The Lu₂Ti₂O₇ body sintered using the powder calcined at the moderate temperature of 1100 °C had a density of 99.5% with the highest transmittances of 41% and 74% at wavelengths of 550 nm and 2000 nm, respectively.     

Poly(N-isopropylacrylamide) assisted microwave synthesis of magnesium aluminate spinel oxide for production of highly transparent films by hot compression

Magnesium aluminate spinel oxides have been prepared via poly(N-isopropylacrylamide) assisted microwave technique. The prepared MgAl₂O₄ powders showed a crystalline cubic structure with spinel phase after calcination at 600 °C only. The poly(N-isopropylacrylamide) amount showed a high effect on the crystallite size and the densification behavior of MgAl₂O₄. The increase of the amount of poly(N-isopropylacrylamide) reduced the sintering temperature of MgAl₂O₄ from 1400 °C to 1050 °C. The hot-pressed of MgAl₂O₄ powders in the presence of 3 wt% of poly(N-isopropylacrylamide) exhibited a full density at sintering temperature 1100 °C in 15 min only. The sintered films showed high transparency (81 ± 2%) in the wavelength range 500–1000 nm.     

Role of CeO2–ZrO2 in diesel soot oxidation and thermal stability of potassium catalyst

Potassium nitrate catalysts supported on different oxides (CeO₂, Ce_0.5Zr_0.5O₂ and ZrO₂) were prepared for diesel soot combustion. The ageing treatment was performed at 800 °C for 24 h and the catalytic activity was evaluated by a temperature-programmed oxidation technique. The results demonstrated that, compared with CeO₂ and ZrO₂, Ce_0.5Zr_0.5O₂ presented good redox properties, a high surface area and available potassium-holding capacity at an elevated temperature. For aged K/Ce_0.5Zr_0.5O₂, the combustion temperature of soot particle was 359 °C under tight contact conditions and 455 °C under loose contact conditions. Thus, ceria–zirconia mixed oxides were considered as good candidate supports for diesel soot oxidation catalysis.