采用增湿-去湿工艺的竖直列管式脱盐装置的实验研究

A vertical tubular desalination unit with shell and tube structure was built to perform humidification and dehumidification simultaneously on the tube and shell side of the column, respectively. The effects of several operating conditions on the productivity and thermal efficiency of the column were investigated. The results show that both the productivity and thermal efficiency of the column enhance with the elevation of the inlet water temperature. The flow rates of water and carrier gas both have optimal operating ranges, which are 10-30kg·h-1 and 4-7kg·h-1 for the present column, respectively. Meanwhile, the increase of external steam flow rate will promote the productivity of the column but reduce its thermal efficiency.     

丙烷脱氢Cr_2O_3/Al_2O_3催化剂烧焦再生过程的模型化与模拟(英文)

A heterogeneous model is developed for the regeneration of the Cr2O3/Al2O3 catalyst for the propane dehydrogenation process by considering the internal mass transfer and external mass/heat transfer during the coke combustion. Simulation shows that under practical operating conditions, multi-steady states exist for the catalyst pellets and the catalyst temperature is sensitive to gas temperature. However, at increased mass flow rate or lowered oxygen concentration, multi-steady states will not appear. Under the strong influences of film diffusion, the coke in the packed bed reactor will first be exhausted at the inlet, while if the film diffusion resistance is decreased, the position of first coke exhaustion moves toward the outlet of the reactor.     

基于精细自由基反应机理的丙烷裂解炉炉管CFD模拟(英文)

In the radiant section of cracking furnace, the thermal cracking process is highly coupled with turbulent flow, heat transfer and mass transfer. In this paper, a three-dimensional simulation of propane pyrolysis reactor tube is performed based on a detailed kinetic radical cracking scheme, combined with a comprehensive rigorous computational fluid dynamics（CFD） model. The eddy-dissipation-concept（EDC） model is introduced to deal with turbulence-chemistry interaction of cracking gas, especially for the multi-step radical kinetics. Considering the high aspect ratio and severe gradient phenomenon, numerical strategies such as grid resolution and refinement, stepping method and relaxation technique at different levels are employed to accelerate convergence. Large scale of radial nonuniformity in the vicinity of the tube wall is investigated. Spatial distributions of each radical reaction rate are first studied, and made it possible to identify the dominant elementary reactions. Additionally, a series of operating conditions including the feedstock feed rate, wall temperature profile and heat flux profile towards the reactor tubes are investigated. The obtained results can be used as scientific guide for further technical retrofit and operation optimization aiming at high conversion and selectivity of pyrolysis process.     

Effect of wall temperature modulation on the heat transfer characteristics of droplet-train flow inside a rectangular microchannel

The numerical studies of water–oil two-phase slug flow inside a two-dimensional vertical microchannel subjected to modulated wall temperature boundary conditions have been discussed in the present paper. Many researchers have contributed their efforts in exploring the characteristics of Taylor flows inside microchannel under constant wall heat flux or isothermal wall conditions. However, there is no study available in the literature which discusses the impact of modulated thermal wall boundary conditions on the heat transfer behavior of slug flows inside microchannels. Hence, to bridge this gap, an effort has been made to understand the heat transfer characteristics of the flow under sinusoidal wall temperature conditions. Initially, a single phase flow and heat transfer study was performed in microchannels, and the results of the fully developed velocity profile and heat transfer rate were validated with benchmark analytical results. Then an optimal selection of the combination of sinusoidal thermal wall boundary conditions has been made for the two-phase slug flow study. Later, the effects of amplitude(0 b ε b 0.03) and frequency(0 b ω b 750π rad·s~(-1)) of the sinusoidal wall temperature profile on the heat transfer have been studied using the optimal combination of the wall boundary conditions. The results of the numerical study using modulated temperature conditions on channel walls showed a significant improvement in the heat transfer over liquid-only flow by approximately 50% as well as over two-phase flow without wall temperature modulation. The non-dimensional temperature contours obtained for different cases of temperature modulation clearly explain the root cause of such improvement in the heat transfer. Besides,the results based on the hydrodynamics of the flow have also been reported in terms of variation of droplet shapes and film thickness. The influence of Capillary number on the film thickness as well as heat transfer rates has also been discussed. In addition, the measured film thickness has also been compared with that calculated using standard empirical and analytical models available in the literature. The heat transfer rate obtained from the numerical study for the case of unmodulated wall temperature was found to be in a close match with a phenomenological model to evaluate slug flow heat transfer having a mean absolute deviation of 7.56%.     

Developments in the understanding of gas–solid contact efficiency in the circulating fluidized bed riser reactor:A review

In the last several decades, circulating fluidized bed reactors have been studied in many aspects including hydrodynamics, heat and mass transfer and gas–solid two phase contacting. However, despite the abundance of review papers on hydrodynamics, there is no summary paper on gas–solid contact efficiency to date, especially on high density circulating fluidized beds(CFBs). This paper gives an introduction to, and a review of the measurement of contact efficiency in circulating fluidized bed riser. Firstly, the popular testing method of contact efficiency including the method of heating transfer experiment and hot model reaction are discussed, then previous published papers are reviewed based on the discussed methods. Some key results of the experimental work are described and discussed. Gas–solid contact efficiency is affected by the operating conditions as well as the particle size distribution. The result of the contact efficiency shows that the CFB riser is far away from an ideal plug flow reactor due to the characteristics of hydrodynamics in the riser. Lacunae in the available literature have been delineated and recommendations have been made for further work.     

Experimental mass transfer coefficients in a pilot plant multistage column extractor

The volumetric overall mass transfer coefficients in a multistage column have been measured using axial dispersion model for toluene–acetone–water system. The effect of operating parameters on the volumetric overall mass transfer coefficients has been investigated for both mass transfer directions. The results show that the mass transfer performance is strongly dependent on rotor speed and mass transfer direction, although only slightly dependent on phase flow rates. In addition, empirical correlations to predict the overall mass transfer coefficients have been developed. The proposed correlations based on dimensionless numbers can be considered as a useful tool for the possible scale up of the multistage column extractor.     

Numerical study of n-heptane/benzene separation by thermal diffusion column

In this article,numerical simulations are performed to investigate the performance of the thermal diffusion column for the separation of n-heptane/benzene mixture.The present work tried to optimize column by analyzing significant parameters such as feed flow rate,temperature and cut.In order to obtain the hydrodynamic and temperature and mass distribution inside thermal diffusion column,computational fluid dynamic(CFD) method is applied to solve the Navier-Stocks equations.Numerical simulations are conducted to study the main parameters in both stationary and time-dependent conditions.By using the separation work unit as a function of cut,the optimal cut for maximum SWU occurs within a limited range of 0.47-0.5 for feed rate between 0.5 and 4 g min-1.Our findings reveal that the optimum feed rate in the range of optimum cut is about 1 g min~(-1).In transient study,results show that the best cut for reaching to steady-state condition is θ=0.5.     

Mass transfer performance of structured packings in a CO2 absorption tower

This paper studies the mass transfer performance of structured packings in the absorption of CO2 from air with aqueous NaOH solution. The Eight structured packings tested are sheet metal ones with corrugations of different geometry parameters. Effective mass transfer area and overall gas phase mass transfer coefficient have been measured in an absorption column of 200 mm diameter under the conditions of gas F-factor in 0.38–1.52 Pa0.5 and aqueous NaOH solution concentration of 0.10–0.15 kmol·m?3. The effects of gas/liquid phase flow rates and packing geometry parameters are also investigated. The results show that the effective mass transfer area changes not only with packing geometry parameters and liquid load, but also with gas F-factor. A new effective mass transfer area correlation on the gas F-factor and the liquid load was proposed, which is found to fit experiment data very well.     

融化过程中作为潜能储存材料的月桂酸的热特性的实验研究

The objective of this study was to establish the thermal characteristics of the lauric acid (95% purity) as a latent heat storage material filled in the annulus of vertical concentric double pipe during its melting process,The temperature data were used to determine the thermal characteristics,including the temporal temperature variations and the effects of the mass flow rate and the inlet temperature of the heat transfer fluid on the heat transfer coefficient and the heat charging fraction during the melting process,The results indicated that the time to reach to heat charging fraction of 1.0 could be altered by changing the mass flow rate and the inlet temperature of the heat transfer fluid.     

An Experimental Study on Thermal Characteristics of Laurie Acid as a Latent Heat Storage Material during Melting Process

The objective of this study was to establish the thermal characteristics of the lauric acid (95% purity) as a latent heat storage material filled in the annulus of vertical concentric double pipe during its melting process. The temperature data were used to determine the thermal characteristics, including the temporal temperature variations and the effects of the mass flow rate and the inlet temperature of the heat transfer fluid on the heat transfer coefficient and the heat charging fraction during the melting process. The results indicated that the time to reach to heat charging fraction of 1.0 could be altered by changing the mass flow rate and the inlet temperature of the heat transfer fluid.     

Insect antifeedant properties of anthranoids from the genusVismia

Vismiones and ferruginins, representatives of a new class of lypophilic anthranoids from the genusVismia were found to inhibit feeding in larvae of species ofSpodoptera, Heliothis, and inLocusta migratoria.     

Direct observation of freeze-thaw instability of latex coatings via high pressure freezing and cryogenic SEM

Despite its industrial importance, the subject of freeze-thaw (F/T) stability of latex coatings has not been studied extensively. There is also a lack of fundamental understanding about the process and the mechanisms through which a coating becomes destabilized. High pressure (2100 bar) freezing fixes the state of water-suspended particles of polymer binder and inorganic pigments without the growth of ice crystals during freezing that produce artifacts in direct imaging scanning electron microscopy (SEM) of fracture surfaces of frozen coatings. We show that by incorporating copolymerizable functional monomers, it is possible to achieve F/T stability in polymer latexes and in low-VOC paints, as judged by the microstructures revealed by the cryogenic SEM technique. Particle coalescence as well as pigment segregation in F/T unstable systems are visualized. In order to achieve F/T stability in paints, latex particles must not flocculate and should provide protection to inorganic pigment and extender particles. Because of the unique capabilities of the cryogenic SEM, we are able to separate the effects of freezing and thawing, and study the influence of the rate of freezing and thawing on F/T stability. Destabilization can be caused by either freezing or thawing. A slow freezing process is more detrimental to F/T stability than a fast freezing process; the latter actually preserves suspension stability during freezing. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004 in Chicago, IL. Tied for first place in The John A. Gordon Best Paper Competition.     

Ethanol and (−)-α-Pinene: Attractant Kairomones for Bark and Ambrosia Beetles in the Southeastern US

In 2002–2004, we examined the flight responses of 49 species of native and exotic bark and ambrosia beetles (Coleoptera: Scolytidae and Platypodidae) to traps baited with ethanol and/or (−)-α-pinene in the southeastern US. Eight field trials were conducted in mature pine stands in Alabama, Florida, Georgia, North Carolina, and South Carolina. Funnel traps baited with ethanol lures (release rate, about 0.6 g/day at 25–28°C) were attractive to ten species of ambrosia beetles (Ambrosiodmus tachygraphus, Anisandrus sayi, Dryoxylon onoharaensum, Monarthrum mali, Xyleborinus saxesenii, Xyleborus affinis, Xyleborus ferrugineus, Xylosandrus compactus, Xylosandrus crassiusculus, and Xylosandrus germanus) and two species of bark beetles (Cryptocarenus heveae and Hypothenemus sp.). Traps baited with (−)-α-pinene lures (release rate, 2–6 g/day at 25–28°C) were attractive to five bark beetle species (Dendroctonus terebrans, Hylastes porculus, Hylastes salebrosus, Hylastes tenuis, and Ips grandicollis) and one platypodid ambrosia beetle species (Myoplatypus flavicornis). Ethanol enhanced responses of some species (Xyleborus pubescens, H. porculus, H. salebrosus, H. tenuis, and Pityophthorus cariniceps) to traps baited with (−)-α-pinene in some locations. (−)-α-Pinene interrupted the response of some ambrosia beetle species to traps baited with ethanol, but only the response of D. onoharaensum was interrupted consistently at most locations. Of 23 species of ambrosia beetles captured in our field trials, nine were exotic and accounted for 70–97% of total catches of ambrosia beetles. Our results provide support for the continued use of separate traps baited with ethanol alone and ethanol with (−)-α-pinene to detect and monitor common bark and ambrosia beetles from the southeastern region of the US.     

Methyl 2,4,6-decatrienoates Attract Stink Bugs and Tachinid Parasitoids

Halyomorpha halys (Stål) (Pentatomidae), called the brown marmorated stink bug (BMSB), is a newly invasive species in the eastern USA that is rapidly spreading from the original point of establishment in Allentown, PA. In its native range, the BMSB is reportedly attracted to methyl (E,E,Z)-2,4,6-decatrienoate, the male-produced pheromone of another pentatomid common in eastern Asia, Plautia stali Scott. In North America, Thyanta spp. are the only pentatomids known to produce methyl 2,4,6-decatrienoate [the (E,Z,Z)-isomer] as part of their pheromones. Methyl 2,4,6-decatrienoates were field-tested in Maryland to monitor the spread of the BMSB and to explore the possibility that Thyanta spp. are an alternate host for parasitic tachinid flies that use stink bug pheromones as host-finding kairomones. Here we report the first captures of adult and nymph BMSBs in traps baited with methyl (E,E,Z)-2,4,6-decatrienoate in central Maryland and present data verifying that the tachinid, Euclytia flava (Townsend), exploits methyl (E,Z,Z)-2,4,6-decatrienoate as a kairomone. We also report the unexpected finding that various isomers of methyl 2,4,6-decatrienoate attract Acrosternum hilare (Say), although this bug apparently does not produce methyl decatrienoates. Other stink bugs and tachinids native to North America were also attracted to methyl 2,4,6-decatrienoates. These data indicate there are Heteroptera in North America in addition to Thyanta spp. that probably use methyl 2,4,6-decatrienoates as pheromones. The evidence that some pentatomids exploit the pheromones of other true bugs as kairomones to find food or to congregate as a passive defense against tachinid parasitism is discussed.     

2007～2008年世界塑料工业进展

收集了2007年7月～2008年6月世界塑料工业的相关资料,介绍了2007～2008年国外塑料工业的发展情况,提供了世界塑料产量、消费量及全球各类树脂的需求量及产能情况.按通用热塑性树脂(聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂)、工程塑料(尼龙、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚)、特种工程塑料(聚苯·硫醚、液晶聚合物、聚醚醚酮)、通用热固性树脂(酚醛、聚氨酯、不饱和聚酯树脂、环氧树脂)不同品种的顺序,对树脂的产量、消费量、供需状况及合成工艺、产品应用开发、树脂品种的延伸及应用的进一步扩展等技术作了详细介绍.     

2005～2006年国外塑料工业进展

收集了2005年7月～2006年6月国外塑料工业的相关资料,介绍了2005—2006年国外塑料工业的发展情况。提供了世界塑料产量、消费量及全球各类树脂生产量以及各国塑料制品的进出口情况。作为对比,介绍了中国塑料的生产情况。按通用热塑性树脂（聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂）、工程塑料（聚酰胺、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚）、通用热固性树脂（酚醛、聚氨酯、不饱和树脂、环氧树脂）、特种工程塑料（聚苯硫醚、液晶聚合物、聚醚醚酮）的品种顺序,对树脂的产量、消费量、供需状况及合成工艺、产品开发、树脂品种的延伸及应用的扩展作了详细的介绍。