All-Inorganic CsPbI3 Quantum Dot Solar Cells with Efficiency over 16% by Defect Control

All-inorganic CsPbI₃ quantum dots (QDs) have shown great potential in photovoltaic applications. However, their performance has been limited by defects and phase stability. Herein, an anion/cation synergy strategy to improve the structural stability of CsPbI₃ QDs and reduce the pivotal iodine vacancy (V_I) defect states is proposed. The Zn-doped CsPbI₃ (Zn:CsPbI₃) QDs have been successfully synthesized employing ZnI₂ as the dopant to provide Zn²⁺ and extra I⁻. Theoretical calculations and experimental results demonstrate that the Zn:CsPbI₃ QDs show better thermodynamic stability and higher photoluminescence quantum yield (PLQY) compared to the pristine CsPbI₃ QDs. The doping of Zn in CsPbI₃ QDs increases the formation energy and Goldschmidt tolerance factor, thereby improving the thermodynamic stability. The additional I⁻ helps to reduce the V_I defects during the synthesis of CsPbI₃ QDs, resulting in the higher PLQY. More importantly, the synergistic effect of Zn²⁺ and I⁻ in CsPbI₃ QDs can prevent the iodine loss during the fabrication of CsPbI₃ QD film, inhibiting the formation of new V_I defect states in the construction of solar cells. Consequently, the anion/cation synergy strategy affords the CsPbI₃ quantum dot solar cells (QDSC) a power conversion efficiency over 16%, which is among the best efficiencies for perovskite QDSCs.     

Solution-Mediated Hybrid FAPbI3 Perovskite Quantum Dots for Over 15% Efficient Solar Cell

Organic–inorganic formamidinium lead triiodide (FAPbI₃) hybrid perovskite quantum dot (QD) is of great interest to photovoltaic (PV) community due to its narrow band gap, higher ambient stability, and long carrier lifetime. However, the surface ligand management of FAPbI₃ QD is still a key hurdle that impedes the design of high-efficiency solar cells. Herein, this study first develops a solution-mediated ligand exchange (SMLE) for preparing FAPbI₃ QD film with enhanced electronic coupling. By dissolving optimal methylammonium iodide (MAI) into antisolvent to treat the FAPbI₃ QD solution, the SMLE can not only effectively replace the long-chain ligands, but also passivate the A- and X-site vacancies. By combining experimental and theoretical results, this study demonstrates that the SMLE engineered FAPbI₃ QD exhibits lower defect density, which is beneficial for fabricating high-quality QD arrays with desired morphology and carrier transport. Consequently, the SMLE FAPbI₃ QD based solar cell outputs a champion efficiency of 15.10% together with improved long-term ambient storage stability, which is currently the highest reported value for hybrid perovskite QD solar cells. These results would provide new design principle of hybrid perovskite QDs toward high-performance optoelectronic application.     

Spray‐Coated Colloidal Perovskite Quantum Dot Films for Highly Efficient Solar Cells

A fully automated spray‐coated technology with ultrathin‐film purification is exploited for the commercial large‐scale solution‐based processing of colloidal inorganic perovskite CsPbI₃ quantum dot (QD) films toward solar cells. This process is in the air outside the glove box. To further improve the performance of QD solar cells, the short‐chain ligand of phenyltrimethylammonium bromide (PTABr) with a benzene group is introduced to partially substitute for the original long‐chain ligands of the colloidal QD surface (namely PTABr‐CsPbI₃). This process not only enhances the carrier charge mobility within the QD film due to shortening length between adjacent QDs, but also passivates the halide vacancy defects of QD by Br^? from PTABr. The colloidal QD solar cells show a power conversion efficiency (PCE) of 11.2% with an open voltage of 1.11 V, a short current density of 14.4 mA cm^?2, and a fill factor of 0.70. Due to the hydrophobic surface chemistry of the PTABr–CsPbI₃ film, the solar cell can maintain 80% of the initial PCE in ambient conditions for one month without any encapsulation. Such a low‐cost and efficient spray‐coating technology also offers an avenue to the film fabrication of colloidal nanocrystals for electronic devices.     

Realistic Detailed Balance Study of the Quantum Efficiency of Quantum Dot Solar Cells

An attractive but challenging technology for high efficiency solar energy conversion is the intermediate band solar cell (IBSC), whose theoretical efficiency limit is 63%, yet which has so far failed to yield high efficiencies in practice. The most advanced IBSC technology is that based on quantum dots (QDs): the QD‐IBSC. In this paper, k·p calculations of photon absorption in the QDs are combined with a multi‐level detailed balance model. The model has been used to reproduce the measured quantum efficiency of a real QD‐IBSC and its temperature dependence. This allows the analysis of individual sub‐bandgap transition currents, which has as yet not been possible experimentally, yielding a deeper understanding of the failure of current QD‐IBSCs. Based on the agreement with experimental data, the model is believed to be realistic enough to evaluate future QD‐IBSC proposals.     

Efficiency Enhanced Hybrid Solar Cells Using a Blend of Quantum Dots and Nanorods

The cell performance of organic‐inorganic hybrid photovoltaic devices based on CdSe nanocrystals and the semiconducting polymer poly[2,6‐(4,4‐bis(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b′]‐dithiophene)‐alt‐4,7‐(2,1,3‐benzothiadiazole)] (PCPDTBT) is strongly dependent on the applied polymer‐to‐nanocrystal loading ratio and the annealing temperature. It is shown here that higher temperatures for the thermal annealing step have a beneficial impact on the nanocrystal phase by forming extended agglomerates necessary for electron percolation to enhance the short‐circuit current. However, there is a concomitant reduction of the open‐circuit voltage, which arises from energy‐level alterations of the organic and the inorganic component. Based on quantum dots and PCPDTBT, we present an optimized organic–inorganic hybrid system utilizing an annealing temperature of 210 °C, which provides a maximum power conversion efficiency of 2.8%. Further improvement is obtained by blending nanocrystals of two different shapes to compose a favorable n‐type network. The blend of spherical quantum dots and elongated nanorods results in a well‐interconnected pathway for electrons within the p‐type polmer matrix, yielding maximum efficiencies of 3.6% under simulated AM 1.5 illumination.     

Multiple Function Synchronous Optimization by PbS Quantum Dots for Highly Stable Planar Perovskite Solar Cells with Efficiency Exceeding 23%

Colloidal lead sulfide (PbS) quantum dots (QDs), which possess quantum confinement effect and processing compatibility with perovskite, are regarded as an excellent material for optimizing perovskite solar cells (PSCs). However, the existing PSCs optimized by PbS QDs are still facing the challenges of poor performance of the charge transport layers, low utilization in the near-infrared (NIR) region, and unsuitable energy level alignment, which limit the improvement of power conversion efficiency (PCE). Herein, a synchronous optimization strategy is realized via simultaneously introducing PbS QDs into SnO₂ electron transport layer and employing rare-earth-doped PbS QDs (Eu:PbS QDs) film with hydrophobic chain ligands as the NIR light-absorping layer and hole transport layer (HTL) of devices. PbS QDs effectively decrease the density of trap states by passivating defects. Eu:PbS QDs film with adjustable bandgap is employed as an absorption layer to broaden the NIR spectral absorption. The well-matched energy level between Eu:PbS QDs layer and perovskite layer implies efficient hole transfer at the interface. The successful synchronous optimization greatly elevates all photovoltaic parameters, reaching a maximum PCE of 23.27%. This PCE is the highest for PSCs utilizing PbS QDs material in recent years. The optimized PSCs retain long-term moisture and light stability.     

Constructing All-Inorganic Perovskite/Fluoride Nanocomposites for Efficient and Ultra-Stable Perovskite Solar Cells

Organic-inorganic hybrid perovskite solar cells (PSCs) have rapidly developed over the past decade and have achieved the latest certified power conversion efficiency (PCE) up to 25.5%. However, unsatisfactory long-term operational stability for these hybrid PSCs remains a huge obstacle to further development and commercialization. Herein, a unique hetero-structured CsPbI₃/CaF₂ perovskite/fluoride nanocomposites (PFNCs) is fabricated via a newly developed facile two-step hetero-epitaxial growth strategy to deliver efficient and ultra-stable PSCs. After being incorporated into the crystal lattice of α-phase CsPbI₃ perovskite, the cubic-phase CaF₂ in the resultant CsPbI₃/CaF₂ PFNCs can not only passivate the intrinsic defects of CsPbI₃ perovskite itself but also effectively suppress the notorious ion migration in hybrid perovskite Cs_0.05FA_0.81MA_0.14PbI_2.55Br_0.45 (CsFAMA) thin-films of PSCs. As such, the CsFAMA PSC devices based on CsPbI₃/CaF₂-deposited perovskite thin-film achieve a mean PCE of 20.45%, in sharp contrast to 19.33% of the control devices without deposition. Specifically, the CsPbI₃/CaF₂-deposited PSC retains 85% of its original PCE after 1000 h continuous operation at the maximum power point under AM 1.5G solar light, far better than those of the control and CsPbI₃-deposited PSCs with a device T₈₅ lifetime of 315 and 125 h, respectively.     

In-Situ Hot Oxygen Cleansing and Passivation for All-Inorganic Perovskite Solar Cells Deposited in Ambient to Breakthrough 19% Efficiency

All-inorganic perovskite CsPbI₃ has attracted extensive attention recently because of its excellent thermal and chemical stability. However, its photovoltaic performance is hindered by large energy losses (E_loss) due to the presence of point defects. In addition, hydroiodic acid (HI) is currently employed as a hydrolysis-derived precursor of intermediate compounds, which often leads to a small amount of organic residue, thus undermining its chemical stability. Herein, an in-situ hot oxygen cleansing with superior passivation (HOCP) for the triple halide-mixed CsPb(I_2.85Br_0.149Cl_0.001) perovskite solar cells (abbreviated as CsPbTh₃) deposited in an ambient atmosphere to reduce the E_loss to as low as 0.48 eV for the power conversion efficiency (PCE) to reach 19.65% is demonstrated. It is found that the hot oxygen treatment effectively removes the organic residues. Meanwhile, it passivates halide vacancies, hence reduces the trap states and nonradiative recombination losses within the perovskite layer. As a result, the PCE is increased significantly from 17.15% to 19.65% under 1 sun illumination with an open-circuit voltage enlarged to 1.23 from 1.14 V, which corresponds to an E_loss reduction from 0.57 to 0.48 eV. Also, the HOCP-treated devices exhibit better long-term stability. This insight should pave a way for decreasing nonradiative charge recombination losses for high-performance inorganic perovskite photoelectronics.     

All Slot-Die Coated Non-Fullerene Organic Solar Cells with PCE 11%

Slot-die (SD) coating is used to fabricate fully solution processed organic solar cells (OSCs) based on a blend of high performance donor polymer (PTB7-Th) and a non-fullerene acceptor (IEICO-4F) for stable devices over extended periods of operation. The optimization of a sequential deposition process of transport and active layers, under ambient conditions, enable high efficiency slot-die coated solar cells with remarkable power conversion efficiencies (PCE) > 11.0% to bridge the gap between lab-to-fab. Fully slot-die coated inverted OSCs are demonstrated with efficiencies reaching 11% along with 1 cm² devices, proving the scalability and reproducibility of the proposed technique. Further, replacing the evaporated Ag electrode with solution processed Ag nanowire (AgNW) electrodes shows the highest light utilization efficiency of 5.26% for semi-transparent OSC with a PCE of 9.07% and average visible transmission of 58%.     

Surface Passivation with Diaminopropane Dihydroiodide for p-i-n Perovskite Solar Cells with Over 25% Efficiency

At present, one of the major factors limiting the further improvement of inverted (p-i-n) perovskite solar cells (PSCs) is trap-assisted non-radiative recombination at the perovskite/electron transporting layer (ETL) interface. Surface passivation with organic ammonium salt is a powerful strategy to improve the performance of PSCs. Herein, an effective method by using propylamine hydroiodide (PAI) and 1,3-diaminopropane dihydroiodide (PDADI) is reported to modify the perovskite/ETL interface. These two ammonium salts do not form new perovskite but directly passivate the defects on the perovskite surface after annealing. The results show that the PDADI-modified perovskite films possess a lower surface defect density and less non-radiative recombination as well as improved charge carrier transport. Based on this strategy, the PDADI-modified p-i-n PSCs deliver an impressive efficiency of 25.09% (certified 24.58%) with an open-circuit voltage of 1.184 V. Furthermore, the unencapsulated PDADI-modified PSCs also exhibit good storage stability, retaining 91% of initial PCE at 65 °C in a N₂ glove box for 1300 h. This strategy provides an efficient route to fabricate highly efficient and stable inverted p-i-n structured PSCs.     

Pre-Buried ETL with Bottom-Up Strategy Toward Flexible Perovskite Solar Cells with Efficiency Over 23%

With rapid development of photovoltaic technology, flexible perovskite solar cells (f-PSCs) have attracted much attention for their light weight, high flexibility and portability. However, the power conversion efficiency (PCE) achieved so far is not yet comparable to that of rigid devices. This is mainly due to the great challenge of depositing homogeneous and high-quality perovskite films on flexible substrate. In this study, the pre-buried 3-aminopropionic acid hydroiodide (3AAH) additives into the electron transport layer (ETL) and modified the ETL/perovskite (PVK) interface by a bottom-up strategy. 3AAH treatment induced a templated perovskite grain growth and improved the quality of the ETL. By this, the residual stresses generated in PVK during the annealing-cooling process are released and converted into micro-compressive stresses. As a result, the defect density of f-PSCs with pre-buried 3AAH is reduced and the photovoltaic performance is greatly improved, reaching an exceptional PCE of 23.36%. This strategy provides a new idea to bridge the gap between flexible and rigid devices.     

Precursor Engineering for All‐Inorganic CsPbI2Br Perovskite Solar Cells with 14.78% Efficiency

The optoelectronic properties of perovskite films are closely related to the film quality, so depositing dense, uniform, and stable perovskite films is crucial for fabricating high‐performance perovskite solar cells (PSCs). CsPbI₂Br perovskite, prized for its superb stability toward light soaking and thermal aging, has received a great deal of attention recently. However, the air instability and poor performance of CsPbI₂Br PSCs are hindering its further progress. Here, an approach is reported for depositing high‐quality CsPbI₂Br films via the Lewis base adducts PbI₂(DMSO) and PbBr₂(DMSO) as precursors to slow the crystallization of the perovskite film. This process produces CsPbI₂Br films with large‐scale crystalline grains, flat surfaces, low defects, and long carrier lifetimes. More interestingly, PbI₂(DMSO) and PbBr₂(DMSO) adducts could significantly improve the stability of CsPbI₂Br films in air. Using films prepared by this technique, a power conversion efficiency (PCE) of 14.78% is obtained in CsPbI₂Br PSCs, which is the highest PCE value reported for CsPbI₂Br‐based PSCs to date. In addition, the PSCs based on DMSO adducts show an extended operational lifetime in air. These excellent performances indicate that preparing high‐quality inorganic perovskite films by using DMSO adducts will be a potential method for improving the performance of other inorganic PSCs.     

Highly-Stable CsPbI3 Perovskite Solar Cells with an Efficiency of 21.11% via Fluorinated 4-Amino-Benzoate Cesium Bifacial Passivation

The poor interface quality between cesium lead triiodide (CsPbI₃) perovskite and the electron transport layer limits the stability and efficiency of CsPbI₃ perovskite solar cells (PSCs). Herein, a 4-amino-2,3,5,6-tetrafluorobenzoate cesium (ATFC) is designed as a bifacial defect passivator to tailor the perovskite/TiO₂ interface. The comprehensive experiments demonstrate that ATFC can not only optimize the conductivity, electron mobility, and energy band structure of the TiO₂ layer by passivation of the undercoordinated Ti⁴⁺, oxygen vacancy (V_O), and free  OH defects but also promote the yield of high-quality CsPbI₃ film by synergistic passivation of undercoordinated Pb²⁺ defects with the  CO group and F atom, and limiting I⁻ migration via F···I interaction. Benefiting from the above interactions, the ATFC-modified CsPbI₃ device yields a champion power conversion efficiency (PCE) of 21.11% and an excellent open-circuit voltage (V_OC) of 1.24 V. Meanwhile, the optimized CsPbI₃ PSC maintains 92.74% of its initial efficiency after aging 800 h in air atmosphere, and has almost no efficiency attenuation after tracking at maximum power point for 350 h.     

High-Efficiency Perovskite Quantum Dot Photovoltaic with Homogeneous Structure and Energy Landscape

The energy disorder originating from quantum dot (QD) size and relevant solid film inhomogeneity is detrimental to the charge transport and efficiency of QD based solar cells. The emergence of halide perovskite QDs (PQDs) have attracted great attention as promising absorbers in QD photovoltaics. However, it is currently difficult in preparing structural uniform PQD film with homogenous energetic landscape, which is essential for highly reproducible and efficient solar cells. Herein, assisted by a bidentate ligand 2,5-thiophenedicarboxylic acid, a facile solution phase anchoring (SPA) strategy is first reported for design and preparation of all-inorganic CsPbI₃ PQD film with reduced structure and energy disorder. The SPA can enhance PQD dispersion as well as dot-to-dot interaction, which is beneficial for fabricating high-quality PQD arrays and photovoltaic devices. The engineered CsPbI₃ PQD solar cell exhibits enhanced reproducibility, and higher open–circuit voltage together with a champion efficiency of 16.14%, which is among the highest report to date. These results are believed to provide design principle of uniform PQDs for high-performance optoelectronic application.     

Dopant-Free Polymer HTM-Based CsPbI2Br Solar Cells with Efficiency Over 17% in Sunlight and 34% in Indoor Light

To abate the issue of moisture-assisted phase transition of CsPbI₂Br, caused by hygroscopic dopants used in the hole-transporting material (HTM), developing dopant-free HTMs is necessary. In this work, a new polymer, PDTDT, is developed as a dopant-free HTM for CsPbI₂Br solar cells, and the device performance and stability are systematically compared with cells employing dopant-free P3HT. CsPbI₂Br solar cells using PDTDT show an efficiency of 17.36% with V_OC of 1.42 V and FF of 81.29%, which is one of the highest values for CsPbI₂Br cells. Moreover, a record-high efficiency of 34.20% with V_OC of 1.14 V under 200 lux indoor light illumination and efficiency of 14.54% (certified efficiency of 13.86%) for a 1 cm² device under one sun are accomplished. Importantly, PDTDT shows superior/comparable device stability to P3HT, promising its potential to be an alternative to popular doped Spiro-OMeTAD and P3HT HTM.     

Design and Synthesis of Fluorinated Quantum Dots for Efficient and Stable 0D/3D Perovskite Solar Cells

Dimensionality engineering involving the low-dimensional and 3D perovskites has been demonstrated as an efficient promising strategy to modulate interfacial energy loss as well as instability in perovskite solar cells (PSCs). Herein, the use of fluorinated Cesium Lead Iodide (CsPbI₃) perovskite quantum dot (PQD) is first reported as interface modification layer for PSCs. The binding between the CsPbI₃ PQD surface and native oleic acid (OLA)/oleylamine (OAm) ligands is governed by a dynamic adsorption–desorption equilibrium. Perfluorooctanoic acid (PFA) with stronger binding affinity and more hydrophobic nature is explored to partially replace OLA to prepare the fluorinated ligand capped CsPbI₃ PQDs (F-CsPbI₃). Through optimization of the addition of PFA during hot-injection synthesis, the in situ treated F-CsPbI₃ PQDs display reduced surface defect states, higher photoluminescence quantum yields together with improved stability. Subsequently, both CsPbI₃ and F-CsPbI₃ PQDs are utilized as interface engineering layer in PSCs, delivering the best efficiency values of 21.99% and 23.42%, respectively, which is significantly enhanced compared to the control device (20.37%). More importantly, benefiting from its more hydrophobic properties, the F-CsPbI₃ PQD treated device exhibits excellent ambient storage stability (25 °C, relative humidity: 35–45%), retaining over 80% of its initial efficiency after 1500 h aging.     

Efficient Perovskite Hybrid Solar Cells via Ionomer Interfacial Engineering

The surface of the solution‐processed methylammonium lead tri‐iodide (CH₃NH₃PbI₃) perovskite layer in perovskite hybrid solar cells (pero‐HSCs) tends to become rough during operation, which inevitably leads to deterioration of the contact between the perovskite layer and the charge‐extraction layers. Moreover, the low electrical conductivity of the electron extraction layer (EEL) gives rises to low electron collection efficiency and severe charge carrier recombination, resulting in energy loss during the charge‐extraction and ‐transport processes, lowering the efficiency of pero‐HSCs. To circumvent these problems, we utilize a solution‐processed ultrathin layer of a ionomer, 4‐lithium styrenesulfonic acid/styrene copolymer (LiSPS), to re‐engineer the interface of CH₃NH₃PbI₃ in planar heterojunction (PHJ) pero‐HSCs. As a result, PHJ pero‐HSCs are achieved with an increased photocurrent density of 20.90 mA cm^?2, an enlarged fill factor of 77.80%, a corresponding enhanced power conversion efficiency of 13.83%, high reproducibility, and low photocurrent hysteresis. Further investigation into the optical and electrical properties and the thin‐film morphologies of CH₃NH₃PbI₃ with and without LiSPS, and the photophysics of the pero‐HSCs with and without LiSPS are shown. These demonstrate that the high performance of the pero‐HSCs incorporated with LiSPS can be attributed to the reduction in both the charge carrier recombination and leakage current, as well as more efficient charge carrier collection, filling of the perforations in CH₃NH₃PbI_3, and a higher electrical conductivity of the LiSPS thin layer. These results demonstrate that our method provides a simple way to boost the efficiency of pero‐HSCs.     

Fluorinated Pentafulvalene-Fused Hole-Transporting Material Enhances the Performance of Perovskite Solar Cells with Efficiency Exceeding 23%

Organic small molecular materials with coplanar π-conjugated system as HTMs in perovskite solar cells (PSCs) have attracted considerable attention due to their high charge transport capability and thermal stability. Herein, three novel pentafulvalene-fused derivatives with or without fluorine atoms incorporated ( YSH-oF and YSH-mF and YSH-H , respectively) are designed, synthesized, and applied as hole-transporting materials (HTMs) in PSCs fabrication. The fluorinated HTMs, YSH-oF and YSH-mF , exhibited higher hole mobility and better charge extraction at the perovskite/HTM interface than non-fluorinated one do, presumably due to the closer intermolecular π–π packing interactions. As a result, small-area (0.09 cm²) PSCs made with YSH-oF and YSH-mF achieved an impressive power conversion efficiency (PCE) of 23.59% and 22.76% respectively, with negligible hysteresis, in contrast with the 20.57% for the YSH-H -based devices. Furthermore, for large-area (1.00 cm²) devices, the PSCs employing YSH-oF exhibited a PCE of 21.92%. Moreover, excellent long-term device stability is demonstrated for PSCs with F-substituted HTMs ( YSH-oF and YSH-mF ), presumably due to the higher hydrophobicity. This study shows the great potential of fluorinated pentafulvalene-fused materials as low-cost HTM for efficient and stable PSCs.     

Spidermen Strategy for Stable 24% Efficiency Perovskite Solar Cells

The interface energetics-modification plays an important role in improving the power conversion efficiency (PCE) among the perovskite solar cells (PSCs). Considering the low carrier mobility caused by defects in PSCs, a double-layer modification engineering strategy is adopted to introduce the “spiderman” NOBF₄ (nitrosonium tetrafluoroborate) between tin dioxide (SnO₂ and perovskite layers. NO⁺, as the interfacial bonding layer, can passivate the oxygen vacancy in SnO₂, while BF₄⁻ can optimize the defects in the bulk of perovskite. This conclusion is confirmed by theoretical calculation and transmission electron microscopy (TEM). The synergistic effect of NO⁺ and BF₄⁻ distinctly heightens the carrier extraction efficiency, and the PCE of PSCs is 24.04% with a fill factor (FF) of 82.98% and long-term stability. This study underlines the effectiveness of multifunctional additives in improving interface contact and enhancing PCE of PSCs.