Electronic conductivity,oxygen permeability and thermal expansion of Sr0.7Ce0.3Mn1−xAlxO3−δ

The maximum solubility of aluminum cations in the perovskite lattice of Sr_0.7Ce_0.3Mn_1−xAl_xO_3−δ is approximately 15%. The incorporation of Al³⁺ increases oxygen ionic transport due to increasing oxygen nonstoichiometry, and decreases the tetragonal unit cell volume and thermal expansion at temperatures above 600 °C. The total conductivity of Sr_0.7Ce_0.3Mn_1−xAl_xO_3−δ (x = 0–0.2), predominantly electronic, decreases with aluminum additions and has an activation energy of 10.2–10.9 kJ/mol at 350–850 °C. Analysis of the electronic conduction and Seebeck coefficient of Sr_0.7Ce_0.3Mn_0.9Al_0.1O_3−δ, measured in the oxygen partial pressure range from 10⁻¹⁸ to 0.5 atm at 700–950 °C, revealed trends characteristic of broad-band semiconductors, such as temperature-independent mobility. The temperature dependence of the charge carrier concentration is weak, but exhibits a tendency to thermal excitation, whilst oxygen losses from the lattice have an opposite effect. The role of the latter factor becomes significant at temperatures above 800 °C and on reducing p(O₂) below 10⁻⁴ to 10⁻² atm. The oxygen permeability of dense Sr_0.7Ce_0.3Mn_1−xAl_xO_3−δ (x = 0–0.2) membranes, limited by both bulk ionic conduction and surface exchange, is substantially higher than that of (La, Sr)MnO₃-based materials used for solid oxide fuel cell cathodes. The average thermal expansion coefficients of Sr_0.7Ce_0.3Mn_1−xAl_xO_3−δ ceramics in air are (10.8–11.8) × 10⁻⁶ K⁻¹.     

Magnetic properties of Er(Co,Mn)O3 perovskites

The erbium-based manganite ErMnO₃ has been partially substituted at the manganese site by Co in the general formula ErCo_xMn_1−xO₃. The perovskite orthorhombic structure is found from x(Co) = 0.3 up to x(Co) = 0.7, provided that the synthesis is performed under oxygenation conditions to favour the presence of Co³⁺. Magnetic properties show unusual phenomena, correlated with the presence of different magnetic entities (i.e., Er³⁺, Co²⁺, Co³⁺, Mn³⁺, Mn⁴⁺): the overall magnetic moment reverses its sign when the sample is cooled under an external magnetic field, while the magnetization loops performed at T < 4 K show intersecting branches at low fields and a sudden jump at high fields. A phenomenological model of two interacting sublattices, coupled by an antiferromagnetic exchange interaction, explains the inversion of the overall spin, while the high-field discontinuity is explained in terms of dynamical models.     

Nanocrystalline/nanosized manganese substituted nickel ferrites – Ni1−xMnxFe2O4 obtained by ceramic-mechanical milling route

Manganese substituted nickel ferrites, Ni_1−xMn_xFe₂O₄ (x=0, 0.3, 0.5 and 0.7) have been obtained by a combined method, heat treatment and subsequent mechanical milling. The samples were characterised by X-ray diffraction, differential scanning calorimetry and magnetic measurements. The increase of the Mn²⁺ cations amount into the spinel structure leads to a significant expansion of the cubic spinel structure lattice parameter. The crystallite size decreases with increasing milling time up to 120 min, more rapidly for the nickel–manganese ferrites with a large amount of Mn²⁺ cations (x=0.7). After only 15 min of milling the mean crystallites size is less than 25 nm for all synthesised ferrites. The Néel temperature decreases by increasing Mn²⁺ cation amount from 585 °C for x=0 up to 380 °C for x=0.7. The magnetisation of the ferrite increases by introducing more manganese cations into the spinel structure. The magnetisation of the milled samples decreases by increasing milling time for each ratio among Ni and Mn cations and tends to be difficult to saturate, a behaviour assigned to the spin canted effect.     

Influence of Ce addition on the structural,magnetic, and magnetocaloric properties in La0.7−xCexSr0.3MnO3 (0≤x≤0.3) ceramic compound

We report improvement in the magnetocaloric properties of Ce-doped lanthanum manganites. Polycrystalline La_0.7−xCe_xSr_0.30MnO₃ (0≤x≥0.3) samples were prepared using the conventional solid-state reaction method with phase purity and structure confirmed using X-ray diffraction. Temperature dependent magnetization measurements and Arrott analysis reveal second order ferromagnetic transition in parent sample and as well as in doped sample with Curie temperature decreasing progressively with increasing Ce-concentration from ~370 K for x=0.0 to 310 K for x=0.30. Magnetic entropy change (ΔS_M) was calculated by applying the thermodynamic Maxwell equation to a series of isothermal field dependent magnetization curves. A large ΔS_M associated with the ferromagnetic–paramagnetic transition in La_0.7−xCe_xSr_0.30MnO₃ samples has been observed. The value of ΔS_M was found to increase with Ce-doping up to x=0.15 and the highest value of 2.12 J kg⁻¹ K⁻¹ (at ΔH=2 T) was observed for La_0.55Ce_0.15Sr_0.30MnO₃ sample near the Curie temperature of 356 K. Also, improved relative cooling power of ~122 J kg⁻¹ was observed for the same sample. Due to the large magnetic entropy change and high Curie temperature, the La_0.55Ce_0.15Sr_0.30MnO₃ sample is suggested to be used as potential magnetic refrigerants for magnetic refrigeration technology above room temperature.     

Catalytic activity of nanometer La1−xSrxCoO3 (x = 0, 0.2) perovskites towards VOCs combustion

Combustive oxidation of volatile organic compounds (VOCs), such as propyl alcohol, toluene and cyclohexane, were studied. The combustion was catalyzed by nanoparticles of La_1−xSr_xCoO₃ (x = 0, 0.2) perovskites prepared by a co-precipitation method. The results showed high activities of the perovskite catalysts. Compared to LaCoO₃, in particular, La_0.8Sr_0.2CoO₃ was much higher in catalytic ability. The total oxidation of VOCs followed the increasing order: cyclohexane < toluene < propyl alcohol. The T_99% of cyclohexane was 40 °C lower than that of toluene, which appeared to be determined by the bond strengths of the weakest C–H and C–C bonds. The 100-h stability experiments showed that La_1−xSr_xCoO₃ (x = 0, 0.2) perovskite was highly stable.     

Preferential occupancy of metal ions in the hydroxyapatite solid solutions synthesized by hydrothermal method

The solid solutions in the systems of Ca-Cd HAp [Ca_10−xCd_xHAp (x = 0–10)], Ca-Sr HAp [Ca_10−xSr_xHAp (x = 0–10)] and Ca-Pb HAp [Ca_10−xPb_xHAp (x = 0–10)], were successfully synthesized at 200 °C for 12 h under hydrothermal conditions. The site of the metal ions in the solid solutions was analyzed by the Rietveld method. The results of the Rietveld analysis indicated that the metal ions of Pb²⁺, Sr²⁺, and Cd²⁺ all preferentially occupied M (2) sites in the apatite structure. The preferential occupancy of the metal ions in M (2) sites were explained mainly by their ionic radius and electronegativity.     

Magnetic properties of Cu1+xMn2−xO4 and Ni1+xMn2−xO4 solid solutions

Magnetic properties of two spinel oxides solid solutions, Cu_1+xMn_2−xO₄ and Ni_1+xMn_2−xO₄, are reported. These series are characterized by two magnetic transitions: the upper one, of ferrimagnetic type, occurs at about 85 K (for copper-based) and at 105–110 K (for nickel-based spinels), independently of the x-content; the lower transition may be related to a Néel-type collinear ordering and takes place at 30 and 45 K, respectively. Application of moderate fields (H > 250 Oe) make both transitions to merge into one broad maximum in the magnetization, which takes place at lower temperature when applying larger fields. Magnetization cycles with temperature (ZFC/FC) or field (loops) allowed us to well characterize the ordered state. The effective moment follows the expected behavior when manganese ions are being substituted by ions of lower magnetic moment (Ni²⁺ and Cu²⁺).     

Phase relationships and transport in Ti-, Ce- and Zr-substituted lanthanum silicate systems

The solubility of Ti⁴⁺ in the lattice of apatite-type La_9.83Si_6−xTi_xO_26.75 corresponds to approximately 28% of the Si-site density. The conductivity of La_9.83Si_6−xTi_xO_26.75 (x = 1–2) is predominantly oxygen-ionic and independent of the oxygen partial pressure in the p(O₂) range from 10⁻²⁰ to 0.3 atm. The electron transference numbers determined by the modified faradaic efficiency technique are lower than 0.006 at 900–950 °C in air. The open-circuit voltage of oxygen concentration cells with Ti-doped silicate electrolytes is close to the theoretical Nernst value both under oxygen/air and air/10%H₂–90%N₂ gradients at 700–950 °C, suggesting the stabilization of Ti⁴⁺ in the apatite structure. Titanium addition in La_9.83Si_6−xTi_xO_26.75 (x = 1–2) leads to decreasing ionic conductivity and increasing activation energies from 93 to 137 kJ/mol, and enhanced degradation in reducing atmospheres due to SiO volatilization. At p(O₂) = 10⁻²⁰ atm and 1223 K, the conductivity decrease after 100 h was about 5% for x = 1 and 17% for x = 2. The solubility of Zr⁴⁺ in the La_9.83Si_6−xZr_xO_26.75 system was found to be negligible, while the maximum concentration of Ce⁴⁺ in La_9.4−xCe_xSi₆O_27−δ is approximately 5% with respect to the number of lanthanum sites.     

Influence of Al-substitution on structures,resistivity and magnetic properties of LaxSr(2−x)Fe(1+y)Mo(1−y)O6 (x=3y,y=0.05, 0.1, 0.15, 0.2)

Two series of single-phased La_xSr_(2−x)Fe_(1+y)Mo_(1−y)O₆ and La_xSr_(2−x)Fe_(1+0.5y)Al_0.5yMo_(1−y)O₆ (x=3y, y=0.05, 0.1, 0.15 and 0.2) double perovskites were prepared by solid-state reaction. The effects of Al-substitution on the structures, resistivity and magnetic properties of La_xSr_(2−x)Fe_(1+y)Mo_(1−y)O₆ were investigated. Although Al-replacement exhibits a negligible influence of on the B-site ordering degree, it results in the suppression of magnetisation caused by non-magnetic Al³⁺ ions. Reduction of grain sizes leads to increased resistivity, thus an optimised magnetoresistance (MR) behaviour is observed. The greatest MR extent improvement can be obtained when y is 0.15 and the MR% of the Al-doped ceramics reaches −10.5% (10 K, 1 T), which is 2 times greater than that of the undoped ceramics (−4.6%, 10 K, 1 T). Interestingly, the Curie temperature (Tc) of both Al-doped and undoped samples maintained relatively constant values of approximately 420 K and 405 K, respectively, which were different results from the data obtained for similar electron-doping systems in the literature.     

Ionic conductivity of Mn2+ doped dense tin pyrophosphate electrolytes synthesized by a new co-precipitation method

Mn²⁺-doped Sn_1−xMn_xP₂O₇ (x = 0–0.2) are synthesized by a new co-precipitation method using tin(II)oxalate as tin(IV) precursor, which gives pure tin pyrophosphate at 300 °C, as all the reaction by-products are vaporizable at <150 °C. The dopant Mn²⁺ acts as a sintering aid and leads to dense Sn_1−xMn_xP₂O₇ samples on sintering at 1100 °C. Though conductivity of Sn_1−xMn_xP₂O₇ samples in the ambient atmosphere is 10⁻⁹–10⁻⁶ S cm⁻¹ in 300–550 °C range, it increases significantly in humidified (water vapor pressure, pH₂O = 0.12 atm) atmosphere and reaches >10⁻³ S cm⁻¹ in 100–200 °C range. The maximum conductivity is shown by Sn_0.88Mn_0.12P₂O₇ with 9.79 × 10⁻⁶ S cm⁻¹ at 550 °C in ambient air and 2.29 × 10⁻³ S cm⁻¹ at 190 °C in humidified air. It is observed that the humidification of Sn_1−xMn_xP₂O₇ samples is a slow process and its rate increases at higher temperature. The stability of Sn_1−xMn_xP₂O₇ samples is analyzed.     

Dynamical behavior of step-like transition of La0.5Sr0.5Mn1−xTixO3 in a widened field sweep rate

The magnetization behavior of Ti⁴⁺ doped perovskite manganites La_0.5Sr_0.5Mn_1−xTi_xO₃ (x=0.15, 0.175 and 0.2) was investigated. Experimental results show that Ti⁴⁺ dopant suppresses the antiferromagnetic charge ordering and leads to a step-like magnetization behavior below 3 K. The step-like transitions and the critical magnetic fields are strongly dependent on the Ti doping level, magnetic field sweep rate and temperature. Above 3 K, the step-like transitions transform to broad ones. In addition, under pulsed high magnetic fields with an ultrafast field sweep rate of ~10³ T/s, the sharp step-like transitions observed in the static magnetization measurements become smooth metamagnetic transition at low temperatures. This feature is correlated with the collapse of the balance between the magnetic energy and elastic energy in the phase separation system within a martensitic-like scenario.     

Role of oxygen pressure on the stability of lanthanum strontium manganite–yttria stabilized zirconia composite

We have investigated the structural and chemical stability of La_0.8Sr_0.2MnO₃ (LSM)–8 mol.% yttria stabilized zirconia (YSZ) composite. LSM and YSZ powders were mixed and sintered at 1400 °C for 10 h in controlled atmosphere (PO₂ = 0.21 to 10^?6 atm). The unit cell volume of LSM increases during exposure to reduced oxygen partial pressure while it remains unchanged for YSZ. During reduction in the oxygen partial pressure from 0.21 atm to 10^?6 atm, the solubility of manganese in YSZ increases from ～10 at.% to ～15 at.%. Lower oxygen partial pressure also results in the grain growth and formation of La₂Zr₂O₇ and MnO_x (Mn₃O₄) compounds lowering the stability of the LSM–YSZ composite. On subsequent sintering in 0.21 atm PO₂, the La₂Zr₂O₇ and MnO_x compounds tend to disappear indicating the reversibility of the interaction. The reversibility of LSM–YSZ reaction has been independently confirmed using La₂Zr₂O₇ and MnO_x.     

Effect of La doping on tunable behavior of sol–gel-derived PST thin film

Pb_xSr_1−xTiO₃ and (Pb_0.4Sr_0.6)_1−xLa_2x/3TiO₃ thin films were prepared on ITO/glass substrate by sol–gel technique. The crystalline phase structures of thin films were investigated by XRD. The dielectric properties were measured by LCZ meter. Results show that the perovskite phase was stable in Pb_xSr_1−xTiO₃ thin film. Its lattice constant was found to increase with the increase of x. When Pb/Sr ratio was about 50/50, the transformation of the perovskite phase between cubic and tetragonal took place at room temperature. To ensure better tunability, Pb_0.4Sr_0.6TiO₃ thin film was selected in both paraelectric state (cubic structure) and near the phase transformation point between cubic and tetragonal. The tunability of more than 80% and figure of merit (FOM) of 14.17 were obtained. (Pb_0.4Sr_0.6)_1−xLa_2x/3TiO₃ was also prepared as La-doped thin film. Its dielectric constant was decreased below x = 0.4 and then increased above x = 0.4 with the increase in x. The inharmonic coefficient depicting ability of tunability of (Pb_0.4Sr_0.6)_1−xLa_2x/3TiO₃ thin film kept constant due to the changeable shape of the crystal cell under electric field at a fixed temperature below x = 0.4, which is in good agreement with Johnson's theory. And the coefficient reveals a distinctive variable because of easily changeable shape under different bias above x = 0.4. The tunability of about 70% and FOM of about 7 were obtained in the (Pb_0.4Sr_0.6)_1−xLa_2x/3TiO₃ thin film.     

Synthesis,structure and oxygen thermally programmed desorption spectra of La1−xCaxAlyFe1−yO3−δ perovskites

Perovskites La_1−xCa_xAl_yFe_1−yO_3−δ (x, y = 0 to 1) were prepared by high-temperature solid-state synthesis based on mixtures of oxides produced by colloidal milling. The XRD analysis showed that perovskites La_0.5Ca_0.5Al_yFe_1−yO_3−δ with a high Fe content (1 − y = 0.8–1.0) were of orthorhombic structure, perovskites with a medium Fe content (1 − y = 0.8–0.5) were of rhombohedral structure, and perovskite with the lowest Fe content (1 − y = 0.2) were of cubic structure. Thermally programmed desorption (TPD) of oxygen revealed that chemical desorption of oxygen in the temperature range from 200 to 1000 °C had proceeded in the two desorption peaks. The low-temperature α-peak (in the 200–550 °C temperature range) was brought about by oxygen liberated from oxygen vacancies; the high-temperature β-peak (in the 550–1000 °C temperature range) corresponded to the reduction of Fe⁴⁺ to Fe³⁺. The chemidesorption oxygen capacity increased with increasing Ca content and decreased with increasing Al content in the perovskites. The Al³⁺ ions restricted, probably for kinetic reasons, the reduction of Fe⁴⁺ and the high-temperature oxygen desorption associated with it.     

Structural and electrical characterization of Sr- and Al- doped apatite type lanthanum silicates prepared by the pechini method

The subject of this work regards the synthesis of La_9.83−xSr_xSi_6−yAl_yO_26+δ (0≤x,y≤0.5) via a modified Pechini method. The compounds where characterized by XRD and SEM. Pure La_9.83Si₆O_26+δ, La_9.38Sr_0.45Si₆O_26+δ and La_9.38Sr_0.45Si_5.70Al_0.30O_26+δ were prepared after sintering at 1400 °C for 20 h while La_9.38Sr_0.45Si_5.55Al_0.45O_26+δ and La_9.38Sr_0.45Si_5.50Al_0.50O_26+δ contained traces (<8%) of La₂SiO₅ as secondary phase. Rietveld analysis showed that La_9.83−xSr_xSi_6−yAl_yO_26+δ (0≤x,y≤0.5) compounds crystallize in the P6₃/m space group. Al doping on Si site exhibits more pronounced effect upon structural parameters in comparison to Sr doping on La site. Interstitial oxygen accommodates a position at the periphery of the hexagonal channels in the vicinity of the SiO₄ groups. Ion conduction is close related with the size of the hexagonal channels and the interstitial oxygen content. The ion conductivity is promoted when an optimum balance between the aforementioned magnitudes is reached. The LS and LsSa4530 compounds exhibit the highest values of ionic conductivity at 700 °C with 11 and 14 mS/cm and activation energy of 0.47 and 0.46 eV, respectively.     

Oxygen ionic transport in SrFe1−yAlyO3−δ and Sr1−xCaxFe0.5Al0.5O3−δ ceramics

The oxygen permeability of mixed-conducting Sr_1−xCa_xFe_1−yAl_yO_3−δ (x=0–1.0; y=0.3–0.5) ceramics at 850–1000 °C, with an apparent activation energy of 120–206 kJ/mol, is mainly limited by the bulk ionic conduction. When the membrane thickness is 1.0 mm, the oxygen permeation fluxes under pO₂ gradient of 0.21/0.021 atm vary from 3.7×10⁻¹⁰ mol s⁻¹ cm⁻² to 1.5×10⁻⁷ mol s⁻¹ cm⁻² at 950 °C. The maximum solubility of Al³⁺ cations in the perovskite lattice of SrFe_1−yAl_yO_3−δ is approximately 40%, whilst the brownmillerite-type solid solution formation range in Sr_1−xCa_xFe_0.5Al_0.5O_3−δ system corresponds to x>0.75. The oxygen ionic conductivity of SrFeO₃-based perovskites decreases moderately on Al doping, but is 100–300 times higher than that of brownmillerites derived from CaFe_0.5Al_0.5O_2.5+δ. Temperature-activated character and relatively low values of hole mobility in SrFe_0.7Al_0.3O_3−δ, estimated from the total conductivity and Seebeck coefficient data, suggest a small-polaron mechanism of p-type electronic conduction under oxidising conditions. Reducing oxygen partial pressure results in increasing ionic conductivity and in the transition from dominant p- to n-type electronic transport, followed by decomposition. The low-pO₂ stability limits of Sr_1−xCa_xFe_1−yAl_yO_3−δ seem essentially independent of composition, varying between that of LaFeO_3−δ and the Fe/Fe_1−γO boundary. Thermal expansion coefficients of Sr_1−xCa_xFe_1−yAl_yO_3−δ ceramics in air are 9×10⁻⁶ K⁻¹ to 16×10⁻⁶ K⁻¹ at 100–650 °C and 12×10⁻⁶ K⁻¹ to 24×10⁻⁶ K⁻¹ at 650–950 °C. Doping of SrFe_1−yAl_yO_3−δ with aluminum decreases thermal expansion due to decreasing oxygen nonstoichiometry variations.     

Crystal structure,thermal expansion and electrical conductivity of perovskite oxides BaxSr1−xCo0.8Fe0.2O3−δ (0.3 ≤ x ≤ 0.7)

Ba_xSr_1−xCo_0.8Fe_0.2O_3−δ (0.3 ≤ x ≤ 0.7) composite oxides were prepared and characterized. The crystal structure, thermal expansion and electrical conductivity were studied by X-ray diffraction, dilatometer and four-point DC, respectively. For x ≤ 0.6 compositions, cubic perovskite structure was obtained and the lattice constant increased with increasing Ba content. Large amount of lattice oxygen was lost below 550 °C, which had significant effects on thermal and electrical properties. All the dilatometric curves had an inflection at about 350–500 °C, and thermal expansion coefficients were very high between 50 and 1000 °C with the value larger than 20 × 10⁻⁶ °C⁻¹. The conductivity were larger than 30 S cm⁻¹ above 500 °C except for x > 0.5 compositions. Furthermore, conductivity relaxation behaviors were also investigated at temperature 400–550 °C. Generally, Ba_0.4Sr_0.6Co_0.8Fe_0‘2O_3−δ and Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ are potential cathode materials.     

Effect of Ce and Yb co-doping on conductivity of LaNbO4

La_1−x−yCe_xYb_yNbO₄ specimens with various Ce and Yb contents were prepared by solid reactions, and their crystal structure, element valence, sinterability and conductivity were investigated. LaNbO₄-type single phase was formed at 1200 °C in air, and the lattice of La_1−x−yCe_xYb_yNbO₄ was distorted from that of LaNbO₄ to various extents, depending on the added amount of Ce and Yb. Both La and Nb remained the same valence as they are in LaNbO₄; Ce⁴⁺, Ce³⁺ and Yb³⁺ were detected at room temperature. Highly densified La_1−x−yCe_xYb_yNbO₄ specimens were achieved by sintering at above 1215 °C in air with conductivity 1–2 orders higher than that of pure LaNbO₄ in dry air, wet air and wet 5% H₂–N₂ atmospheres. The conductivity changed with testing atmosphere owing to the competition of electron and proton conduction, and maximal value 4.7 × 10⁻⁴ S cm⁻¹ was obtained in wet air at 900 °C.     

Microwave dielectric properties of tungstenbronze type like (Ba1−αSrα)6−3xR8+2xTi18O54 (R = Sm,Nd) solid solutions

Tungstenbronze type like Ba_6−3xR_8+2xTi₁₈O₅₄ (R = Sm or Nd) dielectric ceramics reveal high quality factor Q·f as well as high dielectric constant ɛ_r. We have investigated the effect of Sr substitution for Ba ions on the microwave dielectric properties of the compounds. (Ba_1−αSr_α)_6−3xR_8+2xTi₁₈O₅₄ (R = Sm or Nd) ceramics were prepared in the composition ranges of x = 0–0.2 and α = 0–0.312 and the microwave dielectric properties were investigated. (Ba_1−αSr_α)_6−3xSm_8+2xTi₁₈O₅₄, where x = 0.1 and α = 0.298, and (Ba_1−αSr_α)_6−3xNd_8+2xTi₁₈O₅₄, where x = 0.2, α = 0.296 revealed remarkably higher Q·f value among the solid solutions, indicating that Q·f increased with substituting Sr ions into Ba ions at the rhombic A1-site. This fact suggests that relaxation of local distortions at the A1-sites is closely related to improvement of Q·f.     

Ordering structure of barium magnesium niobate ceramic with A-site substitution

The ordering behaviour of Ba(Mg_1/3Nb_2/3)O₃ ceramics (BMN) substituted by La³⁺, Na⁺, K⁺ was investigated using X-ray powder diffraction and transmission electron microscopy. The 1:2 ordered structure of BMN can be transformed to 1:1 ordered structure by substituting a small amount of La cation ion into the A-site. Moreover, the degree of ordering was increased with La content in the compound, and reached almost unity at [La] = 50 mol%. When the La ion in (Ba_1−xLa_x)(Mg_(1+x)/3Nb_(2−x)/3)O₃ (BLMN) was substituted by Na or K ions, the 1:1 ordered structure of BLMN was transformed into the 1:2 ordered structure. The degree of 1:2 ordering was influenced by the sintering temperature and the size difference between the A and B site ions.