Nanoseed-assisted rapid formation of ultrathin ZnO nanorods for efficient room temperature NO2 detection

The influence of ZnO nanoseeds on the formation of ZnO nanorods from ε-Zn(OH)₂ in NaOH solution at 80 °C was investigated, using ZnO nanoparticles with a diameter of 4–10 nm as the seeds. The experimental results indicated that the presence of ZnO nanoseeds promoted the rapid heterogeneous formation of ultrathin ZnO nanorods. Compared with the ZnO submicron rods with a diameter of 0.5–1.0 µm, the ultrathin ZnO nanorods with a diameter of 10–15 nm were found to be more sensitive for detecting NO₂ at room temperature owing to their higher variation of channel conduction to the diameter.     

Hydrothermal synthesis of dumbbell-shaped ZnO microstructures

Dumbbell-shaped ZnO microstructures have been successfully synthesized by a facile hydrothermal method using only Zn(NO₃)₂·6H₂O and NH₃·H₂O as raw materials at 150 °C for 10 h. The results from X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM) show that the prepared ZnO samples exhibit dumbbell-shaped morphology and hexagonal wurtzite structure. The length of ZnO dumbbells is about 5–20 μm, the diameters of the two ends and the middle part are about 1–5 μm and 0.5–3 μm, respectively. The dumbbell-shaped ZnO microstructures may be formed by self-assembly of ZnO nanorods with 1–5 μm in length and 100–200 nm in diameter. The photoluminescence (PL) spectrum of dumbbell-shaped ZnO microstructures at room temperature shows three emission peaks at about 362, 384 and 485 nm.     

Growth of hexagonal prism ZnO nanorods on Zn substrates by hydrothermal method and their photoluminescence

Hexagonal prism ZnO nanorods were successfully grown on Zn substrates by the 120 °C and 24 h hydrothermal reaction of the solutions with pH of 9–12. Results from XRD, SEM, TEM, SAED and HRTEM showed that the as-synthesized products were wurtzite ZnO with the shape of hexagonal prism nanorods grown along the [0 0 1] direction with smooth prismatic side planes. The PL spectra showed strong emission band at 543 nm in the green-yellow region due to the recombination of electrons trapped in singly ionized oxygen vacancies and photoexcited holes. This facile, reproducible and effective low-cost approach is promising for the future large-scale synthesis of wurtzite ZnO nanostructures for different applications in nanotechnology.     

Synthesis of Ag3PO4–ZnO nanorod composites with high visible-light photocatalytic activity

Ag₃PO₄ nanoparticles with 50–100 nm in size distributed on the surface of ZnO nanorods with ca. 20 nm in diameter and 1–2 μm in length have been synthesized by a facile method. The Ag₃PO₄–ZnO nanorod composites had much higher photocatalytic activity toward degradation of Rhodamine B (RhB) under visible light irradiation than pure ZnO nanorods, and had better recyclability and stability than pure Ag₃PO₄ nanoparticles. The Ag₃PO₄–ZnO nanorod composite with the molar ratio of Ag₃PO₄:ZnO = 1:40 exhibited the highest photodegradation efficiency of RhB (93%), which was 1.5 times of pure ZnO nanorods.     

Ultra-thin cerium oxide nanostructures through a facile aqueous synthetic strategy

In this work, synthesis of ultra-thin 2D CeO₂ nanoribbons is reported for the first time along with rod-shaped nanostructures via a surfactant free aqueous method. CeO₂ nanoribbons of length >100 nm have been synthesised through a mild reaction route involving ammonia precipitation and subsequent heating and ageing at 0 °C. 2D nanostructures are proposed to be formed as a result of self-assembly of CeO₂ molecules. The ribbons exhibited amorphous X-ray diffraction pattern and TEM showed a ribbon like morphology with crystal facets of ～0.33 nm spacing corresponding to (1 1 1) plane of CeO₂. HR-TEM confirmed that the nanorods are enclosed by {1 1 1} planes and have preferentially grown in {1 1 0} direction. The surface area of the powder containing majority nanorods is 82 m²/g and their average pore size is ～3 nm. The nanostructures exhibited optical band gaps dominated by the regular quantum confinement effect as well as presence of defects.     

ZnO thin film nanostructures for hydrogen gas sensing applications

A ZnO thin film-based gas sensor was fabricated using a SiO₂/Si substrate with a platinum comb-like integrated electrode and heating element. The structural characteristics, morphology, and surface roughness of the as-grown ZnO nanostructure were investigated. The film revealed the presence of a c-axis oriented (002) phase with a grain size of 20.8 nm. The sensor response was tested for hydrogen concentrations of 50, 70, 100, 200, 400, and 500 ppm at the optimum operating temperature of 350 °C. The sensitivities towards 50 and 200 ppm of hydrogen gas at 350 °C were approximately 78% and 98%, respectively. A linear response was observed for hydrogen concentrations within the range of 50 ppm–200 ppm. These results demonstrated the potential application of the ZnO nanostructure for the fabrication of cost-effective and high-performance gas sensors.     

Tailoring of morphology and orientation of LaNiO3 films from polymeric precursors

The aim of this work was to prepare lanthanum nickel oxide (LaNiO₃, LNO) thin films of different morphology and orientation. The precursor solutions were prepared by a chemical method from citric salts of lanthanum and nickel. Films were deposited using spin-on technique on Si (1 0 0) substrates. Tailoring of the films orientation and morphology has been attained through two thermal treatment processes with different heating devices: tubular furnace (process 1) and hot plate (process 2). Films were annealed at 600 and 700 °C, with heating rates: 20 °C/min (process 1) and 1 °C/min (process 2). Annealing times were from 30 min to 20 h. LNO films were characterized by AFM and X-ray diffraction analysis. Depending on the heating process applied, the obtained films showed very different structures, from completely amorphous to well crystallized and highly oriented. Films treated by process 1 were polycrystalline, had smaller oval grains and lower roughness parameters than films heated on a hot plate. Due to the low heating rate and heating from the substrate side, films obtained through process 2 were highly (1 1 0) oriented with elongated grains aligned along one direction.     

The effects of pulse repetition rate on the structural,surface morphological and UV photodetection properties of pulsed laser deposited Mg-doped ZnO nanorods

The Mg_0.05Zn_0.95O (MZO) nanorod array (NRA) films have been successfully grown onto SiO₂/ n-Si substrates by pulsed laser deposition (PLD) without any template or seed layer and the influence of pulse repetition rate (3 to 15 Hz) of a 248 nm KrF excimer laser on their crystallinity, surface morphology and UV photodetection properties were systematically investigated. All the samples show the hexagonal wurtzite phase with a preferential c-axis orientation and the optimum crystallization of the MZO NRAs occurs at 5 Hz. FE-SEM analysis revealed that the growth of MZO NRAs is strongly influenced by the pulse repetition rate. It was observed that the average film thickness increases almost linearly with the pulse repetition rate and the MZO nanorod arrays grown at 5 Hz exhibits best surface area. Moreover, the room temperature UV photodetection properties of the samples were investigated in metal–semiconductor–metal (MSM) planar configurations and are found to be strongly driven by the pulse repetition rate dependent crystalline and surface morphological features. The device current–voltage (I–V) characteristics were measured under dark and UV light conditions. Then, the photocurrent and responsivity were measured with the variation of optical power density and applied voltage, respectively. Transient photoresponse studies show an exceedingly stable and fast switching UV photoresponse for the photodetector having MZO nanorods grown at 5 Hz, which demonstrates highest responsivity of 17 mA/W upon 2 mW/cm² UV illumination (365 nm), at 5 V bias.     

Ethanol sensing properties of tungsten oxide nanorods prepared by microwave hydrothermal method

Tungsten oxide nanorods have been prepared by a simple microwave hydrothermal (MH) method via Na₂SO₄ as structure-directing agent at 180 °C for 20 min. The structure and morphology of the products are characterized by X-ray powder diffraction (XRD) and transmission electron microscopy (TEM). The obtained nanorods are about 20–50 nm in diameter and several micrometers in length. The ethanol sensing property of as-prepared tungsten oxide nanorods is studied at ethanol concentration of 10–1000 ppm and working temperature of 370–500 °C. It was found that the sensitivity depended on the working temperatures and also ethanol concentration. The results show that the tungsten oxide nanorods can be used to fabricate high performance ethanol sensors.     

Large scale ZnO nanorod-based UV sensor induced by optimal seed layer

Due to various effective parameters involved in synthesis process, the fabrication of large-scale, uniform, and high performance nanostructure-based UV sensor has recently been a challenge for practical applications. Here, we solve the problem by employing central composite rotatable design (CCRD) to generate an experimental program to offer data for modelling the individual and interactive effects of different parameters on UV sensing properties. In this work, large-scale and highly uniform ZnO nanorods (NRs) were hydrothermally grown on the glass substrate. Applying CCRD methodology, the substrates were pre-coated with different seed layers by dip-coating technique. Using counter and surface plots and also AFM, FE-SEM, and XRD analysis, the role of seed layer on nucleation mechanism, morphological, structural and UV sensing of ZnO NRs are systematically discussed. In addition, it has been found that the seed layer prepared under precursor concentration of 0.45 M, withdrawal speed of 3.5 cm min⁻¹, dip-coating numbers of 3, and annealing temperature of 400 °C provides the best conditions for growing UV-sensitive ZnO NRs with optimal seed layer. Moreover, calculating lack-of-fit, pure errors, and coefficient of determination shows that the model has appropriate goodness-of-fit and repeatability. Our study is expected to pave a way for the growth of large scale NR-based UV sensors with optimum sensitivity and responsivity.     

Transparent semiconductor zinc oxide thin films deposited on glass substrates by sol–gel process

Transparent semiconductor ZnO thin films were spin-coated onto alkali-free glass substrates by a sol–gel process. The influence of ZnO sols synthesized via different solvents (2-ME, EtOH or IPA) on the surface morphologies, microstructures, optical properties and resistivities of the obtained films were investigated. The as-coated films were annealed in ambient air at 500 °C for 1 h. X-ray diffraction results showed all polycrystalline ZnO thin films to have preferred orientation along the (0 0 2) plane. The surface morphologies, optical transmittances and resistivity values of the sol–gel derived ZnO thin films depended on the solvent used. The ZnO thin films synthesized with IPA as the solvent exhibited the highest average transmittance 92.2%, an RMS roughness of 4.52 nm and a resistivity of 1.5 × 10⁵ Ω cm.     

Structural,optical and photocatalytic properties of ZnO nanorods: Effect of aging time and number of layers

ZnO thin films were prepared by sol–gel dip coating method onto glass substrates. The effects of aging time of the starting solution (2, 10 and 30 days) and the number of coats (2, 5 and 10 coatings) on structural, morphological and optical properties were investigated. Photocatalytic efficiency was also assessed. X-ray diffraction analysis indicates that all the films exhibit a Zincite-type structure with a preferred grains orientation along the [002] direction. The preferred orientation factor (POF) increases with aging time while the crystallite size decreases. The field emission scanning electron microscopy observations reveals nanorods morphology. The length of ZnO nanorods increase with increasing number of layers whereas their length decreases as a function of aging time while adopting a random orientation. A high optical transparency is observed for all ZnO thin films, ranging from 90 up to 96%. Methylene Blue (MB) dye photocatalytic degradation was found increases with aging time, reaching almost 94% after 10 h under UV irradiation. The apparent reaction rate (K_app) obtained by Langmuir-Hinshelwood model increases with increasing aging time from, from 0.218 h⁻¹ for 2 days to reach a steady state around 0.270 h⁻¹. Nevertheless, a small variation of K_app was recorded when varying the number of coats; 0.223–0.226 h⁻¹.     

Template-free synthesis of neodymium hydroxide nanorods by microwave-assisted hydrothermal process,and of neodymium oxide nanorods by thermal decomposition

Based on the 150 °C and 1 h microwave-assisted hydrothermal reaction of Nd(NO₃)₃ dissolved in deionized water with pH 10 adjusted by concentrated NH₄OH solution, the phase and morphology of the product, characterized by XRD, SEM and TEM analyses, were specified as hexagonal Nd(OH)₃ nanorods 50 nm in diameter and 700 nm long, growing along the [0 0 1] direction. TGA analysis showed the evaporation of adsorbed water and dehydration of Nd(OH)₃ to synthesize the final pure Nd₂O₃ product. With 500 °C and 2 h calcination of the Nd(OH)₃ self-template precursor, Nd₂O₃ nanorods were synthesized, retaining both the morphology and growth direction of the precursor.     

ZnO-capped nanorod gas sensors

This paper reports on the synthesis of pristine α-Fe₂O₃ nanorods and Fe₂O₃–ZnO core–shell nanorods using a combination of thermal oxidation and atomic layer deposition (ALD) techniques; the completed nanorods were then used for ethanol sensing studies. The crystal structure and morphology of the synthesized nanostructures were examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The sensing properties of the pristine and core–shell nanorods for gas-phase ethanol were examined using different concentrations of ethanol (5–200 ppm) at different temperatures (150–250 °C). The XRD and SEM revealed the excellent crystallinity of the Fe₂O₃–ZnO core–shell nanorods, as well as their uniformity in terms of shape and size. The Fe₂O₃–ZnO core–shell nanorod sensor showed a stronger response to ethanol than the pristine Fe₂O₃ nanorod sensor. The response (i.e., the relative change in electrical resistance R_a/R_g) of the core–shell nanorod sensor was 22.75 for 100 ppm ethanol at 200 °C whereas that of the pristine nanorod sensor was only 3.85 under the same conditions. Furthermore, under these conditions, the response time of the Fe₂O₃–ZnO core–shell nanorods was 15.96 s, which was shorter than that of the pristine nanorod sensor (22.73 s). The core–shell nanorod sensor showed excellent selectivity to ethanol over other VOC gases. The improved sensing response characteristics of the Fe₂O₃–ZnO core–shell nanorod sensor were attributed to modulation of the conduction channel width and the potential barrier height at the Fe₂O₃–ZnO interface accompanying the adsorption and desorption of ethanol gas as well as to preferential adsorption and diffusion of oxygen and ethanol molecules at the Fe₂O₃–ZnO interface.     

Low-temperature synthesis of CdWO4 nanorods via a hydrothermal method

Cadmium tungstate (CdWO₄) nanorods were successfully synthesized via a hydrothermal process and characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and photoluminescent spectra techniques (PL). A pure monoclinic phase of well-crystallized CdWO₄ nanorods, with lengths of 250–400 nm and widths of 30–60 nm, could be readily synthesized at as low temperature as 70 °C.The CdWO₄ nanorods showed a PL emissions peak at 435 nm.     

Effect of O2 plasma pretreatment on structural and optical properties of ZnO films on PES substrate by atomic layer deposition

ZnO films were deposited on the O₂ plasma treated polyethersulfone (PES) substrates by atomic layer deposition. X-ray diffraction (XRD) measurements reveals that the grains in ZnO films show strongly (0 0 2) preferential orientation, when the duration of plasma pretreatment increases. The decreased grain size and improved crystallinity results in the decreased surface roughness of ZnO films. In contrast, when the duration of plasma pretreatment increases to 60 min, the surface roughness increases again due to the increased grain size and worse crystallinity. In photoluminescence measurement, slight blue shift of near-band-edge emission occurs with increasing duration of plasma pretreatment up to 30 min.     

Facile synthesis of ZnO nanostructures and enhancement of their sinterability via short-time cryo-milling

Zinc oxide (ZnO), a wide band-gap semiconductor, has received a great interest due to its potential applications in various fields both as nanostructures and as sintered compacts. In this study, we report on the synthesis of the ZnO nanostructures and facilitation of their sintering for the production of fine-grained dense compacts. The facile synthesis of gram scale ZnO nanostructures was achieved by thermal decomposition of zinc acetate dihydrate (Zn(Ac)₂·2H₂O) or Zn(Ac)₂·2H₂O/graphite mixtures at 300 °C for 12 h. Thermal decomposition of Zn(Ac)₂ resulted in the formation of mostly ZnO nanoparticles with wurtzite structure along with ZnO nanorods, while the addition of graphite significantly promoted the growth of ZnO nanowires. Microstructural and phase properties of the obtained ZnO nanostructures were determined by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high resolution TEM (HRTEM) techniques, all of which revealed the successful synthesis of high quality ZnO nanostructures. In addition to synthesis and characterization of the ZnO nanostructures, we report on the enhancement of their sinterability by a subsequent cryogenic milling for a short duration of 5 min. As a result of the applied cryo-milling, fabrication of highly dense (96.2%) sintered compacts with fine grain sizes (572 nm) could be achieved after pressureless sintering at 1000 °C for 2 h.     

Enhanced NO2 sensing properties of Zn2SnO4-core/ZnO-shell nanorod sensors

Zn₂SnO₄-core/ZnO-shell nanorods were synthesized using a two-step process: synthesis of Zn₂SnO₄ nanorods the thermal evaporation of a mixture of ZnO, SnO₂, and graphite powders, followed by atomic layer deposition (ALD) of ZnO. The nanorods were 50–250 nm in diameter and a few to a few tens of micrometers in length. The cores and shells of the nanorods were face-centered cubic-structured single crystal Zn₂SnO₄ and wurtzite-structured single crystal ZnO, respectively. The multiple networked Zn₂SnO₄-core/ZnO-shell nanorod sensors showed a response of 173–498% to NO₂ concentrations of 1–5 ppm at 300 °C. These response values are 2–5 times higher than those of the Zn₂SnO₄ nanorod sensor over the same NO₂ concentration range. The NO₂ sensing mechanism of the Zn₂SnO₄core/ZnO-shell nanorods is discussed.     

Durable superhydrophobic Zn/ZnO/TiO2 surfaces on Ti6Al4V substrate with self-cleaning property and switchable wettability

Durable superhydrophobic (SHP) Zn/ZnO/TiO₂ surfaces with dendritic structures on Ti₆Al₄V substrate were obtained by chemical etching, electrodeposition and following annealing process. The resultant coatings electrodeposited at ?1.5 V for 10 min and annealed at 190 °C for 60 min showed fine superhydrophobicity with a water contact angle of 160° and a rolling angle less than 1°, showing excellent rolling-off and self-cleaning properties. The morphology, chemical components and growth mechanism of samples were investigated by scanning electron microscopy (SEM), X-ray diffraction pattern (XRD), Energy-dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). Surface tribological properties were characterized by a universal mechanical tester (UMT). The as-prepared Zn/ZnO/TiO₂ surface still kept excellent SHP stability after exposure to the air, buried in soil and cold storage at 5 °C in the fridge for one year, as well as excellent repellence to some daily-used liquids such as coke, coffee, red wine, milk and tea. The surface can be reversibly switched between superhydrophobicity and superhydrophilicity by alternating UV illumination and dark storage or heating, which offer possibilities to widen future applications.     

Preparation,characterization of 1D ZnO nanorods and their gas sensing properties

The 1D ZnO nanorods (NR's) were grown with Zinc (Zn) ion precursor concentration variation on seed layer glass substrate by the low temperature hydrothermal method and utilized for nitrogen dioxide (NO₂) gas sensing application. Zn ion precursor concentration varied as 0.02, 0.03, 0.04, 0.05 and 0.06 M and thin films were characterized for structural, morphological, optical, electrical, surface defect study and gas sensing properties. All the film showed dominant orientation along the (002) direction, the intensity of the peak vary with the length of the nanorods. SEM cross images confirmed that nanorods had vertical alignment perpendicular to the plane of the substrate surface. The PL intensity of oxygen vacancy related defects for prepared samples was found to be linearly proportional to gas sensing phenomena. This result in good agreement with the theoretical postulation that, oxygen vacancies plays the important role for adsorption sites to NO₂ molecule. The gas sensing performance was studied as a function of operating temperature, Zn ion precursor concentration variation, and gas concentration. The maximum gas response is 113.32–100 ppm NO₂ gas at 150 °C for 0.05 M sample out of all prepared samples. Additionally, ZnO thin film sensor has potential to detect NO₂ as low as 5 ppm.