Using ARB process as a solution for dilemma of Si and SiCp distribution in cast Al-Si/SiCp composites

A major challenge in achieving the best potential of SiC_p-reinforced aluminum composites is to homogeneously disperse SiC particles within the aluminum alloys. The presence of coarse Si fibers with non-uniform distribution in cast Al-Si alloys, which may lead to poor mechanical properties, is another important problem that limits the application of these alloys. In order to eliminate these problems, accumulative roll bonding (ARB) process was used in this study as a very effective method for improving the microstructure and mechanical properties of the Al356/SiC_p composite. It was found that when the number of ARB cycles was increased, the uniformity of the Si and SiC_p in the aluminum matrix improved, the Si particles became finer and more spheroidal, the free zones of Si and SiC particles disappeared, the porosity of composite decreased, the bonding quality between SiC_p and matrix improved, and therefore mechanical properties of the composites were improved. The microstructure of the manufactured Al356/SiC_p composite after six ARB cycles indicated a completely modified structure so that its tensile strength and elongation values reached 318 MPa and 5.9%, which were 3.1 and 3.7 times greater than those of the as-cast composite, respectively.     

SiCp/Al复合材料与Fe36Ni合金超声波钎焊

利用超声波钎焊方法使用ZnAlSi钎料实现了Fe36Ni合金与45%SiC_p/2024Al和55%SiC_p/A356两种复合材料的连接,并得到由SiC颗粒增强的复合焊缝.通过扫描电镜、能谱等方法对焊缝的微观结构以及断口形貌进行了观察,对接头的压剪强度进行了测试,分析了Fe36Ni与两种复合材料钎焊接头微观组织和接头强度的差异.结果表明,在Fe36Ni与两种复合材料的钎缝中,钎料与两侧母材界面均形成良好的冶金结合,SiC颗粒均匀分布于焊缝中.Fe36Ni与45%SiC_p/2024Al的接头抗剪强度为110~145 MPa,Fe36Ni与55%SiC_p/A356的接头抗剪强度为75~85 MPa.Fe36Ni与45%SiC_p/2024Al的接头断裂位置为钎缝中,而Fe36Ni与55%SiC_p/A356的接头断裂位置位于Fe36Ni与钎料的界面上.     

SiCp/Al复合材料电子束焊接接头组织及性能

对SiCp/Al复合材料自身进行电子束焊接,研究了其接头成形、焊缝组织、热影响区组织及接头力学性能.结果表明,SiCp/Al复合材料自身直接电子束焊接时,接头的主要缺陷是焊缝成形差、易形成两侧堆积颗粒物的凹槽;焊缝组织中存在界面反应产生的灰白色初生硅、深灰色针状相Al4C3以及Al-Si共晶中的浅灰色针状共晶硅,形成脆性区,拉伸断裂位置便在此处,断裂为脆性断裂.熔合区附近硬度较高,与焊缝区组织及硬度差异较大.接头的最高强度为73 MPa,仅占母材平均抗拉强度的41％.     

Nano-SiCP particles distribution and mechanical properties of Al-matrix composites prepared by stir casting and ultrasonic treatment

Nano-ceramic particles are generally difficult to add into molten metal because of poor wettability. Nano-SiC_Particles reinforced A356 aluminum alloy composites were prepared by a new complex process, i.e., a molten-metal process combined with high energy ball milling and ultrasonic vibration methods. The nano particles were β-SiC_P with an average diameter of 40 nm, and pre-oxidized at about 850 °C to form an oxide layer with a thickness of approximately 3 nm. The mm-sized composite granules containing nano-SiC_P were fi rstly produced by milling the mixture of oxidized nano-SiC_P and pure Al powders, and then were remelted in the matrix-metal melt with mechanical stirring and treated by ultrasonic vibration to prepare the composite. SEM analysis results show that the nano-SiC_P articles are distributed uniformly in the matrix and no serious agglomeration is observed. The tensile strength and elongation of the composite with 2 wt.% nano-SiC_P in as-cast state are 226 MPa and 5.5%, improved by 20% and 44%, respectively, compared with the A356 alloy.     

热处理对SiCp/6061Al基复合材料等离子弧焊接头性能的影响

热处理对SiCp/6061Al基复合材料等离子弧原位焊接接头组织与性能的影响较为明显,固溶处理 时效与退火相比,前者对接头的改善作用更佳.经500 ℃固溶处理2 h 12 h时效热处理后,接头组织得到良好的改善,细长的Al3Ti相变为短小棒状,消除了晶间偏析,组织更加均匀;热影响区组织中晶粒均得到比较明显的细化,比较接近母材晶粒的大小,焊接接头强度较未热处理时有了较大提高,达到245 MPa.     

Microstructure and Mechanical Properties of Al356/SiCp Cast Composites Fabricated by a Novel Technique

In this study, SiC_p containing composite powders were used as the reinforcement carrier media for manufacturing cast Al356/5 vol.% SiC_p composites. Untreated SiC_p, milled particulate Al-SiC_p composite powder, and milled particulate Al-SiC_p-Mg composite powder were injected into Al356 melt. The resultant composite slurries were then cast from either a fully liquid state (stir casting) or semisolid state (compocasting). The results revealed that by injection of composite powders, the uniformity of the SiC_p in the Al356 matrix was greatly improved, the particle-free zones in the matrix were disappeared, the SiC particles became smaller, the porosity was decreased, and the matrix microstructure became finer. Compocasting changed the matrix dendritic microstructure to a finer non-dendritic one and also slightly improved the distribution of the SiC_p. Simultaneous utilization of Al-SiC_p-Mg composite powder and compocasting method increased the macro- and micro-hardness, impact energy, bending strength, and bending strain of Al356/SiC_p composite by 35, 63, 20, 20, and 40%, respectively, as compared with those of the composite fabricated by injection of untreated SiC_p and stir casting process.     

Microstructures and mechanical properties of Al 2519 matrix composites reinforced with Ti-coated SiC particles

Ti-coated SiC_p particles were developed by vacuum evaporation with Ti to improve the interfacial bonding of SiC_p/Al composites. Ti-coated SiC particles and uncoated SiC particles reinforced Al 2519 matrix composites were prepared by hot pressing, hot extrusion and heat treatment. The influence of Ti coating on microstructure and mechanical properties of the composites was analyzed by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The results show that the densely deposited Ti coating reacts with SiC particles to form TiC and Ti₅Si₃ phases at the interface. Ti-coated SiC particle reinforced composite exhibits uniformity and compactness compared to the composite reinforced with uncoated SiC particles. The microstructure, relative density and mechanical properties of the composite are significantly improved. When the volume fraction is 15%, the hardness, fracture strain and tensile strength of the SiC_p reinforced Al 2519 composite after Ti plating are optimized, which are HB 138.5, 4.02% and 455 MPa, respectively.     

YbB6 对Ti-6Al-4V钛合金组织和性能的影响

采用放电等离子烧结（SPS）制备了含YbB₆的Ti-6Al-4V钛合金,并研究了YbB₆对Ti-6Al-4V钛合金显微组织和力学性能的影响。结果表明,随着YbB₆含量的增加,复合材料的显微组织发生转变,晶粒明显细化,原位反应生成的TiB晶须和Yb₂O₃颗粒有利于复合材料力学性能的提高。此外,当添加0.6%（质量分数）YbB₆后,烧结样品的相对密度、显微硬度、屈服强度、极限拉伸强度和延伸率分别为99.43%、4030 MPa、903 MPa、1148 MPa和3.3%。与Ti-6Al-4V试样相比,其数值分别提高了0.37%、13.8%、38.07%和17.14%。强化机制主要是组织转变、晶粒细化和弥散强化。随着YbB₆含量的增加,断裂方式主要为韧性断裂和脆性断裂。     

Microstructural evolution and its effects on mechanical properties of spray deposited SiCp/8009Al composites during secondary processing

15% (volume fraction) SiC_p/8009Al metal matrix composites(MMCs) prepared by spray co-deposition were hot-extruded and rolled to investigate the effects of porosity and local SiC_p clusters on mechanical properties. The microstructures were examined by using optical microscopy(OM), scanning electron microscopy(SEM), X-ray diffractometry(XRD) and transmission electron microscopy(TEM). The mechanical properties were measured by tensile testing. The experimental results show that lamellar structure is composed of pores and SiC_p clusters and can be improved by secondary processing, enhancing mechanical properties. The main strengthening mechanism and fracture behavior of MMCs were discussed too.     

Production and mechanical properties of nano SiC particle reinforced Ti–6Al–4V matrix composite

Different mass fractions (0, 5%, 10%, and 15%) of the synthesized nano SiC particles reinforced Ti–6Al–4V (Ti64) alloy metal matrix composites (MMCs) were successfully fabricated by the powder metallurgy method. The effects of addition of SiC particle on the mechanical properties of the composites such as hardness and compressive strength were investigated. The optimum density (93.33%) was obtained at the compaction pressure of 6.035 MPa. Scanning electron microscopic (SEM) observations of the microstructures revealed that the wettability and the bonding force were improved in Ti64 alloy/5% nano SiC_p composites. The effect of nano SiC_p content in Ti64 alloy/SiC_p matrix composite on phase formation was investigated by X-ray diffraction. The correlation between mechanical parameter and phase formation was analyzed. The new phase of brittle interfaced reaction formed in the 10% and 15% SiC_p composite specimens and resulted in no beneficial effect on the strength and hardness. The compressive strength and hardness of Ti64 alloy/5% nano SiC_p MMCs showed higher values. Hence, 5% SiC_p can be considered to be the optimal replacement content for the composite.     

Fabrication and characterization of Al356/SiCp semisolid composites by injecting SiCp containing composite powders

Al356/5 vol.% SiC_p cast composites were fabricated by the injection of reinforcement particles into the melt in three different forms, i.e. as untreated SiC_p, milled particulate Al-SiC_p composite powder, and milled Al-SiC_p-Mg composite powder. The resultant composite slurries were then cast in the semisolid temperature range of the alloy, upon which the effects of the type of injected powder on the distribution and incorporation of the reinforcement particles, along with the hardness of the cast composites, were investigated. Injection of milled composite powders resulted in considerable improvement in SiC_p wetting as well as the incorporation and distribution of SiC_p in the Al356 matrix alloy. Al356/5 vol.% SiC_p composite with well dispersed reinforcement particles of less than 3 μm average diameter was successfully produced by injecting Al-SiC_p-Mg composite powder into the melt. The best microstructural characteristics in terms of the reinforcement incorporation and distribution, and the highest hardness value of the cast composites, were achieved when magnesium was added through the injected composite powder and not directly into the melt.     

真空压力浸渗制备SiCp/AZ91复合材料的显微组织、力学性能和磨损行为

采用真空压力浸透法制备SiC_p/AZ91复合材料,研究其显微组织、力学性能和耐磨性。结果表明,SiC颗粒均匀分布于金属基体中,并与基体界面结合良好。Mg₁₇Al₁₂相在SiC颗粒附近优先析出,SiC与AZ91基体的热膨胀系数失配导致高密度位错的产生,加速基体的时效析出。与AZ91合金相比,SiC颗粒的加入提高了复合材料的硬度和抗压强度,这主要是由于载荷传递强化和晶粒细化强化机制。此外,由于SiC具有优异的耐磨性,在磨损过程中形成稳定的支撑面保护基体。     

Effect of Sb on microstructure and mechanical properties of Mg2Si/Al-Si composites

The effect of Sb on the microstructure and mechanical properties of Mg2Si/Al-Si composites was investigated.The results show that Sb can improve the microstructure and mechanical properties of Mg2Si/Al-Si composites.When the content of Sb is 0.4%,the morphology of primary Mg2Si changes from dendrites to fine particles,the average size of Mg2Si particles is refined from 52 to 25μm,and the ultimate tensile strength and elongation of the composites increase from 102.1 MPa and 0.26% to 138.6 MPa and 0.36%,respectively.The strengthening mechanism can be attributed to the fine-grain strengthening.However,excessive Sb is disadvantageous to the modification of the composites.     

SiC_p/2024与2219铝合金电子束焊接

分别采用电子束对中焊、偏束焊技术,研究了Si C颗粒增强铝基复合材料Si Cp/2024与2219铝合金的接头组织及力学性能.结果表明,对中焊时接头易出现Si C增强相的偏聚,同时发生严重的界面反应,生成大量脆性相Al4C3,接头抗拉强度最高为104 MPa.采用偏束焊工艺可以很好地抑制界面反应,通常只在焊缝上部与Si Cp/Al热影响区上部生成少量脆性相Al4C3,接头抗拉强度最高可达131 MPa.试件均断裂在母材界面反应层上,且为明显的脆性断裂.不同工艺下接头横截面硬度分布存在突变区,该区域在Si Cp/2024熔合区附近,该处脆性相Al4C3的生成导致硬度升高.     

电弧超声对SiC_p/AlMMCs焊缝组织与性能的影响

以Ti合金作为填加材料,以氮氩混合气作为离子气,对SiCp/6061Al基复合材料进行电弧超声等离子弧原位合金化焊接,研究了电弧超声对等离子弧焊接头组织和性能的影响.结果表明,在不加超声时,焊缝中新生AlN相呈细长条状,Al3Ti相粗大,TiC,TiN等新生增强颗粒分布不均匀;在加入超声后,焊缝组织细密,TiC,TiN,AlN等增强相呈细小颗粒状存在,数量增加,且分布均匀,Al3Ti相尺寸减小,数量减少,从而有效改善了焊接接头的组织和性能,使焊接接头抗拉强度最大值达到225MPa,比不加超声时提高了约7%.     

Fabrication and characterization of cast magnesium matrix composites by vacuum stir casting process

A vacuum stir casting process is developed to produce SiC_p reinforced cast magnesium matrix composites. This process can eliminate the entrapment of external gas onto melt and oxidation of magnesium during stirring synthesis. Two composites with Mg-Al9Zn and Mg-Zn5Zr alloys as matrices and 15 vol.% SiC particles as reinforcement are obtained. The microstructure and mechanical properties of the composites and the unreinforced alloys in as-cast and heat treatment conditions are analyzed and evaluated. In 15 vol.% SiC_p reinforced Mg-Al9Zn alloy-based composite (Mg-Al9Zn/15SiC_p), SiC particles distribute homogenously in the matrix and are well bonded with magnesium. In 15 vol.% SiC_p reinforced Mg-Zn5Zr alloy-based composite (Mg-Zn5Zr/15SiC_p), some agglomerations of SiC particles can be seen in the microstructure. In the same stirring process conditions, SiC reinforcement is more easily wetted by magnesium in the Mg-Al9Zn melt than in the Mg-Zn5Zr melt. The significant improvement in yield strength and elastic modulus for two composites has been achieved, especially for the Mg-Al9Zn/15SiC_p composite in which yield strength and elastic modulus increase 112 and 33%, respectively, over the unreinforced alloy, and increase 24 and 21%, respectively, for the Mg-Zn5Zr/15SiC_p composite. The strain-hardening behaviors of the two composites and their matrix alloys were analyzed based on the microstructure characteristics of the materials.     

Multi-objective optimization of friction stir welding parameters using desirability approach to join Al/SiCp metal matrix composites

Silicon carbide particulate (SiC_p) reinforced cast aluminium (Al) based metal matrix composites (MMCs) have gained wide acceptance in the fabrication of light weight structures requiring high specific strength, high temperature capability and good wear resistance. Friction stir welding (FSW) process parameters play major role in deciding the performance of welded joints. The ultimate tensile strength, notch tensile strength and weld nugget hardness of friction stir butt welded joints of cast Al/SiC_p MMCs (AA6061 with 20% (volume fraction) of SiC_p) were investigated. The relationships between the FSW process parameters (rotational speed, welding speed and axial force) and the responses (ultimate tensile strength, notch tensile strength and weld nugget hardness) were established. The optimal welding parameters to maximize the mechanical properties were identified by using desirability approach. From this investigation, it is found that the joints fabricated with the tool rotational speed of 1370 r/min, welding speed of 88.9 mm/min, and axial force of 9.6 kN yield the maximum ultimate tensile strength, notch tensile strength and hardness of 265 MPa, 201 MPa and HV114, respectively.     

Ti-Al-Si-Mg对SiCp/Al基复合材料等离子弧原位焊接焊缝组织和性能的影响

以填充自制药芯铝焊丝的形式向熔池内部直接添加Ti,Al,Si,Mg等金属元素,用氩氮混合等离子气体对SiCp/Al基复合材料进行等离子弧原位焊接.分析了Ti-Al-Si-Mg以及它们的氧化物对焊缝组织和性能的影响.结果表明,以Ti-Al-Si-Mg作为原位反应填充材料,可以有效抑制针状脆生相Al4C3的生成,改善熔池流...     

La2O3对MGH956合金TIG焊焊缝组织和性能的影响

为了研究La₂O₃对焊缝组织和性能的影响,分别以未填加、填加2%和4%La₂O₃的填充材料对MGH956合金进行TIG焊接,应用光学显微镜、扫描电镜和透射电镜对焊缝的微观组织和拉伸断口进行观察,同时测试焊缝的抗拉强度.结果表明,适当提高La₂O₃含量,可以使焊缝晶粒得到细化,填加2%La₂O₃的焊缝晶粒最细小均匀,焊缝中的颗粒相增多且分布均匀,强化机制是由细晶强化和Orowan强化共同作用,但当La₂O₃加入量达到4%时,发现颗粒相有团聚现象,强化主要由位错塞积引起.填加2%La₂O₃的焊缝抗拉强度最大,为628 MPa,拉伸断口为韧-脆混合断裂.     

AlSi7Mg合金半固态压铸件热处理强化机理研究

对AlSi7Mg合金(A356)半固态压铸件和液态压铸件进行了不同工艺的固溶与时效热处理，分析了其显微组织与疏松度，测定了硬度、拉伸强度及延伸率等力学性能。实验得出，铝合金半固态压铸件原始态的力学性能优于液态压铸件，并且半固态压铸件时效强化效果尤其明显，拉伸强度可达330MPa以上，延伸率10％以上。这主要是由于半固态压铸件比液压件具有更加致密，且为球状的非树枝晶组织。铝合金半固态压铸件时效强化，机理主要归于弥散析出Mg2Si强化相。