隔离三电平零电压直流变换器

介绍了一种隔离三电平零电压直流变换器。其主开关管的电压应力均为输入电压的一半。由于采用了交错ZVSPWM控制并利用输出滤波电感中的能量,因此能够在宽负载范围内实现开关管的ZVS。分析了该变换器的工作原理和工作特性,并通过一个480W（输出48V／10A）的原理样机进行了验证,最后给出了实验结果。     

Design and Implementation of an Accurately Regulated Multiple Output ZVS DC–DC Converter

An accurately regulated multiple-output zero-voltage switching (ZVS) DC-DC converter is proposed. The converter is composed of three outputs altogether. The first and second outputs are regulated through the duty cycle control of two asymmetrical half bridge converters, while the third output is regulated through the phase shift of the two asymmetrical half bridge converters. The characteristic of this multiple-output dc-dc converter is analyzed and design process is investigated. ZVS is realized for all the main switches. Therefore this multiple-output dc-dc converter can operate with higher efficiency at higher switching frequency. The operation stages, ZVS condition and control detail are also presented. A 400 V input, 48 V/10 A, 5 V/20 A, 12 V/5 A outputs prototype is built to verify the design. The efficiency at rated input voltage full load is 93.36%.     

一种宽输入电压范围软开关电流型DC/DC转换器

针对太阳能光伏及燃料电池等领域电源需要较宽输入电压范围的需求,提出一种通用的具有较宽输入电压范围的软开关电流型DC/DC转换器。该转换器采用了固定频率混合调制设计,可以在所有工作条件下实现半导体器件的软开关工作,并采用电流馈电技术以便适用于低电压高电流的电源。相较于传统转换器,该转换器更为通用,能够实现零电压开关和零电流开关,并且能够在输入电压和负载变化出现较大变化时控制输出电压。实验结果显示,在20-60V输入电压范围内且负载出现变化时,该转换器均表现出良好的性能。     

The three-level ZVS-PWM DC-to-DC converter

A novel high-frequency DC-to-DC power converter for high voltage and high power is introduced which features zero voltage switching (ZVS), operation at constant frequency, regulation by pulse width modulation (PWM), and low RMS current stress upon power switches. Its greatest attribute, in comparison with the full-bridge (FB-ZVS-PWM) converter, is that the voltage across the switches is half of the input voltage, This property is achieved due to the use of a three-level leg in place of the conventional two-switch leg. Operation, analysis, design procedure and example, and simulation are presented. A prototype operating at 100 kHz, rated at 600 V input voltage, and 1.5 kW output power and 25 A output current has been fabricated and successfully tested in the laboratory. The measured efficiency at full load was 93%     

A Novel ZVS Resonant Reset Dual Switch Forward DC–DC Converter

This paper presents a new topology named zero-voltage switching (ZVS) resonant reset dual switch forward dc-dc converter, which, compared with resonant reset single switch forward dc-dc converter, maintains the advantage that duty cycle can be more than 50%, at the same time disadvantages of high voltage stress for main switches and low efficiency are overcome. In addition, ZVS is achieved for all switches of the presented topology. Therefore, this proposed topology is very attractive for high voltage input, wide range, and high efficiency applications. In this paper, the operation principle and characteristic of this topology are analyzed in detail. Next, the design consideration is presented. Finally, the advantages mentioned above are verified by experimental results     

An Analysis of the ZVS Two-Inductor Boost Converter under Variable Frequency Operation

The two-inductor boost converter has been previously presented in a zero-voltage switching (ZVS) form where the transformer leakage inductance and the MOSFET output capacitance can be utilized as part of the resonant elements. In many applications, such as maximum power point tracking (MPPT) in grid interactive photovoltaic systems, the resonant two-inductor boost converter is required to operate with variable input output voltage ratios. This paper studies the variable frequency operation of the ZVS two-inductor boost converter to secure an adjustable output voltage range while maintaining the resonant switching transitions. The design method of the resonant converter is thoroughly investigated and explicit control functions relating the circuit timing factors and the voltage gain for a 200-W converter are established. The converter has an input voltage of 20V and is able to produce a variable output voltage from 169V to 340V while retaining ZVS with a frequency variation of 1MHz to 407kHz. Five sets of theoretical, simulation and experimental waveforms are provided for the selected operating points over the variable load range at the end of the paper and they agree reasonably well. The converter has achieved part load efficiencies above 92% and an efficiency of 89.6% at the maximum power of 200W     

A 1-MHz Zero-Voltage-Switching Asymmetrical Half-Bridge DC/DC Converter: Analysis and Design

The asymmetrical half-bridge (AHB) topology discussed in this paper is one of the complementary driven pulse-width modulated converter topologies, which presents an inherent zero-voltage switching (ZVS) capability. In the previous work, the ideal operation of the converter and the ZVS realization process have been analyzed. However, the influence of the circuit parasitics on the output voltage drop and the design constraints of the circuit parameters to ensure the ZVS operation have not been investigated. The minimum load needed to ensure the ZVS operation is also not readily available. This paper presents a detailed and practical design for a 1-MHz AHB converter. A revised voltage transfer ratio of the converter is derived considering the influence of circuit parasitics and the ZVS transition. Two circuit parameters responsible for maintaining the ZVS operation are the transformer leakage inductance and the interlock delay time between the gate signals of two switches. A design method of the two parameters is proposed, which can ensure the ZVS transition. The possible ZVS range of the load variation is also investigated. A 50-W AHB converter with 1-MHz switching frequency was constructed, and a maximum efficiency of 91% was achieved.     

Analysis and Implementation of a ZVS-PWM Converter With Series-Connected Transformers

This brief presents the analysis, design, and implementation of zero-voltage switching (ZVS) active clamp converter with series-connected transformer. A family of isolated ZVS active clamp converters is introduced. The technique of the adopted ZVS commutation will not increase additional voltage stress of switching devices. In the adopted converter with series-connected transformer, each transformer can be operated as an inductor or a transformer. Therefore, no output inductor is needed. To reduce the voltage stress of the switching device in the conventional forward converter, the active clamp technique is used to recycle the energy stored in the transformer leakage back into the input dc source. Finally, experimental results are presented taken from a laboratory prototype with 100-W rated power, input voltage of 155 V, output voltage of 5 V, and operating at 150 kHz. [All rights reserved Elsevier].     

A novel self-oscillating, boost-derived DC-DC converter with load regulation

This paper proposes a novel self-oscillating, boost-derived (SOBD) dc-dc converter with load regulation. This proposed topology utilizes saturable cores (SCs) to offer self-oscillating and output regulation capabilities. Conventionally, the self-oscillating dc transformer (SODT) type of scheme can be implemented in a very cost-effective manner. The ideal dc transformer provides both input and output currents as pure, ripple-free dc quantities. However, the structure of an SODT-type converter will not provide regulation, and its oscillating frequency will change in accordance with the load. The proposed converter with SCs will allow output-voltage regulation to be accomplished by varying only the control current between the transformers, as occurs in a pulse-width modulation (PWM) converter. A control network that combines PWM schemes with a regenerative function is used for this converter. The optimum duty cycle is implemented to achieve low levels of input- and output-current ripples, which are characteristic of an ideal dc transformer. The oscillating frequency will spontaneously be kept near-constant, regardless of the load, without adding any auxiliary or compensation circuits. The typical voltage waveforms of the transistors are found to be close to quasisquare. The switching surges are well suppressed, and the voltage stress of the component is well clamped. The turn-on/turn-off of the switch is zero-voltage switching (ZVS), and its resonant transition can occur over a wide range of load current levels. A prototype circuit of an SOBD converter shows 86% efficiency at 48-V input, with 12-V, 100-W output, and presents an operating frequency of 100 kHz.     

Analysis and Design for a New ZVS DC–DC Converter With Active Clamping

A new zero voltage switching (ZVS) boost converter is presented in this paper. By using an auxiliary switch and a capacitor, ZVS for all switches is achieved with an auxiliary winding in one magnetic core. A small diode is added to eliminate the voltage ringing across the main rectifier diode. This clamping technique can also be utilized in other dc-dc converters, and a family of new ZVS dc-dc converter is derived. A prototype (500 W/193 kHz) is made to verify the theoretical analysis. The efficiency is higher than 94% at 90-V input at full load     

1-kW PFC converter with compound active-clamping

A PFC converter employing compound active clamping technique is proposed. It can effectively reduce the loss caused by diode reverse recovery. Both the main switch and the auxiliary switch can achieve soft-switching (ZVS) under certain conditions. The parasitic oscillation caused by the parasitic capacitance of the boost diode is eliminated. The voltage on the main switch, the auxiliary switch and the boost diode are clamped. The principle of operation and theoretical analysis are presented. The maximum voltage stress of switches and the soft-switching region with relation to the resonant inductor and resonant capacitance are investigated. A prototype of 1kW is built to test the proposed topology. The input voltage is from 90V/sub rms/ to 265V/sub rms/. The output voltage is 380V. The operation frequency is 100 kHz. The measured efficiency at full load with different input voltage is from 93.5% to 97.8%.     

A single-stage power factor correction AC/DC converter based on zero voltage switching full bridge topology with two series-connected transformers

A single-stage power factor correction ac/dc converter based on zero voltage switching (ZVS) full bridge topology with two series-connected transformers is proposed in this paper. The proposed converter offers a very wide ZVS range due to the configuration of two series-connected transformers. It features a high efficiency over wide load ranges. Furthermore, it shows the low voltage stress on a dc link capacitor. The proposed converter also gives the high power factor and low input current harmonics complied with IEC 61000-3-2 Class D requirements by integrating a boost stage operated in a discontinuous current mode. The ZVS conditions, large signal modeling, and design procedure are discussed in detail. Experimental results are presented to show the validity of the proposed converter.     

High-Efficiency Boost Half-Bridge Converter With Fast Boost Current Transferring ZVS Operation

A new boost half bridge (BHB) converter is presented. It is composed of additional switch, diode and coupled winding to boost inductor of BHB converter. Using the transferring of boost inductor current to coupled winding in a short period, the cancellation of zero voltage switching (ZVS) current, which always occurs in convention one, is prevented. Therefore, the ZVS operation is easily achieved by leakage inductor current of transformer. Furthermore, since negatively build-up leakage inductor current of boost winding helps the ZVS operation throughout full load range, the excellent ZVS operation and high efficiency is achieved.      

A novel zero-Voltage-switching PWM boost rectifier with high power factor and low conduction losses

This paper proposes a new single-phase high-power-factor rectifier, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-voltage-switching PWM (ZVS-PWM) auxiliary circuit is configured in the presented ZVS-PWM rectifier to perform ZVS in the main switches and the passive switches, and zero-current switching in the auxiliary switch. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZVS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path, and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Nine transition states for describing the behavior of the ZVS-PWM rectifier in one switching period are described. A prototype rated at 1 kW, operating 80 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage of 400 V/sub dc/ has been implemented in the laboratory. An efficiency of 96.7% and power factor over 0.99 has been measured. Analysis, design, and the control circuitry are also presented in this paper.     

Analysis and Optimal Design Considerations for an Improved Full Bridge ZVS DC–DC Converter With High Efficiency

This paper proposes an improved full bridge dc–dc converter, which can achieve zero-voltage-switching (ZVS) with wide input voltage range and load range. The operation principle of the converter and the optimal design considerations for high efficiency and ZVS range are analyzed. By adding two clamp diodes and two small coupled inductors at the primary side of the transformer, the voltage ringing across rectifier diodes is reduced. Therefore, Schottky diodes can be employed to reduce conduction loss, and high efficiency is achieved. A 1.2-kW/105-kHz prototype was made with an efficiency higher than 95% at full load to verify the theoretical analysis.     

A modified asymmetrical pulse-width-Modulated resonant DC/DC converter topology

A modified asymmetrical pulse-width-modulated resonant dc/dc converter employing an auxiliary circuit will be proposed in this paper. The auxiliary circuit consists of a network of two capacitors and an inductor. The aim of this network is to produce zero-voltage-switching (ZVS) over a wide input voltage range, while reducing the voltage stress on the resonant component. A detailed analysis and performance characteristics are presented. Experimental results for a 5 V, 35 W converter show an efficiency of 83% at a constant operating frequency of 500 kHz. Using metal oxide semiconductor field effect transistors (MOSFETs) as synchronous rectifiers can further reduce power losses and improve the efficiency to be greater than 90%.     

High-precision current source using low-loss, single-switch,three-phase AC/DC converter

A three-phase AC/DC converter based on isolated Cuk topology feeding an inductive load is presented. The main goal is to get a compact, highly stable current source to feed an electromagnet. A high power factor is achieved, at constant duty-cycle and switching frequency, by discontinuous input current mode operation. The converter presents a linear relationship between the duty-cycle and the output current, making it easier to design the control system. Additionally the voltage stress on the power transistor is constant and does not depend on the duty-cycle. An auxiliary circuit allows zero voltage turn-off while limiting the over-voltage on the switch produced by the transformer leakage inductance. Pulse-width modulation (PWM) control is used to reduce sensitivity to line disturbances and to eliminate the 300-Hz ripple on the output current. Experimental measurements taken on a 400-W prototype confirm theoretical forecasts     

A Three-Phase Current-Fed Push–Pull DC–DC Converter

In this paper, a new three-phase current-fed push–pull dc–dc converter is proposed. This converter uses a high-frequency three-phase transformer that provides galvanic isolation between the power source and the load. The three active switches are connected to the same reference, which simplifies the gate drive circuitry. Reduction of the input current ripple and the output voltage ripple is achieved by means of an inductor and a capacitor, whose volumes are smaller than in equivalent single-phase topologies. The three-phase dc–dc conversion also helps in loss distribution, allowing the use of lower cost switches. These characteristics make this converter suitable for applications where low-voltage power sources are used and the associated currents are high, such as in fuel cells, photovoltaic arrays, and batteries. The theoretical analysis, a simplified design example, and the experimental results for a 1-kW prototype will be presented for two operation regions. The prototype was designed for a switching frequency of 40 kHz, an input voltage of 120 V, and an output voltage of 400 V.      

一种新颖有源箝位ZVS正激变换器的研究

介绍了一种中心抽头全波整流有源箝位ZVS正激变换器的工作原理及主要参数计算。有源箝位电路由一个箝位开关管和箝位电容组成。变压器磁芯实现无损复位,励磁能量和漏感能量全部传递到负栽.磁芯利用率高,功率开关管承受电压应力降低。通过变压器漏感与开关管输出电容的谐振,主开关管与箝位开关管都可以实现ZVS开通,提高了变换器工作效率。文章首先分析了变换器工作原理,然后给出了主要参数的计算方法,最后通过样机(48V输入5V/20A输出)实验验证了该拓扑的高效性能。     

A new single-phase ZCS-PWM boost rectifier with high power factor and low conduction losses

This paper proposes a new single-phase high-power-factor rectifier, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the active switches and zero-voltage switching (ZVS) in the passive switches. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved because of the following reasons: 1) the circulating current for the soft switching flows only through the auxiliary circuit; 2) a minimum number of switching devices are involved in the circulating current path; and 3) the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Seven transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM-switch model is used to predict the system performance. A prototype rated at 1 kW, operating at 60 kHz, with an input alternating current voltage of 220 V/sub rms/ and an output voltage of 400 V/sub dc/, has been implemented in laboratory. An efficiency of 98.3% and a power factor over 0.99 have been measured. Analysis, design, and the control circuitry are also presented in this paper.