Influence of UV-laser radiation on the synthesis of DLC films by ECR-plasma-CVD

Simultaneous UV-laser irradiation during the deposition of DLC films has been found to significantly influence the growth process and to favourably modify the film properties. The influence of the spectral and energetic parameters of laser radiation was investigated with respect to the optical, structural and mechanical properties of DLC films. Detailed investigations on the mechanism of laser-induced structural transformations in DLC films are presented, as studied by Raman spectroscopy. Further, the characteristic peak for the nanocrystalline diamond phase at 1140 cm⁻¹ was evident for irradiated films. Noteworthy is the increase in film microhardness with increasing energy of the deposited carbon ions with a simultaneous reduction in internal stresses, caused by photolytically induced modification of the film structure by UV-laser radiation. As a result, hard (up to 30 GPa) and thick (up to 3 μm) defect-free DLC films without cracks have been synthesized.     

Preparation of diamond like carbon thin films above room temperature and their properties

Diamond like carbon (DLC) thin films were deposited on p-type silicon (p-Si), quartz and ITO substrates by microwave (MW) surface-wave plasma (SWP) chemical vapor deposition (CVD) at different substrate temperatures (RT ∼ 300 °C). Argon (Ar: 200 sccm) was used as carrier gas while acetylene (C₂H₂: 20 sccm) and nitrogen (N: 5 sccm) were used as plasma source. Analytical methods such as X-ray photoelectron spectroscopy (XPS), FT-IR and UV–visible spectroscopy were employed to investigate the structural and optical properties of the DLC thin films respectively. FT-IR spectra show the structural modification of the DLC thin films with substrate temperatures showing the distinct peak around 3350 cm^− 1 wave number; which may corresponds to the sp² C–H bond. Tauc optical gap and film thickness both decreased with increasing substrate temperature. The peaks of XPS core level C 1 s spectra of the DLC thin films shifted towards lower binding energy with substrate temperature. We also got the small photoconductivity action of the film deposited at 300 °C on ITO substrate.     

Synthesis and mechanical properties of carbon nanotube/diamond-like carbon composite films

Diamond-like carbon (DLC) coatings were successfully deposited on carbon nanotube (CNT) films with CNT densities of 1 × 10⁹/cm², 3 × 10⁹/cm², and 7 × 10⁹/cm² by a radio frequency plasma-enhanced chemical vapor deposition (CVD). The new composite films consisting of CNT/DLC were synthesized to improve the mechanical properties of DLC coatings especially for toughness. To compare those of the CNT/DLC composite films, the deposition of a DLC coating on a silicon oxide substrate was also carried out. A dynamic ultra micro hardness tester and a ball-on-disk type friction tester were used to investigate the mechanical properties of the CNT/DLC composite films. A scanning electron microscopic (SEM) image of the indentation region of the CNT/DLC composite film showed a triangle shape of the indenter, however, chippings of the DLC coating were observed in the indentation region. This result suggests the improvement of the toughness of the CNT/DLC composite films. The elastic modulus and dynamic hardness of the CNT/DLC composite films decreased linearly with the increase of their CNT density. Friction coefficients of all the CNT/DLC composite films were close to that of the DLC coating.     

Electrical and optical properties of diamond-like carbon films deposited by pulsed laser ablation

Pulsed laser ablation of a graphite target was carried out by ArF excimer laser deposition at a laser wavelength of 193 nm and fluences of 10 and 20 J/cm² to produce diamond-like carbon (DLC) films. DLC films were deposited on silicon and quartz substrates under 1 × 10^? 6 Torr pressure at different temperatures from room temperature to 250 °C. The effect of temperature on the electrical and optical properties of the DLC films was studied. Laser Raman Spectroscopy (LRS) showed that the DLC band showed a slight increase to higher frequency with increasing film deposition temperature. Spectroscopic ellipsometry (SE) and ultraviolet–visible absorption spectroscopy showed that the optical band gap of the DLC films was 0.8–2 eV and decreased with increasing substrate temperature. These results were consistent with the electrical resistivity results, which gave values for the films in the range 1.0 × 10⁴–2.8 × 10⁵ Ω cm and which also decreased with deposition temperature. We conclude that at higher substrate deposition temperatures, DLC films show increasing graphitic characteristics yielding lower electrical resistivity and a smaller optical band gap.     

Changes in chemical bonding of diamond-like carbon films by atomic-hydrogen exposure

We have deposited unhydrogenated diamond-like carbon (DLC) films on Si substrate by pulsed laser deposition using KrF excimer laser, and investigated the effects of atomic-hydrogen exposure on the structure and chemical bonding of the DLC films by photoelectron spectroscopy (PES) using synchrotron radiation and Raman spectroscopy. The fraction of sp³ bonds at the film surface, as evaluated from C1s spectra, increased at a substrate temperature of 400 °C by atomic-hydrogen exposure, whereas the sp³ fraction decreased at 700 °C with increasing exposure time. It was found that the sp³ fraction was higher at the surfaces than the subsurfaces of the films exposed to atomic hydrogen at both the temperatures. The Raman spectrum of the film exposed to atomic hydrogen at 400 °C showed that the clustering of sp² carbon atoms progressed inside the film near the surface even at such a low temperature as 400 °C.     

Structure of the silver containing diamond like carbon films: Study by multiwavelength Raman spectroscopy and XRD

In the present study structure of silver containing diamond like carbon (DLC:Ag) films deposited by reactive magnetron sputtering was investigated by X-ray diffractometry (XRD) and multiwavelength Raman spectroscopy. In the case of the DLC:Ag films containing low amount of silver, crystalline silver oxide prevails over silver. While at higher Ag atomic concentrations formation of the silver crystallites of the different orientations was observed. Surface enhanced Raman scattering (SERS) effect was detected for high Ag content in the films. For UV excited Raman spectra sp³ bonded carbon related Raman scattering T peak at ~ 1060 cm^− 1 was detected only for the films with the highest amount of silver (34.3 at.%). The dependence of the Raman scattering spectra parameters such as position of the G peak, G peak full width at half maximum (FWHM(G)), D/G peak area ratio on Ag atomic concentration in DLC:Ag film as well as Raman scattering spectra excitation wavelength were studied. The dependence on Ag amount in film was more pronounced in the case of the Raman scattering spectra excited by higher wavelength laser beam, while in the case of the spectra excited by 325 nm and 442 nm laser beams only weak dependence (or no dependence) was observed. Overall tendency of the decrease of the dispersion of the G peak with the increase of Ag atomic concentration was found. Thus sp³/sp² bond ratio in DLC:Ag film decreased with the increase of Ag atomic concentration in the films.     

Properties of DLC films deposited by an oxyacetylene flame

Diamond-like carbon (DLC) films were obtained by spinning a tungsten carbide substrate at a high speed using an oxyacetylene flame. The films deposited at a typical experimental condition of substrate temperature of 810°C, rotation of 600 rpm and 3 h deposition time, exhibited an uniform, very smooth, hard and glassy surface covering the entire exposed face of the substrate. These films were identified as DLC by their characteristic broad Raman spectra centered at 1554 cm⁻¹ and micro-Vicker's hardness >3400 kg mm⁻². For substrate temperatures <800°C the film started losing the uniform glassy surface and the hardness deteriorated. For temperatures >950°C the film was still hard and shiny, but black in color. DLC films were also obtained in a wide range of speeds of rotation (300–750 rpm), as long as the temperature remained close to 850°C.     

Nano-texture for a wear-resistant and near-frictionless diamond-like carbon

The effect of nano-scale surface texture on wear resistance of diamond-like carbon (DLC) films was studied using a reciprocating ball-on-flat tribometer in dry, humid, and liquid water environments. The nano-scale surface texture was produced by depositing ∼1 μm thick DLC films onto silicon substrates pre-textured with pyramidal wells and polystyrene spheres. The surface roughness of the textured DLC films was about 50 nm in both cases. The friction and wear behavior of the flat and nano-textured DLC films were tested with AISI 440C-grade stainless steel balls at a contact load creating about 360 nm deep Hertzian deformation which is significantly larger than the surface roughness. At this condition, nano-texturing did not affect the friction coefficient, but it significantly reduced the wear of DLC films in dry and humid nitrogen compared to flat DLC. In dry nitrogen, the nano-textured DLC films showed the ultra-low friction without substantial wear of DLC and deposition of thick transfer films onto the counter-surface. The wear reduction appeared to be related to the stress relief in the nano-textured DLC film. In liquid water, surface features on the nano-textured DLC films were diminished due to tribochemical oxidation and material removal at the sliding interface.     

The effect of refractive index on the friction coefficient of DLC coated polymer substrates

This paper describes the enhanced mechanical performance that can be achieved by the application of diamond-like carbon (DLC) coatings to polymer substrates. The polymers coated are silicone and polyethylene, and the effect on the friction coefficient is studied. Film adhesion is found to depend on the DLC film refractive index (n), whereas the friction is largely independent of n in the range studied. Films were deposited from a He/C₂H₂ mixture at 20 Pa (0.15 Torr) on to the polymer substrates placed on a 10-cm-diameter electrode driven at 13.56 MHz. Film growth was monitored by in-situ ellipsometry (at 675 nm), which was performed on a glass slide placed near the polymer substrate. Friction measurements were obtained using a pin-on-disk tribometer, and measurements were carried out using a stainless-steel pin at a linear speed of 6 cm s⁻¹. Film adhesion was evaluated using a pull-adhesion tester. It was found that DLC coatings adhere well to the polymer substrates and can significantly reduce the friction coefficient of polymers such as silicone. Higher refractive index films (which are harder and have a higher mechanical strength) were found to have a poorer adhesion and provide a slightly increased friction on the polymer surface when compared to lower-index films. This study indicates that DLC may be used to enhance the tribological properties of polymers with potential applications in the biomaterials and light-engineering industries.     

A study of hard diamond-like carbon films in mid-frequency dual-magnetron sputtering

A series of hydrogen-free diamond-like carbon (DLC) films were deposited by a mid-frequency dual-magnetron sputtering under basic conditions of Cr and C target power density between 6 and 18 W/cm², bias voltage in a range of − 100 V to − 200 V, and a pure argon atmosphere. Microstructure, microhardness, adhesion, friction and wear properties were investigated for the DLC films to be used as protective films on cutting tools and forming dies, etc. The DLC films exhibited some combined superior properties: high hardness of 30–46 GPa, good adhesion of critical load of 50–65 N, and friction coefficient about 0.1 in air condition. Properties of the magnetron-sputtered carbon films showed a strong dependence on flux and energy of ion bombardment during growth of the films.     

Large-area uniform hydrogen-free diamond-like carbon films prepared by unbalanced magnetron sputtering for infrared anti-reflection coatings

The hydrogen-free diamond-like carbon (DLC) films are potential materials to be used as infrared anti-reflection protective coatings if their optical absorption can be reduced to get relatively thick films needed. In this study, hydrogen-free DLC films were deposited by the physical vapor deposition (PVD) method in an unbalanced magnetron sputtering (UBMS) system with a rectangle graphite target of 440 × 80 mm in the argon atmosphere. The UBMS system was described in detail and the magnetron field distribution of the target was denoted in this work. The film thickness uniformity was investigated and the results showed that this system is capable of depositing uniform films larger than 150 mm in diameter. The infrared transmission spectra of DLC films were analyzed by a FTIR spectrometer, the results indicating that transparent films were obtained in the infrared region for the single side DLC coated on the silicon and germanium substrates, and about 68.83% and 63.05% transmittance were achieved respectively at the wave number of 2983 /cm, close to theoretical value for non-absorption carbon material. No obvious absorption peaks were found between 5000 and 800 /cm. The refractive index and extinction coefficient of the DLC films deposited under optimized conditions were about 2.08 and 0.067 respectively at the wavelength of 1600 nm. These important optical characteristics showed that the hydrogen-free DLC films prepared in the UBMS system were suitable for infrared transmission enhancement applications.     

Microstructure and tribological properties of ternary BCN thin films with different carbon contents

Boron carbon nitrogen (BCN) thin films with different carbon contents are deposited on high-speed steel substrates by reactive magnetron sputtering (RMS) and their microstructure and tribological properties are studied. The BCN films with carbon contents from 26.9 wt.% to 61.3 wt.% have an amorphous structure with variable amounts of carbon bonds (sp²C–C, sp²C–N and sp³C–N bonds). A higher carbon content enhances the film hardness but reduces the friction coefficient against GCr15 steel balls in air. BCN films with higher hardness, lower friction coefficient, and better wear resistance can be obtained by increasing the carbon content.     

Effect of oxygen plasma treatment on non-thrombogenicity of diamond-like carbon films

The non-thrombogenicity of oxygen-plasma-treated DLC films was investigated as surface coatings for medical devices. DLC films were deposited on polycarbonate substrates by a radio frequency plasma enhanced chemical vapor deposition method using acetylene gas. The deposited DLC films were then treated with plasma of oxygen gas at powers of 15 W, 50 W, and 200 W. Wettability was evaluated by water contact angle measurements and the changes in surface chemistry and roughness were examined by X-ray photoelectron spectroscopy and atomic force microscope analysis, respectively. Each oxygen-plasma-treated DLC film exhibited a hydrophilic nature with water contact angles of 11.1°, 17.7° and 36.8°. The non-thrombogenicity of the samples was evaluated through the incubation with platelet-rich plasma isolated from human whole blood. Non-thrombogenic properties dramatically improved for both 15 W- and 50 W-oxygen-plasma-treated DLC films. These results demonstrate that the oxygen plasma treatment at lower powers promotes the non-thrombogenicity of DLC films with highly hydrophilic surfaces.     

Influence of bias voltage on diamond like carbon (DLC) film deposited on polyethylene terephthalate (PET) film surfaces using PECVD and its blood compatibility

In this paper, diamond like carbon (DLC) films were coated on polyethylene terephthalate (PET) film substrate as a function of biasing voltage using plasma enhanced chemical vapour deposition. The surface morphology of the DLC films was analyzed by scanning electron microscopy and atomic force microscopy. The chemical state and structure of the films were analyzed by X-ray photoelectrons spectroscopy and Raman spectroscopy. The micro hardness of the DLC films was also studied. The surface energy of interfacial tension between the DLC and blood protein was investigated using contact angle measurements. In addition, the blood compatibility of the films was examined by in vitro tests. For a higher fraction of sp³ content, maximum hardness and surface smoothness of the DLC films were obtained at an optimized biasing potential of ? 300 V. The in vitro results showed that the blood compatibility of the DLC coated PET film surfaces got enhanced significantly.     

Structure and characteristics of amorphous (Ti,Si)–C:H films deposited by reactive magnetron sputtering

The hydrogenated amorphous carbon films doped with Ti and Si ((Ti,Si)–C:H) were deposited on silicon substrates using reactive magnetron sputtering Ti₈₀Si₂₀ composite target in an argon and methane gas mixture. The structures of the films were analyzed by X-ray photoelectron spectroscopy and Visible Raman spectroscopy. The morphologies were observed by atomic force microscope. The friction coefficients of the films were tested on the ball-on-disc tribometer. The results indicate that the sp³/sp² ratios in the films can be varied from 0.18 to 0.63 by changing Ti and Si contents at various CH₄ flow rates. The surface of the films becomes smoother and more compact as the CH₄ flow rate increases. The lowest friction coefficient is as low as 0.0139 for the film with Ti of 4.5 at.% and Si of 1.0 at.%. Especially, the film exhibits a superlow value (μ < 0.01) under ambient air with 40% relative humidity in friction process. The superlow friction coefficient in ambient air may be, attributable to synergistic effects of a combination of Ti and Si in the film.     

Structural and mechanical properties of DLC films prepared by bipolar PBII&D

In the present study, diamond-like carbon (DLC) films were prepared by bipolar plasma based ion implantation and deposition (PBII&D), and the structural and mechanical properties of the DLC films deposited on Si substrates were evaluated by Raman spectroscopy. In the PBII&D processing, the positive and negative pulse voltages were varied from 1 to 3 kV and from ? 1 to ? 15 kV, respectively. With an increase in the pulse voltages, the Raman G-peak position and I(D) / I(G) ratio increased, and the G-peak full width at half maximum (FWHM(G)) decreased, indicating graphitization of the DLC films. In the low wavenumber regime, the FWHM(G) increases when the G-peak shifts to higher wavenumbers, reaching a maximum value at around 1540 cm^? 1, and then decreases. This behavior was due to the structural changes occurring in the DLC films with an increase in the wavenumber. DLC to polymer-like carbon (PLC) transition occurred in the low wavenumber regime, and DLC to graphite-like carbon (GLC) transition occurred in the high wavenumber regime. Further, two different trends were observed in the relationship between the mechanical properties (hardness, elastic modulus, and internal stress) of the DLC films and the FWHM(G), originating from the structural change from DLC to GLC and PLC.     

Wear-corrosion behavior of ultra-thin diamond-like carbon nitride films on aluminum alloy

Diamond-like carbon films exhibit high hardness, high wear resistance and a low friction coefficient. They are extensively utilized in the mechanical, electronic and biomedical industries. This work evaluates the effect of the thickness of ultra-thin diamond-like carbon nitride films on their corrosion properties and their wear-corrosion resistance in a mixed 1 M NaCl + 1 M H₂SO₄ solution using electrochemical methods. The corrosion current density and weight loss of all films during and after wear-corrosion test are also recorded. This work employs ion beam-assisted deposition (IBAD) to deposit DLC nitride films of various thicknesses (1.5, 2.0, 2.5 and 3.0 nm), containing 60% nitrogen gas in the form of a gaseous mixture of C₂H₂ + 60%N₂. The thickness of the films was measured using a transmission electron microscope (TEM). The atomic bonding structures of these DLC nitride films are analyzed using a Raman spectrometer and by electron spectroscopy for chemical analysis (ESCA). A scanning electron microscope (SEM) was adopted to elucidate the surface morphologies of the specimens after corrosion and wear-corrosion. The results indicated that all of the nitrogen-containing DLC films excellently protected the 5088 Al–Mg alloy substrate with an electroless plated Ni–P interlayer against corrosion, and that the degree of protection increases with the thickness of the film. In the wear-corrosion tests various potentials were applied during wear in the particular corrosive solution. The results further demonstrated that the wear-corrosion resistance of all the nitrogen-containing DLC films was as effective as corrosion protection, and that the wear-corrosion loss decreased as the film thickness increased.     

Tribological properties of polymer composites with diamond-like carbon flakes

Composites of epoxy resin with diamond-like carbon (DLC) flakes were fabricated. The DLC flakes were prepared from a DLC film deposited by chemical vapor deposition on an aluminum substrate. The tribological properties of composites were evaluated in air and water environments using a reciprocating friction tester and an AISI 440C mating ball. The friction coefficient of the epoxy composite decreased from 0.90 to 0.69 in air and from 0.71 to 0.29 in water with the addition of DLC flakes. The specific wear rate of the composite also decreased from 5 × 10^? 5 to 7 × 10^? 6 mm³/N m in air and from 4 × 10^? 5 to 4 × 10^? 6 mm³/N m in water. In contrast, the wear of the mating ball increased. Furthermore, the tribological properties of DLC flakes as an additive in water were evaluated. The suspension of powdered DLC in water reduced the friction coefficient of epoxy resin against the AISI 440C mating ball. Furthermore, the wear of the resin was negligibly small, although severe abrasive wear on the mating ball was observed.     

Localized DLC etching by a non-thermal atmospheric-pressure helium plasma jet in ambient air

Using a versatile atmospheric-pressure helium plasma jet, diamond-like carbon (DLC) films were etched in ambient air. We observed that the DLC films are etched at a nominal rate of around 60 nm/min in the treated area (230 μm in diameter) during a 20-min exposure. The etching rate increased after the initial 10-min exposure. During this period, the flat DLC surface was structurally modified to produce carbon nanostructures with a density of ~ 2.4 × 10¹¹ cm^− 2. With this increase in surface area, the etching rate increased. After 20 min, the DLC film had a circular pattern etched into it down to the substrate where silicon nanostructures were observed with sizes varying from 10 nm to 1 μm. The initial carbon nanostructure formation is believed to involve selective removal of the sp²-bonded carbon domains. The carbon etching results from the formation of reactive oxygen species in the plasma.     

Electron field emission from filtered arc deposited diamond-like carbon films using Au and Ti layers

In this work, tetrahedral diamond-like carbon (DLC) films are deposited on Si, Ti/Si and Au/Si substrates by a new plasma deposition technique — filtered arc deposition (FAD). Their electron field emission characteristics and fluorescent displays of the films are tested using a diode structure. It is shown that the substrate can markedly influence the emission behavior of DLC films. An emission current of 0.1 μA is detected at electric field E_DLC/Si=5.6 V/μm, E_DLC/Au/Si=14.3 V/μm, and E_DLC/Ti/Si=5.2 V/μm, respectively. At 14.3 V/μm, an emission current density J_DLC/Si=15.2 μA/cm², J_DLC/Au/Si=0.4 μA/cm², and J_DLC/Ti/Si=175 μA/cm² is achieved, respectively. It is believed that a thin TiC transition layer exists in the interface between the DLC film and Ti/Si substrate.