Performance of Diagnostic Neutral Beam for the HT-7 Tokamak

Diagnostic neutral beam (DNB), combined with spectral diagnostics, is employed to measure the ion temperature in HT-7. The factors affecting the extracted beam are studied in the experiment for the high performance diagnostic neutral beam. A 6.5 A extracted hydrogen current at 43 keV of 100 ms was obtained after optimization. The extracted beam has a proton ratio as high as 40%, and can penetrate into the core plasma after neutralization to measure the ion temperature effectively.     

NBI双潘宁离子源参数的静电探针测量

介绍了静电探针在22cm双潘宁离子源中心等离子体参数测量中的应用.测出了探针的伏安特性曲线,由该曲线求出在弧流为200 A时,电子温度约为6.0 eV,密度约为2×1012 cm-3,这对于调整放电控制条件,获得高效率大功率的离子源有重要的参考价值,并且对于今后实现强而且均匀的中性束束流的引出也有着重要意义.     

HT-7托卡马克实验装置上基于PLC控制的中性束诊断电源系统

文章介绍HT-7托卡马克实验装置上的中性束诊断电源系统的组成、结构，以及基于S7-300PLC的逻辑控制系统。实验表明，该系统操作简单，性能稳定可靠。     

Ignition Approach by Neutral Beam Injection Heating in Impurity Contaminated Tokamak Reactors

Available heating power by neutral beam injection in a tokamak reactor is evaluated semi-empirically. Using this estimated value, device and plasma parameters to ignite the plasma in impurity contaminated tokamak reactors are investigated. By lowering the plasma density and concurrently by enlarging the plasma minor radius or aspect ratio, the difficulty of NBI heating can be avoided, and the ignition is almost always possible both for trapped ion mode and Alcator scaling laws.     

Control System of Neutral Beam Injection on HT-7

Neutral Beam Injection control system (NBICS) is constructed to measure the plasma current, Magnet current, vacuum pressure, cryopump temperature, control water cooling, filament voltage, and power supply， etc. The NBICS, consisting mainly of a Programmable Logic Controller (PLC) subsystem, data acquisition and processing subsystem and cryopump and vacuum pressure monitoring subsystem, has successfully been used on a NBI device. In this article, the design of NBICS on HT-7 is discussed and each subsystem is described in particular.In addition, some experimental results are reported which are very important data for further research related to the HT-7 tokamak.     

Analysis on Pressure Distribution in HT-7 Neutral BeamInjection System

Neutral Beam Injection (NBI) is an effective way to improve the efficiency of tokamak heating system. This article primarily introduces a work on the pressure distribution inside the tank of NBI heating system, especially inside the neutralizer, which is got by selecting a proper mathematical model and constructing a series of rational calculating formulas on pressure distribution. Furthermore, we simulate the pressure distribution by the Monte Carlo method. Comparing the result of simulation with that of theoretical calculation, we find that both the results are very close each other, showing their mutual validity.     

Discharge Characteristics of Large-Area High-Power RF Ion Source for Positive and Negative Neutral Beam Injectors

A large-area high-power radio-frequency(RF) driven ion source was developed for positive and negative neutral beam injectors at the Korea Atomic Energy Research Institute(KAERI). The RF ion source consists of a driver region, including a helical antenna and a discharge chamber, and an expansion region. RF power can be transferred at up to 10 kW with a fixed frequency of 2 MHz through an optimized RF matching system. An actively water-cooled Faraday shield is located inside the driver region of the ion source for the stable and steady-state operations of high-power RF discharge. Plasma ignition of the ion source is initiated by the injection of argongas without a starter-filament heating, and the argon-gas is then slowly exchanged by the injection of hydrogen-gas to produce pure hydrogen plasmas. The uniformities of the plasma parameter,such as a plasma density and an electron temperature, are measured at the lowest area of the driver region using two RF-compensated electrostatic probes along the direction of the shortand long-dimensions of the driver region. The plasma parameters will be compared with those obtained at the lowest area of the expansion bucket to analyze the plasma expansion properties from the driver region to the expansion region.     

The Spectroscopic Systems for the Study of Light Impurity Particle Transport in the HT-7 Tokamak

Three spectroscopic systems have been developed for the study of light impurity particle transport in the HT-7 tokamak. A visible multi-channel spectroscopic system （VIS） is used to obtain the brightness distribution of the line emission from ionized light impurities. The profile of Zeff（r） has been obtained from the visible multi-channel bremsstrahlung measurement （VB）. The system with a rotating hexahedral mirror for space-time resolved spectroscopy measurement from ultraviolet to visible （UV） can provide the brightness distribution of two different emission lines of the light impurities simultaneously. The emissivities by these multi-channel measurements can be obtained by Abel inversion. The measurement was performed in typical OH discharges in the HT-7 tokamak. The carbon particle transport was analyzed. The feasibility of these diagnostic systems for the impurity particle transport study is clearly demonstrated.     

The Beam Profile Calculation for Diagnostic Neutral Beam on HT-7 Tokamak

A new calculation method is introduced for convergence beam intensity. The program based on this method is prepared for beam intensity distribution and beam power calculation. Taking the HT-7 DNB as a reference, the beam profile calculated by program is similar with that of Gaussian fit of experimental data.     

Design of the Prototype Negative Ion Source for Neutral Beam Injector at ASIPP

In order to support the design,manufacture and commissioning of the negativeion-based neutral beam injection(NBI) system for the Chinese Fusion Engineering Test Reactor(CFETR),the Hefei utility negative ion test equipment with RF source(HUNTER) was proposed at ASIPP.A prototype negative ion source will be developed at first.The main bodies of plasma source and accelerator of the prototype negative ion source are similar to that of the ion source for EAST-NBI.But instead of the filament-arc driver,an RF driver is adopted for the prototype negative ion source to fulfill the requirement of long pulse operation.A cesium seeding system and a magnetic filter are added for enhancing the negative ion density near the plasma grid and minimizing co-extracted electrons.Besides,an ITER-like extraction system is applied inside the accelerator,where the negative ion beam is extracted and accelerated up to 50 kV.     

Radiation Losses in Ohmically Heated Plasma in the HT-7 Tokamak

Total radiation losses in ohmically heated plasma have been investigated in the HT-7 tokamak after different wall conditionings. Discharges after siliconization and boronization have been studied by using bolomitric measurements. Not only low-Z impurities but also high-Z impurities are reduced obviously after wall conditioning. The fraction of the total radiation loss to the ohmic input increases with increasing line-averaged central electron density. But it decreases with increasing the plasma current IP after wall conditionings. It is slightly lower for a boronized wall than that for a siliconized wall.     

Investigation of Ion Temperature Characteristics in the HT-7 Tokamak

Characteristics of ion temperature measured with charge-exchange recombination spectroscopy （CXRS） were studied in Ohmic, lower-hybrid-wave （LHW） driven and ion...     

Logical and Timing Control for Diagnostic Neutral Beam Injection on HT-7

The timing and master control logic （MCL） units are the most important function units of the diagnostic neutral beam （DNB） power supply control system. The units control the operation of nine power supply subsystems of the DNB system, and provide protection for the DNB system from faults such as beam source arc down. Based on the characteristics of the DNB power supply system, the timing and MCL units have been designed, fabricated and tested. Experiments prove that the timing unit is convenient, flexible and reliable, and the MCL is functional.     

Performance of a New Ion Source for KSTAR Tokamak Plasma Heating

In the experimental campaign of 2010 and 2011 on KSTAR, the NBI-1 system was equipped with one prototype ion source and operated successfully, providing a neutral beam power of 0.7-1.6 MW to the tokamak plasma. The new ion source planned for the 2012 KSTAR campaign had a much more advanced performance compared with the previous one. The target performance of the new ion source was to provide a neutral deuterium beam of 2 MW to the tokamak plasma. The ion source was newly designed, fabricated, and assembled in 2011. The new ion source was then conditioned up to 64 A/100 keV over a 2-hour beam extraction and performance tested at the NB test stand （NBTS） at the Korea Atomic Energy Research Institute （KAERI） in 2012. The measured optimum perveance at which the beam divergence is a minimum was about 2.5μP, and the minimum beam divergent angle was under 1.0° at 60 keV. These results indicate that the 2.0 MW neutral beam power at 100 keV required for the heating of plasma in KSTAR can be delivered by the installation of the new ion source in the KSTAR NBI-1 system.     

用于NBI的红外畸变图像修正方法研究

中性束注入(Neutral Beam Injection,NBI)是等离子体辅助加热和维持最有效的手段之一。目前,红外诊断作为一种快速高效的诊断手段,逐渐用于中性束束品质诊断中。在红外诊断装置中,由于红外相机的光轴与靶平面的垂线呈一定夹角,从而导致采集图像的几何畸变。论文利用坐标变换的方法通过计算机编程实现了红外畸变图的校正,为红外成像应用于中性束诊断奠定了基础。     

Neutral beam deposition in large,finite-beta noncircular tokamak plasmas

A parametric pencil beam model is introduced for describing the attenuation of an energetic neutral beam moving through a tokamak plasma. The nonnegligible effects of a finite beam cross-section and noncircular shifted plasma cross-sections are accounted for in a simple way by using a smoothing algorithm dependent linearly on beam radius and by including information on the plasma flux surface geometry explicitly. The model is bench-marked against more complete and more time-consuming two-dimensional Monte Carlo calculations for the case of a large D-shaped tokamak plasma with minor radiusa=120 cm and elongationb/a=1.6. Deposition profiles are compared for deuterium beam energies of 120–150 keV, central plasma densities of 8×10¹³ to 2×10¹⁴ cm^–3, and beam orientation ranging from perpendicular to tangential to the inside wall.     

Beam Driven Tokamak Fusion Reactors

The recent successes in neutral beam current drive experiments on large tokamaks prompt us to consider the prospect of a beam driven steady state tokamak fusion reactor. A neo-classical theory on the beam driven current, which fully includes the toroidal effects on the induced ion and electron currents and is the most reliable to date, is reviewed in this article. The prospect of steady state tokamaks predicted by the theory may be somewhat pessimistic if the plasma current is sustained only by the beam driven current, because too much beam power is necessary for the current drive. However, thanks to the bootstrap current which was discovered in many tokamaks in recent years, the feasibility of a continuous tokamak operation will probably be highly improved because several tens of percent of the current will be produced by the bootstrap current. The energy gain Q would attain 30 to 50 in the power reactor and about 10 even for next generation (demonstration size) tokamaks.     

The Study of Heat Pulse Propagation on HT—7 Tokamak

The propagation of heat pulses originating from sawtooth activity has been studied on the HT-7 tokamak.Two theoretical models are used for determining electron heat diffusivity from the experimental data measured by a diagnostic system of soft x-ray diode-array.The results show that one model caaled dipole model is more suitable for HT-7 tokamak.In order to improve the signal-to-noise(S/N) ratio of the original signals,over a few tens of sawteeth are averaged to generatc nicc wavcforms.The apace-time evolution is found to be diffusive in character,which is consistent with the theoretical model.The electron heat diffusivity determined from heat pulse propagation is larger than determined from background plasma power balance.The variation of Xe in different discharge phases has been also discussed.     

HL-2AMW级中性束注入系统弧流电源设计

中性束注入是磁约束受控核聚变实验装置中加热等离子体最有效的方法之一。针对中国环流器2号中性束大功率离子源的特点,从系统功能、主电路拓扑结构、控制硬件及控制时序等方面对弧流电源进行设计。整个电源由低位移相交流调压、高压隔离降压变压器、整流滤波和电流快速转移电路4部分组成。IGBT与电阻串联组成电流快速转移阵列电路,与离子源并联,可实现电流单次或多次快速转移、参数远程设定,有效用于强流离子束的引出和保护。选用DSP和CPLD电路技术实现低位与高位控制器。实验数据显示,该电源最大输出为200kW/1000A,纹波小于2％,开关上升下降时间达μs级。目前,该电源已安全运行3年,可靠性高,完全满足装置离子源及系统要求,也可应用于其它等离子体技术应用场合。     

Superconducting Busline Design for HT—7U Tokamak

Superconducting (SC) tokamak HT-7U has seven pairs of buslines connecting toroidal/Poloidal coils and the current leads,These SC buslines(SCBLs) share a common cryostat and are made of the calbe in conduit conductors(CICCs) arranged as a decoupling configuration.In order to reduce the heat loads conducted from the seven current leads with a capacity of 15kA during the magnets cooldown.the buslines with a much lower thermal conduction were employed in comparison with the current leads,and a special cooling loop was designed.