Comparison Between Micrometer- and Nano-Scale Glass Composites for Sealing Solid Oxide Fuel Cells

The present study compares the feasibility of controlling the properties of a glass composite seal by adding nano- or micron-scale yttria-stabilized zirconia (YSZ) powders to a borate glass used for sealing electrolyte-supported solid oxide fuel cells (SOFCs). The crystallization of the glass composites was found to be independent of the volume fraction of added YSZ, for both sizes of the additive. The variation of the flow properties of both composite seals was measured using a wettability test, and an increase of the contact angle was observed when the volume fraction of additives was increased. The major factor found to decrease spreading of the glass composite was the additive particle size, where shape retention was observed for the nanometer (nm)-YSZ composites while spreading of the micrometer (μm)-YSZ composites was observed under the same testing conditions. Examination of the microstructure showed that initially the Ba-containing glass reacted with YSZ to form a BaZrO₃ compound. Long-time exposure at 800°C caused a large reduction in the coefficient of thermal expansion (CTE), which can be explained by increased formation of BaZrO₃ and further change in glass composition. This change in CTE occurs rapidly for the nm-YSZ composites, which is not observed for the μm-YSZ composites. However, the adverse reactions occurring between the additives and the glass matrix were found to reduce the CTE of the glass composites to a value lower than the recommended limit for a system used for sealing SOFCs.     

Bimodal distribution of filler on viscosity and thermal expansion of glass composites

This paper investigates the bimodal oxide filler system to study the viscous behavior and thermal expansion properties of glass composites. Zinc oxide and cordierite, which are two types of filler, with different average diameters (10 μm and 1 μm, respectively), were considered in a Bi2O3 containing glass with various volume fractions (up to 40 vol%). The experimental results for the composites with the bimodal filler distribution show a reduced viscosity. The viscosity increased from fine particles to coarse particles with an increase in the volume fraction of the composite. Both viscosity and coefficient of thermal expansion (CTE) decreased significantly in the composite with the cordierite filler. The CTE is determined from the volume fraction with respect to particle size and distribution. On the other hand, viscosity is dependent on the particle distribution, particle size, and volume fraction of the composite.     

Improvements in microstructural and mechanical properties of ZrO2 ceramics after addition of BaO

The effects of the addition of BaO on the sinterability, phase balance, microstructure, and mechanical properties of 8 mol% yttria-stabilized cubic zirconia (8YSZ) were investigated using scanning electron microscopy, X-ray diffraction (XRD) analyses, and micro-hardness testing. The 8YSZ powder was doped with 0–15 wt% BaO using a colloidal process. The undoped and BaO-doped 8YSZ specimens were sintered at 1550 °C for 1 h. The XRD analyses results showed that the specimens doped with up to 1 wt% BaO did not exhibit BaO-related peaks, indicating that BaO was completely solubilized in the 8YSZ matrix. However, when more than 1 wt% BaO was added, BaZrO₃-related peaks appeared, suggesting that the overdoped BaO did not dissolve in the 8YSZ matrix but formed a secondary phase of BaZrO₃ at high temperatures. Grain size measurements showed that the grain size of 8YSZ decreased with an increase in the amount of BaO added. The decrease in the grain size was owing to the fact that the grains of BaZrO₃, which precipitated at the grain boundaries and grain junctions of 8YSZ, increased the grain boundary cohesive resistance because of the pinning effect. This resulted in a decrease in the grain boundary mobility, and an increase in the grain boundary energy. Furthermore, while the addition of BaO to 8YSZ caused a slight decrease in the hardness of 8YSZ, the fracture toughness of 8YSZ increased from 1.64 MPa m^1/2 to 2.08 MPa m^1/2, owing to the resulting decrease in the grain size.     

The effect of BaO and Al2O3 addition on the crystallization behaviour of cordierite glass ceramics in the presence of V2O5 nucleant

The effect of V₂O₅ nucleant on crystallization of stoichiometric cordierite glass ceramics in the presence of various amounts of BaO and Al₂O₃ additives were investigated by DTA, XRD and SEM. It was shown that 3 wt.% V₂O₅ and 1.5 wt.% BaO were the optimum amounts of the additives effective in inducing both surface and bulk crystallization in the above glass ceramics.This resulted in ～90 wt.% cordierite after a 3 h heat treatment at 1020 °C. The specimens possessing 4–5 wt.% Al₂O₃ in excess of the stoichiometric cordierite composition, developed mullite along with cordierite in the temperature range of 1045–1055 °C, whereas in the specimen containing 6 wt.% excess Al₂O₃, mullite was detected as the sole crystallization product.     

Electrical and thermal properties of low permittivity Sr2Al2SiO7 ceramic filled HDPE composites

The feasibility of low permittivity Sr₂Al₂SiO₇ (SAS) ceramic filled high density polyethylene (HDPE) composites for substrate and packaging applications has been investigated in this paper. The composites were prepared by the melt mixing and hot pressing techniques. Scanning electron microscopic images of SAS filled HDPE showed the increased connectivity with filler loading. The composites showed excellent relative density (>98%) with low bulk density (<2.40 g cm^?3) and very low moisture absorption (<0.10 wt%). The relative permittivity (ε_r) and the dielectric loss (tan δ) at 1 MHz and at 5 GHz were found to be low and found to increase with filler volume fraction (V_f). The experimentally observed relative permittivity at 5 GHz was correlated with the values proposed by different theoretical models. Among them, effective medium theory (EMT) gave better fit with experimental values except at the highest filler loading (0.50 V_f). Improvement in the thermal properties was also observed with filler content. The coefficient of linear thermal expansion (CTE) was found to decrease with filler content. Thermal conductivity (TC) of the composite was greatly enhanced as a function of filler volume fraction. The composite with 0.50 filler volume fraction showed balanced thermal and dielectric properties with ε_r=4.2, tan δ=3.9×10^?3, TC=2.2 W m^?1 K^?1 and CTE=101 ppm/°C.     

New glass and glass–ceramic sealants for planar solid oxide fuel cells

This work describes the design of three new glass and glass ceramic compositions to join the ceramic electrolyte (YSZ wafer) to the metallic interconnect (Crofer22APU) in planar SOFC stacks. The designed sealants are low-sodium, barium free and boron-oxide free silica-based glasses.The sealing process was optimized for the most promising composition and joined Crofer22APU/glass–ceramic sealant/YSZ samples were morphologically characterized and tested for 300 h in humidified hydrogen atmosphere at the fuel cell operating temperature of 800 °C. The study showed that the use of the glass–ceramic was successful in joining the YSZ ceramic electrolyte to the Crofer22APU metallic interconnect and in preventing severe corrosion effects at the Crofer22APU/glass–ceramic interface after static treatments in humidified hydrogen at 800 °C for 300 h.     

Application of BaO–CaO–Al2O3–B2O3–SiO2 glass–ceramic seals in large size planar IT-SOFC

BaO–CaO–Al₂O₃–B₂O₃–SiO₂ (BCAS) glass–ceramics can be used as sealant for large size planar anode-supported solid oxide fuel cells (SOFCs). BCAS glass–ceramics after heat treatment for different times were characterized by means of thermal dilatometer, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that the coefficients of thermal expansion (CTE) of BCAS glass–ceramics are 11.4×10⁻⁶ K⁻¹, 11.3×10⁻⁶ K⁻¹ and 11.2×10⁻⁶ K⁻¹ after heated at 750 °C for 0 h, 50 h, and 100 h, respectively. The CTE of BCAS matches that of YSZ, Ni–YSZ and the interconnection of SOFC. Needle-like barium silicate, barium calcium silicate and hexacelsian are crystallized in the BCAS glass after heat-treatment for above 50 h at 750 °C. The glass–ceramics green tape prepared by aqueous tape casting can be directly applied in sealing the cell of SOFCs with 10 cm×10 cm. The open circuit voltage (OCV) of the cell keeps 1.19 V after running for 280 h at 750 °C and thermal cycling 10 times from 750 °C to room temperature. The maximum power density is 0.42 W/cm² using pure H₂ as fuel and air as oxidation gas. SEM images show no cracks or pores exist in the interface of BCAS glass–ceramics and the cell.     

Effect of Bi2O3 content on sintering and crystallization behavior of low-temperature firing Bi2O3–B2O3–SiO2 glasses

The sintering behavior of a Pb-free Bi₂O₃–B₂O₃–SiO₂ glass system was examined as a function of Bi₂O₃ content. The glass transition temperature and the crystallization temperature of the glasses decreased with different decreasing gradients as the Bi₂O₃ content increased. The change in temperature affected the sintering behaviors of the glasses. In the case of the 40 mol% Bi₂O₃ addition, large pore accompanied over-firing phenomenon was observed when the sample was sintered over the optimum sintering temperature. However, over-firing was not observed in the sample with 45 mol% of Bi₂O₃ because of the crystallized phases during sintering. When the Bi₂O₃ content was 50–55 mol%, the crystallization temperature became lower than the glass transition temperature, which resulted in the crystallization of glass and it hindered densification.     

Fabrication and thermal expansion properties of ZrW2O8/Zr2WP2O12 composites

ZrW₂O₈/Zr₂WP₂O₁₂ composites were fabricated by sintering ZrW₂O₈–Zr₂WP₂O₁₂ powder mixtures at 1473 K for 1 h, and their negative thermal expansion properties were investigated. The relative density of sintered pure-phase ZrW₂O₈ was 72.3%, while that of the sintered composites was 88.4–92.3%. In the composites, the observed hysteresis in the thermal expansion data was small because of the small difference between the CTEs of ZrW₂O₈ and Zr₂WP₂O₁₂. The CTE of the composites was negative and increased with the Zr₂WP₂O₁₂ content. When the Zr₂WP₂O₁₂ volume fraction in the composites was increased from 0 to 75 vol%, the CTEs of the composites increased from ?9.1 × 10^?6 to ?3.1 × 10^?6 K^?1 and from ?5.0 × 10^?6 to ?1.9 × 10^?6 K^?1 over the temperature ranges of 323–373 and 473–673 K, respectively. In composites with Zr₂WP₂O₁₂ volume fractions of 0–25 vol%, the experimentally obtained CTE values were in good agreement with the calculated values obtained by assuming mixed law behavior.     

Near net-shape fabrication of alumina glass composites

The purpose of the present study is to fabricate alumina glass composites by melt infiltration with better dimensional control through reducing both the presintering and infiltration temperature. Main efforts were put to develop glasses that are chemically compatible with alumina. After extensive investigations, a glass of 21SiO₂–24B₂O₃–35Al₂O₃–15Li₂O–5CaO wt.% was successfully developed. The glass shows good chemical compatibility with alumina at elevated temperatures and low viscosity above 900 °C. Dense alumina glass composites can be fabricated by the melt infiltration process at 950 °C, which is 150 °C lower than the current state-of-art. Investigations showed improved net-shape capability for the newly developed composites, where the total linear shrinkage for the sintering and infiltration at 950 °C is less than 0.1%, as compared with the shrinkage of 0.5% induced by the presintering and infiltration at 1100 °C. Preliminary mechanical tests showed that the fracture strength and toughness of the composites are 303 MPa and 3.4 MPa m^1/2, respectively. The lower processing temperature and the better dimensional control are the major advantages for the newly developed alumina glass composites.     

Orientated crystallization of fresnoite glass-ceramics by using a thermal gradient

The glass with chemical composition (mol%) 33.33 BaO, 16.66 TiO₂, 50.00 SiO₂ was prepared by a conventional melt-quenching method. The glass-ceramics with a Ba₂TiSi₂O₈ crystal was prepared by crystallization of the glasses using a hot stage. The crystals are shown highly orientated along the c-axis perpendicular to the hot surface of the sample. Crystallization was controlled by a diffusion process with surface nucleation. The activation energy for crystallization was about 518 kJ/mol. The mechanism of oriented crystallization was considered in the present paper.     

The influence of nano alumina additions on the coefficient of thermal expansion of a LZS glass–ceramic composition

In this work a 19.58Li₂O·11.10ZrO₂·69.32SiO₂ (mol%) glass–ceramic matrix was prepared and milled in order to determine its coefficient of thermal expansion (CTE) and to study how it is influenced by the addition of nanosized Al₂O₃ particles (1–5 vol%) and submicrometric Al₂O₃ particles (5 vol%). Comminution studies from the LZS parent glass frit showed that a powder with an adequate particle size (3.5 µm) is achieved after 120 min of dry milling followed by a second step of 60 h wet milling. The obtained LZS glass–ceramic samples (fired at 900 °C/30 min) showed an average relative density of ∼98% with zirconium silicate and lithium disilicate as main crystalline phases. Prepared composites with 1, 2.5 and 5 vol% of nanosized Al₂O₃ and 5 vol% submicrometric Al₂O₃ showed average relative densities varying from 97% to 94% as the alumina content increased. The formation of β-spodumene in the obtained composites leads to reduce the CTEs, whose values ranged from 9.5 to 4.4×10⁻⁶ °C⁻¹. Composites with 5% nanosized alumina showed a CTE lower than that of the equivalent formulation with submicrometric alumina.     

Enhanced thermal conductivity of low-temperature sintered borosilicate glass–AlN composites with β-Si3N4 whiskers

The effects of β-Si₃N₄ whiskers on the thermal conductivity of low-temperature sintered borosilicate glass–AlN composites were systematically investigated. The thermal conductivity of borosilicate glass–AlN ceramic composite was increased from 11.9 to 18.8 W/m K by incorporating 14 vol% β-Si₃N₄ whiskers, and high flexural strength up to 226 MPa were achieved along with low relative dielectric constant of 6.5 and dielectric loss of 0.16% at 1 MHz. Microstructure characterization and percolation model analysis indicated that thermal percolation network formation in the ceramic composites led to the high thermal conductivity. The crystallization of the borosilicate microcrystal glass also contributed to the enhancement of thermal conductivity. Such ceramic composites with low sintering temperature and high thermal conductivity might be a promising material for electronic packaging applications.     

Oxidation behaviour of Si3N4–TiN ceramics under dry and humid air at high temperature

The oxidation in air of Si₃N₄-based ceramics containing 35 vol.% of TiN secondary phase and different amounts of sintering additives has been studied at different temperatures up to 1400 °C in dry or humid environment. The oxidation starts by crystal growth of TiO₂ at the surface, then a multilayered scale develops under the rutile layer from 1000 °C. This subscale is composed of silicon nitride in which TiN particles are oxidized to agglomerates of rutile, glass and pores. The oxidation process is controlled by the matter transports, which take place in the intergranular phase. These transport phenomena are affected by the changes in distribution and composition of the glassy phase and by humidity which modifies the glass network structure and thus the in-diffusion rate. From 1200 °C, Si₃N₄ grains are also oxidized, the additional glass formed closes the residual porosities yielding scales more compact and developing an autoprotective behavior. At 1400 °C, glass phase crystallizes into cristobalite and the rutile top layer becomes discontinuous. Only composites with low amounts of sinter additives keep an autoprotective oxidation mode.     

Tuning the interfacial reaction between CaO–SrO–Al2O3–B2O3–SiO2 sealing glass–ceramics and Cr-containing interconnect: Crystalline structure vs. glass structure

In this paper, Al₂O₃ was added to CaO–SrO–B₂O₃–SiO₂ sealing system to tailor the structure of sealing glass–ceramics and glass–ceramics/metal interfacial reaction. The addition of alumina in glasses contributes to increasing fraction of bridging oxygen in silica tetrahedral as well as the change in boron environment from three-fold to four-fold (BO₄ → BO₃). The devitrification tendency of glasses also decreases with increasing Al₂O₃ content. The condensed glass structure and increasing residual glass content play opposite roles on the interfacial reaction, consequently resulting in a maximum fraction of Cr⁶⁺ in reaction couples between Cr₂O₃ and glass containing 6 mole% Al₂O₃ at 700 °C. In addition, the good bonding can be observed at the interface between Cr-containing interconnect (Crofer 22APU) and glass containing 4 mole% Al₂O₃, held at 700 °C for 100 h. The reported results support the suitability of the prepared glass–ceramics as sealing materials for SOFC applications.     

Structural refinement,optical and microwave dielectric properties of BaZrO3

In this work, barium zirconate (BaZrO₃) ceramics synthesized by solid state reaction method and sintered at 1670 °C for 4 h were characterized by X-ray diffraction (XRD), Rietveld refinement, and Fourier transform infrared (FT-IR) spectroscopy. XRD patterns, Rietveld refinement data and FT-IR spectra which confirmed that BaZrO₃ ceramics have a perovskite-type cubic structure. Optical properties were investigated by ultraviolet–visible (UV–vis) absorption and photoluminescence (PL) measurements. UV–vis absorption spectra suggested an indirect allowed transition with the existence of intermediary energy levels within the band gap. Intense visible green PL emission was observed in BaZrO₃ ceramics upon excitation with a 350 nm wavelength. This behavior is due to a majority of deep defects within the band gap caused by symmetry breaking in octahedral [ZrO₆] clusters in the lattice. The microwave dielectric constant and quality factor were measured using the method proposed by Hakki–Coleman. The dielectric resonator antenna (DRA) was investigated experimentally and numerically using a monopole antenna through an infinite ground plane and Ansoft's high frequency structure simulator software, respectively. The required resonance frequency and bandwidth of DRA were investigated by adjusting the dimension of the same material.     

Effect of Al2O3 content on BaO–Al2O3–B2O3–SiO2 glass sealant for solid oxide fuel cell

The glass structure, wetting behavior and crystallization of BaO–Al₂O₃–B₂O₃–SiO₂ system glass containing 2–10 mol% Al₂O₃ were investigated. The introduction of Al₂O₃ caused the conversion of [BO₃] units and [BO₄] units to each other and it played as glass network former when the content was up to 10 mol%, accompanied by [BO₄] → [BO₃]. The stability of the glass improved first and then decreased as Al₂O₃ increased from 2 to 10 mol%, the glass with 5 mol% Al₂O₃ being the most stable one. The wetting behavior of the glasses indicates that excess Al₂O₃ leads to high sealing temperature. The glass containing 5 mol% Al₂O₃ characterized by a lower sealing temperature is suitable for SOFC sealing. Al₂O₃ improves the crystallization temperature of the glass. The crystal phases in the reheated glasses are mainly composed of Ba₂Si₃O₈, BaSiO₃, BaB₂O₄ and BaAl₂Si₂O₈. Al₂O₃ helps the crystallization of BaSiO₃ and BaAl₂Si₂O₈.     

Effect of Al2O3 and K2O content on structure,properties and devitrification of glasses in the Li2O–SiO2 system

The effect of Al₂O₃ and K₂O content on structure, sintering and devitrification behaviour of glasses in the Li₂O–SiO₂ system along with the properties of the resultant glass–ceramics (GCs) was investigated. Glasses containing Al₂O₃ and K₂O and featuring SiO₂/Li₂O molar ratios (3.13–4.88) far beyond that of lithium disilicate (Li₂Si₂O₅) stoichiometry were produced by conventional melt-quenching technique along with a bicomponent glass with a composition 23Li₂O–77SiO₂ (mol.%) (L₂₃S₇₇). The GCs were produced through two different methods: (a) nucleation and crystallization of monolithic bulk glass, (b) sintering and crystallization of glass powder compacts.Scanning electron microscopy (SEM) examination of as cast non-annealed monolithic glasses revealed precipitation of nanosize droplet phase in glassy matrices suggesting the occurrence of phase separation in all investigated compositions. The extent of segregation, as judged from the mean droplet diameter and the packing density of droplet phase, decreased with increasing Al₂O₃ and K₂O content in the glasses. The crystallization of glasses richer in Al₂O₃ and K₂O was dominated by surface nucleation leading to crystallization of lithium metasilicate (Li₂SiO₃) within the temperature range of 550–900 °C. On the other hand, the glass with lowest amount of Al₂O₃ and K₂O and glass L₂₃S₇₇ were prone to volume nucleation and crystallization, resulting in formation of Li₂Si₂O₅ within the temperature interval of 650–800 °C.Sintering and crystallization behaviour of glass powders was followed by hot stage microscopy (HSM) and differential thermal analysis (DTA), respectively. GCs from composition L₂₃S₇₇ demonstrated high fragility along with low flexural strength and density. The addition of Al₂O₃ and K₂O to Li₂O–SiO₂ system resulted in improved densification and mechanical strength.     

Effect of suspension stability on bonding strength and electrochemical behavior of electrophoretically deposited HA–YSZ nanostructured composite coatings

In the present study, HA–YSZ nanostructured composites were deposited on Ti–6Al–4 V substrates by electrophoretic deposition of suspensions containing 0, 10, 20 and 40 wt% YSZ. The stability of each suspension was determined by applying response surface methodology, DLVO theory and zeta potential measurement for different YSZ contents and dispersant concentrations. The maximum zeta potential and electromobility of suspended particles was obtained for the suspension with 20 wt% YSZ. The electrophoretic deposition of HA–YSZ nanostructured composites was carried out at a constant voltage of 20 V for 120 s. The deposition kinetics was studied based on a mass-charge correlating approach under ranges of voltage (20–60 V), time (30–300 s) and wt% YSZ (0–40). The as–deposited and sintered HA–YSZ coatings were characterized by SEM, XRD, DSC–TG and FT–IR analyses. The micro-scratch behavior of coated samples indicated the highest critical contact pressures of crack initiation, P_c1 = 4.50 GPa, crack delamination, P_c2 = 5.14 GPa and fracture toughness, K_IC = 0.622 MPa m^1/2 for HA-20 wt% YSZ sample. The results of potentiodynamic polarization measurements showed that the implementation of 20 wt% YSZ could efficiently decrease the corrosion current density and corrosion rate of coated samples, while corrosion potential and linear polarization resistance were increased.     

Synthesis of glass–ceramics in the CaO–MgO–SiO2 system with B2O3, P2O5, Na2O and CaF2 additives

Glass–ceramics based on the CaO–MgO–SiO₂ system with limited amount of additives (B₂O₃, P₂O₅, Na₂O and CaF₂) were prepared. All the investigated compositions were melted at 1400 °C for 1 h and quenched in air or water to obtain transparent bulk or frit glass, respectively. Raman spectroscopy revealed that the main constituents of the glass network are the silicates Q¹ and Q² units. Scanning electron microscopy (SEM) analysis confirmed liquid–liquid phase separation and that the glasses are prone to surface crystallization. Glass–ceramics were produced via sintering and crystallization of glass-powder compacts made of milled glass-frit (mean particle size 11–15 μm). Densification started at 620–625 °C and was almost complete at 700 °C. Crystallization occurred at temperatures >700 °C. Highly dense and crystalline materials, predominantly composed of diopisde and wollastonite together with small amounts of akermanite and residual glassy phase, were obtained after heat treatment at 750 °C and 800 °C. The glass–ceramics prepared at 800 °C exhibited bending strength of 116–141 MPa, Vickers microhardness of 4.53–4.65 GPa and thermal expansion coefficient (100–500 °C) of 9.4–10.8 × 10⁻⁶ K⁻¹.