Blends of poly(ethylene terephthalate) and poly(butylene terephthalate)

Commercial grade poly(ethylene terephthalate), (PET, intrinsic viscosity = 0.80 dL/g) and poly(butylene terephthalate), (PBT, intrinsic viscosity = 1.00 dL/g) were melt blended over the entire composition range using a counterrotating twin‐screw extruder. The mechanical, thermal, electrical, and rheological properties of the blends were studied. All of the blends showed higher impact properties than that of PET or PBT. The 50:50 blend composition exhibited the highest impact value. Other mechanical properties also showed similar trends for blends of this composition. The addition of PBT increased the processability of PET. Differential scanning calorimetry data showed the presence of both phases. For all blends, only a single glass‐transition temperature was observed. The melting characteristics of one phase were influenced by the presence of the other. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 75–82, 2005     

An infra-red study of the structure of oriented poly(ethylene terephthalate) fibres

Procedures have been developed for quantitative infra-red spectroscopic measurements on poly(ethylene terephthalate) fibres in conventional yarns. Following computer reconstruction methods already established for films, measurements of molecular orientation and trans/gauche conformer content have been carried out for a wide range of fibres produced by different processing routes. The trans bands can be separated into load-bearing and non-load-bearing conformations, where the former govern the modulus. It is also shown that a quantitative measure of amorphous orientation can be obtained from the infra-red measurements. While there are similarities between the development of overall molecular orientation and changes in molecular conformation for high wind-up speed yarns and drawn yarns produced from a low wind-up speed yarn, there are also major differences, which confirms previous work showing that these two classes of fibres are basically different in structure. These differences are shown by the relationships between the load-bearing trans conformations and the amorphous orientation with the overall orientation.     

Swollen-state polymerization of poly(ethylene terephthalate) in fibre form

The swollen-state polymerization of poly(ethylene terephthalate) in fibre form was performed in hydrogenated terphenyl as the swelling solvent. Ultra-high-molecular-weight poly(ethylene terephthalate) (CHMW-PET) fibre with an intrinsic viscosity of 3–4dl g⁻¹ (M_n = 2–3 × 10⁵) was obtained. The polymerization rate of as-spun PET fibres in the swollen state was greater than that of PET granules in the swollen state. It was clarified that the polymerization rate was related to the chain mobility of the starting materials. The chain mobility was influenced by various conditions, such as changing rigidity of the segments during copolymerization, the chain orientation of the starting fibre before swollen-state polymerization and the temperature of pretreatment with the solvent. Pretreatment with solvent before polymerization was effective in increasing the chain mobility. The relation between chain mobility and polymerization rate was examined by wide-angle X-ray diffraction, density, differential scanning calorimetry, solvent content and viscoelastic measurements. Undrawn UHMW-PET fibres could be drawn 10 times or more by the zone drawing technique in spite of their high crystallinity, and the drawn fibre showed high tensile strength (12 g d⁻¹) and high modulus (240 g d⁻¹).     

Synthesis and characterisation of copolyesters from poly(ethylene terephthalate) and poly(hexamethylene terephthalate)

Copolyesters containing poly(ethylene terephthalate) and poly(hexamethylene terephthalate) (PHT) were prepared by a melt condensation reaction. The copolymers were characterised by infrared spectroscopy and intrinsic viscosity measurements. The density of the copolyesters decreased with increasing percentage of PHT segments in the backbone. Glass transition temperatures (T_g). melting points (T_m) and crystallisation temperatures (T_c) were determined by differential scanning calorimetry. An increase in the percentage of PHT resulted in decrease in T_g, T_m and T_c. The as-prepared copolyesters were crystalline in nature and no exotherm indicative of cold crystallisation was observed. The relative thermal stability of the polymers was evaluated by dynamic thermogravimetry in a nitrogen atmosphere. An increase in percentage of PHT resulted in a decrease in initial decomposition temperature. The rate of crystallisation of the copolymers was studied by small angle light scattering. An increase in percentage of PHT resulted in an increase in the rate of crystallisation.     

Effect of poly(ethylene glycol) on the solid‐state polymerization of poly(ethylene terephthalate)

Poly(ethylene glycol) (PEG) and end‐capped poly(ethylene glycol) (poly(ethylene glycol) dimethyl ether (PEGDME)) of number average molecular weight 1000 g mol^?1 was melt blended with poly(ethylene terephthalate) (PET) oligomer. NMR, DSC and WAXS techniques characterized the structure and morphology of the blends. Both these samples show reduction in T_g and similar crystallization behavior. Solid‐state polymerization (SSP) was performed on these blend samples using Sb₂O₃ as catalyst under reduced pressure at temperatures below the melting point of the samples. Inherent viscosity data indicate that for the blend sample with PEG there is enhancement of SSP rate, while for the sample with PEGDME the SSP rate is suppressed. NMR data showed that PEG is incorporated into the PET chain, while PEGDME does not react with PET. Copyright © 2005 Society of Chemical Industry     

Morphology and crystallization of poly(ethylene terephthalate)

The melting behaviour and the morphology of poly(ethylene terephthalate) crystallized from the melt are reported. In general, dual or triple melting endotherms are seen, and single endotherms are seen when the samples are crystallized above 215°C for long times. The location of the uppermost endotherm was found to be constant below T_c = 230°C, and above that temperature the location depends on T_c. Therefore, we have shown that samples of PET which are crystallized above T_c = 230°C contain perfect crystals only; below T_c = 230°C, they contain perfect and imperfect crystals. Scanning electron microscopy showed that the perfect crystals are the dominant lamellae in the spherulitic structure, while the imperfect crystals are the subsidiary lamellae in the spherulitic structure, The amorphous regions are located between individual lamellae.     

PEN/PET共混物结晶行为研究

用差示扫描量热法(DSC)研究了不同共混比例PEN/PET共混物的熔体结晶行为,并进行了等温结晶动力学测定。结果表明:随着两种组分向中间比例(50/50)靠近,共混物的熔融温度越低,结晶速率也越慢。     

Characterization of the physical and molecular structure of thermally elongating poly(ethylene terephthalate) fibers

The mechanism of thermally induced elongation in poly(ethylene terephthalate) fiber spun at 3500 m min⁻¹ has been examined. This partially oriented fiber has a crystalline content of about 25% and a high degree of orientation. The effect of time and tension during heat treatment was examined, and it was found that yarns that were allowed to relax during an initial brief heat treatment at 130°C subsequently elongated by up to 5% during a long heat treatment at the same temperature. Yarns that were not allowed to relax during the brief heat treatment did not elongate on subsequent heating. The morphological and mechanical changes associated with these processes have been studied using differential scanning calorimetry, X-ray diffraction (XRD), birefringence measurement, microscopy, and tensile testing. A large increase in crystallinity was observed during the brief heat treatment, but a much smaller increase took place during the long heat treatment. XRD indicated that substantial crystal reorganization occurred during both heat treatments, but c-axis growth was most significant in those materials that elongated during long heat treatment. It is proposed that it is this c-axis growth, in conjunction with conversion of disordered amorphous material into oriented crystalline material, that is responsible for the observed elongation. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 989–995, 1997     

Characterization of surface‐modified poly(ethylene terephthalate) fibres by inverse gas chromatography

The effect of surface cleanliness on the alkaline hydrolysis of poly(ethylene terephthalate) fibres was investigated using inverse gas chromatography (IGC) in conjunction with mass loss measurements and electron microscopy. The sizing agent was removed from the fibre surface by two methods: soxhlet cleaning in acetone and washing in an aqueous solution of a non‐ionic detergent. Alkaline hydrolysis was carried out using two concentrations of aqueous sodium hydroxide, 1% and 10% by mass. The measurement of the specific retention volume of undecane and the heat of adsorption using IGC indicated that the acetone cleaned samples were essentially surface contaminant free, while partial contamination of the surface by the sizing agent remained in the detergent cleaned samples. The presence of sizing agent significantly altered the degree of hydrolysis and the surface topography. The increasing values of the heat of adsorption indicated that significant surface hydrolysis increased the surface crystallinity. © 2000 Society of Chemical Industry     

Sequence analysis of poly(ethylene terephthalate)/poly(butylene terephthalate) copolymer prepared by ester-interchange reactions

The molecular structure of the copolyester formed through the interchange reaction in poly(ethylene terephthalate)/poly(butylene terephthalate) blends was investigated with ¹³C-NMR spectroscopy. The molar fractions of heterolinkage triads in the copolyesters were lower than the values calculated by Bernoullian statistics; this indicates that the sequence of heterolinkages was far from a random distribution at the initial stage of the interchange reaction. However, the randomness increased and the number-average sequence length decreased with reaction time. The solubility of the blend decreased with increasing sequence length, resulting from the formation of block copolymers with long sequence lengths at the initial stage of the interchange reaction. The solubility of the copolyester formed by a dibutyltin dilaurate (DBTDL)-catalyzed reaction was higher than that of the copolyester formed by a titanium tetrabutoxide-catalyzed reaction; this is related to the fact that alcoholysis prevailed in the DBTDL-catalyzed reaction. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 159–168, 2001     

聚(对苯二甲酸乙二醇酯-co-对苯二甲酸异山梨醇酯)等温结晶行为研究

以对苯二甲酸(PTA)、乙二醇(EG)、异山梨醇(ISB)为原料,通过直接熔融缩聚法合成聚(对苯二甲酸乙二醇酯-co-对苯二甲酸异山梨醇酯)(PEIT)共聚酯。利用差示扫描量热法(DSC)研究了共聚酯的结晶行为,采用Avrami方程分析了共聚酯的等温结晶动力学。结果表明,PEIT共聚酯结晶行为受共聚组成和结晶温度影响。随着ISB用量的增加或结晶温度的降低,共聚酯半结晶周期t1/2增加、结晶速率变慢;ISB摩尔分数超过20%,共聚酯无法结晶。     

Surface modification of poly(ethylene terephthalate) film by coating with poly(ethylene glycol)‐grafted polystyrene

The poly(ethylene glycol) (PEG)‐grafted styrene (St) copolymer, which was formed as a nanosphere, was used as an agent to modify the surface of poly(ethylene terephthalate) (PET) film. The graft copolymer was dissolved into chloroform and coated onto the PET film by dip–coating method. The coated amount depends on the content ratios of PEG and St, the solution concentration, and the coating cycles. The graft copolymers having a low molecular weight of PEG‐ or St‐rich content was fairly stable on washing in sodium dodecyl sulfate (SDS) aqueous solution. It was confirmed that the PET surface easily altered its surface property by the coating of the graft copolymers. The contact angles of the films coated with the graft copolymers were very high (ca. 105–120°). The coated film has good antistatic electric property, which agreed with PEG content. The best condition of coating is a one‐cycle coating of 1% (w/v) graft copolymer solution. The coated surface had water‐repellency and antistatic electric property at the same time. The graft copolymer consisted of a PEG macromonomer; St was successfully coated onto PET surfaces, and the desirable properties of both of PEG macromonomer and PSt were exhibited as a novel function of the coated PE film. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1524–1530, 1999     

Modeling of solid-state polymerization of poly(ethylene terephthalate)

A mathematical model for solid-state polymerization of poly(ethylene terephthalate) was developed. The effects of temperature and chain entanglement on chain mobility were considered to estimate the rate constants of chemical reactions. The diffusivities of volatile byproducts could be determined using the free volume theory.^13,14 The model predictions were validated with experimental data reported in the literature. In addition, assuming that the concentration profiles of volatile byproducts in spherical particles are described by a sinusoidal function, the mass transfer rate of the byproducts at a given time could be derived as an ordinary differential equation that can be easily treated. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68:837–846, 1998     

Volatile products of poly(ethylene terephthalate) thermal degradation in nitrogen atmosphere

Thermal degradation of PET was studied in a nitrogen atmosphere at 200–700°C. The experiments were carried out in a tubular furnace under isothermal conditions. The volatile substances evolved from PET were identified and quantified. Weight losses of PET during the thermal degradation in different temperatures were determined. The results are presented on plots as a function of the degradation temperature. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1894–1901, 2000     

Microstructure and crystallization of melt‐mixed poly(ethylene terephthalate)/poly(ethylene isophthalate) blends

Physical blends of poly(ethylene terephthalate) (PET) and poly(ethylene isophthalate) (PEI), abbreviated PET/PEI (80/20) blends, and of PET and a random poly(ethylene terephthalate‐co‐isophthalate) copolymer containing 40% ethylene isophthalate (PET₆₀I₄₀), abbreviated PET/PET₆₀I₄₀ (50/50) blends, were melt‐mixed at 270°C for different reactive blending times to give a series of copolymers containing 20 mol % of ethylene isophthalic units with different degrees of randomness. ¹³C‐NMR spectroscopy precisely determined the microstructure of the blends. The thermal and mechanical properties of the blends were evaluated by DSC and tensile assays, and the obtained results were compared with those obtained for PET and a statistically random PETI copolymer with the same composition. The microstructure of the blends gradually changed from a physical blend into a block copolymer, and finally into a random copolymer with the advance of transreaction time. The melting temperature and enthalpy of the blends decreased with the progress of melt‐mixing. Isothermal crystallization studies carried out on molten samples revealed the same trend for the crystallization rate. The effect of reaction time on crystallizability was more pronounced in the case of the PET/PET₆₀I₄₀ (50/50) blends. The Young's modulus of the melt‐mixed blends was comparable to that of PET, whereas the maximum tensile stress decreased with respect to that of PET. All blend samples showed a noticeable brittleness. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3076–3086, 2003     

Transesterification in poly(ethylene terephthalate) and poly(ethylene naphthalate 2,6-dicarboxylate) blends: model compounds study

Kinetics of transesterification reaction in poly(ethylene terephthalate)-poly(ethylene naphthalate 2,6-dicarboxylate), PET-PEN, blends resulting from melt processing was simulated using model compounds of ethylene dibenzoate (BEB) and ethylene dinaphthoate (NEN). The exchange reaction between BEB and NEN was followed by ¹H NMR spectroscopy using signals from the aliphatic protons of ethylene glycol moieties at 4.66 and 4.78 ppm, respectively. The first-order kinetics was established under pseudo-first-order conditions for both reactants. Thus, the overall transesterification reaction was second order reversible. The reversibility was confirmed experimentally by heating a mixed sequence of 1-benzoate 2-naphthoate ethylene (BEN) under similar conditions. Both forward reaction of the equimolar amounts of the reagents and reverse reaction came to equilibrium at the same molar ratio of the reactants and reaction products of roughly 0.25:0.50:0.25 for BEB, BEN, and NEN, respectively. The rate equation for the transesterification reaction in the model system was modified using half-concentration of BEN, which is the only effective in the intermolecular exchange. Direct ester-ester exchange was deduced as a prevailing mechanism for the transesterification reaction under the conditions studied, and the values of equilibrium and rate constants, as well as other basic thermodynamic and kinetic parameters were determined. The use of Zn(OAc)₂ as a catalyst resulted in a significant decrease in the activation enthalpy of transesterification, which might be due to the partial switch of the reaction mechanism from primarily pseudo-homolytic to more heterolytic where Zn^II acts as a Lewis base which binds to the ester carbonyl oxygen.     

Wide angle X-ray diffraction study of the solid-phase chlorinated poly(ethylene)

Series of samples of solid-phase chlorinated poly(ethylene) (CPE) have been studied by using both the methods of wide angle X-ray diffraction analysis (WAXD) and optical microscopy. Some basic crystallographic characteristics of CPE of 1.27 to 56.09 chlorine content were determined. The increase of chlorine content in the product was found to result in a relatively weak increase of the parameter a for melt-crystallized samples, whereas the parameter c values of the cold-sintered samples decreased. The crystallite sizes in the [110] and [020] directions for the melt-crystallized samples increased to the higher extent up to, approximately, 10% chlorine content, as compared to those of CPE available as powder or pellets. The degree of crystallinity was reduced as the chlorine content increased, but, even with 56% chlorine introduced, the polymer had a crystalline-amorphous structure. The optical micrographs showed that, up to 40% Cl, CPE had crystalline structure dominated by the formation of spherolites whereas, at higher chlorine content, structures of the lower order of crystallinity were formed. These observed changes were predominantly determined by the defects in the PE crystals, resulting from the inclusion of a certain fraction of chloromethylene groups therein.     

Biodegradability of poly(ethylene terephthalate) copolymers with poly(ethylene glycol)s and poly(tetramethylene glycol)

Poly(ethylene terephthalate) copolymers were prepared by melt polycondensation of dimethyl terephthalate and excess ethylene glycol with 10–40mol% (in feed) of poly(ethylene glycol) (E) and poly(tetramethylene glycol) (B), with molecular weight (MW) of E and B 200–7500 and 1000, respectively. The reduced specific viscosity of copolymers increased with increasing MW and content of polyglycol comonomer. The temperature of melting (T_m), cold crystallization and glass transition (T_g) decreased with the copolymerization. T_m depression of copolymers suggested that the E series copolymers are the block type at higher content of the comonomer. T_g was decreased below room temperature by the copolymerization, which affected the crystallinity and the density of copolymer films. Water absorption increased with increasing content of comonomer, and the increase was much higher for E1000 series films than B1000 series films. The biodegradability was estimated by weight loss of copolymer films in buffer solution with and without a lipase at 37°C. The weight loss was enhanced a little by the presence of a lipase, and increased abruptly at higher comonomer content, which was correlated to the water absorption and the concentration of ester linkages between PET and PEG segments. The weight loss of B series films was much lower than that of E series films. The abrupt increase of the weight loss by alkaline hydrolysis is almost consistent with that by biodegradation.     

Aspects of the chemistry of poly(ethylene terephthalate): 5. Polymerization of bis(hydroxyethyl)terephthalate by various metallic catalysts

Bis(hydroxyethyl)terephthalate (BHET) was polymerized to poly(ethylene terephthalate) (PET) in the presence of various metallic catalysts. The influence of the nature and concentration of these catalysts on the rate of polymerization has been investigated. The effect of the reaction temperature has also been studied. The order of decreasing catalytic influence of various metal ions, on the polymerization of BHET was found to be: Ti>Sn>Mn>Zn>Pb>No.     

Modification of poly(ethylene terephthalate) surface with attached dextran macromolecules

BACKGROUND: Peroxidation of a poly(ethylene terephthalate) (PET) surface clears the path to the formation of biospecific polymeric layers on it. The goal of this work was the modification of a PET surface with oligoperoxides with further grafting of dextran macromolecules to this peroxidated surface. RESULTS: Novel oligoperoxides with a good affinity to PET were synthesized. They are capable of attaching to the PET surface, due to the decomposition of peroxide groups via the formation of free radicals. The alterations in surface energy and its components as a result of surface modification as well as changes in topography of the PET surface were determined. The degree of modification of the PET surface can reach 68% and depends on the following: the method of oligoperoxide and dextran deposition; the concentration of both oligoperoxide and dextran in the initial solution; and the temperature at which the modification is carried out. CONCLUSION: A new method of PET surface activation has been developed. The attachment of dextran macromolecules to modified PET surfaces is confirmed. Copyright © 2009 Society of Chemical Industry