小型化缝隙加载圆极化及宽带微带贴片天线设计

提出了一种十字形缝隙加载的小型宽带及圆极化微带贴片天线的设计方法。该天线通过在方形贴片上加载一个大尺寸的十字形缝隙实现天线的尺寸缩减,介质基片采用由FR4和空气层组成的层叠结构,在缝隙中嵌入L型枝节,只需通过调整枝节上同轴线馈电点的位置来获得圆极化或宽带阻抗匹配。ANSYS HFSS仿真分析表明,天线的圆极化带宽（AR≤3 dB）为1.7%,阻抗带宽（VSWR≤2）为5.8%,天线在宽带范围内具有稳定的增益,峰值增益为7.8 dB,同时贴片面积缩减了52.3%。改变馈电点的位置可调节两个谐振频率使天线阻抗带宽达到9.4%,比传统的微带贴片天线阻抗带宽提高了114%。     

容性加载的宽带紧凑型圆极化超表面天线

针对当前超表面圆极化天线研究中存在的尺寸大、带宽与小尺寸无法兼顾等问题,提出了一种宽带紧凑型圆极化超表面天线。该天线采用跨层容性加载技术,通过在方形超表面结构上方加载跨层寄生贴片来引入跨层电容,从而降低谐振频点,实现超表面结构的小型化。同时,这种跨层容性加载超表面结构也具有极化相关特性,将其与45°斜耦合馈电缝隙结合,能够在小尺寸下实现具有宽带特性的圆极化超表面天线。测试结果表明,该天线在辐射口径为0.4 λ₀×0.4 λ₀的情况下,-10 dB阻抗带宽为39.56%(5.82～8.69 GHz);3 dB轴比带宽可达26.98%(6.54～8.58 GHz)。该天线具有圆极化辐射性能良好、宽带、小型化和低剖面等优点,为现代宽带无线通信系统天线的实现提供了一种技术选择。     

单馈电双模方形微带天线及圆极化实现收稿

基于展开理论,给出了沿贴片对角线馈电时方形微带天线的内场分布和输入阻抗公式.通过在贴片四周切割缝隙,有效地降低了天线双主模的谐振频率并实现了圆极化辐射,讨论了缝隙长度与天线极化之间的关系.为实现微带天线的小型化提供了一种新途径,给出了UHF波段天线设计实例.     

单点馈电高增益圆极化三角形微带贴片天线设计

提出了一种单点同轴线馈电小型化高增益圆极化三角形微带贴片天线的设计方法。通过在三角形贴片的中心开一个十字形槽获得圆极化及尺寸缩减,同时在接地板上开三个同尺寸三角形槽提高天线的增益,通过调节三角形槽的尺寸在保持圆极化的情况下准确调节天线的谐振频率。HFSS仿真数据表明,当天线工作于2.43 GHz时,阻抗带宽和圆极化带宽分别为120 MHz(4.9%),30 MHz(1.2%),增益为3.5 d B。与传统的小型化方形贴片天线相比,该天线具有更小的贴片面积和更宽的工作带宽。     

无线通讯用小型无人机载天线

基于无人小飞机的有效载荷和有限空间要求,设计和制作了用于其通讯系统中ISM频段的高性能圆极化微带的一种中心开槽、边缘Y形两侧缝隙加载的变异方形微带贴片结构天线,给出了该天线的仿真结果,描述了圆极化天线的测试方法。测试结果表明,天线指标基本满足系统使用要求,波束宽度为±45°,增益达到4.5dB i,尺寸缩小约36%。将这种天线应用到无人小飞机系统中,可以方便地与射频模块集成,无线收发信机输出得到了良好的波形。实验结果表明,此缝隙加载圆极化微带天线能满足该无人小飞机电子系统实现无线图像及数据实时通信的要求,这将使得该系统的小型化成为可能。     

小型圆极化环形微带天线的设计

提出一种新的小型圆极化环形微带天线,通过在环形贴片内外边缘非主要辐射区域开一组狭长缝隙获得小型化特性,在环形贴片内边缘135°、315°处相对位置开一对调谐窄缝隙实现圆极化,并用带状线在环形贴片内边缘馈电.这种天线表现出了极好的圆极化特性而且很容易在低频段匹配到50Ω,与普通带状线馈电圆极化环形微带天线相比,天线谐振频率下降,尺寸缩小了近50%.     

一种右旋圆极化非谐振波导缝隙阵列天线设计

文中提出一种基于能量传输理论的非谐振波导缝隙阵列设计方法,设计了一款右旋圆极化非谐振波导缝隙阵列天线.圆极化由加载在波导缝隙上的切角正方形波导圆极化腔实现,文中分析了腔体的各设计参数对圆极化特性的影响,实现了圆极化腔与波导缝隙的分离设计.设计的8×8阵列天线工作在17 GHz,主频处能量辐射效率大于94％,主瓣增益25...     

应用于智能交通系统的小型化圆极化微带天线

提出了一种应用于智能交通系统的小型化圆极化微带天线。该天线由一个开缝的方形贴片及围绕方形贴片的两级寄生贴片组成,通过模式解调实现圆极化,并利用寄生贴片增加带宽和提高天线增益。测试结果表明,天线的-10 dB 阻抗带宽为10. 9%,3 dB 轴比带宽为2. 7%,在中心频率5. 8 GHz 处的增益为5. 4 dBi,交叉极化不低于21 dB。天线尺寸为25 mm×25 mm×1. 6 mm,与其它应用于智能交通系统的天线相比,该天线具有更小的平面尺寸。     

单馈电双模方形微带天线及圆极化实现

基于展开理论，给出了沿贴片对角线馈电时方形微带天线的内场分布和输入阻抗公式，通过在贴片四周切割缝隙，有效地降低了天线双主模的谐夺频率并实现了圆极化辐射，讨论了缝隙长度与天线极化之间的关系。为实现微带天线的小型化提供了一种新途径，给出了UHF波段天线设计实例。     

宽频带圆极化缝隙螺旋天线的设计

研究了一种宽阻抗带宽和宽圆极化轴比带宽的缝隙螺旋天线。天线印制在由FR4 介质基板构建的 方形柱状结构的内外表面,两组长短不同的缝隙螺旋臂印制在介质基板外表面并延伸至天线顶部;一条弯折的微带 线作为馈电网络印制在介质基板内表面,通过对各缝隙耦合馈电,实现天线宽阻抗带宽和轴比带宽。实测结果表 明:天线尺寸为0. 111λ0 ×0. 111λ0 ×0. 221λ0(λ0 为北斗B2 中心频率1. 207 GHz 对应的自由空间波长),S11 ≤ -10 dB 的阻抗带宽为1. 158~1. 778 GHz,轴比≤3 dB 的圆极化带宽为1. 133~1. 918 GHz。该天线采用缝隙螺旋结构,通过 简易的馈电网络实现天线小型化和宽频带特性,在卫星导航系统中具有较好的应用前景。     

Circularly polarized co-designed filtering annular slot antenna

In this paper, a compact circularly polarized co-designed filtering annular slot antenna (ASA) is proposed. The antenna comprises a distributed capacitor-loaded annular slot radiator to produce circular polarization (CP) radiation, which is seamlessly integrated with a microstripline bandpass filter (BPF) to enhance out-of-CP-band suppression. Two tightly coupled arc branches protruding into the annular slot are used to provide the required perturbation capacitance. The filter is designed by employing three concentric arc-shaped coupled microstripline resonators. The ground plane is shared by the annular slot radiator and the filter to reduce size occupation. It is found that the proposed antenna can not only yield high frequency selectivity, but also obtain widened CP bandwidth under the assistance of the filtering circuit. An antenna prototype has been fabricated and measured, showing that the antenna achieves a 10 dB return loss impedance bandwidth of around 13.7%, enclosing a 3 dB axial ratio (AR) bandwidth of more than 10.6%. Details of design considerations and experimental results are presented and discussed.     

Printed ring slot antenna for circular polarization

A new design of a microstrip-line-fed circularly polarized printed ring slot antenna is proposed. Circular polarization (CP) radiation of the proposed design is achieved by introducing proper asymmetry in the ring slot structure and feeding the ring slot using a microstrip line at 45° from the introduced asymmetry. The asymmetry introduced in the proposed design is a meandered-slot section and the proposed CP design can be applied to printed square and annular ring slot antennas. Prototypes of the proposed design have been implemented. Experimental results show that good CP radiation performances are obtained and the 3 dB axial-ratio CP bandwidths obtained for the square and annular ring slot antennas are about 4.3% and 3.5%, respectively     

Circularly Polarized Square Ring Slot Antenna with Arrow‐Shaped Structure

A novel design of a compact square‐ring slot microstrip antenna for achieving circular polarization (CP) operation is proposed and experimentally studied. By using an arrow‐shaped slot structure as a radiating element, the resonant frequency of the proposed antenna is significantly lowered, which can lead to a large size reduction for fixed frequency operation. The CP radiation characteristics are achieved by loading with proper asymmetry, which can be placed diagonally. A prototype of the proposed design is implemented and its performance is measured. Measured results show that radiation patterns with good CP characteristics are obtained at the resonant frequency.     

Broadband circularly polarized CPW-fed slot antenna array for millimeter wave application

A broadband and circularly polarized 1×4 linear antenna array composed of CPW-fed slot elements for millimeter wave application is discussed. Through a special short-circuiting stub perturbation method, the circular ring slot element achieves circular polarization and a broad bandwidth. Through a parallel feeding network, the array achieves a broad impedance bandwidth of 19% with VSWR?2 and CP bandwidth of 18.4% with AR?3 dB and has a peak gain of about 6.8 dB.     

SIW cavity-backed circularly polarized square ring slot antenna with wide axial-ratio bandwidth

In the proposed work, Substrate Integrated Waveguide (SIW) cavity-backed circularly polarized slot antenna for wideband operation is proposed. A square-ring-slot is etched on the top of the SIW cavity, used for radiation To generate the circularly polarized (CP) wave, the slot is placed slightly offset from the centroid of the cavity. By finely optimizing the antenna dimensions, it exhibits a wide axial-ratio (AR) bandwidth of 789 MHz (7.1%) ranging from 10.64 to 11.45 GHz. Moreover, the radiating slot is excited by an SIW based feed by an inductive window, which lead to a wide impedance matching over 1.74 GHz ranging from 9.92 to 11.67 GHz. Due to the SIW cavity-backing structure, the antenna offers unidirectional radiation patterns while maintaining a low-profile and planar compatibility. To validate the proposed design, the antenna is fabricated and experimentally tested in terms of reflection coefficients, AR, gain, and radiation patterns. The simulated and measured results reveal good mutual agreement. Moreover, the proposed antenna is very useful for wideband applications operating in X-band (8–12 GHz)     

一种面向无线通信应用的宽频带圆极化天线阵

提出了一种新型宽频带2×2方形缝隙槽圆极化天线阵.天线阵包含一个连续旋转馈电结构、4个非对称U型馈电枝节和一个方形槽接地板.与传统圆极化天线阵所采用的L型馈电枝节不同,首次提出了一种新型非对称U形馈电枝节来改善天线的圆极化性能.利用这些枝节和缝隙槽作为微扰元素,缝隙槽天线阵可以激发多重圆极化谐振模式,进而产生宽频带的圆...     

RCS reduction and gain enhancement of SRR inspired circularly polarized slot antenna using metasurface

In this work, a novel Circularly Polarized (CP) slot antenna is proposed for low RCS and high gain applications. The proposed antenna is designed in two phases. Initially, a metasurface is designed, which is composed of two similar artificial magnetic conductor (AMC) unit cells arranged orthogonally in chessboard-like configuration for broadband RCS reduction. Then, the CP slot antenna is designed by placing dual SRR on the backside of the slot for impedance matching and to achieve circular polarization. Detailed analysis is conducted to investigate the performance of metasurface loaded CP slot antenna. The proposed antenna shows 10 dB RCS reduction over the bandwidth of 41.3% at boresight direction compared to CP slot antenna. The maximum in-band and out-of-band RCS reduction achieved is 24 dB and 20 dB, respectively. The maximum gain of the antenna is also increased by 2.7 dB as a result of parasitic radiation of the metasurface and an improvement in overall performance of the antenna is observed by the employment of metasurface. Measured results of the fabricated prototype are in good agreement with the simulated results.     

Inset microstripline-fed circularly polarized microstrip antennas

Circular polarization (CP) designs of inset microstripline-fed microstrip antennas are proposed. Three designs with a single slit, two pairs of slits, and three pairs of slits are experimentally studied. Good CP performances of the proposed antennas are achieved. For the design with three pairs of slits studied here, the center CP frequency is also seen to be lowered by about 33% compared to the case without slits, which suggests that an antenna size reduction as large as 55% can be obtained if the proposed design is used in place of a conventional CP design at a fixed frequency.     

Miniaturized wideband dual linearly and circularly polarized printed square slot antenna for multiradio wireless systems

A dual symmetrical coplanar waveguide (CPW)-fed small size wideband printed square slot antenna (SSA) with dual linearly and circularly polarized radiation capability is presented. The antenna is composed using a square slot, two symmetrical orthogonal CPW feed lines connected to horizontal and vertical arm of L-shaped radiator, an embedded parasitic inverted-L strip at the lower left corner of the square ground slot and engraving slots in the ground plane. Circular polarization (CP) is achieved due to two orthogonal CPW feed lines and a common L-shaped radiator. Isolation between ports is improved by engraving slots at the lower left corner of ground plane and embedded parasitic inverted-L strip. The sense of dual-polarization can be changed in pass-band by changing the port excitation. Measured antenna reveals that an 84.4% (4.6 GHz, 3.15–7.75 GHz) −10 dB impedance bandwidth (IBW) and about 33% (2.03 GHz, 5.12–7.15 GHz) 3-dB axial ratio bandwidth (ARBW). Isolation between ports <−16 dB is achieved over usable CP band.