Morphology and mechanical properties of liquid crystalline copolyester and poly(ethylene 2,6-naphthalate) blends

Blends of poly(ethylene 2,6-naphthalate) (PEN) and a liquid crystalline copolyester (LCP), poly(benzoate-naphthoate), were prepared in a twin-screw extruder. Specimens for mechanical testing were prepared by injection molding. The morphology and mechanical properties were investigated by scanning electron microscopy (SEM) and an Instron tensile tester. SEM studies revealed that finely dispersed spherical domains of the liquid crystalline polymer (LCP) were formed in the PEN matrix, and the inclusions were deformed into fibrils from the spherical droplets with increasing LCP content. The morphology of the blends was found to be affected by their composition and a distinct skin-core morphology was found to develop in the injection molded samples of these blends. Mechanical properties were improved with increasing LCP content, and synergistic effects have been observed at 70 wt% LCP content whereas the elongation at break was found to be reduced drastically above 10 wt% of LCP content. This is a characteristic typical of chopped-fiber-filled composites. The improvement in mechanical properties is likely due to the reinforcement of the PEN matrix by the fibrous LCP phase as observed by scanning electron microscopy. The tensile and modulus mechanical behavior of the LCP/PEN blends was very similar to those of the polymeric composite, and the tensile strength and flexural modulus of the LCP/PEN 70/30 blend were two times the value of PEN homopolymer and exceeded those of pure LCP, suggesting LCP acts as a reinforcing agent in the blends.     

Fiber reinforcement and fracture resistance of PC/PBT/LCP ternary in situ composite

The microstructures, mechanical properties, and fracture toughness of LCP (Vectra B950) reinforced PC/PBT blend with a 60/40 weight ratio have been studied. LCP of varying concentrations were investigated as rigid fillers in matrices of multiphase polymer blends. In this study, differences in microstructures and morphology between samples of two thicknesses (4 mm thick and 6 mm thick) and two geometries (dumbbell and rectangular) were compared using scanning electron microscopy (SEM). Given identical processing conditions, fibrous LCP structures were evident in the 4-mm-thick injection molded, dumbbell-shaped samples, whereas the 6-mm-thick rectangular samples displayed spherical dispersion of LCP aggregates that embrittled the preblended ductile matrix. Tensile properties of the dumbbell specimens showed superior strengthening and stiffening whereby the tensile strength increased twofold and the modulus increased fourfold. Plane strain fracture toughness was slightly enhanced as the LCP content increased because of the fiber strengthening effect but the overall fracture performance of the in situ composites was relatively poor compared with PC/PBT. Experimental results were compared with those predicted in composite theory. Simplified micromechanics equations were developed to describe the tensile moduli of injection molded LCP reinforced blends that exhibited a strong skin-core morphology.     

Blends of a PPO–PS alloy with a liquid crystalline polymer

Blends of a PPO–PS alloy with a liquid crystalline polymer have been studied for their dynamic properties, rheology, mechanical properties, and morphology. This work is an extension of our previous work on PPO/LCP blends. The addition of the LCP to the PPO–PS alloy resulted in a marked reduction in the viscosity of the blends and increased processibility. The dynamic studies showed that the alloy is immiscible and incompatible with the LCP at all concentrations. The tensile properties of the blends showed a drastic increase with the increase in LCP concentration, thus indicating that the LCP acted as a reinforcing agent. The tensile strength, secant modulus, and impact strength of the PPO–PS/LCP blends were significantly higher than that of PPO/LCP blends. Morphology of the injection molded samples of the PPO–PS/LCP blends showed that the in situ formed fibrous LCP phase was preserved in the solidified form. A distinct skin–core morphology was also seen for the blends, particularly with low LCP concentrations. The improvement of the mechanical properties of the blends is attributed to these in situ fibers of LCP embedded in the PPO–PS matrix. The improvement in the properties of PPO–PS/LCP over PPO/LCP is also attributed to the addition of the PS which consolidates the matrix. © 1995 John Wiley & Sons, Inc.     

Effects of processing conditions on the mechanical performance of maleic anhydride compatibilized in-situ composites of polypropylene with liquid crystalline polymer

Maleic anhydride compatibilized blends of isotactic polypropylene (PP) and thermotropic liquid crystaline polymer (LCP) were prepared either by the direct injection molding (one-step process), or by twin-screw extrusion blending, after which specimens were injection molded (two-step process). The morphology and mechanical properties of these injection molded in situ LCP composites were studied by means of scanning electron microscopy (SEM), Izod impact testing, static tensile, and dynamic mechanical measurements. SEM observations showed that fine and elongated LCP fibrils are formed in the maleic anhydride compatibilized in situ composites fabricated by means of the one-step process. The tensile strength and modulus of these composites were considerably close to those predicted from the rule of mixtures. Furthermore, the impact behavior of LCP fibril reinforced composites was similar to that of the glass fiber reinforced polymer composites. On the other hand, the maleic anhydride compatibilized blends prepared from the two-step process showed lower mechanical performance, which was attributed to the poorer processing behavior leading to the degradation of PP. The effects of the processing steps, temperatures, and compatibilizer addition on the mechanical properties of the PP/LCP blends are discussed.     

Characterization of thermotropic liquid crystalline polyester/polysulfone blends

The morphology, rheology, and mechanical properties of blends of polysulfone (PSF) with up to 65% of a wholly aromatic liquid crystalline polymer (LCP) were investigated. In injection molded specimens a skin-core morphology was observed with the LCP minor phase oriented in the skin and globular in the core. Scanning electron microscopy of fractured surfaces showed sharp phase boundaries, suggesting low interfacial adhesion. The neat PSF and blends with low amounts of LCP exhibited a low shear Newtonian plateau not observed in the blends with high LCP levels. The addition of LCP to PSF resulted in an increase in stiffness, a small increase in tensile strength, and a significant improvement in processability.     

A gradient structure formed in injection‐molded polycarbonate in situ hybrid composites and its corresponding performances

Three polycarbonate (PC) composites that were reinforced, respectively, with liquid crystalline polymer (LCP), glass fibers, and both of them were prepared by a single injection‐molding process. The role of LCP in improving the processibility of the composites was characterized by torque measurement test. The transitions of LCP morphology in two‐ and three‐component composites were investigated by using polarizing optical microscopy and scanning electron microscopy. The micrographs showed a skin–core gradient structure in all three systems investigated, and the addition of glass fiber to the PC/LCP blend affected the morphological transition and content distribution of dispersed LCP phase through the thickness of the injection‐molded samples. These results were correlated well with the measurements of tensile mechanical properties and dynamic mechanical analysis. How to fully use the dispersed LCP phase in PC in situ hybrid composites was discussed for the thickness change of core layer and the heterogeneous distribution of more LCP in the core. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 625–634, 2004     

Study on in situ reinforcing and toughening of a semiflexible thermotropic copolyesteramide in PBT/PA66 blends

Ternary in situ composites based on poly(butylene terephthalate) (PBT), polyamide 66 (PA66), and semixflexible liquid crystalline polymer (LCP) were systematically investigated. The LCP used was an ABA30/PET liquid crystalline copolyesteramide based on 30 mol % of p‐aminobenzoic acid (ABA) and 70 mol % of poly(ethylene terephthalate) (PET). The specimens for thermal and rheological measurements were prepared by batch mixing, while samples for mechanical tests were prepared by injection molding. The results showed that the melting temperatures of the PBT and PA66 phases tend to decrease with increasing LCP addition. They also shifted toward each other due to the compatibilization of the LCP. The torque measurements showed that the ternary blends exhibited an apparent maximum near 2.5–5 wt % LCP. Thereafter, the viscosity of the blends decreased dramatically at higher LCP concentrations. Furthermore, the torque curves versus the PA66 composition showed that the binary PBT/PA66 blends can be classified as negative deviation blends (NDBs). The PBT/PA66/LCP blends containing up to 15 wt % LCP were termed as positive deviation blends (PDBs), while the blends with the LCP ≥25 wt % exhibited an NDB behavior. Finally, the tensile tests showed that the stiffness and tensile strength of ternary in situ composites were generally improved with increasing LCP content. The impact strength of ternary composites initially increased by the LCP addition, then deteriorated when the LCP content was higher than 10 wt %. The correlation between the mechanical properties and morphology of the blends is discussed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1975–1988, 2000     

Mechanical properties and morphology of liquid crystalline copolyester-amide and amorphous polyamide blends

Blends of an amorphous polyamide (PA) and a liquid crystalline copolyesteramide (LCP), poly(naphthoate-aminophenoterephthalate) were prepared in a twin-screw extruder. Specimens for mechanical testing were prepared by injection molding. Morphological, thermal, mechanical, and rheological properties were investigated by scanning electron microscopy (SEM), differential scanning calorimetry (DSC), X-ray diffractometry, capillary rheometry, and a tensile tester, respectively. The tensile mechanical behavior of the LCP/PA blends was found to be affected by their compositions and specimen thickness. Tensile testing revealed that the tensile mechanical behavior of the LCP/PA blends was very similar to that of polymeric composite and the tensile strength of the LCP/PA (50/50) blend was approximately two times of the value of PA homopolymer and exceeded that of pure LCP. The morphology of the LCP/PA blends was also found to be affected by their compositions. SEM studies revealed that the liquid crystalline polymer (LCP) formed finely dispersed spherical domains in the PA matrix and the inclusions were deformed into fibrils from the spherical droplets with increasing LCP content. It has been found that droplet and fiber formations lead to low and high strength material, respectively. In particular, at specific LCP content (50 wt%), the tensile strength of the LCP/PA blend exceeded that of pure LCP. The improvement in tensile properties is likely due to the reinforcement of the PA matrix by the fibrous LCP phase as observed by SEM. A distinct shell-core morphology was found to develop in the injection molded samples of these blends. This is believed to have a synergistic effect on the tensile properties of the LCP/PA blends. The rheological behavior of the LCP/PA blends was found to be very different from that of the parent polymers and significant viscosity reductions were observed for the LCP/PA (50/50) blend. Based upon DSC, these blends have shown to be incompatible in the entire range of concentrations.     

Self‐reinforced polypropylene/LCP extruded strands and their moldings

Polypropylenes (PP) of various molecular weights were mixed with a thermotropic liquid crystal polymer (LCP) and strands were prepared by extrusion and stretching. The strands were subsequently pelletized and then injection molded at temperatures below the melting point of LCP. The mechanical properties and the morphology of the strands and injection‐molded specimens were investigated as a function of draw ratio, LCP concentration, and PP molecular weight. The results for strands show that an increase in the draw ratio, LCP concentration and matrix molecular weight in general enhance the modulus and tensile strength. However, the tensile properties of injection‐molded specimens are found to be reduced compared with those of the original strands, in particular at high LCP concentration. The morphology of LCP changes from spherical or ellipsoidal droplets to elongated fibrils in the strands as the draw ratio increases, but this aligned LCP fibrillar morphology was not transferred to the injection‐molded specimens because of the disorientation of fibrils during injection molding. Compatibilization of PP/LCP blends was also studied by using various polymers. Maleic anhydride and acrylic acid modified PPs improved the tensile properties modestly, but maleic anhydride modified EPDM reduced the tensile properties.     

Improved thermal and mechanical properties of poly(butylene succinate) by polymer blending with a thermotropic liquid crystalline polyester

A novel polymer blending system consisting of poly(butylene succinate) (PBS) and a thermotropic liquid crystalline polyester [LCP: a poly(4‐hydroxybenzoate)‐based polymer] was investigated in the presence and absence of a polycarbodiimide (PCD) and/or 1,1′‐carbonyl biscaprolactam (CBC) as chain extenders. Although the LCP was immiscible with PBS, it formed elongated fibrous domains having an orientation in the flowing direction when an extensional flow was applied during the processing. Scanning electron micrograph (SEM) of the injection‐molded polymer blends supported the distribution of micro fibrils of LCP in the PBS matrix by which the efficient toughening was provided. These blend specimens showed highly improved mechanical properties along with retaining high dynamic storage‐moduli (E′) up to the melting temperature of PBS. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39952.     

Compatibilizing effect of styrene–maleic anhydride copolymer on the properties of polyamide‐6/liquid crystalline copolyester composites

Liquid crystalline polymer–polyamide‐6 (LCP/PA6) composites containing 20 wt % LCP content were compatibilized by a random styrene–maleic anhydride copolymer (RSMA). The blending was performed via extrusion followed by injection molding. The LCP employed was a commercial copolyester, Vectra A950. The dynamic mechanical (DMA), rheological, thermal, and mechanical properties as well as the morphology of the composites were studied. The DMA and rheological results showed that RSMA is an effective compatibilizer for LCP/PA6 blends. The mechanical measurements showed that the stiffness, tensile strength, and toughness of the in situ composites are generally improved with increasing RSMA content. However, these mechanical properties deteriorated considerably when RSMA content was above 10 wt %. The drop‐weight dart impact test was also applied to analyze the toughening behavior of these composites. The results show that the maximum impact force (F_max) and crack‐initiation energy (E_init) tend to increase with increasing RSMA content. From these results, it appeared that RSMA prolongs the crack‐initiation time and increases the energies for crack initiation and impact fracture, thereby leading to toughening of LCP/PA6 in situ composites. Finally, the correlation between the mechanical properties and morphology of the blends is discussed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1964–1974, 2000     

Blends containing liquid crystalline polymers: Preparation and properties of melt-drawn fibers,unidirectional prepregs,and composite laminates

This paper discusses the effect of melt drawing on the mechanical properties and morphology of liquid crystalline polymer (LCP) and thermoplastic polymer blends. Extruded fibers and films of LCP/polymer blends were melt drawn to develop uniaxial orientation of the dispersed LCP phase. The longitudinal modulus increased with increasing draw. The increase in modulus was due to higher aspect ratio of the LCP fibrils and improved molecular orientation of the LCP chains within the fibrils. Laminated composites were prepared using the extruded sheets as prepregs. The mechanical properties and the coefficient of thermal expansion (CTE) of the prepreg and the laminates agreed well with predictions from conventional composite lamination theories.     

Electrical conductivity of polymer blends containing liquid crystalline polymer and carbon black

This paper presents results of a study of melt‐processed immiscible polymer blends of high impact polystyrene (HIPS), liquid crystalline polymer (LCP) and carbon black (CB). Relationships between composition, electrical resistivity and morphology of the blends produced by Brabender mixing followed by compression molding, extrusion through a capillary rheometer, extrusion through a single‐screw extruder and injection molding were investigated. The LCP phase morphology in the blends was found sensitive to the processing conditions. A blend composition of at least 20 wt% LCP and 2 phr CB is necessary to preserve the conductivity of filaments produced over a wide range of shear rates. Enhancement of conductivity of blends containing CB and 30 wt% or more LCP was observed, under processing at 270°C and increasing levels of shear rate. An important role of the skin region in determining the resisitivy of injection molded samples was found. A good agreement between resistivity values of extruded or injection molded blends with resistivity values of filaments produced at similar conditions by a capillary rheometer was shown. Hence, the study of shear rate effect on resistivity of capillary rheometer filaments may serve as a predictor of resistivity behavior in real processing procedures. Polym. Eng. Sci. 44:528–540, 2004. © 2004 Society of Plastics Engineers.     

Polymer blends of polyethersulfone with all aromatic liquid crystalline co-polyester

Polymer blends of polyethersulfone (PES) with an all aromatic liquid crystalline co-polyester (LCP) were investigated. In addition, PES oligomers with the reactive functions end groups (?ONa) were added as a third component to the above blends in order to improve their properties. Flexural properties, such as modulus and strength, and dynamic viscoelastic properties, such as dynamic storage elasticity (E′) and loss tangent (tan δ), of the blends were measured. The morphology of blends was characterized using a differential scanning calorimeter (DSC) and a scanning electron microscope (SEM). Of the flexural properties, the modulus of PES increased almost linearly with increasing LCP content. However, strength decreased as LCP content increased to 20 wt%. In contrast, the addition of the PES oligomers had little effect on modulus, but strength was clearly improved. Regarding dynamic viscoelastic properties, the oligomer-containing blends exhibited complex behavior. Regarding morphologies, SEM analysis revealed that the LCP was not fibrous in the core of the blend containing 40 wt% or less, but the addition of the PES oligomers made LCP fibrous even in blends with low LCP content. It was concluded that the PES oligomers with reactive functional groups acted as a compatibilizer in polymer blends of PES/LCP.     

Structural properties and impact fracture behavior of injection molded blends of liquid crystalline copolyester and modified poly(phenylene oxide)

Blends of a thermotropic liquid crystalline polymer (LCP) with modified poly (phenylene oxide) (PPO) were injection molded. The morphology, tensile properties and dynamic mechanical behavior of the blends have been studied as a function of LCP content. Furthermore, the impact performance of these blends has been investigated by the instrumented Izod and Charpy falling weight tests. The critical strain energy release rate (G_IC) of the blends were determined and the G_IC values were found to be dependent on the LCP content. The results are discussed and explained in terms of materials morphology.     

Mechanical performance of blends of thermotropic liquid crystalline polymer spheres‐dispersed polycarbonate

Liquid crystalline polymer (LCP) blends with a thermotropic LCP dispersed in the form of microspheres is studied to show the role of LCP spheres. Polycarbonate (PC), p‐hydroxybenzoic acid–poly(ethylene terephthalate) copolyester, and random styrene–maleic anhydride copolymer are used as the matrix, the dispersed phase, and the compatibilizer, respectively. A scanning electron microscopy observation shows the formation of LCP spheres with improved interfacial adhesion in the injection‐molded samples via compatibilization. The mechanical tests show increased modulus, elongation at break, and fracture‐absorbed energy of blends of LCP spheres‐dispersed PC. This shows an optimistic potential for the dispersed LCP phase, in spite of its morphology in the form of fibrils for reinforcing the matrix or in the form of microspheres for toughening the matrix. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1493–1499, 2003     

Rheology and thermal properties of liquid crystalline copolyester and poly(ethylene 2,6-naphthalate) blends

Blends of a poly(ethylene 2,6-naphthalate) (PEN) and a liquid crystalline copolyester (LCP), poly(benzoate-naphthoate) were prepared in a twin-screw extruder. Specimens for thermal properties were investigated by means of an instron capillary rheometer (ICR) and scanning electron microscopy (SEM). The blend viscosity showed a minimum at 10 wt% of LCP and increased with increasing LCP content above 10 wt% of LCP. Above 50% of LCP and at higher shear rate, phase inversion occured and the blend morphology was fibrous and similar to pure LCP. The ultimate fibrillar structure of LCP phase appeared to be closely related to the extrusion temperature. By employing a suitable deformation history, the LCP phase may be elongated and oriented such that a microfibrillar morphology can be retained in the solid state. Thermal properties of the LCP/PEN blends were studied using DSC and a Rheovibron viscoelastomer. These blends were shown to be incompatible in the entire range of the LCP content. For the blends, the T_g and Tm were unchanged. The half time of crystallization for the LCP/PEN blends decreased with increasing LCP content. Therefore, the LCP acted as a nucleating agent for the crystallization of PEN. The dimensional and thermal stability of the blends were increased with increasing LCP content. In studies of dynamic mechanical properties, the storage modulus (E′) was improved with increasing LCP content and synergistic effects were observed at 70 wt% of LCP content. The storage modulus for the LCP/PEN 70/30 blend is twice that of PEN matrix and exceeded pure LCP.     

In situ composites from blends of polycarbonate and a thermotropic liquid‐crystalline polymer: The influence of the processing temperature on the rheology,morphology, and mechanical properties of injection‐molded microcomposites

This work was aimed at understanding how the injection‐molding temperature affected the final mechanical properties of in situ composite materials based on polycarbonate (PC) reinforced with a liquid‐crystalline polymer (LCP). To that end, the LCP was a copolyester, called Vectra A950 (VA), made of 73 mol % 4‐hydroxybenzoic acid and 27 mol % 6‐hydroxy‐2 naphthoic acid. The injection‐molded PC/VA composites were produced with loadings of 5, 10, and 20 wt % VA at three different processing barrel temperatures (280, 290, and 300°C). When the composite was processed at barrel temperatures of 280 and 290°C, VA provided reinforcement to PC. The resulting injection‐molded structure had a distinct skin–core morphology with unoriented VA in the core. At these barrel temperatures, the viscosity of VA was lower than that of PC. However, when they were processed at 300°C, the VA domains were dispersed mainly in spherical droplets in the PC/VA composites and thus were unable to reinforce the material. The rheological measurements showed that now the viscosity of VA was higher than that of PC at 300°C. This structure development during the injection molding of these composites was manifested in the mechanical properties. The tensile modulus and tensile strength of the PC/VA composites were dependent on the processing temperature and on the VA concentrations. The modulus was maximum in the PC/VA blend with 20 wt % VA processed at 290°C. The Izod impact strength of the composites tended to markedly decrease with increasing VA content. The magnitude of the loss modulus decreased with increasing VA content at a given processing temperature. This was attributed to the anisotropic reinforcement of VA. Similarly, as the VA content increased, the modulus and thus the reinforcing effect were improved comparatively with the processing temperature increasing from 280 to 290°C; this, however, dropped in the case of composites processed at 300°C, at which the modulus anisotropy was reduced. Dynamic oscillatory shear measurements revealed that the viscoelastic properties, that is, the shear storage modulus and shear loss modulus, improved with decreasing processing temperatures and increasing VA contents in the composites. Also, the viscoelastic melt behavior (shear storage modulus and shear loss modulus) indicated that the addition of VA changed the distribution of the longer relaxation times of PC in the PC/VA composites. Thus, the injection‐molding processing temperature played a vital role in optimizing the morphology‐dependent mechanical properties of the polymer/LCP composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Transport properties of methanol in blends of a liquid crystalline copolyester and polyethersulfone

Data for the diffusivity and solubility of methanol in blends of polyethersulfone (PES) and a liquid crystalline copolyester (polyhydroxy-benzoic acid (73 mol%)-co-hydroxy-naphthoic acid (27 mol%)) (LCP) are reported. Samples taken from injection molded and compression molded specimens over a wide composition range were studied by gravimetry (sorption and desorption), dielectric spectroscopy, differential scanning calorimetry and scanning electron microscopy. The sorption of methanol in PES led to the formation of an ordered phase. The sorption curves were S-shaped and they could be described by a diffusion model assuming a concentration-dependent diffusivity and time-dependent boundary conditions. The solubility of methanol in the blends was strictly proportional to the PES content. The zero-concentration-diffusivity decreased strongly with increasing LCP content and it was dependent on the morphology. Injection molding yielded samples with a fibrillar LCP phase with a greater continuity of the PES component and a high diffusivity (in relative terms). Compression molding led to samples with a more continuous LCP component even at low LCP contents and a low diffusivity.     

Thermal and mechanical properties of injection molded blends of a liquid crystalline polymer and poly(butylene terephthalate)

The microstructure and the thermal and mechanical properties of injection molded samples of different blends of Vectra (LCP) and poly(butylene terephthalate) (PBT) have been studied. Differential scanning calorimetry and hot-stage polarized light microscopy showed that the crystallization of PBT was unaffected by the presence of LCP. X-ray diffraction showed that the PBT component was always unoriented in the injection molded samples. Blends with less than 28 vol% LCP exhibited the same stiffness and the same coefficient of linear thermal expansion as PBT. Blends containing more than 38 vol% LCP contained an oriented LCP phase and had a stiffness in accordance with the upper-bound composite equation. The coefficients of linear thermal expansion for these blends were close to that of pure LCP.