共查询到20条相似文献,搜索用时 125 毫秒
1.
采用透射电子显微镜研究了Zn元素对退火态3003铝合金微观组织的影响,并用拉伸试验和电化学极化实验,分别研究了Zn元素对3003铝合金力学性能和电化学腐蚀性能的影响.透射电镜观察和电子拉伸实验结果表明,Zn元素加入3003铝合金,可以细化退火态合金中的析出相,使其分布更加弥散,尺寸更加均匀.Zn元素的加入,可使退火态合... 相似文献
2.
3.
4.
5.
6.
7.
5052铝合金板材生产工艺研究 总被引:1,自引:0,他引:1
重点介绍了5052铝合金板材的应用及其生产工艺控制,并对5052合金板材的组织结构、力学性能进行了分析.通过一定厚度板材的等时退火,确定了5052合金再结晶退火温度. 相似文献
8.
9.
10.
11.
机械合金化制备W-Ni-Cu纳米复合粉末的研究 总被引:1,自引:0,他引:1
采用机械合金化(MA)制备W—Ni—Cu纳米复合粉末,对粉末的晶粒尺寸、粒度、松装密度、振实密度进行了测定和分析,并研究了过程控制剂(PCA)对粉末性能的影响。 相似文献
12.
烧结铁基材料的淬火处理 总被引:4,自引:0,他引:4
综述了烧结铁基材料的热处理特点,合金元素、粉末类型、添加剂形式、加热介质、淬火介质和回火温度等因素对热处理烧结铁基材料力学性能的影响。 相似文献
13.
14.
Methods for obtaining alloys of the Cu-Mn-Ni system with the preliminary mechanical alloying of the components and by direct alloying are compared. It is established that the first technology provides substantially lower waste of manganese (about by a factor of two) than the second one, which is highly important to produce solders with strongly controllable additives. It is shown that, as the treatment time of mechanically alloying materials increases, their temperature properties correspond to alloys obtained by direct alloying the components. The proposed method seems to be promising for production of relatively small amounts of alloys of components which differ in density, melting point, volatility, interaction with gases, and other physical-mechanical properties. 相似文献
15.
利用合金化手段改善高硅钢及快凝薄带的组织性能。通过OM、XRD、VSM等研究了铝、硼、铌等合金元素对其组织织构、力学性能和磁性能的影响。结果表明,合金化能够改善铸态高硅钢的强韧性。在快凝薄带状态,铝元素会增大其晶粒尺寸并增强{100}和{114}<221>方向的织构,降低磁导率和磁滞损耗。 相似文献
16.
17.
18.
19.
Wire-Based Friction Stir Processing as a Novel Pathway for Solid-State Surface Alloying of Magnesium
Sabzevar M. Zahiri Mousavizade S. M. Pouranvari M. 《Metallurgical and Materials Transactions A》2021,52(11):4737-4741
Wire-based friction stir processing is introduced as a solid-state surface alloying strategy for surface alloying of AZ31 magnesium alloy with aluminum, as a key alloying element in magnesium alloys. This technique enables the formation of a defect-free, grain refined and alloyed surface with the increased volume fraction of Mg-Al second phase, and thus, enhanced surface hardness. This simple technique provides a solid-state surface alloying pathway to improve the surface properties of the metallic materials.
相似文献