Culturable and Total Fungi in Dust Accumulated in Air Ducts in Single-Family Houses

Abstract Fungal spore content in dust accumulated in air ducts was investigated in 24 mechanically ventilated single-family houses of which 15 had also a central air heating system. Dust was collected from the ducts simultaneously with cleaning of the ventilation systems. Besides spore concentrations and flora of culturable fungi, total fungal spore concentrations were determined in dust samples by the aqueous two-phase technique and spore counting with epifluorescence microscopy. Culturable spore concentrations in the dust varied from 10⁴ to 10⁷ CFU/g and total spore concentrations from 107 to 108 spores/g. Total spore concentrations in the duct dust were significantly higher in the air heated houses than in the other mechanically ventilated houses. The difference resulted mainly from a higher proportion of recirculation air and a higher age of the air heated houses. Cladosporium, Penicillium, Aspergillus and yeasts consisted of >90% of fungal flora in the dust. Although total spore concentrations were at the same level both in the exhaust and in the supply ducts in both types of house, culturable fungal spore concentrations were slightly higher in the exhaust ducts than in the supply ducts. The proportion of culturable spores was <5% of total spores in dust accumulated in the ducts.     

Levels of microbial agents in floor dust during remediation of a water-damaged office building

We examined the effects of remediation on loads of culturable fungi in floor dust collected from a large water-damaged office building during four cross-sectional surveys (2002, 2004, 2005, and 2007, respectively). We created a binary remediation variable for each year for each sampled workstation using information on remediation associated with water damage obtained from building management and used generalized linear mixed-effects models. We found significantly lower levels of culturable total and hydrophilic fungi at remediated workstations than at non-remediated workstations in 2004 and 2005 after completion of major remediation. The remediation effect, however, disappeared in 2007. The fraction of hydrophilic to total fungal concentrations was lowest in 2004, increased in 2005, and was highest in 2007. Our results indicate that the 2003 remediation lowered dust indices of dampness temporarily, but remediation was incomplete, consistent with a building assessment report of water infiltration. This study demonstrates the utility of longitudinal evaluation of microbial indices during remediation of water damage in this building, in which elimination of sources of moisture was not fully addressed. Our findings indicate that the fraction of hydrophilic fungi derived from concentrations of fungal species may be a useful index for assessing the long-term effectiveness of remediation. PRACTICAL IMPLICATIONS: This study demonstrates the utility of longitudinal evaluation of microbial indices during remediation of water damage in this building, in which elimination of sources of moisture was incomplete. Our findings indicate that the fraction of hydrophilic fungi derived from concentrations of fungal species may be a useful index for assessing the long-term effectiveness of remediation.     

Effect of relative humidity on the aerosolization and total inflammatory potential of fungal particles from dust‐inoculated gypsum boards

The aim of this study was to investigate the effect of relative humidity (RH) on the aerosolization and total inflammatory potential (TIP) of microbial particles released from gypsum boards inoculated with dust samples from homes. After microbial colonization, the gypsum boards were incubated at either high or low RH. The aerosolized particles (0.54–19.8 μm), culturable fungi, β‐glucan and the TIP of the aerosolized particles were quantified. Despite the colonization of several fungal groups, Penicillium dominated the aerosolized fraction. Higher emission rates of particles and culturable fungi were found from low RH compared with high RH in both the inhalable and particulate matter <1 μm (PM₁) fractions, and the TIP was accordingly higher. However, for the aerosolized fractions, the TIP or concentration β‐glucan relative to the number of fungi or particles present was higher from high RH compared with low RH. Despite the low number of culturable fungi in PM₁, this fraction showed a high TIP, and the concentration of β‐glucan correlated strongly with the TIP of this fraction. The individual particles of the aerosolized PM₁ fraction were more inflammatory than the larger particles of the inhalable fraction, and β‐glucan may be an important contributor to the inflammatory potential of the aerosolized particles.     

Quantitative profiling of built environment bacterial and fungal communities reveals dynamic material dependent growth patterns and microbial interactions

Indoor microbial communities vary in composition and diversity depending on material type, moisture levels, and occupancy. In this study, we integrated bacterial cell counting, fungal biomass estimation, and fluorescence-assisted cell sorting (FACS) with amplicon sequencing of bacterial (16S rRNA) and fungal (ITS) communities to investigate the influence of wetting on medium density fiberboard (MDF) and gypsum wallboard. Surface samples were collected longitudinally from wetted materials maintained at high relative humidity (~95%). Bacterial and fungal growth patterns were strongly time-dependent and material-specific. Fungal growth phenotypes differed between materials: spores dominated MDF surfaces while fungi transitioned from spores to hyphae on gypsum. FACS confirmed that most of the bacterial cells were intact (viable) on both materials over the course of the study. Integrated cell count and biomass data (quantitative profiling) revealed that small changes in relative abundance often resulted from large changes in absolute abundance, while negative correlations in relative abundances were explained by rapid growth of only one group of bacteria or fungi. Comparisons of bacterial-bacterial and fungal-bacterial networks suggested a top-down control of fungi on bacterial growth, possibly via antibiotic production. In conclusion, quantitative profiling provides novel insights into microbial growth dynamics on building materials with potential implications for human health.     

Residential culturable fungi, (1‐3, 1‐6)‐β‐d‐glucan,and ergosterol concentrations in dust are not associated with asthma,rhinitis, or eczema diagnoses in children

Qualitative reporting of home indoor moisture problems predicts respiratory diseases. However, causal agents underlying such qualitative markers remain unknown. In the homes of 198 multiple allergic case children and 202 controls in Sweden, we cultivated culturable fungi by directly plating dust, and quantified (1‐3, 1‐6)‐β‐d ‐glucan and ergosterol in dust samples from the child's bedroom. We examined the relationship between these fungal agents and degree of parent or inspector‐reported home indoor dampness, and microbiological laboratory's mold index. We also compared the concentrations of these agents between multiple allergic cases and healthy controls, as well as IgE‐sensitization among cases. The concentrations of culturable fungal agents were comparable between houses with parent and inspector‐reported mold issues and those without. There were no differences in concentrations of the individual or the total summed culturable fungi, (1‐3, 1‐6)‐β‐d ‐glucan, and ergosterol between the controls and the multiple allergic case children, or individual diagnosis of asthma, rhinitis, or eczema. Culturable fungi, (1‐3, 1‐6)‐β‐d ‐glucan, and ergosterol in dust were not associated with qualitative markers of indoor dampness or mold or indoor humidity. Furthermore, these agents in dust samples were not associated with any health outcomes in the children.     

Airborne viable, non-viable, and allergenic fungi in a rural agricultural area of India: a 2-year study at five outdoor sampling stations

The information on airborne allergenic fungal flora in rural agricultural areas is largely lacking. Adequate information is not available to the bioaerosol researchers regarding the choice of single versus multiple sampling stations for the monitoring of both viable and non-viable airborne fungi. There is no long-term study estimating the ratios of viable and non-viable fungi in the air and earlier studies did not focus on the fractions of airborne allergenic fungi with respect to the total airborne fungal load. To fill these knowledge gaps, volumetric paired assessments of airborne viable and non-viable fungi were performed in five outdoor sampling stations during two consecutive years in a rural agricultural area of India. Samples were collected at 10-day intervals by the Burkard Personal Slide Sampler and the Andersen Two-Stage Viable Sampler. The data on the concentrations of total and individual fungal types from five stations and 2 different years were analyzed and compared by statistical methods. The allergenicity of the prevalent airborne viable fungi was estimated by the skin-prick tests of >100 rural allergy patients using the antigenic fungal extracts from isolates collected with the Andersen sampler. The ranges of total fungal spore concentration were 82-2365 spores per cubic meter of air (spores/m3) in the first sampling year and 156-2022 spores/m3 in the second sampling year. The concentration ranges of viable fungi were 72-1796 colony-forming units per cubic meter of air (CFU/m3) in the first sampling year and 155-1256 CFU/m3 in the second sampling year. No statistically significant difference was observed between the total spore data of the 2 years, however, the data between five stations showed a significant difference (P<0.0001). No statistically significant difference existed between stations and years with respect to the concentration of viable fungi. When the data of individual allergenic fungal concentrations were compared between stations and years, no statistically significant difference was observed in all cases except for Aspergillus japonicus and Rhizopus nigricans, which showed significant difference in case of stations and years, respectively. The ratios between the total fungal spores collected by the Burkard sampler and the viable fungi collected by the Andersen sampler from all sampling stations ranged between 0.29 and 7.61. The antigenic extracts of eight prevalent viable airborne fungi (A. flavus, A. japonicus, A. fumigatus, Alternaria alternata, Cladosporium cladosporioides, Curvularia pallescens, Fusarium roseum, and R. nigricans) demonstrated >60% positive reactions in the skin prick test. These selected allergenic fungi collectively represented 31.7-63.2% of the total airborne viable fungi in different stations. The study concluded that: (i) a rich fungal airspora existed in the rural study area, (ii) to achieve representative information on the total airborne fungal spores of an area, the monitoring in multiple sampling stations is preferable over a single sampling station; for viable fungi, however, one station can be considered, (iii) the percentage of airborne fungal viability is higher in rural agricultural areas, and (iv) approximately 52% of the viable airborne fungi in the rural study area were allergenic.     

Changes in profiles of airborne fungi in flooded homes in southern Taiwan after Typhoon Morakot

In August 2009, the historic Typhoon Morakot brought extreme rainfall and resulted in flooding which spread throughout southern Taiwan. This study compared the difference between fungal concentrations before and after the disaster in selected homes of the Tainan metropolitan area, which were hit hardest by the catastrophe. A group of 83 households available from a prior cohort established with random sampling out of a regional population in southern Taiwan was contacted successfully by telephone. Twenty-five of these reported to have suffered from floods of various degrees at this time. Around 2 weeks after the event, at which time most of the remedial process had been completed by self-efforts and public health endeavours, 14 of these 25 (56%) agreed to participate in measurements of the airborne microbial concentrations. The averages (standard deviation) of the total culturable fungal concentrations in children's bedrooms and flooded rooms were 18,181 (25,854) colony-forming units per cubic metre (CFU/m³) and 13,440 (11,033) CFU/m³, respectively. The airborne fungal spore levels in the 2 above-mentioned indoor sites were 221,536 (169,640) spores/m³ and 201,582 (137,091) spores/m³, respectively. The average indoor/outdoor ratios in the children's bedrooms were 4.2 for culturable fungi and 1.4 for fungal spores. These values were higher than the respective values measured in the same homes during the previous year: 1.1 and 0.6. In terms of the specific fungal profile, the percentages of Aspergillus spp. increased significantly in both the indoor and outdoor environments after the event. To this date, this study is among the limited research that has been conducted to quantitatively demonstrate that fungal manifestation is likely to persist in flooded homes even after seemingly robust remedial measures have been put into place. Studies to examine the potential health implications and effectiveness of better remedial technology remain much needed.     

Assessment of home environments with a fungal index using hydrophilic and xerophilic fungi as biologic sensors

Previously, the author proposed a 'fungal index' that quantifies the capacity for fungal growth in a test environment where a device (fungal detector) encapsulating spores of a xerophilic sensor fungus Eurotium herbariorum was placed. It was also found that an extremely xerophilic fungus, Aspergillus penicillioides, was suitable as a sensor fungus at sites with lower relative humidity (RH). In this report, the hydrophilic fungus Alternaria alternata was added to sensor fungi for the determination of the index in extremely humid environments. Measurements of the index and observations of the formation of spores by the sensor fungi were made in stable climates in moisture chambers, under natural conditions in homes, and in bathrooms prepared in an artificial climate chamber. Higher index values and earlier sporulation were obtained at higher RH in stable climates. The hydrophilic Alt. alternata showed the greatest response at 100% and 97.3% RH, the moderately xerophilic Eur. herbariorum, at 94%, 84%, and 75% RH, and the extremely xerophilic Asp. penicillioides, at 71% RH. In homes, the hydrophilic fungus was most active in water-usage areas, and the xerophilic fungi were most active in non-water-usage areas. Sporulation was observed on sensor fungi in fungal detectors placed in rooms where the index exceeded 18 ru/week after one-month exposure. Sites where the index exceeded 18 ru/week were referred to as damp, where fungal contamination seems to be unavoidable. Evaluations of ventilation systems in bathrooms with extremely humid climates showed typical examples of a countermeasure to fungal contamination. PRACTICAL IMPLICATIONS: The purpose of this study is to establish a fungal index applicable in home environments with extremely high to relatively low relative humidity climates. The sensor fungus that showed the greatest response in a fungal detector (a device encapsulating spores of sensor fungi) served as not only a quantitative but also a qualitative indicator of the environment tested, indicating the type of fungi that would contaminate the site. A fungal index would be a good tool for detecting dampness that induces fungal contamination, which has adverse effects on human health. Evaluations of indoor climates would provide information useful to building owners, builders, designers, advisers, medical practitioners, and so on. Selection of the most suitable insulation systems in various buildings under different climates or evaluations of the drying process in water-damaged buildings could also be possible using fungal detectors and measurements of fungal indices.     

Relationship between indoor and outdoor bio-aerosols collected with a button inhalable aerosol sampler in urban homes

This field study investigated the relationship between indoor and outdoor concentrations of airborne actinomycetes, fungal spores, and pollen. Air samples were collected for 24 h with a button inhalable aerosol sampler inside and outside of six single-family homes located in the Cincinnati area (overall, 15 pairs of samples were taken in each home). The measurements were conducted during three seasons - spring and fall 2004, and winter 2005. The concentration of culturable actinomycetes was mostly below the detection limit. The median indoor/outdoor ratio (I/O) for actinomycetes was the highest: 2.857. The indoor of fungal and pollen concentrations followed the outdoor concentrations while indoor levels were mostly lower than the outdoor ones. The I/O ratio of total fungal spores (median=0.345) in six homes was greater than that of pollen grains (median=0.025). The low I/O ratios obtained for pollen during the peak ambient pollination season (spring) suggest that only a small fraction penetrated from outdoor to indoor environment. This is attributed to the larger size of pollen grains. Higher indoor concentration levels and variability in the I/O ratio observed for airborne fungi may be associated with indoor sources and/or higher outdoor-to-indoor penetration of fungal spores compared to pollen grains. Practical Implication This study addresses the relationship between indoor and outdoor concentrations of three different types of bio-aerosols, namely actinomycetes, fungal spores, and pollen grains. The results show that actinomycetes are rare in indoor and outdoor air in Midwest, USA. Exposure to pollen occurs mainly in the outdoor air even during peak pollen season. Unexpectedly high fungal spore concentrations were measured outdoors during winter. The presented pilot database on the inhalable levels of indoor and outdoor bio-aerosols can help apportion and better characterize the inhalation exposure to these bio-aerosols. Furthermore, the data can be incorporated into existing models to quantify the penetration of biological particles into indoor environments from outdoors.     

Susceptibility of green and conventional building materials to microbial growth

Green building materials are becoming more popular. However, little is known about their ability to support or limit microbial growth. The growth of fungi was evaluated on five building materials. Two green, two conventional building materials and wood as a positive control were selected. The materials were inoculated with Aspergillus versicolor, Cladosporium cladosporioides and Penicillium brevicompactum, in the absence and presence of house dust. Microbial growth was assessed at four different time points by cultivation and determining fungal biomass using the N‐acetylhexosaminidase (NAHA) enzyme assay. No clear differences were seen between green and conventional building materials in their susceptibility to support microbial growth. The presence of dust, an external source of nutrients, promoted growth of all the fungal species similarly on green and conventional materials. The results also showed a correlation coefficient ranging from 0.81 to 0.88 between NAHA activity and culturable counts. The results suggest that the growth of microbes on a material surface depends on the availability of organic matter rather than the classification of the material as green or conventional. NAHA activity and culturability correlated well indicating that the two methods used in the experiments gave similar trends for the growth of fungi on material surfaces.     

Characterizing Mold Problem Buildings – Concentrations And Flora Of Viable Fungi

The purpose of this study was to characterize mold problem buildings by determining concentrations and flora of viable fungi. The composition and concentrations of fungal flora in mold problem (n = 9) and reference buildings (n = 9) were determined by means of four different sampling methods: six-stage impactor (Andersen sampler), sedimentation plate, surface and house dust samples. Samples were taken in the fall and in the winter, and the concentrations and flora in mold problem buildings were compared with those of matched reference buildings. The differences between mold problem and reference buildings were most clearly seen with the impactor samples. The total concentrations of airborne fungi were higher in moldy buildings. In addition, the concentrations of the genera Aspergillus and Oidiodendron in the fall and the concentrations of Aspergillus and Penicillium in the winter were higher in mold problem than in reference buildings. In the winter, certain fungal genera (Stachybotrys, Acremonium, Oedocephalum and Botryosporium) were detected only in the problem buildings in impactor samples. These results indicate that there may be an unusual composition of fungal flora in mold problem buildings. The results of the sedimentation plate samples showed a trend similar to that of impactor samples in the winter. In addition, the results of surface samples supported the data on the fungal flora in the winter-time air samples. The house dust samples did not reveal any differences between mold problem and matched reference buildings.     

Biodeterioration of sandstone under the influence of different humidity levels in laboratory conditions

Excessive moisture in building materials supports microbial growth. It has been referred that relative humidity more than 55% promotes the microbial growth. To test the effect of different relative humidity tropical chamber test was set up at 52%, 76%, 85% and 96% RH and maximum diversity of fungi was found at 85% and 96% RH. Two fungi Aspergillus sydowi and Aspergillus flavipes were present throughout the course of study from moderate to highly abundant form. It was observed that Fusarium moniliforme, Cephalosporium acremonium, Papulospora sp. proliferated at higher relative humidity (i.e. at 85% and 96.6% RH) and Fusarium roseum, Fusarium oxysporum only at 96% RH level. The relative humidity level lower than 62%, i.e. at 52% level exhibited no fungal growth on sandstone surface during two-year observations. During the study pattern it was noticed that diversity decreased gradually and dominance of particular species increased with the time factor. Analysis of sandstone after fungal colonization by X-ray diffraction and SEM showed the formation of newly formed biomineral.     

Culturable airborne fungi in outdoor environments in Beijing, China

Airborne fungi are being proposed as a cause of adverse health effects. They may adversely affect human health through allergy, infection, and toxicity. Moreover, they have a great influence on urban air quality in Beijing. In this study, a systematical survey on the culturable airborne fungi was carried out for 1 year in Beijing urban area. Fungal samples were collected for 3 min, three times each day, and continued for three consecutive days of each month with FA-1 sampler from three sampling sites. Results showed that the culturable fungal concentrations ranged from 24 CFU (Colony forming units) /m3 to 13960 CFU/m3, and the mean and median was 1165 CFU/m3 and 710 CFU/m3, respectively. Fungal concentrations in the greener area around the Research Center for Eco-Environmental Sciences (RCEES) and Beijing Botanical Garden (BBG) were significantly higher than in the densely urban and highly trafficked area of Xizhimen (XZM) (***P<0.001), but no significant difference was found between RCEES and BBG (P>0.05). The variation of fungal concentrations in different seasons was significant in RCEES and BBG, where the concentrations were higher in Summer and Autumn, and lower in Spring and Winter. However, there were no significant differences in fungal concentrations between the Spring and the Winter for three sampling sites (P>0.05). Fourteen genera, including 40 species of culturable fungi, were identified in this study. Penicillium, with the most abundant species, which comprised more than 50% of the total isolated fungal species. Cladosporium were the most dominant fungal group, and contributed to more than one third of the total fungal concentration, followed by non-sporing isolates, Alternaria, Pencillium and Asperigillus. The concentration percentage of Cladosporium was significantly higher in RCEES than in XZM (*P<0.05), and the concentration percentages of Penicillium (**P<0.01) and Aspergillus (*P<0.05) were higher in XZM than in RCEES and in BBG. For other groups' concentration percentages, no significant differences were observed among the sampling sites. The distribution pattern of airborne fungi presented log-normal distribution. The highest proportion of culturable fungi was detected in stage 4 (2.0-3.5 microm), and the lowest was in stage 6 (<1.0 microm).     

Microbial growth in building material samples and occupants’ health in severely moisture‐damaged homes

There is no commonly approved approach to detect and quantify the health‐relevant microbial exposure in moisture‐damaged buildings. In 39 single‐family homes with severe moisture damage, we studied whether concentrations of viable microbes in building material samples are associated with health among 71 adults and 68 children, and assessed with symptoms questionnaires, exhaled NO, and peak expiratory flow (PEF) variability. Symptoms were grouped into three scores: upper respiratory symptoms, lower respiratory symptoms, and general symptoms. The homes were divided into three groups based on viable counts of fungi, actinomycetes, and total bacteria cultivated from building material samples. Highest group of actinomycete counts was associated with more general symptoms, worse perceived health, and higher daily PEF variability (aOR 12.51; 1.10‐141.90 as compared to the lowest group) among adults, and with an increase in lower respiratory symptoms in children, but the confidence intervals were wide. We observed significant associations of fungal counts and total microbial score with worse perceived health in adults. No associations with exhaled NO were observed.     

Determination of fungal spore release from wet building materials

The release and transport of fungal spores from water-damaged building materials is a key factor for understanding the exposure to particles of fungal origin as a possible cause of adverse health effects associated to growth of fungi indoors. In this study, the release of spores from nine species of typical indoor fungi has been measured under controlled conditions. The fungi were cultivated for a period of 4-6 weeks on sterilized wet wallpapered gypsum boards at a relative humidity (RH) of approximately 97%. A specially designed small chamber (P-FLEC) was placed on the gypsum board. The release of fungal spores was induced by well-defined jets of air impacting from rotating nozzles. The spores and other particles released from the surface were transported by the air flowing from the chamber through a top outlet to a particle counter and sizer. For two of the fungi (Penicillium chrysogenum and Trichoderma harzianum), the number of spores produced on the gypsum board and subsequently released was quantified. Also the relationship between air velocities from 0.3 to 3 m/s over the surface and spore release has been measured. The method was found to give very reproducible results for each fungal isolate, whereas the spore release is very different for different fungi under identical conditions. Also, the relationship between air velocity and spore release depends on the fungus. For some fungi a significant number of particles smaller than the spore size were released. The method applied in the study may also be useful for field studies and for generation of spores for exposure studies.     

Observational scores of dampness and mold associated with measurements of microbial agents and moisture in three public schools

We examined associations between observational dampness scores and measurements of microbial agents and moisture in three public schools. A dampness score was created for each room from 4‐point‐scale scores (0–3) of water damage, water stains, visible mold, moldy odor, and wetness for each of 8 room components (ceiling, walls, windows, floor, ventilation, furniture, floor trench, and pipes), when present. We created mixed microbial exposure indices (MMEIs) for each of 121 rooms by summing decile ranks of 8 analytes (total culturable fungi; total, Gram‐negative, and Gram‐positive culturable bacteria; ergosterol; (1→3)‐β‐D‐glucan; muramic acid; and endotoxin) in floor dust. We found significant (P ≤ 0.01) linear associations between the dampness score and culturable bacteria (total, Gram‐positive, and Gram‐negative) and the MMEIs. Rooms with dampness scores greater than 0.25 (median) had significantly (P < 0.05) higher levels of most microbial agents, MMEIs, and relative moisture content than those with lower scores (≤0.25). Rooms with reported recent water leaks had significantly (P < 0.05) higher dampness scores than those with historical or no reported water leaks. This study suggests that observational assessment of dampness and mold using a standardized form may be valuable for identifying and documenting water damage and associated microbial contamination.     

Fungal extracellular polysaccharides, beta (1-->3)-glucans and culturable fungi in repeated sampling of house dust

Fungal exposure inside homes has been associated with adverse respiratory symptoms in children and adults. While fungal assessment has traditionally relied upon questionnaires, fungal growth on culture plates and spore counts, new immunoassays for extracellular polysaccharides (EPS) and beta (1-->3)-glucans have enabled quantitation of fungal agents in house dust in a more timely and cost-effective manner, possibly providing a better measure of fungal exposure. We investigated associations among measurements of EPS, beta (1-->3)-glucans and culturable fungi obtained from 23 Dutch homes. From each home, dust samples were vacuumed from the living room floor twice during the Fall, Winter and Spring seasons for a total of six collections (every 6 weeks from October 1997 to May 1998). Samples were sieved and fine dust was analyzed for EPS from Aspergillus and Penicillium spp. combined, beta (1-->3)-glucans and culturable fungi. EPS was positively associated with glucan; an increase from the 25th to the 75th percentile of glucan concentration was associated with a 1.6-fold increase in EPS concentration (95% CI = 1.3 to 2.0; p < 0.01). The most significant variables associated with EPS and glucan concentrations were the surface type that was vacuumed and the concentration of total culturable fungi (in colony forming units (CFU)/g dust), with an increase in CFU/g from the 25th to the 75th percentile associated with a 1.3 (1.1-1.6)-fold increase in glucan and a 1.7 (1.3-2.2)-fold increase in EPS concentrations. In addition, the within-home variation of EPS levels were smaller than those between homes (25,646 U/g vs. 50,635 U/g), whereas the variation of glucan levels was similar within and between homes (1,300 vs. 1,205 micrograms/g). These positive associations suggest that house dust concentrations of beta (1-->3)-glucan, and particularly those of EPS, are good markers for the overall levels of fungal concentrations in floor dust which is a surrogate for estimating airborne fungal exposure.     

竹木复合地板变形有限元模拟

以表层为竹材、芯层为杉木拼板、背层为杨木单板的竹木复合地板为对象,利用ANSYS有限元软件,采用湿热类比法模拟表层和芯层厚度不同的竹木复合地板在干燥环境中的含水率变化,然后进行热结构耦合分析,研究由含水率变化引起的竹木复合地板的翘曲变形.结果表明:胶层能够起到水分屏障的作用,胶层内部木材的含水率变化很小,在使用中受空气湿度变化影响的主要是表层的竹材部分,而且表层竹材越薄的竹木复合地板其含水率越早与环境达到平衡;芯层厚度对竹木复合地板翘曲变形率有较大影响,而表层厚度对其翘曲变形率影响较小.该研究可为竹木复合地板的制造设计提供依据.     

Microbiological Events After a Fire in a High-rise Building

Water used to control a fire on an upper floor in a highrise office building wetted furnishings and construction materials on lower floors and resulted in the amplification of microorganisms especially mesophilic and thermotolerant fungi. Concentrations of fungi in indoor air including Aspergillus, Penicillium and Paecilomyces approached or exceeded 10⁴ colony forming units per cubic meter (cfu/m³). Airborne endotoxin levels increased about 1 order of magnitude over background levels. Sampling for fungi using both culture plate impactors and spore traps showed that spores were migrating from water damaged to undamaged areas in the office complex. Elevator shafts traversing water damaged floors likely provided the major dispersion pathway of spores into occupied areas. Construction materials such as plaster ceilings that had been wetted during the fire but were free of visual fungal contamination were found to be strong fungal reservoirs after the building had thoroughly dried. Management of microbial contaminants after a fire in a highrise building is an important public health concern and therefore an essential aspect of building restoration.     

Airborne and dust borne microorganisms in selected Polish libraries and archives

The aims of this work were to quantitatively and qualitatively study culturable fungi and bacteria in the air and settled dust in the storerooms of five Polish libraries and archives as well as to estimate the effect of water intrusion on the microbial air quality indoors. In all studied storerooms, the total bioaerosol concentrations at the workplaces ranged from 100 to 1000 cfu/m³. The most prevalent part of the storerooms’ bioaerosol consisted of bacteria, mainly Staphylococcus spp. and Micrococcus spp., followed by filamentous fungi. In four of the studied premises, fungal aerosol concentrations were below 100 cfu/m³. The only exception was observed in the fifth storeroom, which has been periodically flooded with rainwater and where significantly higher concentrations of fungal aerosol were measured. Among the identified fungal species, those of the genus Penicillium were the most numerous. Moreover, Trichothecium laxicephalum and Alternaria tenuis were present in all of the examined storerooms.