X波段SICL小型化带通滤波器的设计

为有效减小X波段滤波器的尺寸,减小通带损耗,对基片集成同轴线(SICL)结构进行了研究,提出一种阶跃阻抗(SIR)型SICL带通滤波器,并针对SICL谐振腔与其他平面电路的连接设计了一种由共面波导(CPW)向SICL谐振腔提供激励的平面结构,以便滤波器的测量。仿真结果表明,滤波器通带特性优异,其中心频率为10 GHz,带宽为1.5 GHz,尺寸为13 mm×7 mm,插入损耗为-0.8 dB。     

单槽双频微波带通滤波器设计与实现

在方形贴片上采用单槽线代替相互正交双槽线的方法设计出一款结构简单、紧凑的双频段带通滤波器。详细讨论了滤波器结构参数对滤波器性能的影响,并以2.45/5.2GHz双通带滤波器的设计为例,通过仿真优化得到了各结构参数,制作了相应的样品。测试结果表明：该滤波器在2.45GHz通带内回波损耗为20dB,通带内最小插损为0.9dB,相对带宽为10%;5.2GHz通带内回波损耗33.6dB,通带内最小插损为0.37dB,相对带宽为13.4%,其总体尺寸比文献中正交双槽线结构的滤波器缩小48%。     

具有宽阻带和高共模抑制的差分滤波器设计北大核心CSCD

将阶跃阻抗谐振器与叉指耦合结构及扇形加载枝节相结合,设计了一款差分带通滤波器。该差分滤波器实现了极宽的差模阻带,并且通过引入非对称加载枝节,实现了抑制水平为16.7 dB的超宽共模抑制特性。此外,该差分滤波器在差模通带内的共模抑制水平可达63.1 dB。对设计的滤波器进行了制作和测试,测得滤波器的中心频率为2.94 GHz,相应的3 dB频带范围为2.85~3.03 GHz。该滤波器具有小型化的特点,电路尺寸仅为20.87 mm×14.96 mm,最终的测试结果和仿真结果吻合良好。     

基于DGS和SIR单元的超宽阻带低通滤波器设计

为了解决传统的微带线低通滤波器尺寸偏大,阻带较窄的问题,采用阶梯阻抗谐振(SIR)单元加载哑铃型缺陷地结构(DGS)单元设计了一个五阶微带低通滤波器,并通过在主传输线两侧添加并联开路枝节,以补偿DGS微带线的特性阻抗。测试结果表明:该滤波器结构尺寸21.6mm×8mm,3dB截止频率4GHz,通带内平均驻波比小于1.5,阻带范围5GHz～35GHz。实现了滤波器结构尺寸的减小和超宽阻带。     

基于新型谐振器的超宽带带通滤波器

采用两个新型四阶阶梯阻抗谐振器设计出一种新型超宽带带通滤波器,四个1/4波长的耦合线被平行放置于输入输出端,起到增加耦合强度的作用,三个谐振频率被调整在超宽带带宽(3.1 GHz～10.6 GHz)内。通过优化后,该滤波器在通带内具有五个传输极点,频带宽度在3.6 GHz～10.5 GHz,通带内回波损耗优于15 dB,最小插入损耗为0.6 dB,满足超宽带的传输要求。仿真结果显示,文中设计的滤波器具有小型化、低插入损耗和较好的带外特性等优点。     

应用于北斗L、S频点的新型双频滤波器设计

提出了一种应用于北斗短报文波段（即L和S频点）的背靠背E形双频滤波器设计。该滤波器由两对公共馈电的背靠背E形谐振器并联组成,上方为背靠背E形的微带阶跃阻抗谐振器,下方为背靠背E形的缺陷阶跃阻抗谐振器。通过等效阻抗分析、表面电流仿真、参数优化得到滤波器的结构,滤波器尺寸为34 mm×21 mm×0.762 mm。实测结果表明,该滤波器的两个中心频点分别为1.62 GHz和2.53 GHz,相对带宽分别为8%和3%,带内插入损耗均小于2.2 dB,回波损耗均大于11.8 dB,相邻通带间的隔离度大于15 dB。测试结果与仿真结果基本吻合。     

基于阶梯阻抗发夹谐振器的小型低通滤波器

提出一种基于阶梯阻抗发夹谐振器的小型化微波低通滤波器,该滤波器仅由包含一节微带线的阶梯阻抗发夹谐振器构成。设计结果表明,滤波器3dB通带从DC(Direct Current)到2GHz,回波损耗优于10dB,且插入损耗从DC到1.7GHz时优于0.5dB,带外抑制从2.9～4GHz优于20dB。仿真结果和实验结果吻合良好。这种滤波器尺寸小,易制造,且具有陡峭的截止频率响应特性,可应用于许多微波系统中。     

超宽带四通道开关滤波器的设计

基于砷化镓(GaAs)工艺,利用ADS软件仿真设计了一款超宽带四通道开关滤波器芯片,频率覆盖了6GHz～20GHz,尺寸为仅3.2mm×2.4mm×0.1mm.该开关滤波器芯片由两个单刀四掷开关和四个带通滤波器电路组合而成.实物测试结果显示,在通带内插入损耗≤10dB,端口回波损耗≥15 dB,带外抑制达到了40dB....     

一种基于SIR结构的三通带带通滤波器

应用双指耦合结构和枝节加载谐振器（Stub-loaded Resonator,SLR）实现了一款基于阶梯阻抗谐振器（Stepped Impedance Resonator,SIR）的滤波器。该滤波器具有3个通带,带外抑制较好,工作频段提高。通过调整阻抗比可调节第二、三通带的谐振频率;SLR结构能够增加通带数量;SLR结构和双指耦合结构均能改善滤波器的S参数。HFSS软件仿真表明,3个通带的中心频率分别为3.5 GHz、6.6 GHz、9.2 GHz,对应的分数带宽分别为5.7%、3%、2%,S11分别为-18 dB、-22 dB、-24 dB,通带内的S21分别为-1.8 dB、-1 dB、-1 dB。电路的测量结果与仿真结果较为吻合。该滤波器在5G通信的低频段具有应用前景。     

基于双模开环谐振器的双频带滤波器设计

基于开环双模谐振器设计了一种双频带通滤波器,由两个中心重合的正方形开口环谐振器组成。分析该谐振器的奇偶模谐振频率与传输零点,每个通带内有两个谐振模式。该滤波器中心频率分别为4.5 GHz和6.5 GHz,3 dB相对带宽FBW分别为11%、5%,两通带带内插入损耗分别小于0.6 dB、1.4 dB,带内回波损耗分别优于19.5 dB、16.5 dB,高频处阻带抑制达到50 dB,两通带之间隔离度达到53 dB,尺寸仅为6 mm×11 mm×1.09 mm。     

Current-mode continuous-time filters using complementary current mirror pairs

A design of current-mode continuous-time filters for low voltage and high frequency applications using complementary bipolar current mirror pairs is presented. The proposed current-mode filters consist of simple bipolar current mirrors and capacitors and are quite suitable for monolithic integration. Since the filters are based on the integrator type of realization, the proposed method can be used for a wide range of applications. The frequency of the filters can easily be changed by the DC controlling current. A fifth-order Butterworth and a third-order leapfrog filter with tunable cutoff frequencies from 20 MHz to 100 MHz are designed as examples and simulated by SPICE using standard bipolar parameters.     

Inverse Ultraspherical Filters

The inverse ultraspherical filter is derived and its properties analyzed. It is shown that the inverse ultraspherical filter has smaller transition band than the inverse Chebyshev filter under certain circumstances while still maintaining the maximally flat passband characteristic. Filter pole and zero calculations are described and typical magnitude and delay responses generated. Nomographs of inverse ultraspherical filters are also provided for determining filter order and for possible magnitude response optimization.Celestino A. Corral was born in Havana, Cuba. He earned his Bachelors, Masters and Ph.D. degrees in electrical engineering from the University of Miami, Florida, in 1985, 1987, and 1993, respectively. He completed his Ph.D. program under a Patricia Roberts Harris fellowship. From 1988 to 1990 Dr. Corral was a Member of the Technical Staff at Sandia National Laboratories, Albuquerque, New Mexico, where he was involved in the analysis, modeling, and design of custom circuits for piezoelectric sensor components. In 1994, he joined Scientific-Atlanta in Atlanta, Georgia, as an Associate Staff RF Engineer and worked on communication systems and specialized microwave software. In 1997 he was Senior Design Engineer at Origin Data Systems in Boca Raton, Florida, where he had multiple roles in system, hardware, and software development for a novel asset management/RFID system. Currently, Dr. Corral is a Distinguished Member of the Technical Staff in Motorola Labs, Plantation, Florida, and is involved in ultra-wideband, wideband, and propagation research. His interests include circuit and filter theory, communication systems, numerical analysis, signal processing, and constrained optimization. He has published over twenty-five journal and conference papers, has six patents filed, and two trade secrets.Dr. Corral was principal recipient of the Myril B. Reed Best Paper Award for the 40th Midwest Symposium on Circuits and Systems in 1997. Dr. Corral is also the principal recipient of the Ambrose Fleming Premium for IEE Proceedings on Circuits, Devices, and Systems, 2000. Dr. Corral is a Senior Member of IEEE and a member of Omicron Delta Kappa, Tau Beta Pi, and Eta Kappa Nu honor societies.     

波导带通滤波器的精确设计和快速优化

介绍了采用三维微波电磁场仿真软件快速提取直接耦合波导带通滤波器耦合窗口参数的方法,并提出了优化最终模型的快速扫描技术.全波仿真及实验结果表明,该方法能满足波导带通滤波器快速精确设计的要求.     

Design of two-dimensional directional filters

A directional filter has a passband extending fully along a straight line passing through the origin. In its original form the transformation technique, a powerful tool for designing two-dimensional FIR filters, is not useful to design such a filter. In this communication we suggest a few analytical and optimisation-based methods to design directional filters using the transformation technique. The superiority of the proposed methods over existing techniques is demonstrated.     

一种基于CIC滤波器的有效锐化方法研究

介绍了对积分梳状滤波器（CIC滤波器）的有效锐化。所提出的锐化滤波器的结构由两个主要部分组成：一个梳状滤波器的级联部分和一个锐化滤波器部分。所提出的方案使得滤波器中锐化部分的工作速率比输入速率大为降低，其频谱响应特性比传统的也有所改进。通过MATLAB仿真，可看出改进锐化后的滤波器性能更优。     

Miniaturized dielectric waveguide filters

Design techniques for a new class of integrated monolithic high-permittivity ceramic waveguide filters are presented. These filters enable a size reduction of 50% compared to air-filled transverse electromagnetic filters with the same unloaded Q-factor. Designs for Chebyshev and asymmetric generalised Chebyshev filter and a diplexer are presented with experimental results for an 1800 MHz Chebyshev filter and a 1700 MHz generalised Chebyshev filter showing excellent agreement with theory.     

DDC中的抽取滤波器设计及FPGA实现

本文介绍了在数字下变频（DDC）中的抽取滤波器系统设计方法和具体实现方案。采用CIC滤波器、HB滤波器、FIR滤波器三级级联的方式来降低采样率。通过实际验证，证明了设计的可行性。     

一种数字下变频抽取滤波器的设计

对一个针对数字下变频应用的抽取滤波器从设计指标到版图实现的设计过程进行了详细介绍.该抽取滤波器实现了20倍的降采样,由CIC滤波器、CIC补偿滤波器和半带滤波器三级依次串联而成.通过利用抽取滤波器的等价变换和多项分解性质,各滤波器级的硬件电路开销和运行功耗都得到了降低.     

大功率谐波吸收式滤波器设计

介绍了大功率谐波吸收式滤波器的实现电路，这些电路满足了信号分流的技术要求。文中给出了详细的工作原理和测试数据。     

Single-stage line-coupled ac/dc converter with high power factor and ripple-free input current

Single-stage line-coupled ac/dc converter with high power factor and ripple-free input current is proposed. The proposed power factor correction circuit can achieve high power factor and ripple-free input current using a coupled inductor. Experimental results for a 400?W converter at a constant switching frequency of 100?kHz are obtained to show the performance of the proposed converter.