Poly(acrylic acid)/poly(acrylamide) hydrogel adsorbent for removing methylene blue

Cationic dye can cause severe damage to the environment due to their refractory degradation, complex composition and strong stability. Hydrogels as adsorbents have been widely used to treatment the wastewater with dyestuff for their low prices, simple operations, and high efficiency. This work uses poly(acrylic acid) (PAA)/poly(acrylamide)(PAM)/calcium hydroxide nanoparticles (CHN) polymeric hydrogel absorbent to eliminate methylene blue (MB) dye. First, PAM/PAA/CHN hydrogel is produced through copolymerization of acrylic acid monomer and acrylamide monomer using inorganic CHN as cross-linker. And then, the adsorption performance of such PAM/PAA/CHN hydrogel adsorbent for adsorbing MB dye is explored at different conditions including pH, contacting time, adsorbent dosage, initial concentration of MB, and temperature. A maximum adsorption capability for adsorbing MB reaches 1,056 mg/g. Furthermore, the pseudo-first-order mode and Langmuir isotherm model can well describe adsorption behavior of MB dye onto such PAA/PAM/CHN hydrogel adsorbent. Thereby, as-prepared PAA/PAM/CHN hydrogel could be a potential adsorbent for eliminating organic dyes from wastewater.     

Removal of methylene blue from aqueous solution by adsorption onto zeolite synthesized from coal fly ash and its thermal regeneration

BACKGROUND: The removal of cationic dyes from wastewater is of great importance. Three zeolites synthesized from coal fly ashes (ZFAs) were investigated as adsorbents to remove methylene blue (MB), a cationic dye, from aqueous solutions. Experiments were conducted using the batch adsorption technique under different conditions of initial dye concentration, adsorbent dose, solution pH, and salt concentration. RESULTS: The adsorption isotherm data of MB on ZFAs were fitted well to the Langmuir model. The maximum adsorption capacities of MB by the three ZFAs, calculated using the Langmuir equation, ranged from 23.70 to 50.51 mg g^?1. The adsorption of MB by ZFA was essentially due to electrostatic forces. The measurement of zeta potential indicated that ZFA had a lower surface charge at alkaline pH, resulting in enhanced removal of MB with increasing pH. MB was highly competitive compared with Na⁺, leading to only a < 6% reduction in adsorption in the presence of NaCl up to 1.0 mol L^?1. Regeneration of used ZFA was achieved by thermal treatment. In this study, 90–105% adsorption capacity of fresh ZFA was recovered by heating at 450 °C for 2 h. CONCLUSION: The experimental results suggest that ZFA could be employed as an adsorbent in the removal of cationic dyes from wastewater, and the adsorptive ability of used ZFA can be recovered by thermal treatment. Copyright © 2010 Society of Chemical Industry     

Radiation-initiated chitosan-based double network hydrogel: Synthesis,characterization, and adsorption of methylene blue

A novel chitosan (CTS)-based double network Poly(2-acrylaMido-2-Methyl-1-propanesulfonic acid)/Polyacrylamide/CTS hydrogel was synthesized by irradiation initiated. Laponite RD (RD) was used as both dopant and the cross-linking agent. Then the fabricated hydrogel was applied as an efficient adsorbent to remove the methylene blue (MB) in an aqueous solution. This hydrogel has both high strength and good adsorption properties for MB. The results from Brunauer–Emmett–Teller method confirmed that the hydrogel has a large specific surface area (96 m²/g) and developed pore structure, which is available for the contact between the adsorbent and dye molecules. In the adsorption process, the RD provides plenty of negative charges as adsorption sites for MB molecules. The influence of pH, temperature, and adsorbent dose on the adsorption performance was investigated in detail. The experimental data fit well with the pseudo-second-order kinetic model and Langmuir isotherm. Besides, the mechanical strength of the hydrogel was also investigated in this work.     

From pollutant to solution of wastewater pollution: Synthesis of activated carbon from textile sludge for dye adsorption

Adsorption is an important process in wastewater treatment,and conversion of waste materials to adsorbent offers a solution to high material cost related to the use of commercial activated carbon.This study investigated the adsorption behaviour of Reactive Black 5(RB5)and methylene blue(MB)onto activated carbon produced from textile sludge(TSAC).The activated carbon was synthesized through chemical activation of precursor followed with carbonization at 650°C under nitrogen flow.Effects of time(0–200 min),pH(2–10),temperature(25–60°C),initial dye concentration(0–200 mg·L~(-1)),and adsorbent dosage(0.01–0.15 g)on dye removal efficiency were investigated.Preliminary screening revealed that TSAC synthesized via H_2SO_4activation showed higher adsorption behaviour than TSAC activated by KCl and ZnCl_2.The adsorption capacity of TSAC was found to be 11.98 mg·g~(-1)(RB5)and 13.27 mg·g~(-1)(MB),and is dependent on adsorption time and initial dye concentration.The adsorption data for both dyes were well fitted to Freundlich isotherm model which explains the heterogeneous nature of TSAC surface.The dye adsorption obeyed pseudo-second order kinetic model,thus chemisorption was the controlling step.This study reveals potential of textile sludge in removal of dyes from aqueous solution,and further studies are required to establish the applicability of the synthesized adsorbent for the treatment of waste water containing toxic dyes from textile industry.     

Synthesis of an ordered mesoporous carbon with graphitic characteristics and its application for dye adsorption

An ordered mesoporous carbon (OMC) was prepared by a chemical vapor deposition technique using liquid petroleum gas (LPG) as the carbon source. During synthesis, LPG was effectively adsorbed in the ordered mesopores of SBA-15 silica and converted to a graphitic carbon at 800 °C. X-ray diffraction and nitrogen adsorption/desorption data and high-resolution transmission electron microscopy (HRTEM) of the OMC confirmed its ordered mesoporous structure. The OMC was utilized as an adsorbent in the removal of dyes from aqueous solution. A commercial powder activated carbon (AC) was also investigated to obtain comparative data. The efficiency of the OMC for dye adsorption was tested using acidic dye acid orange 8 (AO8) and basic dyes methylene blue (MB) and rhodamine B (RB). The results show that adsorption was affected by the molecular size of the dye, the textural properties of carbon adsorbent and surface-dye interactions. The adsorption capacities of the OMC for acid orange 8 (AO8), methylene blue (MB) and rhodamine B (RB) were determined to be 222, 833, and 233 mg/g, respectively. The adsorption capacities of the AC for AO8, MB, and RB were determined to be 141, 313, and 185 mg/g, respectively. The OMC demonstrated to be an excellent adsorbent for the removal of MB from wastewater.     

Swelling and dye adsorption study of novel superswelling [Acrylamide/N-vinylpyrrolidone/3(2-hydroxyethyl carbamoyl) acrylic acid] hydrogels

Summary Super swelling acrylamide (Am)/N-vinylpyrrolidone (NVP)/3-(2-hydroxyethyl carbamoyl) acrylic acid (HECA) hydrogels were prepared by free radical polymerization of quaternary mixtures of Am, NVP, HECA and water. The hydrogels were used in experiments on swelling, diffusion and adsorption of some water-soluble monovalent cationic dyes such as Crystal Violet (CV), Malachite Green (MG) and Methylene Blue (MB). In the experiment of the adsorption of dyes from their aqueous solutions type-S adsorption isotherm were found. The diffusion of water within the hydrogel was found to have non Fickian character. The uptake of dyes within the hydrogel increased in the following order: MG > MB > CV. The binding ratio of the hydrogel/dye systems was gradually increased with the increase of HECA content in the AAm/NVP/HECA hydrogel.     

Removal of Methylene Blue from Aqueous Solutions by using Cold Plasma,Microwave Radiation and Formaldehyde Treated Acorn Shell

In this paper, cold plasma (CPTAS), formaldehyde (FTAS), and microwave radiation treated (MTAS) acorn shell obtained from Quercus petraea tree as biosorbent was characterized and its dye removal ability at different dye concentrations was studied. The isoelectric point, functional groups and morphology of acorn shell was investigated as adsorbent surface characteristics. Fourier transform infrared (FTIR), scanning electron microscopy (SEM), and UV–Vis spectrophotometry were used. Methylene blue (MB) was used as model cationic dye. The Langmuir and Freundlich adsorption isotherm models were applied to describe the equilibrium isotherms. The results indicated that the data for adsorption of MB onto treated acorn shell fitted well with the Langmuir isotherm model. Comparison of adsorption capacities of CPTAS with FTAS has shown a significant increase by as much as about 30 mg/g (33.32%) in MB adsorption.The pseudo-first order, pseudo-second order kinetic models were examined to evaluate the kinetic data, and the rate constants were calculated. Adsorption kinetic of dyes followed pseudo-first order kinetics. Thermodynamic parameters such as free energy, enthalpy, and entropy of dye adsorption were obtained. The results indicated that acorn shell could be used as a natural biosorbent for the removal of cationic dyes.     

The removal of cationic dyes from aqueous solutions by adsorption onto pistachio hull waste

The efficacy of pistachio hull powder (PHP) prepared from agricultural waste was investigated in this study as a novel adsorbent for the elimination of dye molecules from contaminated streams. Removal of methylene blue (MB) as a cationic model dye by PHP from aqueous solution was studied under different experimental conditions. The selected parameters were solution pH (2–10), PHP dosage (0.5–3 g/L), MB concentrations (100–400 mg/L), contact time (1–70), and solution temperature (20–50 °C). The experimental results indicated that the maximum MB removal could be attained at a solution pH of 8. The dosage of PHP was also found to be an important variable influencing the MB removal percentage. The removal efficiency of MB improved from 94.6 to 99.7% at 70 min contact time when the MB concentration was decreased from 300 to 100 mg/L at a pH and PHP dosage of 8 and 1.5 g/L, respectively. The kinetic analysis showed that the pseudo-second-order model had the best fit to the experimental data. The Langmuir equation provided the best fit for the experimental data of the equilibrium adsorption of MB onto PHP at different temperatures. In addition, the maximum adsorption capacity increased from 389 to 602 mg/g when the temperature was increased from 20 to 50 °C. The thermodynamic evaluation of MB adsorption on PHP revealed that the adsorption phenomenon under the selected conditions was a spontaneous physical process. Accordingly, pistachio hull waste was shown to be a very efficient and low-cost adsorbent, and a promising alternative for eliminating dyes from industrial wastewaters.     

Poly(acrylamide/laponite) nanocomposite hydrogels: Swelling and cationic dye adsorption properties

Super adsorbent polyacrylamide (PAAm)/nanoclay (laponite, Lap) hydrogels were prepared by in situ free radical polymerization of AAm in an aqueous solution with clay as a crosslinker. The swelling properties and water‐soluble cationic dye adsorption behaviors of the PAAm/laponite (PAAm/Lap) nanocomposite (NC) hydrogels were investigated. The parameters of swelling and diffusion of water in dye solutions were evaluated for the PAAm/Lap NC hydrogels. The adsorption behavior of the monovalent cationic dyes such as Basic Blue 12 (BB 12), Basic Blue 9 (BB 9), and Basic Violet 1 (BV 1), were studied on the NC hydrogels. The effects of the clay content of the hydrogel on its cationic dye uptake behavior were studied. The adsorption studies indicated that the rates of dye uptake by the NC hydrogels increased in the following order: BB 9 > BB 12 > BV 1. This order is similar to the swelling results of the PAAm/Lap NC hydrogel in the dye solutions. The equilibrium uptakes of the different dyes by the PAAm/Lap NC hydrogel were nearly the same. In the dye absorption studies, S‐type adsorption in the Giles classification system was found for the BB 12 and BV 1 dyes, whereas L ‐type was observed for the BB 9 dye. After the heat treatment of PAAm/Lap, the rate of dye uptake and equilibrium dye uptake were increased. The NC hydrogels may be considered as a good candidate for environmental applications to retain more water and to remove dyes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Adsorption behavior of cationic dyes on citric acid esterifying wheat straw: kinetic and thermodynamic profile

The kinetic and thermodynamic behaviors of cationic dye adsorption onto citric acid esterifying wheat straw (EWS) from aqueous solution were investigated. Two cationic dyes, methylene blue (MB) and crystal violet (CV) were selected as adsorbates. The kinetic and thermodynamic parameters of dye adsorption were examined with a batch system by changing various experimental factors (e.g. initial pH, EWS dosage, dye concentration, contact time, temperature). The MB and CV removal ratios came up to the maximum value beyond pH 4. The 2.0 g/L or up of EWS could almost completely remove MB and CV from 250 mg/L of dye solution. The adsorption percentages of MB and CV kept above 95% over a range from 50 to 350 mg/L of dye concentration when 2.0 g/L of EWS was used. The isothermal data followed the Langmuir model. The adsorption processes could be described by the pseudosecond-order kinetic model. The dual linear plots of intraparticle diffusion indicated that two intraparticle diffusion steps occurred in the dye adsorption processes. The thermodynamic study indicated that the adsorptions of dyes were spontaneous and endothermic. High temperatures favored the adsorption processes.     

Removal of methylene blue from aqueous solution by sorption on lignocellulose-g-poly(acrylic acid)/montmorillonite three-dimensional cross-linked polymeric network hydrogels

Batch lignocellulose-g-poly(acrylic acid)/montmorillonite (LNC-g-PAA/MMT) hydrogel nanocomposites were applied as adsorbents. The nanocomposites were characterized by FTIR, XRD, SEM, and TEM. The results showed that montmorillonite (MMT) could react with the monomers and change the structure of polymeric network of the traditional superabsorbent materials, an exfoliated structure was formed in the nanocomposites. The effect of process parameters such as MMT content (wt%), contact time (t), initial concentration of dye solution (C ₀), adsorption temperature (T), and pH value (pH) of the dye solution for the removal of methylene blue (MB) from aqueous solution were also studied. The results showed that the adsorption capacity for MB increased with increasing contact time, initial dye concentration, and pH value, but decreased with increasing MMT content and temperature. The adsorption kinetics were better described by the pseudo-second-order equation, and their adsorption isotherms were better fitted for the langmuir equation. By introducing 20 wt% MMT into LNC-g-PAA polymeric network, the obtaining hydrogel composite showed the high adsorption capacity 1994.38 mg/g and economic advantage for MB. The desorption studies revealed that the composite provided the potential for regeneration and reuse after MB dye adsorption, which implied that the composite could be regarded as a potential adsorbent for cationic dye MB removal in a wastewater treatment process.     

Chitosan/polyaniline hybrid for the removal of cationic and anionic dyes from aqueous solutions

Nanostructured chitosan/polyaniline (CH/PANI) hybrid was synthesized via in situ polymerization of aniline in the presence of chitosan. The CH/PANI hybrid was characterized by FTIR spectroscopy, X-ray diffraction, thermogravimetric analysis, and scanning electron microscopy. The CH/PANI hybrid had a nanofibrous structure with an average diameter of 70 nm. This hybrid was employed as an ecofriendly and efficient adsorbent with high adsorption capacity for the removal of Acid Green 25 (AG) and methylene blue (MB) from aqueous solutions. AG and MB were used as anionic and cationic model dyes, respectively. The CH/PANI adsorbent showed high dependence on the pH of the medium with an excellent adsorption performance and regeneration manner. The kinetics and adsorption isotherms were studied. The CH/PANI hybrid follows the pseudo second-order adsorption kinetics and Temkin isotherm model for the adsorption of both AG and MB dyes. This assumes that the enthalpy of dyes molecules decreases with the adsorption on heterogeneous surface with various kinds of adsorption sites and as well as the ability to form multilayers of the dye. Also, intraparticle diffusion was found to play an important role in the adsorption mechanism. The maximum adsorption capacity was found to be 240.4 mg g⁻¹ of AG at pH 4 and 81.3 mg g⁻¹ of MB at pH 11. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47056.     

Application of succinylated sugarcane bagasse as adsorbent to remove methylene blue and gentian violet from aqueous solutions - Kinetic and equilibrium studies

In a previous work, succinylated sugarcane bagasse (SCB 2) was prepared from sugarcane bagasse (B) using succinic anhydride as modifying agent. In this work the adsorption of cationic dyes onto SCB 2 from aqueous solutions was investigated. Methylene blue, MB, and gentian violet, GV, were selected as adsorbates. The capacity of SCB 2 to adsorb MB and GV from aqueous single dye solutions was evaluated at different contact times, pH, and initial adsorbent concentration. According to the obtained results, the adsorption processes could be described by the pseudo-second-order kinetic model. Adsorption isotherms were well fitted by Langmuir model. Maximum adsorption capacities for MB and GV onto SCB 2 were found to be 478.5 and 1273.2 mg/g, respectively.     

Polymer‐derived ceramic adsorbent for pollutant removal from water

Polymer‐derived ceramic components (SiOC, sample W) were produced from preceramic polymer mixture and a catalyst. After curing and pyrolysis, some of the samples etched by hydrofluoric acid to obtain carbonaceous SiOC (C‐rich SiOC, sample W‐HF). W and W‐HF were tested as an adsorbent material to remove both heavy‐metal ions (Cr (III), Pb (III), and Cd (II)) and cationic dyes (Methylene Blue (MB), Rhodamine B (RB), and Crystal Violet (CV)) from aqueous solutions. HF‐treated high surface area SiOC samples had quite high adsorption affinity for cationic dyes. According the Langmuir isotherm model the maximum dye uptake values were found to be around to 50 mg/g for sample W, whereas those for sample W‐HF ranged from 104 to 186 mg/g. Regeneration studies were conducted both by heat treatment and leaching, high recovery yields (always above 97%) of MB adsorption were obtained.     

Enhancing the adsorption affinity of cellulose acetate film toward cationic dye by incorporating Cloisite 30B grafted with polyacrylic acid

Cellulose acetate (CA) is known for its low adsorption affinity toward dyes, hence this study aims to improve its adsorption affinity toward cationic dyes by introducing Cloisite 30B grafted with polyacrylic acid (C30B-g-PAA). C30B-g-PAA was synthesized by grafting polyacrylic acid (PAA) onto Cloisite 30B (C30B) using in-situ reversible addition fragmentation chain transfer (RAFT) polymerization. Different weight ratios of unmodified (raw) and modified (C30B-g-PAA) C30B (0, 25, and 50 wt%) were incorporated into CA matrices to prepare a series of CA nanocomposite films. The results showed that the adsorption affinity of the prepared nanocomposite films increased toward cationic methylene blue (MB) dye with incorporating either unmodified or modified C30B, but a significant improvement was observed with the incorporating C30B-g-PAA with a maximum adsorption capacity of 53 mg/g for a load of 50 wt%. This indicates that the surface modification of C30B with PAA was effective in enhancing the adsorption efficacy of CA. The kinetic and isotherm studies showed that the adsorption behavior of CA nanocomposite film with 50 wt% of C30B-g-PAA followed pseudo-second-order and Langmuir isothermal model. Regeneration study showed good reusability of CA nanocomposite film with 50 wt% of C30B-g-PAA. These results demonstrate that the nanocomposite film with 50 wt% of C30B-g-PAA can be used as a highly efficient, easy to separate, and reusable adsorbent material to remove MB dye from wastewater.     

Hyperbranched polyglycerol/poly(acrylic acid) hydrogel for the efficient removal of methyl violet from aqueous solutions

Hydrogels were synthesized from hyperbranched polyglycerol (HPG) and acrylic acid through free‐radical polymerization with HPG as the crosslinker. The HPG/poly(acrylic acid) (PAA) hydrogel could absorb cationic dyes in aqueous solutions because of the existence of a porous structure and the large numbers of hydroxyl and carboxylic groups. With methyl violet chosen as a model compound, the HPG/PAA hydrogel reached a maximum adsorption of 394.12 mg/g at a feed concentration of 1 g/L. The highest removal ratio of 98.33% was observed at a feed concentration of 50 mg/L. The effects of the pH, contact time, and feed concentration on the dye adsorption were investigated. The dye adsorption data fit well with the pseudo‐second‐order and Langmuir models. We believe that the HPG/PAA hydrogels could perform well in appropriate applications in the removal of cationic dyes from aqueous solutions because of their high adsorption capacity and environmental friendliness. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42951.     

Effect of bis[2-(methacryloyloxy)ethyl] phosphate as a crosslinker on poly(AAm-co-AMPS)/Na-MMT hydrogel nanocomposite as potential adsorbent for dyes: kinetic,isotherm and thermodynamic study

In the present study, synthesis of poly(AAm-co-AMPS)/Na-MMT hydrogel nanocomposite with different amount of bis[2-(methacryloyloxy)ethyl] phosphate as a crosslinker was successfully carried out for the removal of crystal violet (CV), methylene blue (MB) and methyl red (MR) from aqueous solution. Hydrogel nanocomposite was characterized by FT-IR, SEM, EDS, XRD and TGA analysis. Several important parameters were investigated to obtain maximum adsorption capacity. Adsorption behavior of hydrogel nanocomposite was investigated for the adsorption of dyes and it was found to remove about 80% for CV, 89% for MB and 51% for MR in 50 mg/L of dyes solutions at pH 7 and about 86% for CV, 93% for MB and 23% for MR at pH 12. Kinetic studies revealed that the applicability of pseudo-first-order and pseudo-second-order model for the adsorption of CV, MB and MR. The adsorption isotherm was studied in 25, 35, 45 and 55 °C using Langmuir, Freundlich, Temkin and Jovanovic models and the adsorption data were well described by Freundlich isotherm model. Hydrogel nanocomposite showed 155, 176 and 113 mg/g maximum adsorption capacity for CV, MB and MR respectively. Negative values of ΔG⁰ for all three dyes suggested the feasibility of dyes removal and support for spontaneous adsorption of CV, MB and MR on hydrogel nanocomposite. Desorption of dyes from the dye loaded hydrogel nanocomposite was simply done in ethanol. The results indicate that the prepared poly(AAm-co-AMPS)/Na-MMT hydrogel nanocomposite is an efficient adsorbent with high adsorption capacity for the aforementioned dyes.

Open image in new window

Graphical abstract Graphical abstract illustrating the preparation and dye adsorption processes of the poly(AAm-co-AMPS)/Na-MMT hydrogel nanocomposite

     

ZnO/Cassava Starch-Based Hydrogel Composite for Effective Treatment of Dye-Contaminated Wastewater

Industrial expansion has increased the discharge of contaminated wastewater. Wastewater can be treated by adsorption with petroleum-based hydrogels but the materials are not biodegradable and therefore cause secondary toxic waste. In this work, hydrogel composites are prepared based on non-biodegradable polyacrylamide and biodegradable materials of cassava starch (CS) and poly(vinyl alcohol). The effect of CS content on the porous structure is studied. The highest water absorption capacity of 74 g g⁻¹ is obtained from a hydrogel 30 wt% of CS. Within 4 h, the hydrogel effectively adsorbs the cationic dyes methylene blue (MB) and crystal violet, and the anionic dyes congo red and reactive orange. The maximum adsorption capacity toward MB is 993 mg g⁻¹. Experimental data indicate a monolayer adsorption via chemisorption. Silica-coated ZnO photocatalyst particles are synthesized via a sol–gel method and coated on the outer surface of the hydrogel. Under sunlight, the hydrogel composite degrades almost 90% of adsorbed dye. The hydrogel composite is capable of effective photodegradation for at least three cycles under artificial UV irradiation and four cycles under sunlight, but adsorption capacity remains higher than 80% at the eighth cycle. The hydrogel composite also shows antibacterial activities, indicating an additional beneficial property for industrial wastewater treatment.     

Adsorption Behavior of Methylene Blue from Aqueous Solution by the Hydrogel Composites Based on Attapulgite

A series of carboxymethyl cellulose-g-poly (acrylic acid)/attapulgite hydrogel composites were synthesized for the removal of cationic dye methylene blue. Various factors affecting the uptake behavior were investigated. Adsorption rate of the hydrogel was quite fast, and adsorption equilibrium could be reached within 30 min. Adsorption kinetics well followed the pseudo-second-order equation for all systems. The Langmuir isotherm was found to best represent the data for the dye uptake. Even when 20 wt% attapulgite was introduced into the hydrogel, the corresponding maximum adsorption capacity reached 1979.48 mg/g at 30°C. The as-prepared adsorbents exhibited excellent affinity for the dye, and can be applied to treat wastewater containing basic dyes.     

VMT/P(AMPS-co-AA)复合高吸水树脂的性能测试

研究了溶液pH、盐浓度对辉光放电电解等离子体引发合成的蛭石/聚(2-丙烯酰胺-2-甲基丙磺酸-co-丙烯酸) (VMT/P(AMPS-co-AA)) 复合高吸水树脂的溶胀行为的影响,考察了染料pH、吸附时间、染料浓度等因素对复合高吸水树脂吸附量的影响,同时对树脂的吸附-解吸性能进行了研究。结果表明, VMT/P(AMPS-co-AA)具有高吸水性、pH敏感性、盐敏感性以及高吸附性。该树脂在蒸馏水中的最大溶胀率达到822.4 g/g,对阳离子染料亚甲基蓝(MB)、结晶紫(CV)和孔雀石绿(MG)的吸附量分别可达2027.8, 2171.8和883.2 mg/g。在pH=6.5和25℃下,其对染料的吸附行为符合动力学准二级模型,该树脂还具有一定的吸附-解吸性能和重复利用性能。