共查询到20条相似文献,搜索用时 297 毫秒
1.
特高压输电线路大跨越档距大、挂点高,导线微风振动水平显著,防振设计难度大。目前,大跨越导线的防振方案设计基本依赖于实验室微风振动模拟试验来完成,该试验流程复杂,且必须安装真型导线及金具,因此试验周期有时长达数月。基于有限元方法和能量平衡原理,开发了特高压输电线路大跨越防振设计系统,具备分裂导线微风振动模态分析、谱分析和瞬态分析功能,能够针对初步设计方案计算出分裂导线各关键点处的动弯应变值,并对多个方案进行对比分析,推选出较优的防振方案进行试验验证,从而减少特高压输电线路大跨越防振试验次数,提高防振方案设计效率,更好地满足特高压工程进度要求。 相似文献
2.
铝合金导线具有多方面的优点,已在世界许多国家的输电线路上广泛应用,而我国在500 kV 线路上尚未采用。实践证明,铝合金导线适宜在500 kV 线路上推广应用。建议在500 kV 线路上采用铝合金绞线(AAAC) 时,平均运行应力( EDS) 上限值取25 %UTS ,最大设计张力取40 %UTS ,并根据AAAC 的特点改进防振措施。 相似文献
3.
500KV线路大跨越分裂导线防振试验研究 总被引:2,自引:0,他引:2
微风振动引起的导线疲劳断线严重威胁到输电线路的安全运行。随着500KV超高压线路的发展,对分裂导线的大踞度开展防振研究已变得十分重要。本文总结了近十几年来我国大跨越防振试验研究的技术成果,结合500KV大跨越实际工程,借鉴国际上先进经验,系统地论述了大踞越分裂导线防振试验研究技术的开发,包括导线振动测试技术、试验程序、线路振动强度的计算方法及防振方案优选等一整套技术。这一技术不仅适用于四分裂导线防 相似文献
4.
5.
6.
7.
8.
自1966年以来,弹簧防振装置已在全国24条35~110kV线路上应用,运行结果如下:1)所有装有弹簧装置的线路的线夹内,没有发现导线断股,说明弹簧防振装置已起到消振和保护导线的作用,2)现场观察发现弹簧防振线路的振动较防振锤防振线路的振动严重。导线垂直振幅很大,横担吊杆振动噪声也较大,说明弹簧防振不是压迫振动,而是传递振动,改善导线的受力情况带来了横担、吊杆、导线与线夹联接处的噪声。现对弹簧防振装置的性能作一些 相似文献
9.
10.
500kV江阴长江大跨越线路导、地线采用了阻尼线加防振锤的联合防振方案,导线还充分利用阻尼式间隔棒来消振,OPGW地线设计时采用双花边阻尼线防振方案。后发现OPGW高频端固定阻尼线的线夹盖板脱落并磨损护线条,后来补充的减震措施(在直线档高频段加装了一截阻尼线)效果也不理想。针对此缺陷情况采取的措施包括:及时消缺及加强巡视检测;采取固定阻尼线线夹螺栓防松措施;单根较长阻尼线防振效果比采用双根较短阻尼线要好,可以参考地线对OPGW地线的防振方案进行技改;安装现场测振系统,建立大跨越测振档案,调整振动系统,保证大跨越防振系统安全稳定运行。 相似文献
11.
照明配电系统中,气体放电灯产生的3次谐波电流对中性线导体电流影响很大。分析了3次谐波电流在三相四线制线路中的影响,导体截面选择的依据和相关计算。实例计算分析结果表明,在照明供电线路中,3次谐波电流对导线截面的选择起决定作用,因此在照明线路的设计中应考虑谐波的影响,避免供电事故的发生。 相似文献
12.
13.
This paper proposes an approximate impedance formula of a conductor with an arbitrary cross section, and also a method of approximating the conductor by an equivalent circular conductor. Thus, a multiconductor system consisting of arbitrary cross section conductors is represented by circular cross section conductors, the impedance of admittance of which are evaluated by the existing impedance and admittance formulas. The calculated results by the proposed method agree satisfactorily with measured results and numerical results by a finite-element method which is, at present, the only way of calculating such impedance, but requires a large computation time and large memory. The proposed method might be very useful in evaluating the impedance and admittance of a multiconductor system consisting of arbitrary cross section conductors. 相似文献
14.
In this paper, the temperature distribution within an ACSR conductor was precisely measured and examined, conducted as part of a series of studies on large currents in transmission lines. The study results may be summarized as follows: (1) The temperature difference within the conductor cross section increases as the square of the current; however, even at a current equal to 50% more than the allowable current, the maximum temperature difference within the aluminum components is from 5 °C (ACSR 410 mm2) to 6 °C (ACSR 810 mm2). (2) The results of measurements of the conductance between outer‐layer and inner‐layer aluminum strands in the conductor, and analysis of the current distribution in the inner and outer layers, indicated that even if the conductance were to drop sharply to 10,000 S/m, any inhomogeneity or concentration in the current distribution at a conductor connection joint has disappeared by 1.5 m or so from the tip of the joint. (3) According to measurements of the conductor temperature near a joint, the electrical resistance of the joint is lower than that of the same length conductor, so that the conductor temperature falls for 0.5 m or so from the tip of the joint. (4) Based on the above findings, the temperature distribution within an ACSR conductor accompanying the passage of large currents can be regarded as nearly uniform both across the conductor cross section, and in the conductor length direction. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 140(4): 38–45, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10041 相似文献
15.
规划中的1 000 kV苏通长江大跨越工程跨距大,耐张段长,通航要求高,选择合理的导线是工程可行的关键.从导线材料、导线结构、制造条件方面选取常规的6×AACSR/EST-500/230与8×AACSR/EST-400/180特强钢芯高强铝合金导线方案,对2种方案进行输送容量、电磁环境、机械特性、经济性等方面的比较,计算结果表明,具有较好机械性能的6分裂导线方案优于8分裂导线方案.对AACSR/EST-500/230导线从材料和结构2个方面进行优化,提高钢芯的抗拉强度及适当降低铝钢截面比,导线优化后使跨越塔高度大为降低,减少工程投资.推荐1 000 kV苏通长江大跨越工程导线采用6×AACSR/UST-500/280超高强度钢芯高强度铝合金绞线. 相似文献
16.
提出一种大截面扩径导线设计新思路,铝股外层采用圆线密排,支撑层采用型线疏绞。通过电磁环境控制要求和输送容量确定大截面扩径导线结构设计的边界条件,外径为42.88 mm,导电截面为780 mm2。对JLXK/G2A-780(1000)/80-42.88扩径导线进行结构和参数设计,技术经济分析表明其初期投资较8×1 000 mm2常规导线方案低。全寿命周期内,在电价较低、损耗小时数较小时,扩径导线方案经济性优于8×JL/G2A-1000/80导线方案。借助扩径导线截面稳定性计算机仿真程序进行计算分析,得到其临界跳股张力为25%额定拉断力(rated tensile strength,RTS)。将试制样品通过试验设备进行结构稳定性验证,得到其临界跳股张力为25%RTS,与模拟结果一致。综上所述,大截面扩径导线JLXK/G2A-780(1000)/80-42.88,截面稳定性好,适用于电磁环境要求高、利用小时数低的工程。 相似文献
17.
随着输电线路电压等级的提高,大截面导线、分裂导线的应用越来越多,风噪声和电晕噪声的问题日趋严重。导线风噪声是风吹过导线后,由导线表面的流体剥离所引起的压力变化所产生。在导线表面采取缠绕扰流线措施或直接使用低噪声导线,能够降低导线风噪声和电晕噪声水平。目前我国尚未开展防导线风噪声的研究。在我国输电线路飞速发展、特别是在特高压输电线路的前期准备工作中,应及时开展防导线风噪声的试验研究。 相似文献
18.
阐述了单芯中压交联电缆金属屏蔽层使用中存在的问题 ,提出了一些防范措施 ,对选择金属屏蔽层截面积也作了实例计算 相似文献
19.