Temperature dependence of dynamics of solutions of triblock copolymer in a selective solvent

The temperature dependence of dynamic properties of solutions of a triblock copolymer with polystyrene outer blocks and a middle block of fully hydrogenated polybutadiene (M_w=7.0×10⁴ gmol⁻¹, mass fraction of PS 0.28) was studied in a selective solvent for the middle block, n-heptane. In dilute solutions, a gradual decomposition of the flower-like micelles was observed on heating. A more complex behavior was observed in semidilute solutions of the copolymer where three dynamic processes can be reliably extracted from the correlation functions. The fast mode corresponds to the collective diffusion mode of physically interconnected micelles, the broad middle mode is probably due to the tracer diffusion of polydispersed clusters (animal-like structures) formed by random association of the triblock copolymer and the slow mode is probably related to the diffusion of aggregates of insoluble polystyrene impurities. The crossover from relaxational to diffusive behavior was found for samples with c>5.5% (w/v). The scattered light intensity measurements revealed a phase transition for the solution with the concentration 4% (w/v) at a temperature of 79±2°C, which was related to the phase separation of polystyrene homopolymer present in a small amount in the copolymer used.     

Segregation and conformational transitions in triblock copolymers in dilute solution: 3. Viscometric investigations in solvent mixtures

Viscometric measurements were carried out on a triblock copolymer PMMA/PS/PMMA at two temperatures in two binary solvent mixtures, in order to establish to what extent segregation between the two kinds of blocks is maintained as the composition of the solvent mixture i.e. its preferential affinity to one of the blocks, changes. From the variation of the limiting viscosity number of the polymer versus composition of the solvent mixture, taking into account the corresponding plots for the two homopolymers, it was established: that at relatively low temperature the molecular dimensions of the block copolymer are very close to those calculated neglecting the heterocontact interactions, i.e. assuming segregation, and that at higher temperatures the dimensions observed for the block copolymer are higher than the values calculated by assuming segregation, thus showing that the heterocontacts exert some influence, inducing the chain to expand. A comparison with a PS/PMMA random copolymer of the same composition showed, however, that in the same solvent mixtures the number of heterocontacts was far lower in the case of the block copolymer than in the case of the random copolymer, even at elevated temperatures.     

Temperature and concentration dependence of diffusion coefficient in dilute solutions

Temperature and molecular weight dependence of k_D in D(C) = D(O) [1 + Ck_D], where D(C) is the diffusion coefficient for the density fluctuations in a dilute polymer solution, is investigated by first expressing D(C) as a function of the static structure factor S(q,C) within the framework of the Kirkwood-Riseman theory. The continuous transition of k_D from negative values under theta conditions to positive values in good solvents is calculated using various models for the intermolecular interaction potential and the results are presented graphically as function of a reduced variables $\text{S}\text{?}\text{R}{}_{\mathrm{H}}$ that combines both molecular weight and temperature effects. It is shown that the negative value of k_D at the theta temperature can be explained at least partially, in terms of an increase in the chain dimensions of two overlapping molecules. The concentration dependence of the self-diffusion coefficient is also discussed.     

Temperature influence on the behavior of polysulfone‐b‐poly(alkylene oxide)‐b‐poly(dimethylsiloxane) triblock copolymers in a selective solvent

Triblock copolymers containing polysulfone, poly(alkylene oxide), and poly(dimethylsiloxane) segments were obtained by addition of preformed α,ω‐bis(hydrogensilyl) poly(dimethylsiloxane) oligomers to alyl end‐capped poly(alkylene oxide)‐b‐polysulfone. Viscometric and UV absorption measurements were carried out in dilute 1,2‐dichlorethane solutions, in the temperature range of 20–75°C. The specific interactions exhibited by the block copolymers in a selective solvent are influenced by the copolymer composition and temperature. The results point to a conformational transition phenomenon, located around 55°C, which is attributed to the transition from a segregated to a pseudo‐Gaussian conformation through a compressed‐segregated conformation. POLYM. ENG. SCI., 57:114–118, 2017. © 2016 Society of Plastics Engineers     

Depolarization behaviour of dilute polymer solutions: II. Angular dependence and analyzer absorption

Study of the depolarization behaviour of dilute polymer solutions leads to determination of the Cabannes factor, necessary for correcting the Rayleigh ratio used in light‐scattering calculations for deviations due to anisotropy. We present here a method to determine the Cabannes factor for polymers as a simultaneous function of both scattering angle and molar mass, accomplished by coupling size‐exclusion chromatography with depolarization multi‐angle light scattering (SEC/D‐MALS). The depolarization behaviour of brominated polystyrene (PSBr), previously studied at a right‐angle geometry, is seen to possess a non‐trivial angular dependence in addition to being a function of molar mass. We also demonstrate initial attempts at correcting SEC/D‐MALS results for absorption of light by the Polaroid filters that act as analyzers in the optical train of the system. Copyright © 2003 Society of Chemical Industry     

Sedimentation behaviour in dilute solutions of a polyelectrolyte

Sedimentation velocity studies are reported for dilute aqueous solutions of sodium poly(styrene sulphonate) with various quantities of added NaCl. On increasing the salt concentration the dependence of 1/S on polymer concentration decreases and, up to 0.5 M NaCl, the limiting sedimentation coefficient increases. These changes are related to changes in the effective charge on the polymer, which increases with increasing salt concentration, and in the friction coefficient, which decreases with increasing salt concentration. The effective charge on the polymer should be considered when evaluating the Mandelkern-Flory parameter, $\text{ø}{}^{\mathrm{<mtext>1</mtext><mtext>3</mtext>}}\text{P}{}^{\mathrm{?1}}$.     

Synthesis and self-assembly of polyimide/poly(dimethylsiloxane) brush triblock copolymers

A series of novel brush triblock copolymers containing ‘glassy’ fluorinated polyimide, poly((4,4′-hexafluoroisopropylidene diphthalic anhydride)-co-(2,3,5,6-tetramethyl-1,4-phenylenediamine)) (poly(6FDA-co-TMPD)), and ‘rubbery’ polydimethylsiloxane monomethacrylate (PDMS-MA) were synthesized and characterized. Well-defined difunctional poly(6FDA-co-TMPD) with α,ω-amino end-groups was initially prepared via step-growth polymerization using precise control of the diamine (TMPD) to dianhydride (6FDA) ratio. Subsequent functionalization with 2-bromoisobutyryl bromide afforded a telechelic macroinitiator suitable for atom transfer radical polymerization (ATRP). The macroinitiator and its diamino poly(6FDA-co-TMPD) precursor were characterized via gel permeation chromatography (GPC), ¹H nuclear magnetic resonance (NMR) spectroscopic analysis and matrix assisted laser desorption ionization time-of-flight (MALDI ToF) mass spectroscopy. ATRP of PDMS-MA using the macroinitiator in different molar ratios afforded a series of brush triblock copolymers with high monomer conversions (88–94%) and varying PDMS weight fractions. Self-assembly of the triblock brush copolymers in dimethylformamide (DMF) afforded nanoparticles with hydrodynamic diameters (d_H) ranging from 87 to 109 nm, as determined by dynamic light scattering (DLS) analysis. Cross-linking of the nanoparticles was achieved via hydrogen abstraction through the thermal degradation of benzoyl peroxide. Transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM) revealed that the self-assemblies and their cross-linked derivatives had spherical morphologies.     

Synthesis and bulk properties of poly(tetrahydrofuran)-poly(2-methyl-2-oxazoline) ABA triblock copolymers

A series of linear triblock-copolymers of the ABA type in which the central B-block is poly(tetrahydrofuran) (polyTHF) and the A-segments are poly(2-methyl-2-oxazoline) (polyMeOX) were synthesized by a one-pot sequential monomer addition copolymerization, utilizing the living nature of the cationic ring-opening polymerization of both monomers. Films of the copolymers, casted from chloroform solutions, exhibit excellent mechanical properties in comparison with the homopolymers with comparable molecular weights, which was ascribed to the phase separation occurring between the two copolymer segments. Materials, in which the polyTHF B-segment have a molecular weight 13 000 g/mol or higher and each polyMeOX A-block a molecular weight 1500 g/mol, kept elastomeric properties up to 130 °C notwithstanding the fact that this temperature is considerably higher than the melting point of polyTHF and the glass transition temperature of polyMeOX. It was found that these triblock-copolymer materials show a shape memory effect. These observations are attributed to the high degree of phase separation between the two blocks and the strong polar interactions between the polyMeOX segments. Received: 20 March 1997/Revised: 5 September 1997/Accepted: 8 September 1997     

Temperature/rate dependence of yield and fracture behaviour of phenolphthalein poly(ether ketone)

The rate/temperature dependence of yield stress, tensile modulus and crack opening displacement of phenolphthalein poly(ether ketone) (PEK-C) has been investigated. The rate/temperature dependence of crack opening displacement and the correlation established between stress intensity factor, K_IC, yield stress, and type of crack growth suggest that the extent of crack tip blunting largely governs the relative toughness of PEK-C and induces transitions in the types of crack growth observed. A quantitative expression is then presented which successfully describes the fracture toughness values over a wide range of temperatures and rates.     

Fatigue behaviour of multiblock thermoplastic elastomers. 2. Dynamic creep of poly(aliphatic/aromatic-ester) copolymers

The ‘dynamic creep’ behaviour of poly(aliphatic/aromatic-ester) (PED) multiblock copolymers has been evaluated by the hysteresis measurements method. The effect of the hard/soft segments concentration on the microphase separation in PED copolymers was determined by means of differential scanning calorimetry. The ‘dynamic creep’ of PED copolymers has been compared with poly(ether-ester) and segmented polyurethanes indicating on the good creep behaviour of PEDs compared to those materials. It was found that the hard segment content influences the creep behaviour of PED copolymers at ambient and elevated temperature indicating that stiffer materials are less susceptible to environmental conditions than polymers containing a high amount of the soft phase. PED copolymers compare very well with commercially available poly(ester-ethers) and show much lower creep compared to poly(ether-urethanes).     

Self-assembly of amphiphilic di and triblock copolymers of styrene and quaternized 5-(N,N-diethylamino) isoprene in selective solvents

Self-association of highly asymmetric block copolymers of styrene and quaternized 5-(N,N-diethylamino)isoprene was studied. After quaternization with dimethyl sulfate, the di and triblock copolymers consisted of a long block of polystyrene (PS) with a short poly[5-(N,N,N-diethylmethylammonium)isoprene][methyl sulfate](PAI) block at one or both chain ends, respectively. The aggregates were prepared by first dissolving the copolymers in an organic solvent and then adding water to induce the segregation of the PS chains. Pure DMF, THF or dioxane was used as the organic solvent, as well as DMF/THF mixtures. The critical water content (cwc) and the morphologies were studied as a function of the common solvent, initial copolymer concentration and architecture (di or triblock) by static light scattering and by Transmission Electron Microscopy (TEM), respectively. It was found that both, the cwc and the morphologies of the aggregates are most strongly affected by the nature of the common solvent. Some unexpected behaviors were found for the triblock copolymer. Morphologies of a triblock copolymer in various mixtures of DMF and THF, quenched at determined water contents, were investigated in order to study the degree of morphological control that can be achieved solely as function of the organic solvent composition. Multiple morphologies have been found including equilibrium morphologies and kinetically trapped ones. Finally, the stability of primary micelles prepared in DMF was studied by DLS, upon dilution with DMF and water, and a possible mechanism for the destabilization of the aggregates is proposed.     

Frustrated structures of polycaprolactam and poly(p-benzamide) in their rod-coil-rod triblock copolymers

A series of rod-coil-rod triblock copolymers were synthesized by two-step polycondensation with polycaprolactam (PA6) as the flexible block and poly(p-benzamide) (PBA) as the rod. Proton nuclear magnetic resonance (¹H NMR), UV-vis spectrophotometry and differential scanning calorimetric (DSC) were first performed to determine the fundamental molecular structure and thermal property of each polymer. Through wide angle X-ray scattering (WAXS), and Fourier transformation infrared spectroscopy (FT-IR) measurements, frustrated structures of both components were studied. For PA6, a quasi-γ mesomorphic order was found in the transition-region nearby the PBA domain which is more favored with the increase of the PBA content owing to stretching from the PBA rod block and different cross-section areas of the rod and coil chains. On the other hand, the mesomorphic order of PA6 segments imposes stretching and constraint on the PBA blocks, which leads to a reduction of order of PBA block when the volume fraction of rod reaches approximately 45%. α crystals of PA6 can form only in the triblock copolymer with low volume fraction of PBA, which exhibit the Brill transition feature during the heating process though this transition ends prematurely as the melting of crystals.     

Synthesis of amphiphilic triblock copolymers for the formation of magnesium fluoride (MgF2) nanoparticles

A series of amphiphilic poly(2‐hydroxyethyl methacrylate)‐b‐polydimethylsiloxane‐b‐poly(2‐hydroxyethyl methacrylate) (pHEMA‐b‐PDMS‐b‐pHEMA) (A‐B‐A) triblock copolymers were synthesized from three different carbinol‐terminated polydimethylsiloxanes with varying molecular weight. A carbinol‐terminated polydimethylsiloxane was modified with 2‐bromoisobutyryl bromide to obtain a macroinitiator. The block copolymers were characterized by NMR, GPC, and dynamic light scattering (DLS). Reverse micelles of a copolymer were formed in mixture of benzene/methanol solution which served as nanoreactors for the synthesis of magnesium fluoride (MgF₂) nanoparticles. The MgF₂ was prepared via chemical precipitation using magnesium chloride and potassium fluoride as reactants. The MgF₂‐triblock copolymer composites were synthesized as a function of MgF₂–weight ratio (0.5, 5, and 10 wt%) in copolymer. The MgF₂ colloids were dissolved in three organic solvents: methanol, isopropanol, and tetrahydrofuran. The polymer nanoparticles were characterized by DLS, transmission electron microscopy, thermogravimetric analysis, and X‐ray diffraction (XRD) analysis. The formation of MgF₂ crystals was observed by XRD. Particle size and particle size distribution showed significant changes in different solvents. The thermal stability of MgF₂ colloids increased as the amount of nanoparticle increased in polymeric matrix. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

(Polystyrene-g-polyisoprene)-b-polystyrene comb-coil block copolymer in selective solvent

Comb-coil block copolymers consisting of two components polystyrene (PS) and polyisoprene (PI) were synthesized through combining TEMPO living free radical polymerization (LFRP) and anionic polymerization using “grafting-onto” strategy. Two typical samples with the same backbone but grafted with different numbers and lengths of branches, forming lamellar and cylinder phases, respectively, were investigated. As the selective solvent was added into these block polymers, the micro-structures transformed from disordered or weakly ordered structure into well-organized lamellar structure in the intermediate polymer concentration. The power law behavior of the lamellae space with respect to polymer concentration indicates that the two samples form the well-organized structure through different paths. The sample with longer branch length thus less branch points forms lamellae phase with smaller lamellae space. This difference at lamellae spacing is attributed to the two different ways that the chain assembles.     

Synthesis and characterization of amphiphilic polyisobutylene/poly(ethylene glycol) di- and triblock copolymers

Summary Di- and triblock copolymers of polyisobutylene PIB and poly(ethylene glycol) PEG have been prepared and characterized. The syntheses involved the capping with tolylene 2,4-diisocyanate TDI various molecular weight -phenyl--(p-phenol) polyisobutylenes C₆H₅-PIB-C₆H₄OH and ,-di-(p-phenol)polyisobutylenes HOC₆H₄-PIB-C₆H₄OH, or commercially available mono- and di-hydroxyl-terminated PEGs. In this manner a series of PIB-b-PEG diblock copolymers, and PEG-b-PIB-b-PEG and PIB-b-PEG-b-PIB triblock copolymers have been obtained. The complete removal of the prepolymers from these amphiphilic sequential copolymers by conventional solvent extraction techniques could not be achieved because of the very high emulsifying action of the latters. In contrast, satisfactory separation was obtained by column chromatography using mixed (polar/nonpolar) eluents. The blocking efficiencies and composition of the block copolymers have been determined.Part XL V of the Series on New Telechelic Polymers and Sequential Copolymers by Polyfunctional Initiator-Transfer Agents (Inifers).     

Characterization of N,N-dimethylacrylamide/2-methoxyethylacrylate copolymers and phase behaviour of their thermotropic aqueous solutions

Dimethylacrylamide (DMA) has been copolymerized with 2-methoxyethylacrylate (MOEA) and solutions of the products were analysed by FTIR to yield derived reactivity ratios r_DMA = 1.11 ± 0.13 and r_MOEA = 0.63 + 0.10. The measured glass transition temperatures T_g of PDMA and PMOEA were 395 K, and 242 K, respectively. These and the values of T_g for the copolymers accorded well with the Fox relationship. Cloud point curves for copolymers in water were established over a wide range of concentration, solubility decreasing with increase in temperature. For these reversibly thermotropic solutions, the lower critical solution temperature (LCST) increased from 9°C to 80°C with decrease in content of MOEA in the copolymer from 91.1 mol% to 38.6 mol%.     

Phase behaviour in poly(ethylene oxide-b-t-butyl methacrylate) block copolymers

The lamellar thickness of the poly(ethylene oxide)-poly(t-butyl methacrylate) (PEO-PTBMA) diblock copolymer system, obtained by differential scanning calorimetry and small angle X-ray scattering investigations, is correlated with the degree of polymerization of the amorphous (PTBMA) and crystallizable (PEO) sequences. The non-equilibrium exponents obtained immediately after bulk crystallization are different to those from extrapolated equilibrium results. Within the experimental standard deviations, the theoretical predictions of DiMarzio et al. and of Whitmore and Noolandi could be confirmed. The molecular weights of PEO and PTBMA ranged from 250 to 21000 g mol⁻¹ and from 1500 to 17000 g mol⁻¹, respectively. Both the equilibrium lamellar thickness l and the PEO domain size d_PEO increase with increasing PEO and decreasing PTBMA degrees of polymerization Z according to d_PEO l Z^0.97±0.08_EOZ^{−(0.53±0.19)}_TBMA.     

The behaviour of poly(2-ethylhexyl acrylate) in dilute solution: viscosity measurements

Summary Linear macromolecules of the poly(2-ethylhexyl acrylate) were prepared by solution polymerization in toluene at 12 °C, using azobisisobutyronitrile as initiator. The polymer was fractionated and the fractions characterized by the methods of light scattering, osmometry and viscometry. Mark-Houwink-Sakurada relations at 25°C in solvents of different thermodynamical quality have been determined.     

Poly[(styrene-co-p-methylstyrene)-b-isobutylene-b-(styrene-co-p-methylstyrene)] triblock copolymers. 1. Synthesis and characterization

The synthesis of poly(isobutylene) (PIB)-based triblock copolymers having copolymer end blocks containing styrene and p-methylstyrene (pMSt) repeat units was investigated in an attempt to minimize chain-coupling reactions that occur at the 4-position on styrene repeat units during end block polymerization. Model end block copolymerizations using varying feed ratios of styrene and pMSt were conducted, and it was determined by ¹H NMR analysis that the addition of pMSt to the living chain end was favored slightly at low conversion. However, DSC revealed a single T_g that increased with increasing pMSt content verifying the absence of blockiness in the microstructure. Poly[(styrene-co-pMSt)-b-isobutylene-b-(styrene-co-pMSt)] triblock copolymers were synthesized using varying feed ratios of styrene and pMSt. The rate of end block propagation increased with increasing pMSt in the feed, and the end block copolymerizations initiated by PIB displayed longer reaction times and more curvature in their first order plots than did the model end block copolymerizations initiated by TMPCl. This effect was attributed to lower ionization equilibrium constant and higher degree of termination caused by the more non-polar local reaction medium provided by the PIB center blocks in block copolymerization. GPC analysis of the final BCPs revealed a decrease in a high molecular weight peak representing the chain-coupled product as the concentration of pMSt in the feed was increased.