碳/碳复合材料力学性能的研究进展

本文综述了碳/碳复合材料力学性能的研究进展,包括碳纤维、基体炭、界面性能、制备工艺及工艺参数等对碳/碳复合材料力学性能的影响。同时简单介绍了当今单向碳/碳复合材料力学性能的表征手段。希望对碳/碳复合材料力学性能的研究及应用提供帮助。     

Effect of carbon nanofiber functionalization on the in-plane mechanical properties of carbon/epoxy multiscale composites

In this work, vapor-grown carbon nanofibers (CNFs) were functionalized using an optimized route and dispersed in the matrix of carbon fabric-reinforced epoxy composites to develop multiscale carbon/epoxy composites. Functionalization was carried out through an oxidative treatment with a mixture of HNO₃/H₂SO₄ (1 : 3) using a combination of ultrasonication and magnetic stirring. Functionalized CNFs (F-CNFs) were characterized for their morphology, length, functional groups, and degradation due to oxidative treatment. The results showed that it was possible to efficiently functionalize CNFs without any degradation through proper selection of treatment duration. F-CNFs were dispersed homogeneously into the epoxy matrix using ultrasonication in combination with high-speed mechanical stirring. The incorporation of 0.1 wt % F-CNFs led to a 65% increase in Young's modulus and a 36% in tensile strength of neat carbon/epoxy composites. The fracture surfaces were studied using scanning electron microscopy to understand the property enhancement due to F-CNFs. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

多壁碳纳米管／环氧树脂复合材料性能研究

采用物理机械方法与化学方法相结合的手段,制备了多壁碳纳米管（MWNTS）／环氧树脂（Epoxy）复合材料。通过力学拉伸试验测试了MWNTs/Epoxy复合材料拉伸强度和拉伸模量与MWNTS添加量的关系,利用扫描电镜（SEM）分析了MWNTS／Epoxy复合材料的拉伸断面,并用表面电阻测试仪对所制备的碳纳米管复合材料进行了电学性能测试。结果表明：经过化学酸化的方法处理后的MWNTS在复合材料中的分散得到了改善,力学性能也得到了明显的提高,但酸处理后的复合材料的电学性能明显低于未处理的复合材料。     

Effects of organo‐montmorillonite on the mechanical and morphological properties of epoxy/glass fiber composites

Epoxy composites filled with glass fiber and organo‐montmorillonite (OMMT) were prepared by the hand lay‐up method. The flexural properties of the epoxy/glass fiber/OMMT composites were characterized by a three‐point bending test. The flexural modulus and strength of epoxy/glass fiber were increased significantly in the presence of OMMT. The optimum loading of OMMT in the epoxy/glass fiber composites was attained at 3 wt%, where the improvement in flexural modulus and strength was approximately 66 and 95%, respectively. The fractured surface morphology of the epoxy/glass fiber/OMMT composites was investigated using field emission scanning electron microscopy. It was found that OMMT adheres on the epoxy/glass fiber interface, and this is also supported by evidence from energy dispersive X‐ray analysis. Copyright © 2007 Society of Chemical Industry     

环氧/碳纤维复合材料性能研究

本文主要分析了碳纤维帘子布复合材料的性能,并与T300单向碳纤维复合材料性能进行对比。结果表明,碳纤维帘子布复合材料性能低于T300单向碳纤维复合材料性能。     

Mechanical and morphological properties of carbon fiber reinforced–modified epoxy composites

Epoxy, prepared through aminomethyl 3,5,5‐trimethylcyclohexylamine hardening of diglycidylether of bisphenol‐A (DGEBA) prepolymer, toughened with polycarbonate (PC) in different proportions, and reinforced with carbon fiber, was investigated by differential scanning calorimetry, tensile and interlaminar shear strength testing, and scanning electron microscopy (SEM). A single glass transition temperature was found in all compositions of the epoxy/PC blend system. The tensile properties of the blend were found to be better than that of the pure epoxy matrix. They increased with PC content up to 10%, beyond which they decreased. The influence of carbon fiber orientation on the mechanical properties of the composites was studied, where the fiber content was kept constant at 68 wt %. Composites with 45° fiber orientation were found to have very weak mechanical properties, and the mechanical properties of the blend matrix composites were found to be better than those of the pure epoxy matrix composites. The fracture and surface morphologies of the composite samples were characterized by SEM. Good bonding was observed between the fiber and matrix for the blend matrix composites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3529–3536, 2006     

丁腈橡胶/铌镁锆钛酸铅/碳纤维复合材料的介电性能和压电性能

以丁腈橡胶(NBR)为基体,铌镁锆钛酸铅(PMN)粉体为分散相,碳纤维(CF)为导电填料,制备了压电复合材料,研究了复合材料的压电性能及介电性能。结果表明,80%以上PMN粒子的粒径为0.5~2.0μm,填充密度约为6.6g/cm3;当填充CF体积分数小于5%时,复合材料的击穿电压受填充CF用量的变化影响不大,当填充CF体积分数达到10%时,复合材料的击穿电压下降到未填充CF复合材料的1/3~1/2,填充CF最佳体积分数为5%;当填充PMN体积分数增至40%后,复合材料的纵向压电应变常数(d33)随PMN用量的增加而增大;适当地延长极化时间和增加极化电压有利于提高d33,最佳极化电压为7kV/mm,最佳极化时间为25min;复合材料的介电常数(ε)随填充PMN用量的增加而增大;当CF用量为0时,复合材料的ε与介电损耗(tanδ)的变化趋势相反;当填充CF体积分数为5%时,复合材料不但具有较高的ε,而且具有较高的tanδ。     

Influence of carbon fiber surface treatments on the structure and properties of conductive carbon fiber/polyethylene films

Effects of carbon fiber (CF) surface modification on the crystalline structure and both electrical and mechanical properties of conductive CF/high‐density polyethylene (HDPE) films were studied. Three different types of surface‐treated CF, epoxy‐sized, unsized, and sized but thermally treated, were considered. It was found that the uniformity of the transcrystalline zone around CF and the overall crystallinity of the polyethylene matrix decreased when epoxy‐sized CF was used. Epoxy‐sized CF caused a significant reduction not only in electrical resistivity and temperature coefficient of resistivity (TCR) but also tensile strength and coefficient of linear thermal expansion (CLTE) of composite films compared with that of unsized or sized CF that was thermally treated. We observed the systematic changes of TCR and CLTE values in accordance with CF surface modification and CF content in composite films. It was concluded that thermal expansion of the polymer matrix is the main reason for the positive TCR of CF/HDPE films. As the most probable reasons for decreased resistivity and strength of the CF/HDPE films with epoxy‐sized CF, the diffusion of epoxy sizing agent into the polyethylene matrix and the formation of loosened semiconductive interphase structure in the film are considered. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2040–2048, 2002; DOI 10.1002/app.10500     

Influence of elastomer distribution on the cryogenic microcracking of carbon fiber/epoxy composites

Carbon fiber/epoxy laminates containing three different types of rubber modifiers, separately and in combination, were developed for testing in a cryogenic environment. Preformed rubber particles, core shell rubber, and solid carboxyl‐functionalized rubber were chosen as additives to a model prepreg matrix to control the placement of the rubber within the resulting laminates. Cryogenic microcracking and mode I and II fracture toughness and interlaminar shear strength experiments were performed. Scanning electron microscopy was used to observe fracture surfaces of the rubber‐modified laminates. Fracture toughness properties were improved while the ILSS decreased because of the presence of these rubber modifiers. It was observed that the presence of these modifiers significantly reduced the microcrack density of the laminates exposed to cryogenic cycling, and in the case of one, even eliminated microcracking entirely. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2268–2275, 2003     

Effect of moisture on the thermoelectric properties in expanded graphite/carbon fiber cement composites

A kind of dry mixing and pressing process was introduced to prepare expanded graphite/carbon fiber cement composites (EG-CFRC). Significant effect of moisture on the thermoelectric properties of EG-CFRC was observed. The higher the moisture content is, the greater the absolute Seebeck coefficient. The maximum of absolute Seebeck coefficient 11.59 μV/°C was obtained with moisture of 14.98% at 33 °C. Simultaneously, the maximum of electrical conductivity 0.78 S cm⁻¹ was got with moisture of 11.44%. Furthermore, the largest power factor 7.85×10⁻⁴ µW m⁻¹ K⁻² was calculated at 33 °C with moisture of 11.44%. The carrier scattering, polarization effects and high density defects interface of EG-CFRC are attributed to the enhancement of thermoelectric properties in the case of higher moisture content.     

Effect of adding carbon fiber on conductive stability of acrylonitrile‐butadiene rubber composites

In this work, the conductive composites of acrylonitrile‐butadiene rubber (NBR) and conductive carbon black (CCB) were prepared. The volume resistivity of NBR/CCB composites became stable when the addition content of CCB reached 12 wt %. However, when carbon fiber (CF) was added into the composites, the volume resistivity of NBR/CCB/CF composites continued to decrease with the increase of CF addition, which resulted from the formation of the three‐dimensional conductive network in composite matrix. In addition, the effect of acid oxidation of CF surface on the mechanical proprieties and conductive stability of NBR/CCB/CF composites was studied. The results indicated the acid oxidation of CF surface improved the bond structure between NBR and CF, which further decreased the resistance and significantly improved the mechanical properties of the composites. It was demonstrated that the conductive stability of NBR composites after cyclic mechanical and temperature fatigues was remarkably enhanced with the addition of CF. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46668.     

Enhanced interfacial strength and mechanical properties of carbon fiber composites by introducing functionalized silica nanoparticles into the interface

Introducing nanoparticles onto the surface of carbon fibers (CFs) is a useful method for enhancing the quality of fiber-matrix interface. In this work, a liquid sizing agent containing functionalized silica nanoparticles (SiO₂) was well prepared to improve interfacial strength and mechanical properties of composites. In order to enhance the dispersion of SiO₂ nanoparticles in sizing agent, SiO₂ nanoparticles were chemically grafted with 3-aminopropyltriethoxysilane (APS), and then silanized silica (SiO₂-APS) was introduced into the interphase by a conventional sizing process as well. Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and thermogravimetric analysis (TGA) confirmed the successful preparation of SiO₂-APS. Scanning electron microscopy (SEM) showed that a uniform distribution of SiO₂-APS on the fiber surface and the increased surface roughness. The sized fibers (CF/SiO₂-APS) exhibited a high surface free energy and good wettability based on a dynamic contact angle testing. Interfacial microstructure and mechanical properties of untreated and sized CFs composites were investigated. Simultaneous enhancements of interlaminar shear strength (ILSS) and impact toughness of CF/SiO₂-APS composites were achieved, increasing 44.79% in ILSS and 31.53% in impact toughness compared to those of untreated composites. Moreover, flexural strength and modulus of composites increased by 32.22 and 50.0% according to flexural test. In addition, the hydrothermal aging resistance of CF/SiO₂-APS composites has been improved significantly owing to the introduced Si-O-Si bonds at the interface.     

Effect of nanosized carbon black on the morphology,transport, and mechanical properties of rubbery epoxy and silicone composites

Three different types of nanosized carbon black (CB), Printex XE2 (CBP), Vulcan XC72, and Printex 140 U (CBU), were dispersed by mechanical mixing in rubbery epoxy (RE) and silicone to produce composites. It was found that the maximum possible loading of CB in the polymers depended on the surface area of CB. For a given loading, all three CBs produced similar improvements in the thermal conductivity of the resulting composites, but their effects on the electrical conductivity varied and ranged from insulating composites with CBU to conducting composites with CBP. CBP produced a greater improvement in the electrical conductivity than the thermal conductivity of the polymers compared to the other CBs. This was attributed to the high structure of CBP, which led to the formation of a concatenated structure within the matrix. The CB/silicone composites had a similar thermal conductivity to that of the CB/RE composites, but only the CBP/silicone composite produced at 8 wt % loading was electrically conducting. The compression and hardness properties of RE were also significantly improved with the addition of CB. However, in the case of silicone, only CBP had a considerable effect on the compression properties. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Mechanical properties of carbon fiber composites modified with nano-SiO2 in the interphase

The performance of carbon fibers-reinforced composites is dependent to a great extent on the properties of fiber–matrix interface. To improve the interfacial properties in carbon fibers/epoxy composites, nano-SiO₂ particles were introduced to the surface of carbon fibers by sizing treatment. Atomic force microscope (AFM) results showed that nano-SiO₂ particles had been introduced on the surface of carbon fibers and increase the surface roughness of carbon fibers. X-ray photoelectron spectroscopy (XPS) showed that nano-SiO₂ particles increased the content of oxygen-containing groups on carbon fibers surface. Single fiber pull-out test (IFSS) and short-beam bending test (ILSS) results showed that the IFSS and ILSS of carbon fibers/epoxy composites could obtain 30.8 and 10.6% improvement compared with the composites without nano-SiO₂, respectively, when the nano-SiO₂ content was 1 wt % in sizing agents. Impact test of carbon fibers/epoxy composites treated by nano-SiO₂ containing sizing showed higher absorption energy than that of carbon fibers/epoxy composites treated by sizing agent without nano-SiO₂. Scanning electron microscopy (SEM) of impact fracture surface showed that the interfacial adhesion between fibers and matrix was improved after nano-SiO₂-modified sizing treatment. Dynamic mechanical thermal analysis (DMTA) showed that the introduction of nano-SiO₂ to carbon fibers surface effectively improved the storage modulus of carbon fibers/epoxy.     

Effect of fiber treatment on the mechanical properties of LDPE-henequen cellulosic fiber composites

The degree of mechanical reinforcement that could be obtained by the introduction of henequen cellulosic fibers in a low-density polyethylene, LDPE, matrix was assessed experimentally. Composite materials of LDPE-henequen cellulosic fibers were prepared by mechanical mixing. The concentration of randomly oriented fibers in the composite ranged between 0 and 30% by volume. The tensile strength of these composite materials increased up to 50% compared to that of LDPE. There is also a noticeable increase in Young's modulus for the composite materials that compares favorably with that of LDPE. As expected, the addition of the fibers decreases the ultimate strain values for the composite materials. The thermal behavior of the LDPE-henequen cellulosic fibers materials, studied by differential scanning calorimetry, DSC, showed that the presence of the fibers does not affect the thermal behavior of the LDPE matrix; thus, the interaction between fiber and matrix is probably not very intimate. Preimpregnation of the cellulosic fibers in a LDPE-xylene solution and the use of a silane coupling agent results in a small increment in the mechanical properties of the composites, which is attributed to an improvement in the interface between the fibers and the matrix. The shear properties of the composites also increased with increasing fiber content and fiber surface treatment. It was also noted that the fiber surface treatment improves fiber dispersion in the matrix. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 197–207, 1997     

石墨烯改性对环氧树脂/碳纤维复丝拉伸性能的影响

采用直接分散法和上浆剂法分别制备了环氧树脂/碳纤维复丝,通过红外光谱、分光光度法等分析方法对处理的石墨烯的表面官能团及表面形貌进行表征,借助扫描电子显微镜对碳纤维表面进行微观形貌观察,研究了石墨烯改性对环氧树脂/碳纤维复丝界面性能的影响。结果表明:石墨烯表面成功地接枝了硅烷偶联剂KH-560;接枝硅烷偶联剂KH-560的石墨烯的环氧树脂/碳纤维复丝的拉伸性能优于未经改性的石墨烯的复丝;上浆法制得的环氧树脂/碳纤维复丝的拉伸性能优于分散法制得的复丝的拉伸性能;上浆剂法制备的石墨烯改性的环氧树脂/碳纤维复丝的断裂强力比未经过改性的未上浆的复丝的提高了48.6%,拉伸强度提高了30.4%,断裂伸长率提高了90.9%。     

Influence of alkali fiber treatment and fiber processing on the mechanical properties of hemp/epoxy composites

Industrial hemp fibers were treated with a 5 wt % NaOH, 2 wt % Na₂SO₃ solution at 120°C for 60 min to remove noncellulosic fiber components. Analysis of fibers by lignin analysis, scanning electron microscopy (SEM), zeta potential, Fourier transform infrared (FTIR) spectroscopy, wide angle X‐ray diffraction (WAXRD) and differential thermal/thermogravimetric analysis (DTA/TGA), supported that alkali treatment had (i) removed lignin, (ii) separated fibers from their fiber bundles, (iii) exposed cellulose hydroxyl groups, (iv) made the fiber surface cleaner, and (v) enhanced thermal stability of the fibers by increasing cellulose crystallinity through better packing of cellulose chains. Untreated and alkali treated short (random and aligned) and long (aligned) hemp fiber/epoxy composites were produced with fiber contents between 40 and 65 wt %. Although alkali treatment generally improved composite strength, better strength at high fiber contents for long fiber composites was achieved with untreated fiber, which appeared to be due to less fiber/fiber contact between alkali treated fibers. Composites with 65 wt % untreated, long aligned fiber were the strongest with a tensile strength (TS) of 165 MPa, Young's modulus (YM) of 17 GPa, flexural strength of 180 MPa, flexural modulus of 9 GPa, impact energy (IE) of 14.5 kJ/m², and fracture toughness (K_Ic) of 5 MPa m^1/2. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synergistic modification of carbon fiber by electrochemical oxidation and sizing treatment and its effect on the mechanical properties of carbon fiber reinforced composites

In this article, The CF surface was modified by the synergistic modification of electrochemical oxidation and sizing treatment. Firstly, the electrochemical oxidation was carried out using fatty alcohol polyoxyethylene ether phosphate (AEOPK) as the electrolyte. The content of active groups on the modified CF surface increased by 235%. However, the strength of CF monofilament decreased due to the etching. Then, the electrochemically oxidized CFs were sized with the phosphate modified epoxy resin (PAEK). The etched defects on CF surface caused by the electrochemical oxidation were repaired by sizing agent molecules according to the AFM results. Furthermore, the spreadability of PAEK emulsion on the CF surface, the content of CF surface groups and the interaction of CFRC were characterized by using the monofilament contact angle, XPS and Raman spectroscopy. The results suggested that the synergistic modification could improve the CF surface activity, facilitate the spreading of PAEK on the CF surface, and increase the interaction between the CFs and the resin matrix. There were 20.3 and 22.6% enhancement in the breaking strength and elongation of CF monofilament. In addition, the interlaminar shear strength (ILSS) of CFRC prepared with synergistically modified CFs was increased from 12.81 to 33.04 MPa. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48028.     

溶聚丁苯橡胶/炭黑/短纤维复合材料的取向结构与力学性能

研究了溶聚丁苯橡胶(SSBR)／炭黑／短纤维复合材料(SFRC)的力学性能和短纤维在橡胶中的取向度及其黏合效果,分析了短纤维的黏合作用对复合材料应力．应变形为的影响。结果表明,短纤维的加入显著提高了SFRC的撕裂强度、10％定伸应力及邵尔A型硬度;短纤维用量小于30份时。2种预处理短纤维的取向度呈增长趋势,且尼龙短纤维的取向度明显高于聚酯短纤维;SFRC在平行方向上有不同程度的屈服现象,且添加聚酯短纤维的SFRC屈服应变及应力值小于添加尼龙短纤维的SFRC。SFRC在垂直方向没有应力屈服现象;预处理短纤维与橡胶的黏合效果优于未处理短纤维。     

短切碳纤维及碳纤维布增强硅橡胶复合材料的制备及力学性能

将短切碳纤维(CF)、白炭黑和甲基乙烯基硅橡胶(VMQ)共混后,与碳纤维布(CFC)复合制备VMQ复合材料.考察了CFC层数对复合材料的拉伸性能、邵尔A硬度、耐磨性能及动态力学性能的影响.结果表明,随着CFC层数的增加,复合材料的扯断伸长率基本不变,拉伸强度逐渐升高.与仅添加10份(质量,下同)CF的复合材料相比,加入...