Synthesis and biocompatibility of porous nano-hydroxyapatite/collagen/alginate composite

Porous nano-hydroxyapatite/collagen/alginate (nHAC/Alginate) composite containing nHAC and Ca-crosslinked alginate is synthesized biomimetically. This composite shows a significant improvement in mechanical properties over nHAC material. Mechanical test results show that the compressive modulus and yield strength of this composite are in direct proportion to the percentage of Ca-crosslinked alginate in the composite. Primary biocompatibility experiments in vitro including fibroblasts and osteoblasts co-culture with nHAC/alginate composite indicated the high biocompatibility of this composite. Therefore the composite can be a promising candidate of scaffold material for bone tissue engineering.     

In Vitro Characterizations of PLLA/β-TCP Porous Matrix Materials and RMSC-PLLA-β-TCP Composite Scaffolds

To develop a novel degradable poly (L-lactic acid)/β-tricalcium phosphate (PLLA/β-TCP) bioactive materials for bone tissueengineering, β-TCP powder was produced by a new wet process. Porous scaffolds were prepared by three steps, i.e. solventcasting, compression molding and leaching stage. Factors influencing the compressive strength and the degradation behaviorof the porous scaffold, e.g. weight fraction of pore forming agent-sodium chloride (NaCl), weight ratio of PLLA: β-TCP,the particle size of β-TCP and the porosity, were discussed in details. Rat marrow stromal cells (RMSC) were incorporatedinto the composite by tissue engineering approach. Biological and osteogenesis potential of the composite scaffold weredetermined with MTT assay, alkaline phosphatase (ALP) activity and bone osteocalcin (OCN) content evaluation. Resultsshow that PLLA/β-TCP bioactive porous scaffold has good mechanical and pore structure with adjustable compressive strengthneeded for surgery. RMSCs seeding on porous PLLA/     

纳米羟基磷灰石/壳聚糖-羧甲基纤维素复合支架材料的研究

用冷冻干燥法制备了不同比例的纳米羟基磷灰石/壳聚糖-羧甲基纤维素(n-HA/CS-CMC)无机/有机复合多孔支架材料, 并探讨了其复合机理及无机组分n-HA对复合支架的结构形貌、力学性能、体外降解性能的影响. 结果表明, 其复合支架主要是通过无机组分n-HA均匀分散充填在CS-CMC聚电解质有机网络结构中形成的, 且三组分间有较强的化学键合. 无机组分n-HA的加入使孔结构变得不规则, 孔隙率略有减小, 使复合支架的抗压缩强度提高, 并且可使其体外降解速度减慢. 无机组分n-HA含量为40\%复合支架材料的性能最佳, 有望用作骨组织工程支架材料.     

Needle-like nano hydroxyapatite/poly(l-lactide acid) composite scaffold for bone tissue engineering application

In this paper, a new nano-hydroxyapatite / poly (l-lactide acid) (nHAP/PLLA) composite scaffold comprising needle-like nHAP particles was prepared. In the first step, the identification and morphology of chemically synthesized HAP particles were determined by XRD, EDX, FTIR and SEM analyses. The needle-like nHAP particles with an average size of approximately 30–60 nm in width and 100–400 nm in length were found similar to needle-like bone nano apatites in terms of chemical composition and morphology. In the second step, nHAP and micro-sized HAP (mHAP) particles were used to fabricate HAP filled PLLA (HAP/PLLA) composites scaffolds using solid–liquid phase separation method. The porosity of scaffolds was up to 85%, and their average macropore diameter was in the range of 64–175 µm. FTIR and XRD analyses showed the presence of molecular interactions and chemical linkages between HAP particles and PLLA matrix. The compressive strength of nanocomposite scaffolds could high up to 8.46 MPa while those of pure PLLA and microcomposite scaffolds were 1.79 and 4.61 MPa, respectively. The cell affinity and cytocompatibility of the nanocomposite scaffold were found to be higher than those of pure PLLA and microcomposite scaffolds. Based on the results, the newly developed nHAP/PLLA composite scaffold is comparable with cancellous bone in terms of microstructure and mechanical strength, so it may be a suitable alternative for bone tissue engineering applications.     

相分离法构建聚乳酸/纳米羟基磷灰石复合纳米纤维支架及性能

通过液.液相分离法构建纳米纤维聚左旋乳酸/蚋米羟基磷灰石(NF-PLLA/nHA)仿生复合支架,利用扫描电镜、压缩测试、微量二喹啉甲酸(BCA)法、X射线衍射及差示扫描量热等手段对其进行表征.结果显示,nHA均匀馕嵌在PLLA纳米纤维间隙中,不影响其纳米纤维结构且明显提高力学性能.同时,nHA的引入还能增加对牛血清白蛋...     

骨组织工程用纳米羟基磷灰石/ 壳聚糖多孔支架材料的制备及性能表征

以16.7%(质量分数)的柠檬酸水溶液作溶剂,通过粒子沥滤法制备了 n HA/CS多孔材料,并对其进行了IR、XRD、SEM、孔隙率及力学性能测试。结果表明n HA/CS复合材料中羟基磷灰石呈弱结晶状态,复合前后两组分的化学组成未发生显著变化,但两相间发生了相互作用。多孔材料呈高度多孔结构,孔壁上富含微孔,孔间贯通性高;复合材料/致孔剂质量比为1时,多孔材料的孔隙率为 53%,其抗压强度可达17 MPa左右,可以满足组织工程支架材料的要求。     

In vitro investigation of nanohydroxyapatite/poly(<Emphasis Type="SmallCaps">l</Emphasis>-lactic acid) spindle composites used for bone tissue engineering

Calcium phosphate ceramics such as synthetic hydroxyapatite and tricalcium phosphate are widely used in the clinic, but they stimulate less bone regeneration. In this paper, nano-hydroxyapatite/poly(l-lactic acid) (nano-HA/PLLA) spindle composites with good mechanical performance were fabricated by a modified in situ precipitation method. The HA part of composite, distributing homogenously in PLLA matrix, is spindle shape with size of 10–30 nm in diameter and 60–100 nm in length. The molar ratio of Ca/P in the synthesized nano-HA spindles was deduced as 1.52 from the EDS spectra, which is close to the stoichiometric composition of HA (Ca/P & 1.67). The compress strength is up to 150 MPa when the HA content increase to 20 %. The in vitro tests indicate that HA/PLLA bio-composites have good biodegradability and bioactivity when immersed in simulated body fluid solutions. All the results suggested that HA/PLLA nano-biocomposites are appropriate to be applied as bone substitute in bone tissue engineering.     

Preparation and characterization of dense nanohydroxyapatite/PLLA composites

Synthetic bone graft substitutes based on PLLA have been largely studied during the past decade. PLLA/hydroxyapatite composites appear as promising materials for large bone defect healing. In this study dense PLLA/nano-hydroxyapatite composites were prepared by hot pressing. Dense samples were investigated rather than porous scaffolds, in order to shed light on possible correlations between intrinsic mechanical properties and nano-hydroxyapatite concentration. Hydroxyapatite deagglomerated by wet attrition milling, and further dispersed into chloroform was used (median diameter = 80 nm). Particle size distribution measurements and transmission electron microscopy show evidence that particle size and dispersion are maintained throughout the successive steps of composite processing. Mechanical properties were tested (uni-axial and diametral compression tests) as a function of nano-hydroxyapatite content. Increasing concentrations of nano-hydroxyapatite (0, 25 and 50 wt.%) increase the Young's modulus and the mechanical strength of the composite; at the same time, the failure mechanism of the material changes from plastic to brittle. Young's modulus over 6 GPa and uniaxial compressive strength over 100 MPa have been achieved. These values expressed in terms of intrinsic tensile and shear strengths indicate that 50 wt.% nano-hydroxyapatite containing samples develop properties comparable to those of cortical bone. PLLA/nano-hydroxyapatite composites are thus promising candidates to develop bioresorbable porous bone substitutes showing superior mechanical performance.     

A study on the in vitro degradation of poly(L-lactide)/chitosan microspheres scaffolds

Recent research shows that the addition of chitosan microspheres (CMs) to poly(L-lactide) (PLLA) can result in a composite scaffold material with improved biocompatibility and mechanical properties for tissue engineering applications. However, research regarding the influence of CMs on scaffold degradation is absent in the literature. This paper presents a study on the in vitro degradation of scaffolds made from PLLA with CMs. In this study, the PLLA/CMs scaffolds with a 25% ratio of CMs to PLLA were immersed in phosphate-buffered saline (PBS) solution at 37°C for 8 weeks. The in vitro degradation of the scaffolds was investigated using micro-computed tomography (μCT), weight loss analysis, Raman spectroscopy, and differential scanning calorimetry (DSC). Microstructure changes during degradation were monitored using μCT. The μCT results were consistent with the results obtained from Raman spectra and DSC analysis, which reflected that adding CMs into PLLA can decrease the degradation rate compared with pure PLLA scaffolds. The results suggest that PLLA/CMs scaffold degradation can be regulated and controlled to meet requirements imposed a given tissue engineering application.     

Fabrication and characterization of nano composite scaffold of poly(l-lactic acid)/hydroxyapatite

To mimic the nano-fibrous structure of the natural extracellular matrix, a nano composite scaffold of poly(l-lactic acid)/hydroxyapatite(PLLA/HAP) was fabricated by a thermally induced phase separation method. The characterization of the composite scaffold showed that the scaffold had a nano-fibrous PLLA network (fiber size 100–750 nm), an interconnective microporous structure (1–10 μm) and high porosity (>90%). HAP was homogeneously distributed in the scaffold, as a result, the compressive modulus of PLLA/HAP (80:20, w/w) increased to 3.15-fold compared with that of a pure PLLA scaffold. Incorporating HAP into PLLA network also buffered the pH decline in vitro degradation and enhanced the protein adsorption of the composite scaffold significantly. The new nano composite scaffold is potentially a very promising scaffold for tissue engineering.     

PLLA–collagen and PLLA–gelatin hybrid scaffolds with funnel-like porous structure for skin tissue engineering

Abstract

In skin tissue engineering, a three-dimensional porous scaffold is necessary to support cell adhesion and proliferation and to guide cells moving into the repair area in the wound healing process. Structurally, the porous scaffold should have an open and interconnected porous architecture to facilitate homogenous cell distribution. Moreover, the scaffolds should be mechanically strong to protect deformation during the formation of new skin. In this study, the hybrid scaffolds were prepared by forming funnel-like collagen or gelatin sponge on a woven poly(l-lactic acid) (PLLA) mesh. The hybrid scaffolds combined the advantages of both collagen or gelatin (good cell-interactions) and PLLA mesh (high mechanical strength). The hybrid scaffolds were used to culture dermal fibroblasts for dermal tissue engineering. The funnel-like porous structure promoted homogeneous cell distribution and extracellular matrix production. The PLLA mesh reinforced the scaffold to avoid deformation. Subcutaneous implantation showed that the PLLA–collagen and PLLA–gelatin scaffolds promoted the regeneration of dermal tissue and epidermis and reduced contraction during the formation of new tissue. These results indicate that funnel-like hybrid scaffolds can be used for skin tissue regeneration.     

Effect of collagen fibril formation on bioresorbability of hydroxyapatite/collagen composites

Porous hydroxyapatite/collagen (HAp/Col) composite is a promising biomaterial and a scaffold for bone tissue engineering. The effect of fibril formation of Col in the porous composite on bioresorbability and mechanical strength was investigated. The fibril formation, in mixing a self-organized HAp/Col nanocomposite and sodium phosphate buffer at a neutral condition, occurred during incubation at 37 °C, resulting in gelation of the mixture. The porous composites with and without the incubation were obtained by freeze-drying technique, in which macroscopic open pores were formed. The compressive strength of the porous composite with the incubation (34.1 ± 1.6 kPa) was significantly higher than that without the incubation (28.0 ± 3.3 kPa) due to the fibril formation of Col. The implantations of the porous composites treated with a dehydrothermal treatment in bone holes revealed that bioresorption was clearly depended on the fibril formation. The bioresorbability in vivo was almost matched to the in vitro test using enzymatic reaction of collagenase.     

Hydrogels of collagen/chondroitin sulfate/hyaluronan interpenetrating polymer network for cartilage tissue engineering

The network structure of a three-dimensional hydrogel scaffold dominates its performance such as mechanical strength, mass transport capacity, degradation rate and subsequent cellular behavior. The hydrogels scaffolds with interpenetrating polymeric network (IPN) structure have an advantage over the individual component gels and could simulate partly the structure of native extracellular matrix of cartilage tissue. In this study, to develop perfect cartilage tissue engineering scaffolds, IPN hydrogels of collagen/chondroitin sulfate/hyaluronan were prepared via two simultaneous processes of collagen self-assembly and cross linking polymerization of chondroitin sulfate-methacrylate (CSMA) and hyaluronic acid-methacrylate. The degradation rate, swelling performance and compressive modulus of IPN hydrogels could be adjusted by varying the degree of methacrylation of CSMA. The results of proliferation and fluorescence staining of rabbit articular chondrocytes in vitro culture demonstrated that the IPN hydrogels possessed good cytocompatibility. Furthermore, the IPN hydrogels could upregulate cartilage-specific gene expression and promote the chondrocytes secreting glycosaminoglycan and collagen II. These results suggested that IPN hydrogels might serve as promising hydrogel scaffolds for cartilage tissue engineering.     

PLLA–collagen and PLLA–gelatin hybrid scaffolds with funnel-like porous structure for skin tissue engineering

In skin tissue engineering, a three-dimensional porous scaffold is necessary to support cell adhesion and proliferation and to guide cells moving into the repair area in the wound healing process. Structurally, the porous scaffold should have an open and interconnected porous architecture to facilitate homogenous cell distribution. Moreover, the scaffolds should be mechanically strong to protect deformation during the formation of new skin. In this study, the hybrid scaffolds were prepared by forming funnel-like collagen or gelatin sponge on a woven poly(l-lactic acid) (PLLA) mesh. The hybrid scaffolds combined the advantages of both collagen or gelatin (good cell-interactions) and PLLA mesh (high mechanical strength). The hybrid scaffolds were used to culture dermal fibroblasts for dermal tissue engineering. The funnel-like porous structure promoted homogeneous cell distribution and extracellular matrix production. The PLLA mesh reinforced the scaffold to avoid deformation. Subcutaneous implantation showed that the PLLA–collagen and PLLA–gelatin scaffolds promoted the regeneration of dermal tissue and epidermis and reduced contraction during the formation of new tissue. These results indicate that funnel-like hybrid scaffolds can be used for skin tissue regeneration.     

磷酸钙骨水泥/明胶复合组织工程支架材料的制备及其结构与性能

磷酸钙骨水泥组织工程支架材料具有良好的生物相容性和骨传导性,是一种良好的骨组织工程支架材料,但是这种材料存在力学性能差的缺点,限制了它的应用.本文采用生物相容性良好的可降解明胶材料与磷酸钙骨水泥支架进行复合,制备出的明胶/磷酸钙骨水泥复合支架材料,其压缩强度可达3.7MPa,比复合前磷酸钙支架材料的强度提高了37倍,而且材料具有良好的柔韧性,适合用作为非承重部位骨组织缺损修复用组织工程支架材料.     

分级多孔壳聚糖/聚乳酸复合支架的制备及骨修复性能

为了仿生莲藕内部的贯穿大孔结构,以生物相容性好的壳聚糖(CS)作为基质材料,利用冰粒致孔、石蜡模具和冰模具成型3种成型方法制备了分级多孔CS支架材料,然后与力学强度较高的聚乳酸(PLLA)复合,制备网络互穿CS/PLLA复合支架。通过SEM、压缩强度测试和兔股骨髁骨缺损模型对CS/PLLA复合材料的形貌、力学强度和骨修复性能进行了表征。结果表明:利用冰模具制备的CS/PLLA复合支架能可控、批量制备,具有微米-毫米分级多孔结构,大孔孔径约为2mm,内部均匀分布着孔径约为60μm的贯穿微孔,并在微孔内形成密集的PLLA絮状网络结构。干态复合材料的压缩强度和模量分别比纯CS支架的提高了6倍和15倍。体内植入实验结果表明,CS/PLLA复合材料能够促进骨缺损的愈合,并随着新骨的形成,复合材料逐渐被降解吸收。     

溶胶-凝胶生物活性玻璃与胶原复合多孔支架的生物相容性研究

实验前期用冷冻干燥法合成一种溶胶?凝胶生物活性玻璃(BG/COL)与粗胶原纤维复合的组织工程支架. 本实验将支架与鼠骨髓间充质干细胞(rMSCs)共同培养, 评价支架材料的细胞相容性. 并将复合了成骨细胞的支架材料植入裸鼠皮下, 探讨其异位成骨的性能. 研究结果显示rMSCs可以在BG/COL多孔支架材料表面成功粘附、铺展、并向多孔支架内部迁移, 随着培养时间的延长, 双链DNA(ds DNA)数量增多, 细胞增殖情况与对照组差异明显. 将种在复合材料上的骨髓间充质干细胞诱导培养14d后切片染色, 其碱性磷酸酶(ALP)和钙素表达均呈强阳性. 体内植入实验的裸鼠健康状况良好, 伤口完全愈合, 6w后BG/COL周边及内部有骨组织和血管生成. 由此证明, 这种新型的复合多孔支架材料具有良好的生物相容性, 其复合了成骨细胞的组织工程骨具有良好的诱导成骨的性能, 因此这种材料是理想的应用于骨组织修复和再生的组织工程支架材料.     

壳聚糖/磷灰石-硅灰石复合多孔支架材料的制备与性能

以磷灰石-硅灰石(AW)生物活性多孔玻璃陶瓷支架材料为基体,采用物理包被法制备了壳聚糖(CS)/AW复合多孔支架材料,通过红外图谱分析、扫描电镜、光学显微镜、强度检测等分析测试方法,研究了复合材料的组成、微观结构、力学和矿化性能。结果发现：复合材料与AW多孔支架材料基体相比,仍具有三维贯通且分布均匀的孔隙结构,孔径尺寸约 100～500μm,孔隙率为80%左右,且力学性能明显增强,平均抗压强度可达3.11 MPa,比多孔AW支架材料基体的平均抗压强度提高了8.3倍。体外模拟体液浸泡实验表明,复合材料具有较高的矿化功能,预示材料具有较好的生物活性。这种复合材料可望作为人体非承重部位的植入骨修复体和组织工程支架使用。     

介孔纳米羟基磷灰石/左旋聚乳酸复合材料的制备及性能

为考察介孔纳米羟基磷灰石(MHA)/左旋聚乳酸(PLLA)复合材料的性能,以十六烷基三甲基溴化铵(CTAB)为模板合成MHA,采用溶液相分离结合粒子沥滤法制备了不同纳米粒子含量的MHA/PLLA多孔支架复合材料,考察了其抗压缩性能和淬断面微观结构。采用溶液浇注法制备了MHA/PLLA复合膜,并对其拉伸性能和拉伸断面微观结构进行了研究。FTIR、XRD、TEM和氮气吸附测试等结果显示:合成的MHA具有典型的晶体结构、介孔结构和较高的比表面积。力学测试结果显示:在发生10%压缩形变时,填料含量为1%、5%和10%的MHA/PLLA多孔支架复合材料的抗压缩强度随填料含量增加而提高,与相应含量的纳米羟基磷灰石(HA)/PLLA多孔支架复合材料相比,分别提高了约37.0%、67.7%和144.7%。在填料含量为5%和10%时,MHA/PLLA复合膜的拉伸强度较HA/PLLA复合膜分别提高约38.7%和46.1%,拉伸模量分别提高约35.4%和14.5%。而且MHA/PLLA复合膜具有更高的断裂伸长率,填料含量为1%、5%和10%时断裂伸长率分别较HA/PLLA复合膜提高约91.3%、79.7%和96.1%。FESEM结果显示:尤其当填料含量较高时,MHA/PLLA多孔支架复合材料或复合膜中填料粒子分布较HA/PLLA中均匀。结果表明:与HA/PLLA复合材料相比,随着MHA含量增加,MHA/PLLA复合材料具有更好的力学性能,MHA在PLLA基体中分布相对更均匀。     

CPP/PLLA软骨组织工程支架复合材料初步研究

采用溶媒投放、颗粒滤取技术制备出CPP/PLLA软骨组织工程支架复合材料,测试了该复合材料的物理力学性能和降解性能。研究结果表明,CPP/PLLA软骨组织工程支架复合材料具有高的孔隙率(90%)、良好的生物降解性能和物理力学性能,以及三维连通、微孔、网状微观结构,故该复合材料有希望成为软骨组织工程支架材料之一。