Simultaneous Oxidization of NOx and SO2 by a New Non-thermal Plasma Reactor Enhanced by Catalyst and Additive

The non-thermal plasma as one of the most promising technologies for removing NOx and SO2 has attrm~ted much attention. In this study, a new plasma reactor combined with catalyst and additive was developed to effectively oxidize and remove NOx and SO2 in the flue gas. The experimental results showed that TiO2 could improve the oxidation efficiency of SO2 in the case of applying plasma while having a negative effect on the oxidation process of NO and NOx. With the addition of NH3, the oxidation rates of NOx, NO and SO2 were slightly increased. However, the effect of adding NH3 on NOx oxidation was negative when the temperature was above 200℃.     

A Study of Removing Chlorobenzene by the Synergistic Effect of Catalysts and Dielectric-Barrier Discharge Driven by Bipolar Pulse-Power

In this study, the improvement in the removal of chlorobenzene （C6H5Cl） in the air was investigated by combining dielectric barrier discharge （DBD） driven by bipolar pulse-power with catalysts. Molecular sieve 4A （MS-4A） and MnO2/γ-Al2O3 （MnO2/ALP） as two kinds of catalysts were tested at different positions in a DBD reactor. Catalysts were located either in the discharging area between two electrodes, or just behind the discharging area （in the afterglow area） closed to the outlet. The results indicated that DBD reactor with a bipolar pulse power-supply produced strong instant discharge and energetic particles, which can effectively activate catalysts of MS-4A and MnO2/ALP located in the afterglow area to achieve the synergistic effects on effective fission of chemical bonds of chlorobenzene. It was considered that the gas-chlorobenzene and the chlorobenzene adsorbed on the catalysts were decomposed simultaneously.     

Cu Films Deposited by Unbalanced Magnetron Sputtering Enhanced by ICP and External Magnetic Field Confinement

Metallic copper（Cu） films were deposited on a Si （100） substrate by unbalanced magnetron sputtering enhanced by radio-frequency plasma and external magnetic field confinement. The morphology and structure of the films were examined by scanning electron microscopy （SEM）, atomic force microscope （AFM） and X-ray diffraction （XRD）. The surface average roughness of the deposited Cu films was characterized by AFM data and resistivity was measured by a four-point probe. The results show that the Cu films deposited with radio-frequency discharge enhanced ionization and external magnetic field confinement have a smooth surface, low surface roughness and low resistivity. The reasons may be that the radio-frequency discharge and external magnetic field enhance the plasma density, which further improves the ion bombardment effect under the same bias voltage conditions. Ion bombardment can obviously influence the growth features and characteristics of the deposited Cu films.     

Dipeptide Formation from Amino Acid Monomer Induced by keV Ion Irradiation： An Implication for Physicochemical Repair by Radiation Itself

An identification of Phe dipeptide from L-phenylalanine monomers after keV nitro- gen and argon ion implantation, by using the HPLC （high performance liquid chromatography） and LC-MS（liquid chromatography mass spectrometer） methods is reported. The results showed a similar yield behavior for both ion species, namely： 1） the yield of dipeptides under alkalescent conditions was distinctly higher than that under acidic or neutral conditions; 2） for different ion species, the dose-yield curves tracked a similar trend which was called a counter-saddle curve. The dipeptide formation may implicate a recombination repair mechanism of damaged biomolecules that energetic ions have left in their wake. Accordingly a physicochemical self-repair mechanism by radiation itself for the ion-beam radiobiological effects is proposed.     

Inactivation of Bacillus Subtilis by Atomic Oxygen Radical Anion

UAtomic oxygen radical anion （O-） is one of the most active oxygen species, and has extremely high oxidation ability toward small-molecules of hydrocarbons. However, to our knowledge, little is known about the effects of O- on cells of micro-organisms. This work showed that O- could quickly react with the Bacillus subtilis cells and seriously damage the cell walls a s well as their other contents, leading to a fast and irreversible inactivation. SEM micrographs revealed that the cell structures were dramatically destroyed by their exposure to O-. The inactivation efficiencies of B. subtilis depend on the O- intensity, the initial population of cells and the treatment temperature, but not on the pH in the range of our investigation. For a cell concentration of 10^6 cfu/ml, the number of survived cells dropped from 10^6 cfu/ml to 10^3 cfu/ml after about five-minute irradiation by an O- flux in an intensity of 233 nA/cm^2 under a dry argon environment （30 ℃, 1 atm, exposed size： 1.8 cm^2）. The inactivation mechanism of micro-organisms induced by O- is also discussed.     

Grafting Silane onto Silicate Glass Surface Treated by DBD in Air

Dielectric barrier discharge plasma in air was used to modify glass surface to induce the graft of silane onto the treated surface to increase the possibility of biomolecule immobilization. The plasma treated glass had been characterized by scanning electron microscopy （SEM）, Fourier transform infrared attenuated total reflection spectroscopy, X-ray photoelectron spectroscopy （XPS） and surface water contact angle measurement. The validity of grafting silane onto glass surface was approved by the analysis of water contact angle measurement, SEM and XPS. The grafted silane content was measured by visible absorption spectroscopy using acid Orange-7. It is shown that the grafting density of silane for glass samples increases significantly after plasma treatment.     

Degradation of Anionic Dye Eosin by Glow Discharge Electrolysis Plasma

This paper describes a novel method for the degradation of eosin by using glow discharge electrolysis （GDE）. The effects of various parameters on the removal efficiency were studied. It was found that the eosin degradation could be raised considerably by increasing the applied voltage and the initial concentration, or by decreasing pH of the aqueous solution. Fe^2＋ ion had an evident accelerating effect on the eosin degradation. The degradation process of eosin obeyed a pseudo-first-order reaction. The relationship between the degradation rate constant k and the reaction temperature T could be expressed by Arrhenius equation with which the apparent activation energy Ea of 14.110 kJ· mol^-1 and the pre-exponential factor k0 of 2.065× 10^-1 min^-1 were obtained, too. The determination of hydroxyl radical was carried out by using N, N-dimethyl -p-nitrosoaniline （RNO） as a scavenger. The results showed that the hydroxyl radical plays an important role in the degradation process.     

Scattering of Electromagnetic Waves by Drift Vortex in Plasma

In a quasi-two-dimensional model, the scattering of incident ordinary electromag- netic waves by a dipole-electrostatic drift vortex is studied with first-order Born approximation. The distribution of the scattering cross-section and total cross-section are evaluated analytically in different approximate conditions, and the physical interpretations are discussed. When the wavelength of incident wave is much longer than the vortex radius （kia〈〈1）, it is found that the angle at which the scattering cross-section reaches its maxim depends significantly on the approximation of the parameters of the vortex used. It is also found that the total scattering cross-section has an affinitive relation with the parameters of the plasma, while it is irrelevant to the frequency of the incident wave in a wide range of parameters of the vortex. In a totally different range of parameters when incident wave is in the radar-frequency range （then kia 〈〈 1, the wavelength of incident wave is much shorter than the vortex radius）, the numerical procedure is conducted with computer in order to obtain the distribution and the total expression of the scattering crosssection. Then it is found that the total scattering cross-section in the low frequency range is much larger than that in high frequency range, so the scattering is more effective in the low frequency range than in high frequency range.     

Experimental Research on Plasma Induced by TEA CO2 Laser Propulsion

Results in the air-breathing propulsion experiments with a parabolic light craft and a self-made UV-preionized 100 J TEA CO2 laser device are presented. Air disturbance and the spectrum of the plasma after the interaction of pulsed laser radiation with the light craft were studied. It was found that the focal length of the parabolic light craft had a significant effect on the air-disturbance. Two shock waves were detected for the longer focal length, while only one shock wave detected for the short focal length. The spectrum of the laser-induced plasma, the distribution of the characteristic lines, and the temporal behaviors of the air plasma were studied in detail. The results showed that, the evolution of the laser-induced plasma lasted 20μs, and the plasma spectrum would reach the maximum intensity at 7μs.     

Mixed Wastes Vitrification by Transferred Plasma

Thermal plasma technology provides a stable and long term treatment of mixed wastes through vitrification processes. In this work, a transferred plasma system was realized to vitrify mixed wastes, taking advantage of its high power density, enthalpy and chemical reactivity as well as its rapid quenching and high operation temperatures.
To characterize the plasma discharge, a temperature diagnostic is realized by means of optical emission spectroscopy （OES）. To typify the morphological structure of the wastes samples~ scan- ning electron microscopy （SEM）, and X-ray diffraction （XRD） techniques were applied before and after the plasma treatment.     

Morphology of irradiated PMMA membranes prepared by phase inversion with supercritical CO2

Poly （methyl methacrylate） （PMMA） pellets are irradiated using 60Co gamma-ray in air and successfully formed by hot pressing at constant conditions. The irradiated PMMA membranes are prepared by supercritical carbon dioxide （scCO2） as a physical blowing agent using the pressure quench method. Effects of foaming conditions such as adsorbed dose, saturation temperature, pressure on the morphology and cell size of the microcellular PMMA membranes are investigated in detail. The results showed that the irradiated PMMA membranes possess spherically closed-cell structure with uniform cell size. They have a high cell density compared with virgin PMMA. The cell size uniformity becomes poor at dose lower than 10 kGy, but increases with the dose at dose higher than 10 kGy. The mean cell diameter is less than 10 μm and the cell density increases with increasing dose. The average cell size of irradiated PMMA membranes decreases and cell density increases with increased saturation temperature and pressure. The changes in morphology of membranes are attributed to the gamma-ray radiation and scCO2 synergistic effect.     

Plasma Limiter Based on Surface Wave Plasma Excited by Microwave

A novel plasma limiter, in which the plasma is excited by surface wave, is presented. The breakdown time of some gases filled in the limiter were calculated as a function of gas pres- sure, ionization degree and density of seed electrons under low pressure （0.01 -1 Torr） and high pressure （10 -1000 Torr） cases. The results show that the limiter filled with Xe with a pressure of 0.9 Torr, seed electron density of 10^16 m^-3, and ionization degree of 10^-4, has a breakdown time of approximate 19.6 ns.     

Adsorption behavior of uranyl ions onto amino-type adsorbents prepared by radiation-induced graft copolymerization

Amino-type adsorbents(ATAs) were prepared by radiation-induced graft copolymerization of 4-hydroxybutyl acry late glycidyl ether(HB) onto a polyethylene-coated polypropylene(PE/PP) duplex fiber of a non-woven fabric,and modified with different amines of ethylenediamine(EDA),diethylenetriamine(DETA),triethylenetetramine(TETA) and diethylamine(DEA).The adsorption behavior of uranyl ions onto the ATAs was studied in batch experiments.The effects of the contact time,initial concentration of the ions,temperature,and pH value.The salinity were investigated along with the adsorption kinetics and the adsorption isotherms.The kinetic experimental data followed the pseudo second-order kinetic model,and the adsorption isotherms correlated well with the Langmuir model.The ATAs showed good efficiency in adsorbing uranyl ions,with the best saturation adsorption capacity being 64.26 mg g~(-1) for ATA-DETA within 120 min.The temperature dependence of ATADETA was quite abnormal and the quickest behavior was obtained at 25 ℃.ATAs showed good adsorption capacity over a wide pH range of 4.0-8.5,and HCl could be used in the elution process.Salinity of the solution had great effect on the adsorption capacity,3.5%salinity resulted in a 55%loss of capacity from ATA-DETA.The selectivity of ATA-DETA showed an order of:UO_2~(2+)≈Fe~(3+) Zn~(2+) VO_3~- Co~(2+) Ni~(2+).     

Bromate formation in bromide-containing waters irradiated by gamma rays

The formation of bromate,a classified potential carcinogen,is of great concern when disinfection processes are used for treating high-bromide drinking waters.Bromide-containing aqueous solutions with various additives were irradiated by ~(60)Co γ source.With a 2.0 kGy irradiation of N_2O-saturated solutions at initial bromide concentrations of 180.2μgl~(-1),416.9μgl~(-1),663.1μgl~(-1) and 823.9μgl~(-1).79.5%,84.0%,87.3%and 88.3%of bromide ions were transformed to bromate,respectively.Addomg CO_3~(2-)/HCO_3~- or NO_3~- ions into N_2Osaturated bromide solutions,the amount of bromate ions formed decreased with increasing concentrations of the additives.On the other hand,the bromate concentration was all below the detection limit of 1 μgl~(-1) whenever N_2O was not added to quench e_(aq)~- and H.The results indicated that γ-rays irradiation could be used as a disinfection process,instead of ozonation,to comply with upcoming more stringent regulations,especially in waters containing high concentrations of bromide.     

Mechanical Properties of Thermoplastic Polyurethanes Laminated Glass Treated by Acid Etching Combined with Cold Plasma

To overcome the problem of interlaminar delamination of thermoplastic polyurethane laminated glass, silicate glass was etched with hydrofluoric acid and thermoplastic polyurethane was then treated with cold plasma. Compared with the untreated samples, the interlaminar shear strength of acid etching samples, cold plasma-treated samples and acid etching combined with cold plasma-treated samples increased by 97%, 84% and 341%, respectively. Acid etching combined with cold plasma-treated samples exhibited a higher flexural strength and strain as compared with the untreated samples. The impact energy of acid etching samples, cold plasmatreated samples and acid etching combined with cold plasma-treated samples increased by 8.7%, 8.1% and 11.6%, respectively, in comparison with the untreated samples. FT-IR analysis showed that a large number of -C-O, CO N and CO O C groups appeared on the surface of cold plasma-treated thermoplastic polyurethane, which resulted in the formation of hydrogen bonds. SEM results showed that some pittings formed on the surface of the silicate glass treated by acid etching, which resulted in the formation of a three-dimensional interface structure between tile silicate glass and polyurethane. Hydrogen bonds combined with the three-dimensional interface between silicate glass and polyurethanes co-improved the mechanical properties of thermoplastic polyurethanes laminated glass.     

Deactivating Metal Particle by Optimizing Insulation Configuration in Spark Gap Switch

As a new method to protect the spark gap from metal particle contamination, the effect of the metal inserted insulator on the controlling behavior of metal particles was investigated in a quasi-uniform electric field. Considering that the inserted metal electrodes can decrease the electric field around the insulator and divert the electrostatic force away from the insulator, the method can be used to prevent the particles from moving toward the insulator so as to reduce the possibility of a breakdown. The inserted metal electrodes can reverse the direction of the particles＇ horizontal motion. A study on the insulator shape indicates that the inserted metal electrodes can repulse the particle and improve the particle lifting voltage significantly near the vertical surface of the insulator or ribbed insulator. For the insulator with a tilting surface the inserted metal electrodes have little influence on the particle motion. In addition, the size of the inserted electrodes shows a significant effect on the control of particle motion.     

Characterization of Thin Films Deposited with Precursor Ferrocene by Plasma Enhanced Chemical Vapour Deposition

In this paper, the characterization of thin films, deposited with the precursor ferrocene （FcH） by the plasma enhanced chemical vapour deposition （PECVD） technique, was investigated. The films were measured by Scanning Electronic Microscopy （SEM）, Atomic Force Microscopy （AFM）, Electron Spectroscopy for Chemical Analysis （ESCA）, and Superconducting Quantum Interference Device （SQUID）. It was observed that the film＇s layer is homogeneous in thickness and has a dense morphology without cracks. The surface roughness is about 36 nm. From the results of ESCA, it can be inferred that the film mainly contains the compound FeOOH, and carbon is combined with oxygen in different forms under different supply-powers. The hysteresis loops indicate that the film is of soft magnetism.     

Achieving Better NOx Removal in Discharge Plasma Reactor by Field Enhancement

Application of plasma chemistry for gas cleaning is gaining prominence in recent years, mainly from an energy efficiency point of view. In this paper we conducted a comparative study of NO/NOx removal using two different types of dielectric barrier discharge electrodes, wire- cylinder reactor, pipe-cylinder reactor. Investigations were first carried out with synthetic gases to obtain the baseline information on the NO/NOx removal with respect to the two geometries studied. Further, experiments were carried out with raw diesel exhaust under loaded condition. A high NOx removal efficiency of 90% was observed for the pipe-cylinder reactor as compared to that of 53.4% for the wire-cylinder reactor. Furthermore, for the same energy consumed per NO molecule （about 73 eV/NO molecule）, the removal efficiency increased from 67% for the wire- cylinder to about 98% for the pipe-cylinder which was quite appreciable.     

Surface Modification of SiC Nanoparticles with PMMA by Low Temperature Plasma

An investigation into Poly （methyl methacrylate） （PMMA） grafted onto nano-SiC particles is reported in this study. In our experiment, the grafting polymerization reaction is induced by radio frequency （RF） discharge of N2 plasma treatment of the nanosized powder. FTIR （Fourier transform infrared spectrum）, XPS （X-ray photoelectron spectroscopy） and TGA （Thermogravimetric analysis） results reveal that PMMA is grafted onto the surface of silicon carbide powder, and the crystal structure of the silicon carbide powder observed with XRD （X- ray diffraction） spectra is unchanged before and after the plasma graft polymerization.     

Structure and Mechanical Properties of CrTiAlN/TiAlN Composite Coatings Deposited by Multi-Arc Ion Plating

CrTiAlN/TiAlN composite coatings were deposited on cemented carbide by using a home-made industrial scale multi-arc ion plating system. The samples were studied by X-ray diffraction, scanning electron microscopy （SEM）, microhardness and ball-on-disk testing. The properties of the CrTiAlN/TiAlN coatings were significantly influenced by the microstructure and the deposition time ratio of TiAlN over CrTiAlN layers. With the increase of deposition time ratio, the microhardness of CrTiAlN/TiAlN increased from 28.6 GPa to 37.5 GPa, much higher than that of CrTiAlN coatings. The friction coefficients of the CrTiAlN/TiAlN coatings were higher than those of CrTiAlN coatings against a cemented carbide ball. The microhardness of the CrTiAlN/TiAlN coatings was changed after annealing at 800 ℃, and the friction coefficients of the annealed coatings were increased against the cemented carbide ball.