Design theory of long-distance WDM dispersion-managed transmissionsystem

This paper describes a novel design theory of long distance wavelength division multiplexed (WDM) dispersion-managed optical transmission systems. Assuming that the transmission distance, bit rate, and number of WDM channels are initially known, we investigate the optimum dispersion allocation and input power per channel to achieve the minimum channel spacing. Based on the design guidelines for single-channel and multichannel systems, we establish the optimal design strategy. Details of the design procedure are demonstrated for 2.5-, 5-, and 10-Gb/s 10000 km WDM systems by using computer simulations. Next, we study the impact of the fiber dispersion slope on the usable wavelength span, and show that the attainable capacity of the representative 5-Gb/s 10000 km WDM system employing the postcompensation scheme can not exceed 100 Gb/s. Finally, we propose several techniques to approach the ultimate capacity of the WDM system and show that up to 1 Tb/s (200×5 Gb/s) 10000 km system can be implemented without utilizing the in-line dispersion slope compensation scheme. We also discuss the 10 Gb/s-10000 km WDM system employing in-line dispersion slope compensation     

Transoceanic WDM System with More Than 100 Gb/s Capacity

This paper reviews several key technologies to realize a transoceanic wavelength-division-multiplexing (WDM) system with more than 100 Gb/s capacity. The key technologies include a novel gain equalization scheme, a broadband erbium-doped fiber amplifier, a chromatic dispersion compensation technique at a transmitter, and a RZ modulation format. Employing these new technologies, we successfully demonstrated a 32 channel 5.3 Gb/s (total capacity of 170 Gb/s) WDM signal transmission over 9879 km.     

利用啁啾光纤光栅实现10Gb/s WDM系统色散补偿

利用二次曝光法制作的啁啾光纤光栅在国内首次邮１０Ｇｂ／ｓｅ ＷＤＭ系统单路色散补偿,经１８０ｋｍ传输后色散补偿的功率代价为１ｄＢ。     

Transmission of Wavelength-Division-Multiplexed Channels With Coherent Optical OFDM

Transmission performance for wavelength-division-multiplexed (WDM) systems with coherent optical orthogonal frequency-division multiplexing is simulated including the fiber nonlinearity effect. The simulation shows that the system Q of the WDM channels at 10 Gb/s is over 13.0 dB for a transmission up to 4800 km of standard single-mode fiber without dispersion compensation     

1.6 Tbit/s(40×40 Gbit/s)光通信传输系统

在国家自然科学基金网(NSFCNet)上已实现由400 km×10 Gbit/s传输链路直接升级的一路400 km×40 Gbit/s光传输实验的基础上,采用自行研制的40×40 Gbit/s载波抑制归零(CS-RZ)码多波长光发送源,进行了160 km的1.6 Tbit/s(40×40 Gbit/s)波分复用(WDM)光传输实验。实验结果表明,对于常规中短距离10 Gbit/s传输链路可以直接升级至40 Gbit/s。但是由于40 Gbit/s传输系统的色散容限小于60 ps/nm,而且传输光纤与色散补偿模块的色散斜率不匹配,要实现40通道40 Gbit/s的传输,必须对40个信道分别进行精细的色散补偿。这也说明,对于宽带的40 Gbit/s多波长系统,有必要优化设计或更新传输链路。     

Chromatic dispersion compensation in coherent opticalcommunications

Chromatic dispersion compensation techniques in coherent transmission systems are reviewed and discussed for potential feasibility. The key compensation device is the wideband delay equalizer. It is shown that stripline-type delay equalizers have the potential for compensating distortion up to 10 Gb/s using a conventional 1.3-μm zero-dispersion single-mode fiber at 1.5 μm. Chromatic dispersion is successfully compensated with a stripline delay for CPFSK transmission at 4 and 6 Gb/s over 200 km of 1.3-μm zero-dispersion single-mode fiber at 1.55 μm. The bandwidth requirement of the compensation techniques for heterodyne detection is more than 10 GHz. However, it is difficult to realize such broadband receivers. Therefore, phase diversity detection with dispersion compensation is a promising scheme     

Chromatic-dispersion compensator using virtually imaged phasedarray

A new method for chromatic-dispersion compensation is proposed and demonstrated. This method can produce a chromatic dispersion practically in a wide range from -2000 to +2000 ps/nm and can compensate simultaneously for the dispersion of over 60 wavelength channels with 100-GHz spacing in a wavelength-division multiplexed (WDM) system that has a total bandwidth of over 50 nm. This method has further attractive features such as very small polarization-state dependence, mechanically variable chromatic dispersion, and potential for small packaging. It was experimentally confirmed that this method compensated for the chromatic dispersion accumulated through 110 km standard single-mode fiber (SMF) at 1.55-μm wavelength and that 10-Gb/s signal quality was clearly recovered after the 110-km transmission     

Transmission of 112 Gb/s dual-carrier DQPSK signal over 10 Gb/s-based WDM optical links

The 112 Gb/s dual-carrier differential quadrature phase shift keying (DC-DQPSK) optical transceiver, which does not need digital signal processing and coherent detection, is proposed for cost-effective 100G transport solution. In this paper, we describe upgrade schemes of 10 Gb/s-based WDM optical links by adopting 112 Gb/s DC-DQPSK transceiver, while the dispersion of the optical links is compensated 100% at each span. Method of introducing the DC-DQPSK signal into single grid of 100 GHz spaced WDM link is demonstrated. Performance sufficient for error-free operation after forward error correction is achieved over 640 km standard single mode fiber (SSMF) link. In another method, we experimentally investigate the transmission performance with co-propagating 10.7 Gb/s on-off-keying (OOK) signals over 1000 km of SSMF when the dual carriers occupy two channel grids separately. Excellent tolerance to the nonlinearities impacted by the OOK signals and low optical signal-to-noise ratio requirement are verified to demonstrate superior transmission performance in 10 Gb/s-based WDM links.     

All-Raman ultralong-haul single-wideband DWDM transmission systems with OADM capability

In this paper, we present a comprehensive experimental investigation of an all-Raman ultrawide single-band transmission system for both 10 and 40 Gb/s line rates. Enabling technologies include forward-Raman pumping of the transmission fiber, counter-Raman pumping of the fiber spans and dispersion compensation modules, wideband dispersion, and dispersion-slope compensation, and modulation formats resistant to both linear and nonlinear impairments. Ultralong-haul (ULH) 128/spl times/10 Gb/s return-to-zero (RZ) and ultrahigh-capacity (UHC) 64/spl times/40 Gb/s carrier-suppressed (CS) RZ transmission are demonstrated for commercially deployed fiber types, including both standard single-mode fiber (SSMF) and nonzero dispersion shifted fibers (NZDSF). The span losses of 23 dB (NZDSF) and 20 dB (SSMF) are consistent with those encountered in terrestrial networks. The optical reaches for 10 Gb/s rate are 4000 km (NZDSF) and 3200 km (SSMF). Using the same distributed Raman amplification (DRA) scheme, UHC over 2.5 Tb/s at a 40-Gb/s per channel rate is also demonstrated for all of the tested fiber types and for optical reaches exceeding 1300 km. We then study the impact of including optical add/drop modules (OADMs) in the transmission system for both 10 and 40 Gb/s channel rates. System performance is characterized by the system margin and the transmission penalty. For all of the experiments shown in this paper, industrial margins and small transmission penalties consistent with operation in commercially deployable networks are demonstrated, showing the feasibility of practical implementation of all-Raman amplified systems for ULH and UHC optical backbones. Attractive features of single-wideband transmission enabled by DRA include simplicity of design, flexible gain and gain-ripple control, good noise performance, and a small system footprint.     

40Gb／s波分系统设备技术

随着40Gb／s端口路由器的出现,未来几年内40Gb／s波分系统设备将取代现有的10Gb／s波分系统设备,就像前几年10Gb／s波分系统设备取代2．5Gb／s波分系统设备一样。然而,40Gb／s波分系统有很多传输限制因素,包括光放大器自发辐射噪声、光纤非线性效应、色散、偏振模色散等等。为实现40Gb／s的波分传输,采取新型调制码型、可调色散补偿、偏振模色散补偿等措施至关重要。     

40-Gb/s WDM transmission with virtually imaged phased array (VIPA) variable dispersion compensators

We have demonstrated variable dispersion compensation by using a virtually imaged phased array (VIPA) to overcome the small dispersion tolerance in 40-Gb/s dense wavelength-division multiplexing (WDM) transmission systems. By utilizing the periodical characteristics of VIPA compensators, we performed simultaneous dispersion compensation in a 1.28-Tb/s (40-Gb/s/spl times/32 ch; C band) short-haul transmission and confirmed that only two VIPA compensators and one fixed dispersion-compensating fiber are required for a large transmission range of 80 km. This performance can greatly reduce the cost, size, and number of compensator menus in a 40-Gb/s WDM short-haul transmission system. In addition, we achieved 3.5-Tb/s (43-Gb/s/spl times/88 ch; C and L bands) transmission over a 600-km nonzero dispersion-shifted fiber by using VIPA compensators. Although channel-by-channel dispersion compensation is required due to the larger residual dispersion slope in long-haul transmission, the periodical characteristics of the VIPA compensators offer the advantage of considerably reducing the number of different modules required to cover the whole C (or L) band. An adequate optical signal-to-noise ratio, which was the same for all channels, was-obtained by using distributed Raman amplification, a gain equalizer, and a preemphasis technique. We achieved a Q-factor of more than 11.8 dB; (BER<10/sup -17/ with forward-error correction) for all 88 channels.     

对40 Gb/s OTDM系统中光纤光栅色散补偿器进行偏振模色散补偿的研究

改变光纤光栅紫外曝光系统 ,在相位掩模板后插入一个旋转装置 ,使得光纤在制作过程中可以进行某种旋转。通过这种方法制作的光纤光栅偏振模色散减小到平均差分群时延 (DGD)约为 0 2ps,而没加旋转制作的光纤光栅平均DGD约为 18 2 ps。采用两个这种低偏振模色散 (PMD)的光纤布拉格光栅 (FBG) ,成功地在 4 0Gb/s光时分复用 (OTDM)系统中补偿了约 2 0 4 0 ps的色散 ,该系统在经过 12 2km普通单模光纤传输后 ,未发现PMD的影响 ,传输功率代价小于 1 4dB。     

Repeaterless 10.7-Gb/s DPSK Transmission Over 304 km of SSMF Using a Coherent Receiver and Electronic Dispersion Compensation

Record repeaterless transmission of differential phase-shift keying (DPSK) at 10.7 Gb/s over 304 km of standard single-mode fiber (SSMF) is demonstrated using a coherent optical receiver and electronic dispersion compensation. This is the longest repeaterless 10-Gb/s transmission over SSMF in the absence of Raman amplifiers. The high receiver sensitivity and the high tolerance to nonlinearities of DPSK allow us to overcome a total link loss of 58 dB with a 3-dB system margin. Coherent detection enables linear electrical dispersion compensation and avoids the use of optical dispersion compensation.     

Application of super-DWDM technologies to terrestrial terabit transmission systems

This paper describes application areas, elemental technologies, and the feasibility of terrestrial terabit wavelength division multiplexing (WDM) transmission systems based on super-dense wavelength division multiplexing (DWDM) technologies with a channel spacing of 12.5 GHz. Numerical simulation results quantitatively show that the merit of super-DWDM transmission is the elimination of the need for dispersion compensation over the several hundreds of kilometers of standard single-mode fiber (SMF). To support super-DWDM transmission, the prototype of a multiwavelength generator, which consists of just an intensity modulator and a phase modulator, is developed as a small-size WDM light source with high-wavelength stability. We use this prototype to conduct a 1.28-Tb/s (512 channels /spl times/ 2.5 Gb/s) transmission experiment with a channel spacing of 12.5 GHz over 320 km (80 km /spl times/ 4 span) of standard SMF without dispersion compensation. The potential and the feasibility of super-DWDM transmission with a channel spacing of 12.5 GHz for terrestrial systems is confirmed by the numerical simulation and the transmission experiment.     

Large PMD Compensated by Four Free Degrees in OTDM System

By introducing a two-stage polarization mode dispersion (PMD) compensator after a optical fiber link with a large PMD,over 270 ps first-order and 2 000 ps2 high-order PMD was compensated. The results show that the two-stage compensator can be used to PMD compensation in the 20 Gb/s optical time division multiplexing system with 60 km high PMD fiber. After compensating, the 270 ps DGD is changed into max. 7 ps. Moreover,the tunable FBG has a function of dispersion compensation.     

WDM-POLSK Transmission Systems by Using Semiconductor Optical Amplifiers

The authors demonstrate the potential of using POLarization Shift Keying (POLSK) modulation format combined with semiconductor optical amplifiers (SOAs) in wavelength division multiplexing (WDM) transmission systems. The constant intensity of the POLSK modulation format allows for substantial removal of cross-gain-modulation impairments in SOAs so that practical amplifier spacing values (more than 100 km) are demonstrated in various different experimental configurations. Record WDM transmission experiments at 10 Gb/s by using SOA-based amplification are presented in short and medium reach system architectures using either single mode fiber or nonzero dispersion shifted fiber     

2R regeneration based on dispersion-imbalanced loop mirror and its applications in WDM systems

2R regeneration based on dispersion-imbalanced loop mirror is investigated including the characteristics of transfer function, output extinction ratio, initial chirp, predispersion, and WDM signals transfer functions. Theoretical results show that the input peak power is a critical parameter for the dispersion-imbalanced loop mirror (DILM) and furthermore, to guarantee the multiwavelength operation of the DILM, limitations due to accumulated dispersion and dispersion slope have to be considered. Our experiment demonstrates that 6/spl times/10 Gb/s WDM signals can be successfully regenerated by a novel 2R regenerator based on a DILM consisting of a single mode fiber (SMF) and a highly nonlinear dispersion-shifted fiber (DSF) after WDM transmission over 40 km SMF of the WDM signals.     

Long-haul WDM transmission using higher order fiber dispersionmanagement

We propose a fiber dispersion management scheme for large-capacity long-haul wavelength division multiplexing (WDM) transmission systems that considers not only second- but also third-order dispersion characteristics using transmission fibers with opposite dispersion signs. It eliminates the waveform distortion of WDM signals that originates from the existence of third-order dispersion, which is a constraint placed on WDM capacity in conventional dispersion management, while reducing the interchannel interaction caused by the interplay of fiber nonlinearity and second-order dispersion. Design concept of the scheme is discussed to show the feasibility of using actual fiber parameters. An experimental investigation on transmission performance regarding the signal pulse format, nonreturn-to-zero (NRZ) and return-to-zero (RZ), and interchannel interaction caused by four-wave mixing (FWM) and cross-phase modulation (XPM) is described for optimizing WDM system performance. It is experimentally shown that RZ pulse transmission is possible without significant spectral broadening over a wide wavelength range in dispersion managed fiber spans. Using these results together with a wideband optical amplifier gain-bandwidth management technique, yields long-distance WDM transmission with the capacity of 25×10 Gb/s over 9288 km     

Key technologies for terabit/second WDM systems with high spectralefficiency of over 1 bit/s/Hz

To fully utilize a limited gain bandwidth of about 35 nm (4.4 THz) in an erbium-doped fiber amplifier, an increase in signal spectral efficiency is required. In this paper, we investigate the key technologies to achieve terabit/second wavelength-division multiplexing (WDM) systems with over 1 bit/s/Hz spectral efficiency. Optical duobinary signals, which have narrower optical spectra than conventional intensity modulation signals, were applied to such dense WDM systems. The measured minimum channel spacing for 20-Gbit/s optical duobinary signals was 32 GHz and a spectral efficiency of over 0.6 bit/s/Hz was reached. By using polarization interleave multiplexing, spectral efficiency was expected to reach 1.2 bit/s/Hz in an ideal case with no polarization dependencies along the transmission lines. In such ultradense WDM systems with narrower channel spacing, stabilizing the wavelengths of laser diodes is an important issue for achieving stable operation over long periods. To do this, we developed a simple and flexible wavelength stabilization system which uses a multiwavelength meter. The wavelengths for 116 channels with 35-GHz spacing were stabilized within ±150 MHz. The stabilization system is applicable to ultradense WDM signals with a spectral efficiency of over 1 bit/s/Hz by employing wavelength interleave multiplexing and an optical selector switch. On the basis of these investigations, we demonstrated a 2.6-Tbit/s (20 Gbit/s×132 channels) WDM transmission by using optical duobinary signals. In addition, 1.28-Tbit/s (20 Gbit/s×64 channels) WDM transmission with a high spectral efficiency of 1 bit/s/Hz was achieved by using polarization interleave multiplexing     

Complete dispersion compensation for 400-fs pulse transmission over10-km fiber link using dispersion compensating fiber and spectral phaseequalizer

We have demonstrated essentially complete dispersion compensation for 400-fs pulses over a 10-km fiber link using dispersion compensating fiber and a programmable femtosecond pulse shaper functioning as a spectral phase equalizer. The pulse shaper impresses adjustable quadratic and cubic phases onto the spectrum and removes all the residual dispersion and dispersion slope in the dispersion compensated fiber link. Our work shows that the pulse shaper technique provides a powerful and convenient tool for programmable fiber dispersion compensation over broad optical bandwidth. This allows distortion-free femtosecond pulse transmission over a fiber link in excess of 10 km without requiring the exact trimming of the dispersion-compensating fiber