Inhibited transesterification and enhanced fibrillation of TLCP by nano-SiO2 in polycarbonate matrix

Hybrid composites composed of a thermotropic liquid crystalline polymer (TLCP), nano-SiO₂ and polycarbonate (PC) were prepared by melt blending in a twin-screw extruder. Infrared spectroscopy analysis indicated that the transesterification between PC and TLCP molecules during melt blending was significantly reduced in TLCP/PC blends filled with nano-SiO₂, compared to the unfilled TLCP/PC one. Scanning electron microscopy (SEM) observation showed that better compatibility and finer TLCP dispersion were reached in the unfilled blend, which made the fibrillation of TLCP difficult in capillary flow even at high shear rate. In contrast to this, well-developed TLCP fibrils were formed by capillary flow in nano-SiO₂ filled TLCP/PC blends. By increasing the nano-SiO₂ concentration and shear rate, the fibrillation of TLCP was significantly enhanced. Thermodynamically the interfacial tension between these components and dynamically the viscosity ratio of TLCP to PC were used to investigate the mechanism of nano-SiO₂ in inhibiting the transesterification and enhancing the fibrillation of TLCP droplets in these hybrid composites.     

Pickering emulsion polymerization: Preparation of polystyrene/nano-SiO2 composite microspheres with core-shell structure

Polystyrene/nano-SiO₂ composite microspheres (PS/nano-SiO₂) with core-shell structure were successfully synthesized in a Pickering emulsion route using nano-SiO₂ particles as stabilizers, which were organically modified by methacryloxypropyltrimethoxysilane (MPTMS) which containing a reactive CC bond. The products were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), fourier transformation infrared spectrum (FTIR), thermogravimetric analysis (TGA) and X-ray photoelectron spectroscopy (XPS). In addition, bare PS spheres could also be obtained by changing synthetic conditions. It was found that the morphology of the resulting products depends on particle concentration, particle wettability and pH value of particle dispersion. A possible mechanism for the formation of the composites with different morphologies is proposed.     

Preliminary study on the water permeability and microstructure of concrete incorporating nano-SiO2

Water permeability resistant behavior and microstructure of concrete with nano-SiO₂ were experimentally studied. A water permeability test shows that, for concretes of similar 28-day strength, the incorporation of nano-SiO₂ can improve the resistance of water penetration of concrete. An ESEM test reveals that the microstructure of concrete with nano-SiO₂ is more uniform and compact than that of normal concrete. Mechanism about the effect of nano-SiO₂ on concrete is described.     

Studying the role of polysiloxane additives and nano-SiO2 on the mechanical properties of a typical acrylic/melamine clearcoat

Effects of conventional polysiloxane additives and nano-SiO₂ on the mechanical properties of an automotive acrylic/melamine clearcoat (CC) are studied. Clearcoats formulations were prepared by addition of different concentrations of polysioloxane additives (with different modifications) and hydrophobic nano-SiO₂ particles. Attenuated Total Reflection-Fourier Transform Infrared (ATR-FTIR) and atomic force microscope (AFM) were utilized to evaluate the effects of nano-SiO₂ and polysiloxane additives on the surface properties of the CCs. The mechanical properties of the surface and the bulk of the CCs were studied by nano-indentation and tensile tests, respectively. Results showed that polysiloxane additives can mostly affect the mechanical properties of the surface of the CC. Additives with shorter side chains and therefore higher surface activity caused higher changes on the surface properties the CC. Unlike conventional polysiloxane additives, the nano-SiO₂ particles mainly influenced the mechanical properties of the bulk of the CC.     

Performance characteristics of high-volume Class F fly ash concrete

More than 88 million tonnes of fly ash is generated in India each year. Most of the fly ash is of Class F type. The percentage utilization is around 10 to 15%. To increase its percentage utilization, an extensive investigation was carried out to use it in concrete. This article presents the results of an experimental investigation dealing with concrete incorporating high volumes of Class F fly ash. Portland cement was replaced with three percentages (40%, 45%, and 50%) of Class F fly ash. Tests were performed for fresh concrete properties: slump, air content, unit weight, and temperature. Compressive, splitting tensile, and flexural strengths, modulus of elasticity, and abrasion resistance were determined up to 365 days of testing.Test results indicated that the use of high volumes of Class F fly ash as a partial replacement of cement in concrete decreased its 28-day compressive, splitting tensile, and flexural strengths, modulus of elasticity, and abrasion resistance of the concrete. However, all these strength properties and abrasion resistance showed continuous and significant improvement at the ages of 91 and 365 days, which was most probably due to the pozzolanic reaction of fly ash. Based on the test results, it was concluded that Class F fly ash can be suitably used up to 50% level of cement replacement in concrete for use in precast elements and reinforced cement concrete construction.     

Effect of steam curing on class C high-volume fly ash concrete mixtures

The effect of steam curing on concrete incorporating ASTM Class C fly ash (FA), which is widely available in Turkey, was investigated. Cement was replaced with up to 70% fly ash, and concrete mixtures with 360 kg/m³ cementitious content and a constant water/binder ratio of 0.4 were made. Compressive strength of concrete, volume stability of mortar bar specimens, and setting times of pastes were investigated. Test results indicate that, under standard curing conditions, only 1-day strength of fly ash concrete was low. At later ages, the strength values of even 50% and 60% fly ash concretes were satisfactory. Steam curing accelerated the 1-day strength but the long-term strength was greatly reduced. Setting time of fly ash-cement pastes and volume stability of mortars with 50% or less fly ash content were found to be satisfactory for standard specimens. In addition, for steam curing, this properties were acceptable for all replacement ratios.     

Study on coal chars combustion under O2/CO2 atmosphere with fractal random pore model

When predicting the variation of pore structure during O₂/CO₂ combustion of coal chars using the random pore model (RPM), it is impossible to calculate exactly the structure parameter ψ from the pore characteristics. The values of structure parameter ψ, which were calculated based on its fractal feature at various carbon conversions, should be almost constant. However, this investigation exhibited a drastic increase of ψ at the end of combustion reaction. In this work, structure parameter ψ of the RPM was modified according to the experimental analysis and a new model, fractal random pore model (FRPM), was constructed. Compared with other models such as RPM, discrete random pore model (DRPM), the Struis model (Model I) and the Liu model (Model II), it was found that fractal random pore model was more accurate to describe coal chars combustion, especially at higher conversions. Using the FRPM, O₂/CO₂ isotherm combustion of coal chars were analyzed at different temperatures.     

The catalytic performance in oxidative coupling of methane and the surface basicity of La2O3, Nd2O3, ZrO2 and Nb2O5

The catalytic performance in oxidative coupling of methane (OCM) of unmodified pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ has been investigated under various conditions. The results confirmed that the activity of La₂O₃ and Nd₂O₃ was always much higher than that of the remaining two. The surface basicity/base strength distribution of pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ was measured using a test reaction of transformation of 2-butanol and a temperature-programmed desorption of CO₂. Both methods showed that La₂O₃ and Nd₂O₃ had high basicity and contained medium and strong basic sites (lanthanum oxide more and neodymium oxide somewhat less). ZrO₂ had only negligible amount of weak basic sites and Nb₂O₅ was rather acidic. The confrontation of the basicity and catalytic performance indicated that in the case of investigated oxides, the basicity (especially strong basic sites) could be a decisive factor in determination of the catalytic activity in OCM. Only in the case of ZrO₂ it was observed a moderate catalytic performance in spite of negligible basicity. The influence of a gas atmosphere used in the calcination of oxides (flowing oxygen, helium and nitrogen) on their basicity and catalytic activity in OCM had been also investigated. Contrary to earlier observations with MgO, no effect of calcination atmosphere on the catalytic performance of investigated oxides in OCM and on their basicity was observed.     

Improvement of coke resistance of Ni/Al2O3 catalyst in CH4/CO2 reforming by ZrO2 addition

This work investigates the improvement of Ni/Al₂O₃ catalyst stability by ZrO₂ addition for H₂ gas production from CH₄/CO₂ reforming reactions. The initial effect of Ni addition was followed by the effect of increasing operating temperature to 500–700 °C as well as the effect of ZrO₂ loading and the promoted catalyst preparation methods by using a feed gas mixture at a CH₄:CO₂ ratio of 1:1.25. The experimental results showed that a high reaction temperature of 700 °C was favored by an endothermic dry reforming reaction. In this reaction the deactivation of Ni/Al₂O₃ was mainly due to coke deposition. This deactivation was evidently inhibited by ZrO₂, as it enhances dissociation of CO₂ forming oxygen intermediates near the contact between ZrO₂ and nickel where the deposited coke is gasified afterwards. The texture of the catalyst or BET surface area was affected by the catalyst preparation method. The change of the catalyst texture resulted from the formation of ZrO₂–Al₂O₃ composite and the plugging of Al₂O₃ pore by ZrO₂. The 15% Ni/10% ZrO₂/Al₂O₃ co-impregnated catalyst showed a higher BET surface area and catalytic activity than the sequentially impregnated catalyst whereas coke inhibition capability of the promoted catalysts prepared by either method was comparable. Further study on long-term catalyst stability should be made.     

Electrocatalytic activity of IrO2-RuO2 supported on Sb-doped SnO2 nanoparticles

Electrocatalytic IrO₂-RuO₂ supported on Sb-doped SnO₂ (ATO) nanoparticles is very active towards the oxygen evolution reaction. The IrO₂-RuO₂ material is XRD amorphous and exists as clusters on the surface of the ATO. Systematic changes to the surface chemical composition of the ATO as a function of the IrO₂:RuO₂ ratio suggests an interaction between the IrO₂-RuO₂ and ATO. Cyclic voltammetry indicates that the electrochemically active surface area of IrO₂-RuO₂ clusters is maximised when the composition is 75 mol% IrO₂-25 mol% RuO₂. Decreasing the loading of IrO₂-RuO₂ on ATO reduces the electrochemically active surface area, although there is evidence to support a decrease in the clusters size with decreased loading. Tafel slope analysis shows that if the clusters are too small, the kinetics of the oxygen evolution reaction are reduced. Overall, clusters of IrO₂-RuO₂ on ATO have similar or better performance for the oxygen evolution reaction than many previously reported materials, despite the low quantity of noble metals used in the electrocatalysts. This suggests that these oxides may be of economic advantage if used as PEM water electrolysis anodes.     

Fabrication and characterization of nanoporous SiO2 ceramics via pyrolysis of silicone resin filled with nanometer SiO2 powders

Mesoporous SiO₂ ceramics are fabricated by pyrolysis of silicone resin filled with nanometer SiO₂ powders in air at 1273 K. With the increase of shaping pressure, open porosity and average pore size decrease, while bulk density and fracture strength are improved. The fracture surface of porous SiO₂ ceramics was observed.     

Properties of sol-gel SnO2/TiO2 electrodes and their photoelectrocatalytic activities under UV and visible light illumination

A visible light active binary SnO₂-TiO₂ composite was successfully prepared by a sol-gel method and deposited on Ti sheet as a photoanode to degrade orange II dye. Titanium and SnO₂ can promote the development of rutile phase of TiO₂ and inhibit the formation of anatase phase of TiO₂. Formation of SnO₂ crystalline is insignificant even when the calcination temperature increases to 700 °C. Heterogenized interface between SnO₂ and TiO₂ inhibits growth of TiO₂ linkage and leads to the particle-filled surface morphology of SnO₂-containing films. The carbonaceous, Ti-O-C bonds and Ti³⁺ species are likely to account for the photoabsorption and photoelectrocatalytic (PEC) activity under visible light illumination. The electrode with 30% SnO₂ exhibits higher photocurrent when compared with those in the region of 0-50%. The 600 °C-calcined SnO₂-TiO₂ electrode indicates higher activity when compared with those at 400, 500, 700 and 800 °C. PEC degradation of orange II follows the Langmuir-Hinshelwood model and takes place much effectively in a solution of pH 3.0 than those in pH 7.0 and pH 11.0.     

Influence of TiO2 and CeO2 on the hydrogenation activity of bulk Ni2P

TiO₂- and CeO₂-promoted bulk Ni₂P catalysts were prepared by impregnation and in-situ H₂ temperature-programmed reduction method. The prepared catalysts were characterized by XRD and XPS. The hydrogenation activities of the catalysts were studied using 1.5 wt.% 1-heptene in toluene and 1.0 wt.% phenylacetylene in ethanol as the model feeds. The results indicate that bulk Ni₂P possesses low hydrogenation activity but is tunable by simply controlling the content of the additives (TiO₂ or CeO₂), suggesting that TiO₂ and CeO₂ are effective promoters to enhance the hydrogenation activity of Ni₂P.     

Electrochemical characteristics of porous TiO2 encapsulated silicon anode

TiO₂ coated silicon, which was prepared by the modified sol–gel method, was employed as the anode material for lithium secondary batteries and the relationship between the diffusivity and electrochemical characteristics was investigated. The results showed that the physical properties of the samples, such as their diffusivity and pore size distribution, enhanced the cycling efficiency of the TiO₂ coated silicon, probably due to the reduction of the side reactions, which may be closely related to the pore size distribution of the TiO₂ coating layer. The pore size of the coating layer plays an important role in retarding the lithium ion diffusion. In the experimental range studied herein, higher capacity retention was exhibited for the TiO₂ coated silicon prepared at pH 10.7.     

XANES study of polyaniline-V2O5 and sulfonated polyaniline-V2O5 nanocomposites

In this work, two materials for secondary lithium battery cathodes formed by polyaniline-V₂O₅ and sulfonated polyaniline-V₂O₅, which have a higher charge capacity than the V₂O₅ xerogel, were synthesized. X-ray absorption and Fourier transform infrared spectroscopies were employed to analyze the short-range interactions in these materials. Based on these experiments, it was possible to observe significant differences in the symmetry of the VO₅ units, and this was attributed to the intimate contact between V₂O₅ and the polymers, and to some flexibility of the VO₅ square pyramids due to the low range order of the nanocomposites.     

Preparation of columbite MgNb2O6 and ZnNb2O6 ceramics by reaction-sintering

Columbite MgNb₂O₆ (MN) and ZnNb₂O₆ (ZN) ceramics produced by the reaction-sintering process were investigated. Secondary phases Mg_0.652Nb_0.598O_2.25 and Mg_0.66Nb_11.33O₂₉ were found in MgNb₂O₆ pellets. After 1250 °C sintering for 2 h, a density 4.85 g/cm³ (97.1% of the theoretical value) was obtained in MgNb₂O₆ pellets. In ZnNb₂O₆ pellets, no secondary phase formed. The maximum density 5.55 g/cm³ (98.7% of the theoretical value) occurs at 1200 and 1180 °C sintering for 2 and 4 h, respectively.     

Properties of char particles obtained under O2/N2 and O2/CO2 combustion environments

Pulverized coal combustion in O₂/N₂ and O₂/CO₂ environments was investigated with a drop tube furnace. Results present that the reaction rate and burn-out degree of O₂/CO₂ chars (obtained in O₂/CO₂ environments) are lower than that of O₂/N₂ chars (obtained in O₂/N₂ environments) under the same experimental condition. It indicates that a higher O₂ concentration in O₂/CO₂ environment is needed to achieve the similar combustion characteristic to that in O₂/N₂ environment. The main differences between O₂/N₂ and O₂/CO₂ chars rely on the pore structure determined by N₂ adsorption and chemical structure measured by FT-IR. For O₂/CO₂ char, the surface is thick and the pores are compact which contribute to the fragmentation reduction of particles burning in O₂/CO₂ environment. The organic functional group elimination rate from the surface of O₂/CO₂ chars is slower or delayed. The present research results might have important implications for further understanding the intrinsic kinetics of pulverized coal combustion in O₂/CO₂ environment.     

Laser stereolithography of ZrO2 toughened Al2O3

Ceramic laser stereolithography is a manufacturing process suitable candidate for the production of complex shape technical ceramics. The green ceramic is produced layer by layer through laser polymerisation of UV curable ceramic suspensions. A number of critical issues deserve attention: high solid loading and low viscosity of the suspensions, high UV reactivity, prevention of interlayer delamination in the green and in the sintered body, good mechanical performance. In this work, ZrO₂-reinforced Al₂O₃ components have been obtained from an acrylic modified zircon loaded with alumina powders. The zircon compound is effective as organic photoactivated resin and allows the dispersion of a high volume fraction of Al₂O₃ powder (up to 50 vol.%) while keeping viscosity at reasonable low values. The zircon compound also represents a liquid ceramic precursor that converts to oxide after burning out of the binder. Thank to the good dispersion of the alumina powder in the zircon acrylate, a uniform dispersion of ZrO₂ submicron particles is obtained after pyrolysis. These are located at the grain boundaries between alumina grains. Formation of both monoclinic and tetragonal ZrO₂ occurs as evidenced by XRD. No delamination occurs in bending tests as evidenced by SEM fractography, satisfactory modulus and strength values were concurrently found.