浓度对传质系数的影响及多元物系传质

在筛板塔中对甲醇-乙醇-水三元物系进行精馏传质过程实验,考虑浓度对传质系数的影响建立了一个数学模型,对各组分在塔中的浓度分布进行模拟计算,计算结果能正确反映各组分在塔中浓度分布的变化规律.实验与计算结果都表明在某些浓度范围内乙醇呈现出比较复杂的变化规律.     

EFFECT OF STATIC LIQUID HEIGHT ON GAS-LIQUID MASS TRANSFER IN A DRAFT-TUBE BUBBLE COLUMN AND THREE-PHASE FLUIDIZED BED

Experiments are performed under batch-liquid operating conditions to investigate the effect of static liquid height on the gas-liquid mass transfer coefficient (K_La) in a draft-tube bubble column (DTBC) and a draft-tube three-phase fluidized bed (DTFB). In addition, the effects of column diameter, gas-distributor, and draft-tube diameter are studied. The results indicate that for a given system with a porous plate gas-distributor at low superficial gas velocities (<70 m/hr), increasing static liquid height decreases K_La. At high gas velocities, K_La is independent of the static liquid height. For systems with a perforated gas-distributor, there is no effect of static liquid height on K_La. The formation of small dispersed bubbles at low gas velocities in the porous plate distributor system accounts for the considerably high K_La values and the observed effect of liquid height. On the other hand, the formation of large spherical-cap bubbles and the bubble coalescence at high gas velocities reduce the performance of the porous plate distributor system to that of the perforated one.     

喷雾塔内的传质

在直径为0.4m、高3m的实验塔中,采用NH_3-H_2O系统,以外混二流式喷嘴作雾化器,研究喷雾塔内的传质(?)在单个液滴传质方程式的基础上,结合喷雾塔内液滴群的运动特点,导出喷雾塔内液滴群的体积传质系数与持液量、索特尔平均直径及两相相对速度之间的关系。通过实验数据的拟合,获得关联式:Kya=2.320×10~(-4)×HLdvs~(-1.2152)Z~(-0.7778)[Ud/HL-Uc/(1-HL)]~(0.7848)。该式计算结果与实验数据十分吻合。     

鼓泡塔中气含率的温度和电解质效应

在直径0.10m、高1.05m 的鼓泡塔中,对空气-水、乙醇、5%NaCl(aq)、5%KCl(aq)、5%CaCl_2(aq)、5%Na_2SO_4(aq)、2.34%MgCl_2(aq)等物系气含率的温度效应和电解质效应进行了实验研究。通过引入((P+Ps)/P)数群很好地关联了气含率的温度效应,找出了气含率的电解质校正因子与液相离子强度的关系。     

MASS TRANSFER AND PHASE HOLDUP CHARACTERISTICS IN THREE-PHASE FLUIDIZED BEDS

The effects of liquid surface tension (42.6 ∼ 72,4 mN/m) and viscosity (1 ∼214mPa • sⁿ), liquid (0.01 ∼0.12m/s) and gas (0.01 ∼0.20m/s) velocities and particle sizes (1 — 8 mm) on phase holdup and mass transfer coefficient ( k_La) have been determined in a 0.142 m-I.D. × 2.0 m-high Plexiglas column. The gas phase holdup increases with liquid velocity, and the rate of increase in gas phase holdup sharply increases with gas velocity in the bed of surfactant solutions. In the beds of 1.0 and 1.7 mm glass beads, the bed contraction occurs whereas in the beds of 2.3 mm glass beads the bed contraction does not occur with an aqueous soltuion of ethanol (σ = 50.4 mN/m). The value of k_La increases with decreasing surface tension (σ ) but it decreases exponentially with increasing liquid viscosity in continuous bubble columns and three-phase fluidized beds. In three-phase fluidized beds with surfactant solutions, k_La increases with gas and liquid velocities and particle size. In three-phase fluidized beds of viscous or surfactant soltuions, k_L,a can be estimated in terms of the energy dissipation rate based on the isotropic turbulence theory and a flow regime map is proposed based on the drift flux theory.     

A STUDY ON MASS TRANSFER IN PULSED SIEVE-PLATE EXTRACTION COLUMN

Mass transfer experiments have been carried out in a 40mm diameter pulsed sieve-plate extraction column. Both standard and "dispersion-coalescence" type cartridges were tested with 30％ TBP (kerosene as diluent)/ Nitric Acid/Water system. "Ture" volumetric mass transfer coefficient and backmixing     

HYDRODYNAMICS AND MASS TRANSFER IN DOWNFLOW BUBBLE COLUMN

Gas holdup, effective interfacial area and volumetric mass transfer coefficient were measured in two and three phase downflow bubble columns. The mass transfer data were obtained using the chemical method of sulfite oxidation, and the gas holdup was measured using the hydrostatic technique. Glass beads and Triton 114 were used to study the effects of solids and liquid surface tension on the gas holdup and the mass transfer parameters a and k_L a . The gas holdup in three phase systems was measured for non-wettable (glass bead) and wettable (coal and shale particles) solids.

The mass transfer data obtained in the downflow bubble column were compared with the values published for upflow bubble columns. The results indicate that in the range of superficial gas velocities (0.002-0.025) m/s investigated, the values of the mass transfer coefficient were of the same order of magnitude as those observed in upflow systems, but the values of interfacial area were at least two fold greater. Also, the results showed that the operating variables and the physical properties had different influences on a and k_L a in the downflow bubble column. Correlations for a and k_L a for the downflow bubble column are proposed which predict the data with adequate accuracy in the range of operating conditions investigated.     

HYDRODYNAMICS AND MASS TRANSFER IN DOWNFLOW BUBBLE COLUMN

Gas holdup, effective interfacial area and volumetric mass transfer coefficient were measured in two and three phase downflow bubble columns. The mass transfer data were obtained using the chemical method of sulfite oxidation, and the gas holdup was measured using the hydrostatic technique. Glass beads and Triton 114 were used to study the effects of solids and liquid surface tension on the gas holdup and the mass transfer parameters a and k_La. The gas holdup in three phase systems was measured for non-wettable (glass bead) and wettable (coal and shale particles) solids.

The mass transfer data obtained in the downflow bubble column were compared with the values published for upflow bubble columns. The results indicate that in the range of superficial gas velocities (0.002-0.025) m/s investigated, the values of the mass transfer coefficient were of the same order of magnitude as those observed in upflow systems, but the values of interfacial area were at least two fold greater. Also, the results showed that the operating variables and the physical properties had different influences on a and k_La in the downflow bubble column. Correlations for a and k_La for the downflow bubble column are proposed which predict the data with adequate accuracy in the range of operating conditions investigated.     

EFFECT OF SURFACTANT CONCENTRATION ON GAS HOLDUP IN A BUBBLE COLUMN WITH AN ORGANIC LIQUID

This work presents an experimental analysis of the effect of the addition of a surfactant on gas holdup in a bubble column with an organic liquid phase. For the system considered, the addition of surfactant increases the gas holdup by increasing the volume of foam within the column. The surfactant concentration has negligible effect on the intrinsic gas holdup of both the bubbling and foaming regions.     

EFFECT OF HIGH VOIDAGE ON MASS TRANSFER COEFFICIENT IN A FLUIDIZED BED

Experiments were carried out to determine the gas-solid mass transfer coefficient for the air-naphthalene system under fast-fluidized conditions. The data were obtained under conditions of high voidage (as high as 98%) and high gas velocities (0·5 m/s-2·2 m/s). The results indicate that the correlation for the mass-transfer coefficient in a gas-solid fluidized bed under low voidage conditions established by previous investigators can be extended to the fast fluidization regime. Significantly lower mass transfer coefficients were, however, obtained under high voidage compared to low voidage conditions.     

溶胀对膜萃取传质性能的影响

溶剂对膜的溶胀,使膜的物理结构发生变化,进而对膜萃取传质性能产生一定的影响。本文以３０％ＴＢＰ（煤油）－醋酸－水,正丁醇－醋酸－水和２０％７３０１（煤油）－醋酸－水为实验体系在聚砜和聚四氟乙烯微孔平板膜器中系统地了溶胀地膜萃取总传质系数的影响。结果表明,微孔膜发生溶胀后孔隙率发生明显的变化,其总传质系数有较大的下降。     

超临界流体喷淋萃取塔流体力学特性和传质性能

在内径为25mm的连续逆流喷淋塔内进行了流体力学特性和质量传递性能的研究,实验压力为(8～14)MPa,实验温度为35℃,实验体系为CO_2/异丙醇/水和CO_2/乙醇/水.建立了描述连续逆流超临界流体喷淋萃取塔的流体力学关联式,根据双膜理论,建立了用于计算液相总体积传质系数的质量传递模型.流体力学关联式和质量传递模型的计算值与实验结果符合较好.     

PREDICTION OF GAS-PHASE HOLDUP IN A BUBBLE COLUMN

Hydrodynamic properties of bubble columns play a significant role in many chemical and biochemical processes. Recent theoretical and experimental work conducted by Krishna et al. (1991, 1994), and Wilkinson et al. (1992) have been examined in conjunction with a bubble column and data for the air-water system operating at ambient conditions. The bubble column is 0.108 m in internal diameter, has a 1.70 m tall test section, and is equipped with a perforated plate distributor having 91 holes of 0.8 mm diameter. The data are taken for five values of the slumped water column height in range from 0.79 to 1.15 m, and for superficial air velocities up to about 0.4 m/s.

The data accord to the qualitative aspects of Krishna et al. model but lead to different values of the bubble swarm rise velocity, and superficial transition air velocity characterizing the transition from homogeneous bubbly flow regime to heterogeneous churn-turbulent flow regime. The quantitative reproduction by the model expressions of these recent works of the experimental data is poor. This may be partly attributed to the geometry of the column, diameter and distributor design.

The qualitative features of Krishna et al. model for the two regimes are confirmed by the present data. For quantitative predictions of gas-phase holdup, a new model is proposed in which the large bubble flow in the churn-turbulent regime is formulated following the drift-flux theory. The proposed theory and experimental data are in good agreement.     

低分子量有机添加剂对内环流反应器中气含率和气液传质系数的影响

研究了气升式内循环气液两相流反应器中某些添加剂(脂肪醇类、酯类、氨基酸类等)对传质特性的影响.实验发现氨基酸对传质几乎没有影响;正丁醇和乙酸乙酯对气液间传质有强化作用;而正己醇和乙酸丁酯仅在一定范围内增强传质,从而使体积传质系数出现了峰值.分析了体积传质系数k     

EFFECT OF VISCOSITY AND DRAG REDUCING AGENTS ON MASS TRANSFER IN LIQUID-LIQUID SPRAY COLUMNS

The effects of dispersed phase viscosity and drag reducing agents on liquid-liquid mass transfer has been investigated in a 52 mm i.d. spray column. Methyl lsobutyl ketone was used as the continuous phase. Aqueous solutions of polyethylene glycol (0-60% w/w) and polyacrylamide (0-500 ppm)were used as the dispersed phase.

Correlations have been developed for fractional phase holdup and mass transfer coefficient.     

EFFECT OF FREE STREAM TURBULENCE ON HEAT AND MASS TRANSFER FROM A SPHERE

A model has been proposed for the momentum eddy diffusivity induced by free stream turbulence intensity. The eddy diffusivity model is applied to a sphere situated in a uniform crossflow in the presence of free stream turbulence. Numerical solution of the governing momentum and energy equations with the proposed eddy diffusivity model yielded results for the heat/mass transfer rates. The numerical predictions of the present work are compared with experimental data and the agreement between the two is seen to be very good.     

温度对气态膜过程传质性能影响

本文通过对文献数据的整理计算,说明对于易挥发体系(溶解度系数Hf<<1),温度主要影响组分在液相的扩散系数对气态膜过程的总传质系数产生影响;对于具有中等溶解度的体系(Hf≈1),传质同时受液相阻力和膜阻控制;对于难挥发体系(Hf>>1),温度主要通过改变气液平衡关系对传质系数产生影响。     

EFFECT OF FREE STREAM TURBULENCE ON HEAT AND MASS TRANSFER FROM A SPHERE

A model has been proposed for the momentum eddy diffusivity induced by free stream turbulence intensity. The eddy diffusivity model is applied to a sphere situated in a uniform crossflow in the presence of free stream turbulence. Numerical solution of the governing momentum and energy equations with the proposed eddy diffusivity model yielded results for the heat/mass transfer rates. The numerical predictions of the present work are compared with experimental data and the agreement between the two is seen to be very good.     

气—液鼓泡塔中流动域和气含率的分布

利用压力传感器测定了气、液两相鼓泡塔内不同轴、径向位置上压强的脉动信号,分析了压强的脉动特征,计算了各种操作条件下塔内不同轴向位置截面上的平均气含率,发现在不同操作条件下,塔内可能出现不同的流动域分布,即全塔均匀鼓泡域、全塔过渡域、全塔湍动鼓泡域以及均匀鼓泡域,过渡域和湍动鼓泡域中的相邻2种或3种流域同时出现在塔内不同高度上。提出了不同轴向位置流域转变的判据。并发现,同一截面的不同径向位置基本处于同一流域内。同时研究了鼓泡塔内气含率在轴向上的分布规律,给出了不同流动域内气含率的关系式。     

GAS-LIQUID MASS TRANSFER IN JET BUBBLE COLUMN

The jet bubble column consists of a conical entrance section which expands to a cylindrical column. Gas and liquid are co-currently introduced at the bottom of the column by a small diameter inlet pipe which acts like an ejector. The kinetic energy of the gas and liquid jet together with the conical geometry at the lower section of the column cause the formation and dispersion of small bubbles.

Gas-liquid mass transfer in the jet bubble column (61 cm diameter) was measured by a dynamic response technique, in which a step change was made in the gas phase oxygen concentration and the aqueous dissolved oxygen concentration response was measured at various axial and radial locations. It was found that a continuous stirred tank reactor model could be used to evaluate experimental results. The volumetric mass transfer coefficient in this type of system was found to increase with increasing gas flow rate and was about 1.5 times larger than the values obtained at similar conditions in conventional bubble columns. Preliminary measurements and calculations indicate negligible effects of liquid velocity and bed height on the mass transfer coefficient.