Modelling of an indirect internal reforming solid oxide fuel cell

Creation of an autothermal system by coupling an endothermic to an exothermic reaction demands the matching of the thermal requirements of the two reactions. The application under study is a solid oxide fuel cell (SOFC) with indirect internal reforming (IIR) of methane, whereby the endothermic steam reforming reaction is thermally coupled to the exothermic oxidation reactions. A steady-state model of an IIR-SOFC has been developed to study the mismatch between the thermal load associated with the rate of steam reforming at typical SOFC temperatures and the local amount of heat available from the fuel cell reactions. Results have shown a local cooling effect, undesirable for ceramic fuel cells, close to the reformer entrance. The system behaviour towards changes in catalyst activity, fuel inlet temperature, current density, and operating pressure has been studied. Increasing the operating pressure is shown to be an effective way of reducing both the local cooling caused by the reforming reactions and the overall temperature increase across the cell. Simulations for both counter-flow and co-flow configurations have been performed and compared.     

SOFC内部重整反应与电化学反应耦合机理

以经过预重整反应的混合气为原料的固体氧化物燃料电池（SOFC）内部,甲烷蒸气重整反应与电化学反应同时发生在阳极多孔介质中,二者受到不同的操作与设计参数的影响,对电池总体性能起着决定性作用。编制了三维数值模拟程序,对由多孔阳极层、气体流动管道、固体支撑平板构成的单个复合管道进行了研究。结果显示：重整反应主要发生在多孔材料靠近流动管道的薄层内,只有靠近管道入口处才能在较深处进行;电化学反应发生在多孔层与电解质的交界面处;重整反应生成的H2、CO扩散到多孔材料底部参加电化学反应;电化学反应生成的热量供重整反应使用。说明研究范围内,SOFC阳极复合通道具有较好的传热、传质性能,化学/电化学反应存在较好的耦合关系。     

Alternative concept for SOFC with direct internal reforming operation: Benefits from inserting catalyst rod

Mathematical models of direct internal reforming solid oxide fuel cell (DIR‐SOFC) fueled by methane are developed using COMSOL® software. The benefits of inserting Ni‐catalyst rod in the middle of tubular‐SOFC are simulated and compared to conventional DIR‐SOFC. It reveals that DIR‐SOFC with inserted catalyst provides smoother temperature gradient along the system and gains higher power density and electrochemical efficiency with less carbon deposition. Sensitivity analyses are performed. By increasing inlet fuel flow rate, the temperature gradient and power density improve, but less electrical efficiency with higher carbon deposition is predicted. The feed with low inlet steam/carbon ratio enhances good system performances but also results in high potential for carbon formation; this gains great benefit of DIR‐SOFC with inserted catalyst because the rate of carbon deposition is remarkably low. Compared between counter‐ and co‐flow patterns, the latter provides smoother temperature distribution with higher efficiency; thus, it is the better option for practical applications. © 2009 American Institute of Chemical Engineers AIChE J, 2010     

Simulation of autothermal reforming in a staged‐separation membrane reactor for pure hydrogen production

Steam methane reforming with oxygen input is simulated in staged‐separation membrane reactors. The configuration retains the advantage of regular membrane reactors for achieving super‐equilibrium conversion, but reaction and membrane separation are carried out in two separate units. Equilibrium is assumed in the models given the excess of catalyst. The optimal pure hydrogen yield is obtained with 55% of the total membrane area allocated to the first of two modules. The performance of the process with pure oxygen input is only marginally better than with air. Oxygen must be added in split mode to reach autothermal operation for both reformer modules, and the oxygen input to each module depends on the process conditions. The effects of temperature, steam‐to‐carbon ratio and pressure of the reformer and the area of the membrane modules are investigated for various conditions. Compared with a traditional reformer with an ex situ membrane purifier downstream, the staged reactor is capable of much better pure hydrogen yield for the same autothermal reforming operating conditions.     

Cooling of a Diesel Reformate Fuelled Solid Oxide Fuel Cell by Internal Reforming of Methane: A Modelling Study

In this paper a system combining a diesel reformer using catalytic partial oxidation (CPOX) with the Solid Oxide Fuel Cell (SOFC) for Auxiliary Power Unit (APU) applications is modeled with respect to the cooling effect provided by internal reforming of methane in anode gas channel. A model mixture consisting of 80% n-hexadecane and 20% 1-methylnaphthalin is used to simulate the commercial diesel. The modelling consists of several steps. First, equilibrium gas composition at the exit of CPOX reformer is modelled in terms oxygen to carbon (O/C) ratio, fuel utilization ratio and anode gas recirculation. Second, product composition, especially methane content, is determined for the methanation process at the operating temperatures ranging from 500 ℃ to 520 ℃. Finally, the cooling power provided by internal reforming of methane in SOFC fuel channel is calculated for two concepts to increase the methane content of the diesel reformate. The results show that the first concept, operating the diesel reformer at low O/C ratio and/or recirculation ratio, is not realizable due to high probability of coke formation, whereas the second concept, combining a methanation process with CPOX, can provide a significant cooling effect in addition to the conventional cooling concept which needs higher levels of excess air.     

Modeling of a SOFC fuelled by methane: From direct internal reforming to gradual internal reforming

Natural gas appears to be a fuel of great interest for SOFC systems. The principal component of natural gas is methane, which can be converted into hydrogen by direct or gradual internal reforming (DIR or GIR) within the SOFC anode. However, DIR requires a large amount of steam to produce hydrogen. If the injected mixture contains very small quantities of steam, GIR is then obtained. With GIR, the risk of carbon formation is even greater. This paper proposes a model and simulation, using the CFD-Ace software package, of the behaviour of a tubular SOFC using GIR and a comparison between utilization in DIR and GIR. A thermal study is included in the model and a detailed thermodynamic analysis is carried out to predict the carbon formation boundary for SOFCs fuelled by methane. Thermodynamic equilibrium calculations taking into account Boudouard and methane cracking reactions allowed us to investigate the occurrence of carbon formation. Simulations were used to calculate the distributions of partial pressures for all the gas species (CH₄, H₂, CO, CO₂, H₂O), current densities and potentials in both electronic and ionic phases within the anode part (i.e., gas channel and cermet anode). The simulations indicate that there is no decrease in electrochemical performance if GIR is used rather than DIR. A thermal study appears to confirm that the cooling effect due to the endothermic reforming reaction is eliminated in GIR, but the thermodynamic study indicates that carbon formation can be suspected for x_H2O/x_CH4 ratios lower than one.     

Development of a novel test system for in situ catalytic, electrocatalytic and electrochemical studies of internal fuel reforming in solid oxide fuel cells

A test system based around a thin‐walled extruded solid electrolyte tubular reactor has been developed, which enables the fuel reforming catalysis and surface chemistry occurring within solid oxide fuel cells and the electrochemical performance of the fuel cell to be studied under genuine operating conditions. It permits simultaneous monitoring of the catalytic chemistry and the cell performance, allowing direct correlation between the fuel cell performance and the reforming characteristics of the anode, as well as enabling the influence of drawing current on the catalysis and surface reaction pathways to be studied. Temperature‐programmed reaction measurements can be carried out on anodes in an actual SOFC, and have been used to investigate the reduction characteristics of different anode formulations, methane activation and methane steam reforming, and to evaluate the nature and level of carbon deposition on the anode during reforming. This revised version was published online in July 2006 with corrections to the Cover Date.     

Investigation of a proton-conducting SOFC with internal autothermal reforming of methane

This study presents a performance analysis of a proton-conducting SOFC (SOFC-H⁺) with internal reforming of methane. The autothermal reforming within the SOFC-H⁺ stack is considered to be a potential solution of the carbon formation problem facing in operation of internal steam reforming SOFC-H⁺. A one-dimensional, steady-state model of the SOFC-H⁺ coupled with a detailed electrochemical model is employed to investigate its performance in terms of power density and fuel cell efficiency. The simulation results show that when SOFC-H⁺ is operated under an autothermal reforming environment, the presence of carbon monoxide, which is a major cause of carbon formation, in the fuel cell stack decreases. Effect of key operating parameters, such as temperature, steam-to-carbon and oxygen-to-carbon feed ratios, current density and fuel utilization, on the SOFC-H⁺ performance in terms of electrical efficiencies and energy demand is also investigated. The results indicate that operating temperatures have strong influence on SOFC-H⁺ performance, carbon monoxide production and heat generation.     

Model‐based optimization of hydrogen generation by methane steam reforming in autothermal packed‐bed membrane reformer

An autothermal membrane reformer comprising two separated compartments, a methane oxidation catalytic bed and a methane steam reforming bed, which hosts hydrogen separation membranes, is optimized for hydrogen production by steam reforming of methane to power a polymer electrolyte membrane fuel cell (PEMFC) stack. Capitalizing on recent experimental demonstrations of hydrogen production in such a reactor, we develop here an appropriate model, validate it with experimental data and then use it for the hydrogen generation optimization in terms of the reformer efficiency and power output. The optimized reformer, with adequate hydrogen separation area, optimized exothermic‐to‐endothermic feed ratio and reduced heat losses, is shown to be capable to fuel kW‐range PEMFC stacks, with a methane‐to‐hydrogen conversion efficiency of up to 0.8. This is expected to provide an overall methane‐to‐electric power efficiency of a combined reformer‐fuel cell unit of ～0.5. Recycling of steam reforming effluent to the oxidation bed for combustion of unreacted and unseparated compounds is expected to provide an additional efficiency gain. © 2010 American Institute of Chemical Engineers AIChE J, 2011     

基于天然气自热重整的SOFC系统性能分析

建立一个天然气自热重整的固体氧化物燃料电池(SOFC)系统模型,利用Aspen Plus化工流程模拟软件链接基于Fortran语言编写的电堆模型,在质量守恒和能量守恒的基础上,分析不同参数对系统性能的影响。模拟结果表明:随着水碳比的增加,甲烷和一氧化碳的转化率增大,导致氢气和二氧化碳含量增加;氧碳比和系统效率在水碳比为1.5时达到最大。随着燃料利用率的增加,电流密度增大,导致空气过量系数增大,空气利用率降低;系统的总效率和净效率均随之增大。尾气温度随着水碳比和燃料利用率的增加均呈现下降趋势。系统的最大总效率和净效率分别为44.5%和39.2%。研究结果为进一步优化自热重整系统指明了方向。     

SOFC fuelled by methane without coking: optimization of electrochemical performance

In recent years, fuel cell technology has attracted considerable attention from several fields of scientific research as fuel cells produce electric energy with high efficiency, emit little noise, and are non-polluting. Solid oxide fuel cells (SOFCs) are particularly important for stationary applications due to their high operating temperature (1,073–1,273 K). Methane appears to be a fuel of great interest for SOFC systems because it can be directly converted into hydrogen by direct internal reforming (DIR) within the SOFC anode. Unfortunately, internal steam reforming in SOFC leads to inhomogeneous temperature distributions which can result in mechanical failure of the cermet anode. Moreover this concept requires a large amount of steam in the fed gas. To avoid these problems, gradual internal reforming (GIR) can be used. GIR is based on local coupling between steam reforming and hydrogen oxidation. The steam required for the reforming reaction is obtained by the hydrogen oxidation. However, with GIR, Boudouard and cracking reactions can involve a risk of carbon formation. To cope with carbon formation a new cell configuration of SOFC electrolyte support was studied. This configuration combined a catalyst layer (0.1%Ir–CeO₂) with a classical anode, allowing GIR without coking. In order to optimise the process a SOFC model has been developed, using the CFD-Ace+ software package, and including a thin electrolyte. The impact of a thin electrolyte on previous conclusions has been assessed. As predicted, electrochemical performances are higher and carbon formation is always avoided. However a sharp decrease in the electrochemical performances appears at high current densities due to steam clogging.     

固体氧化物燃料电池燃料重整技术研究进展

对固体氧化物燃料电池(SOFC)燃料重整技术的研究进展进行了综述。分别对催化裂解、蒸气重整、部分氧化、自供热重整等燃料外部重整技术,以及直接氧化和直接蒸气内部重整等内部重整技术的研究进展进行了评述,对每种重整方式的特点进行了介绍,并展望了其今后的发展趋势。     

Catalytic aspects of the steam reforming of hydrocarbons in internal reforming fuel cells

Steam reforming of hydrocarbons such as natural gas is an attractive method of producing the hydrogen fuel gas required by fuel cells. It may be carried out external to the fuel cell or internally. The two types of fuel cell in which internal reforming is most appropriate are the molten carbonate (MCFC), operating at ca. 650°C and the solid oxide (SOFC) which currently operates above 800°C. At such temperatures, the heat liberated by the electrochemical reactions within the cell can be utilised by the endothermic steam reforming reaction. This paper reviews some of the catalytic aspects of internal reforming in these two types of cell. In the MCFC the major catalyst issue is that of long term activity in the presence of a corrosive alkaline environment produced by the cell's electrolyte. In Europe, this is being addressed by British Gas and others, in a programme part-funded by the European Commission. In this programme, potential catalysts for the direct internal reforming MCFC were evaluated in ‘out-of-cell’ tests. This has led to the demonstration of a 1 kW proof-of-concept DIR-MCFC stack and the start of a European ‘Advanced DIR-MCFC’ project. For the SOFC, it has been shown that state-of-the-art nickel cermet anodes can provide sufficient activity for steam reforming without the need for additional catalyst. However, anode degradation may occur when steam reforming is carried out for long periods. New anode materials could therefore offer significant benefits.     

Fuel processing in direct propane solid oxide fuel cell and carbon dioxide reforming of propane over Ni-YSZ

This work is aimed at understanding the reaction mechanism of propane internal reforming in the solid oxide fuel cell (SOFC). This mechanism is important for the design and operation of SOFC internal processing of hydrocarbons. An anode-supported SOFC unit with Ni-YSZ anode operating at 800 °C was tested with direct feeding of 5% propane. CO₂ reforming of propane was carried out in a reactor with Ni-YSZ catalyst to simulate internal propane processing in SOFC. The performance of this direct propane SOFC is stable. The C specie formed over the anode functional layer of SOFC can be completely removed. The major gas products of SOFC are H₂, CO, CH₄, C₂H₄ and CO₂. Pseudo-steady-state internal processing of propane in the anode catalytic layer of SOFC is associated with a CO₂/C₃H₈ molar ratio of about 1.26 and basically CO₂ reforming of propane. CO₂ dissociation to produce the O species to oxidize the C species from dehydrogenation and dissociation of propane and its fragments should be the major reaction during CO₂ reforming of propane.     

Steady-state modeling and bifurcation behavior of circulating fluidized bed membrane reformer-regenerator for the production of hydrogen for fuel cells from heptane

The production of hydrogen for fuel cells by steam reforming of heptane is investigated in a Circulating Fluidized Bed Membrane Reformer-Regenerator (CFBMRR) system (A.I.Ch.E. Journal 49(5) (2003) 1250). Palladium based hydrogen permselective membranes are used for hydrogen removal and dense perovskite oxygen permselective membranes are used for oxygen introduction. A series of pseudo-steady-state simulations show that when the catalyst is not regenerated, the circulating nickel reforming catalyst deactivates quickly and the “half catalyst activity life” for efficient production of hydrogen is quite short, especially at high temperatures. Efficient continuous catalyst regeneration can keep the catalyst activity high (∼1.0). With continuous catalyst regeneration, autothermal operation for the entire adiabatic reformer-regenerator system is achievable when the exothermic heat generated from the catalyst regenerator is sufficient to compensate for the endothermic heat consumed in the riser reformer. This type of autothermal operation becomes less likely at high steam to carbon feed ratios. This is due to the fact that carbon deposition rate decreases leading to the decrease of autothermal circulating feed temperature and energy-based hydrogen yield (adiabatic hydrogen yield in autothermal reformer-regenerator system). Multiplicity of the steady states for the reformer is possible for this configuration. With the steam to carbon feed ratio as the bifurcation parameter, multiplicity occurs between the two bifurcation points 1.444 and 2.251 mol/mol. In this multiplicity region, the energy-based hydrogen yield at the upper steady state with high regenerator output temperature is surprisingly the lowest one. While it is the highest one at the lower steady state with low regenerator output temperature. The maximum energy-based hydrogen yield is about 15.58 moles of hydrogen per mole of heptane fed at the lower steady-state when steam to carbon feed ratio is very close to the bifurcation value of 1.444 mol/mol. After removing the sweep gas steam by downstream cooling and de-humidification, the product hydrogen from steam reforming of hydrocarbons can be used for fuel cells with high purity (∼100%).     

甲烷自热重整制合成气热力学平衡分析

使用1stOpt2.5计算软件编程计算甲烷自热重整制合成气反应平衡组成,考察温度、原料比对体系组分平衡的影响。通过计算结果指出最适宜的反应条件,为甲烷自热重整制合成气催化剂的研究与开发提供热力学依据。     

Analysis of hydrogen production from methane autothermal reformer with a dual catalyst-bed configuration

This paper presents a performance analysis of a dual-bed autothermal reformer for hydrogen production from methane using a non-isothermal, one dimensional reactor model. The first section of Pt/Al₂O₃ catalyst is designed for oxidation reaction, whereas the second one based on Ni/MgAl₂O₄ catalyst involves steam reforming reaction. The simulation results show that the dual-bed autothermal reactor provides higher reactor temperature and methane conversion compared with a conventional fixed-bed reformer. The H₂O/CH₄ and O₂/CH₄ feed ratios affect the methane conversion and the H₂/CO product ratio. The addition of steam at lower temperatures to the steam reforming section of the dual-bed reactor can produce the synthesis gas with a higher H₂/CO product ratio.     

Effect of Anode off‐gas Recycling on Reforming of Natural Gas for Solid Oxide Fuel Cell Systems

The effect of anode off‐gas recycling (AOGR) on the characteristic performance of a natural gas reformer equipped with a precious metal catalyst is investigated experimentally. The reformer is operated both with synthetic AOGR gas and in steam reforming (SR) conditions. The characteristic performance in SR and AOGR mode are compared with equilibrium, and it is found that equilibrium is more readily achieved in AOGR mode. The reformer is used for extended periods of time (100–1,000 h) in conditions where carbon formation is thermodynamically possible to measure any changes in characteristic performance. No significant change in the performance is observed due to carbon formation or catalyst deactivation. The reformer could be successfully implemented in a 10 kW SOFC system with an anode off‐gas recycling loop.     

Electrocatalytic reforming of carbon dioxide by methane in SOFC system

The reaction of carbon dioxide catalytic reforming with methane is an attractive route because these greenhouse gases can be converted into variable feedstocks. However this reaction is a highly energy consuming and coke forming process. These problems were improved by the electrocatalytic reforming of CO₂ with CH₄ in a solid oxide fuel cell (SOFC) membrane reactor system, which generates high electrical power and synthesis gases. The single cell consists of catalyst electrode (NiO–MgO), counter electrode ((La,Sr)MnO₃) and Y₂O₃ stabilized ZrO₂ (YSZ) electrolyte. The reaction rates of CO₂ and CH₄, and the electrochemical properties were investigated by an on-line GC and impedance-analyzer under open- and closed-circuit conditions, respectively. It was found that reaction rates of CO₂ and CH₄ under the closed-circuit condition were more stable than those of the open-circuit. The results were interpreted that the stability of catalyst anode was maintained by the reaction of oxygen ion transferred from the cathode with the surface carbon formed in the internal CO₂ reforming by CH₄ in SOFC system.     

Effect of precious metal addition to Ni-YSZ cermet on reforming of CH4 and electrochemical activity as SOFC anode

Various kinds of precious metals were added to the Ni-Y₂O₃-stabilized zirconia (Ni-YSZ) cermets, and the relation between steam reforming of CH₄ and the electrochemical activity as a solid oxide fuel cell (SOFC) anode was investigated. Ru and Pt additions promoted the reforming and suppressed the coke depositions. The electrochemical activity of the SOFC anode was enhanced by the addition of Ru and Pt, indicating that these precious metals effectively functioned as the anode catalysts. The impedance related to gas diffusion was greatly reduced, indicating that stability of the anode catalyst of SOFC was considerably improved since coke was hardly deposited.