Characterization of high flux magnetized helium plasma in SCU-PSI linear device

A high-flux linear plasma device in Sichuan University plasma-surface interaction(SCU-PSI)based on a cascaded arc source has been established to simulate the interactions between helium and hydrogen plasma with the plasma-facing components in fusion reactors.In this paper,the helium plasma has been characterized by a double-pin Langmuir probe.The results show that the stable helium plasma beam with a diameter of 26 mm was constrained very well at a magnetic field strength of 0.3 T.The core density and ion flux of helium plasma have a strong dependence on the applied current,magnetic field strength and gas flow rate.It could reach an electron density of1.2?×?10~(19)m~(-3)and helium ion flux of 3.2?×?10~(22)m~(-2)s~(-1),with a gas flow rate of 4 standard liter per minute,magnetic field strength of 0.2 T and input power of 11 k W.With the addition of-80 Vapplied to the target to increase the helium ion energy and the exposure time of 2 h,the flat top temperature reached about 530°C.The different sizes of nanostructured fuzz on irradiated tungsten and molybdenum samples surfaces under the bombardment of helium ions were observed by scanning electron microscopy.These results measured in the SCU-PSI linear device provide a reference for International Thermonuclear Experimental Reactor related PSI research.     

Experimental and simulation investigation of electrical and plasma parameters in a low pressure inductively coupled argon plasma

The electrical and plasma parameters of a low pressure inductively coupled argon plasma are investigated over a wide range of parameters(RF power, flow rate and pressure) by diverse characterizations. The external antenna voltage and current increase with the augment of RF power, whereas decline with the enhancement of gas pressure and flow rate conversely.Compared with gas flow rate and pressure, the power transfer efficiency is significantly improved by RF power, and achieved its maximum value of 0.85 after RF power injected excess125 W. Optical emission spectroscopy(OES) provides the local mean values of electron excited temperature and electron density in inductively coupled plasma(ICP) post regime, which vary in a range of 0.81 eV to 1.15 eV and 3.7×10~(16)m~(-3)to 8.7×10~(17)m~(-3)respectively. Numerical results of the average magnitudes of electron temperature and electron density in twodimensional distribution exhibit similar variation trend with the experimental results under different operating condition by using COMSOL Multiphysics. By comprehensively understanding the characteristics in a low pressure ICP, optimized operating conditions could be anticipated aiming at different academic and industrial applications.     

Study of double-chamber air arc plasma torch and the application in solid-waste disposal

Arc plasma can be applied in hazardous solid waste disposal for higher temperature than common heating methods, but some practical issues exist in practical engineering application. In this study, an air arc plasma torch with double chambers and magnetic controlling is designed to realize wide variable power and long electrode life. The detailed characteristics and laws of the air arc are studied. The condition parameters of arc current(I), air flow rate(G) and the structure parameters of inlet area ratios and electrode diameters influence both the arc voltage and arc root positions. The arc rotating driven by magnetic field effectively lengthens the electrode life. The gasification process and product of organic wastes by air plasma are influenced largely by the waste compositions and the air flow rate. A furnace structure with more even atmosphere and longer residence time should be considered for better gasification. Oxygen-deficient environment is important to suppress NOxformation during the application of air plasma. Inorganic solid wastes can be melt by the air plasma and cooled down to form compact vitreous structures in which heavy metals can be locked and the leaching rates significantly decrease down.     

Design and characteristics of a triple-cathode cascade plasma torch for spheroidization of metallic powders

Arc plasma torch is an effective tool for spheroidization of metallic powders. However, as most conventional plasma torches were not specifically designed for plasma spheroidization, they may exhibit the disadvantages of the radial injection of powders, large fluctuations in the arc voltage, large gas flow rate, and disequilibrium between multiple plasma jets during the spheroidization process. Therefore, this paper presents a triple-cathode cascade plasma torch (TCCPT) for plasma spheroidization. Its structural design, including three cathodes, a common anode, and three sets of inter-electrodes, are detailed to ensure that powders can be inserted into the plasma jet by axial injection, the arc voltage fluctuations are easily maintained at a low level, and the plasma torches can work at a relatively small gas flow rate. Experimental results showed that the proposed TCCPT exhibits the following characteristics: (1) a relatively small arc voltage fluctuation within 5.3%; (2) a relatively high arc voltage of 75 V and low gas flow rate range of 10–30 SLM; (3) easy to be maintained at the equilibrium state with the equilibrium index of the three plasma jets within 3.5 V. Furthermore, plasma spheroidization experiments of SUS304 stainless steel powers were carried out using the proposed TCCPT. Results verified that the proposed TCCPT is applicable and effective for the spheroidization of metallic powders with wide size distribution.     

Influence of atmospheric gases on the treatment of miscellaneous solid wastes by plasma melting technology

The material properties of the treated waste forms and the behavior of radionuclides found in the plasma melting tests of simulated miscellaneous solid wastes (iron, fly ash and wood) with cold tracers were examined by using different heating atmospheric gases. The material properties were changed with increasing iron oxide content in the slag layers by changing atmospheric gases. The results showed a homogeneous distribution of cold tracers and low leaching rate of it from the treated waste forms appropriate for shallow land burial site disposal in every atmospheric gas. The high residual rate of Cs in the slag layers (about 70%) was obtained in the plasma melting process except the extremely high reductive atmospheric conditions.     

Modelling Study to Compare the Flow and Heat Transfer Characteristics of Low-Power Hydrogen, Nitrogen and Argon Arc-Heated Thrusters

A modelling study is performed to compare the plasma flow and heat transfer characteristics of low-power arc-heated thrusters (arcjets) for three different propellants: hydrogen, nitrogen and argon. The all-speed SIMPLE algorithm is employed to solve the governing equations, which take into account the effects of compressibility, Lorentz force and Joule heating, as well as the temperature- and pressure-dependence of the gas properties. The temperature, velocity and Mach number distributions calculated within the thruster nozzle obtained with different propellant gases are compared for the same thruster structure, dimensions, inlet-gas stagnant pressure and arc currents. The temperature distributions in the solid region of the anode-nozzle wall are also given. It is found that the flow and energy conversion processes in the thruster nozzle show many similar features for all three propellants. For example, the propellant is heated mainly in the near-cathode and constrictor region, with the highest plasma temperature appearing near the cathode tip; the flow transition from the subsonic to supersonic regime occurs within the constrictor region; the highest axial velocity appears inside the nozzle; and most of the input propellant flows towards the thruster exit through the cooler gas region near the anode-nozzle wall. However, since the properties of hydrogen, nitrogen and argon, especially their molecular weights, specific enthalpies and thermal conductivities, are different, there are appreciable differences in arcjet performance. For example, compared to the other two propellants, the hydrogen arcjet thruster shows a higher plasma temperature in the arc region, and higher axial velocity but lower temperature at the thruster exit. Correspondingly, the hydrogen arcjet thruster has the highest specific impulse and arc voltage for the same inlet stagnant pressure and arc current. The predictions of the modelling are compared favourably with available experimental results.     

Characteristics of Atmospheric Pressure Rotating Gliding Arc Plasmas

In this work,a novel direct current (DC) atmospheric pressure rotating gliding arc (RGA) plasma reactor has been developed for plasma-assisted chemical reactions.The influence of the gas composition and the gas flow rate on the arc dynamic behaviour and the formation of reactive species in the N2 and air gliding arc plasmas has been investigated by means of electrical signals,high speed photography,and optical emission spectroscopic diagnostics.Compared to conventional gliding arc reactors with knife-shaped electrodes which generally require a high flow rate (e.g.,10-20 L/min) to maintain a long arc length and reasonable plasma discharge zone,in this RGA system,a lower gas flow rate (e.g.,2 L/min) can also generate a larger effective plasma reaction zone with a longer arc length for chemical reactions.Two different motion patterns can be clearly observed in the N2 and air RGA plasmas.The time-resolved arc voltage signals show that three different arc dynamic modes,the arc restrike mode,takeover mode,and combined modes,can be clearly identified in the RGA plasmas.The occurrence of different motion and arc dynamic modes is strongly dependent on the composition of the working gas and gas flow rate.     

Diagnosing the Fine Structure of Electron Energy Within the ECRIT Ion Source

The ion source of the electron cyclotron resonance ion thruster(ECRIT) extracts ions from its ECR plasma to generate thrust, and has the property of low gas consumption(2 sccm,standard-state cubic centimeter per minute) and high durability. Due to the indispensable effects of the primary electron in gas discharge, it is important to experimentally clarify the electron energy structure within the ion source of the ECRIT through analyzing the electron energy distribution function(EEDF) of the plasma inside the thruster. In this article the Langmuir probe diagnosing method was used to diagnose the EEDF, from which the effective electron temperature, plasma density and the electron energy probability function(EEPF) were deduced. The experimental results show that the magnetic field influences the curves of EEDF and EEPF and make the effective plasma parameter nonuniform. The diagnosed electron temperature and density from sample points increased from 4 eV/2×10~(16)m~(-3) to 10 eV/4×10~(16)m(-3) with increasing distances from both the axis and the screen grid of the ion source. Electron temperature and density peaking near the wall coincided with the discharge process. However, a double Maxwellian electron distribution was unexpectedly observed at the position near the axis of the ion source and about 30 mm from the screen grid. Besides, the double Maxwellian electron distribution was more likely to emerge at high power and a low gas flow rate. These phenomena were believed to relate to the arrangements of the gas inlets and the magnetic field where the double Maxwellian electron distribution exits. The results of this research may enhance the understanding of the plasma generation process in the ion source of this type and help to improve its performance.     

Design,Construction and Characterization of AC Atmospheric Pressure Air Non-thermal Plasma Jet

This paper presents the design and construction of non-thermal plasma jet device which was built in plasma phys. Dept., NRC, AEA, Egypt with a plasma application group. This design will be useful to initiate research in different fields such as low temperature plasma, polymer and biomedical applications. The experimental operation of this device is conducted with power supply of (10 kV, 30 mA, and 20 kHz). The discharge process takes place by using Air as input gas with different flow rates. The experimental results showed that the maximum plasma jet length of 7 mm is detected at air flow rate of 12 L/min. The electrical characteristics of discharge at different flow rates of Air such as discharge voltage, current, mean power, power efficiency, and energy have been studied by using potential dividers and Lissajous figure techniques. The results of plasma jet temperature along the jet length showed that the jet plasma has approximately a room temperature at the end of jet column.     

Numerical modelling of a low power non-transferred arc plasma reactor for methane conversion

Thermal flow characteristics and the methane conversion reaction in a low power arc plasma reactor for efficient storage and transport of methane, which is the main component of shale gas, were simulated. The temperature and velocity distributions were calculated according to the type of discharge gases and arc current level by a self-developed magnetohydrodynamics (MHD) code and a commercial ANSYS-FLUENT code; the transport of chemical species was analyzed as including the chemical reactions of methane conversion. The simulated results were verified by the comparison of calculated and measured arc voltages with permissible low error as under 4%. Three C₂ hydrocarbon gases with ethane (C₂H₆), ethylene (C₂H₄), and acetylene (C₂H₂) were selected as the converted species of methane from experimental data. The mass fraction of C₂ hydrocarbons and hydrogen as the product of the conversion reaction at the reactor was also calculated. Those values show good agreement with the actual experimental results in that the major conversion reaction occurred in C₂H₂ and hydrogen, and the conversions to C₂H₆, C₂H₄, and hydrogen were minor reactions of methane pyrolysis conversion.     

Effect of methane content and the oscillating electric field between electrodes on atmospheric Ar/methane plasma jet and DLC coating deposition

In this work, the effects of the methane gas flow and the internal oscillating electric field between electrodes on radio-frequency(RF) atmospheric pressure argon/methane plasma jet and process of diamond-like carbon(DLC) film deposition have been investigated. Properties of RF atmospheric Ar/methane plasma jet such as active species density, length, electron temperature,appearance and ionization process of argon/methane plasma jet are changed due to the changing of methane flow content and electric field vector and its gradient. With increasing methane flow,the formation of C2 hydrocarbon and CH band content is decreased because injected electrical energy to a mixture of Ar/methane gases is insufficient to stabilize the ionization process of methane gas and the electrical-chemical reaction rate is decreased. With shortening the gas gap between two electrodes, electric field strength and its gradient are increased leading to more energy injection to the electron. Electrical-chemical reactions are strengthened leading to increasing the CH band content. These phenomena introduce the Ar/methane plasma jet in different modes causing to deposit the DLC film with different structures and properties. With using quartz glass and alumina ceramic as dielectric barriers tubes, RF atmospheric pressure Ar/methane plasma jet has been used to deposit DLC coating in different modes. Increasing methane content and shortening the gas gap leads to decreasing sp3 bonded content and the quality of the deposited film.     

Plume diagnostics of BUSTLab microwave electrothermal thruster using Langmuir and Faraday probes

This study presents the Langmuir and Faraday probe measurements conducted to determine the plume characteristics of the BUSTLab microwave electrothermal thruster (MET). The thruster, designed to operate at 2.45 GHz frequency, is run with helium, argon and nitrogen gases as the propellant. For the measurements, the propellant volume flow rate and the delivered microwave power levels are varied. Experiments with nitrogen gas revealed certain operation regimes where a very luminous plume is observed. With the use of in-house-built Langmuir probes and a Faraday probe with guard ring, thruster plume electron temperature, plasma density and ion current density values are measured, and the results are presented. The measurements show that MET thruster plume effects on spacecraft will likely be similar to those of the arcjet plume. It is observed that the measured plume ion flux levels are very low for the high volume flow rates used for the operation of this thruster.     

等离子体切割的弧特性研究

基于弧柱双区域近似的简单理论,研究了空气等离了体切割产生的等离子体弧特性,给出了不同工作条件（空气流速及喷嘴直径）下,弧的半径、电压及喷嘴出口处压强随弧电流变化的计算结果。研究结果表明,计算与实验结果符合得好。同时讨论了空气流速及喷嘴直径对等离子体功率及作用力的影响。     

Numerical simulation and experimental research on an inductively coupled RF plasma cathode

In this study, numerical simulation and discharge current tests were conducted on an inductively coupled radio frequency (RF) plasma cathode. Numerical simulations and experimental measurements were performed to study the factors influencing the electron extraction characteristics, including the gas type, gas flow, input power and extracting voltage. The simulation results were approximately consistent with the experimental results. We experimentally found that the RF input power mainly determines the extracted electron current. An electron current greater than 1 A was acquired at 270 W (RF input power), 2.766 sccm (xenon gas). Our results prove that an inductively coupled RF plasma cathode can be reasonable and feasible, particularly for low power electric propulsion devices.     

Effects of inter-electrode insertion on the performance and thermal flow fields of a hollow-electrode plasma torch

The effects of inter-electrode insertion on the performance of a hollow-electrode plasma torch have been investigated by numerical analysis. Simulation results revealed that when inter-electrodes are inserted, the arc voltages and plasma powers increase due to the increase in the arc length. In addition,it was predicted that thermal efficiency can be improved with the increase in plasma power by injecting plasma gases through the gaps between inter-electrodes. These unique effects of inter-electrode insertion are a result of the plasma temperatures adjusting themselves to increase arc voltages when the arc column is contracted radially by increasing gas-flow rate or decreasing inter-electrode diameter.     

Design and Development of a Power Supply System for NBI Test Stand of EAST

A neutral beam injector (NBI) test stand was constructed to develop a multi-megawatt prototype ion source as an auxiliary heating system on experimental advanced superconducting tokamak. A power supply system for the NBI test stand components such as a set of dc power supplies for plasma generator, a dc high voltage power supply of a tetrode accelerator, a transmission line and a surge energy suppressor. Stable arc discharges of the plasma generator with hydrogen gases for 100 s long pulse have been produced by six Langmuir probes feedback loop regulation mode to control the arc power supply. The 4 MW hydrogen ion beam of 1 s is extracted with beam energy of 80 keV and the beam current of 52 A. The dc high voltage power supply for the plasma grid of the prototype ion source was designed to contribute maximum voltage of 100 kV and current of 100 A. The high voltage power output is continuously adjustable to satisfy with plasma physics experiment in operation frequency of 10 Hz. To prevent damage of the beam source at high voltage breakdown, core snubber using deltamax soft magnetic materials have been adopted to satisfy the input energy into the accelerator from the power supply can be reduced to about 5 J in the case of breakdown at 80 kV. For the transmission line, a disc shape multi cable coaxial configuration was adopted and which the dimension of the diameter is 140 mm at the core snubber. The major issues of discharge characteristics with long pulse and beam extraction with high power for the prototype ion source were investigated on the NBI test stand.     

Characteristics of Single Cathode Cascaded Bias Voltage Arc Plasma

A single cathode with a cascaded bias voltage arc plasma source has been developed with a new quartz cathode chamber,instead of the previous copper chambers,to provide better diagnostic observation and access to the plasma optical emission.The cathode chamber cooling scheme is also modified to be naturally cooled only by light emission without cooling water to improve the optical thin performance in the optical path.A single-parameter physical model has been developed to describe the power dissipated in the cascaded bias voltage arc discharge argon plasmas,which have been investigated by utilizing optical emission spectroscopy(OES) and Langmuir probe.In the experiments,discharge currents from 50 A to 100 A,argon flow rates from 800 sccm to 2000 sccm and magnetic fields of 0.1 T and 0.2 T were chosen.The results show:(a) the relationship between the averaged resistivity and the averaged current density exhibits an empirical scaling law as η∝ j~(-0.63369) and the power dissipated in the arc has a strong relation with the filling factor;(b) through the quartz,the argon ions optical emission lines have been easily observed and are dominating with wavelengths between 340 nm and 520 nm,which are the emissions of Ar~+-434.81 nm and Ar~+-442.60 nm line,and theintensities are increasing with the arc current and decreasing with the inlet argon flow rate;and(c) the electron density and temperature can reach 2.0 × 10~(19) m~(-3) and 0.48 eV,respectively,under the conditions of an arc current of 90 A and a magnetic field of 0.2 T.The half-width of the n_e radial profile is approximatively equal to a few Larmor radii of electrons and can be regarded as the diameter of the plasma jet in the experiments.     

Comparison of Reynolds average Navier-Stokes turbulence models in numerical simulations of the DC arc plasma torch

Five turbulence models of Reynolds average Navier-Stokes(RANS),including the standard k-ω model,the RNG k-e model taking into account the low Reynolds number effect,the realizable k-ω model,the SST k-ω model,and the Reynolds stress model(RSM),are employed in the numerical simulations of direct current(DC)arc plasma torches in the range of arc current from 80 A to 240 A and air gas flow rate from 10 m^3 h^-1 to 50 m^3 h^-1.The calculated voltage,electric field intensity,and the heat loss in the arc chamber are compared with the experiments.The results indicate that the arc voltage,the electric field,and the heat loss in the arc chamber calculated by using the standard k-ω model,the RNG k-ωmodel taking into account the low Reynolds number effect,and the realizable k-ω model are much larger than those in the experiments.The RSM predicts relatively close results to the experiments,but fails in the trend of heat loss varying with the gas flow rate.The calculated results of the SST k-ω model are in the best agreement with the experiments,which may be attributed to the reasonable predictions of the turbulence as well as its distribution.     

OH and O radicals production in atmospheric pressure air/Ar/H2O gliding arc discharge plasma jet

Atmospheric pressure air/Ar/H_2O gliding arc discharge plasma is produced by a pulsed dc power supply. An optical emission spectroscopic(OES) diagnostic technique is used for the characterization of plasmas and for identifications of OH and O radicals along with other species in the plasmas. The OES diagnostic technique reveals the excitation Tx?≈?5550–9000 K, rotational Tr?≈?1350–2700 K and gas Tg?≈?850–1600 K temperatures, and electron density n?(1.1-1.9) ′101 4 cm~(-3) e under different experimental conditions. The production and destruction of OH and O radicals are investigated as functions of applied voltage and air flow rate. Relative intensities of OH and O radicals indicate that their production rates are increased with increasing Ar content in the gas mixture and applied voltage. nereveals that the higher densities of OH and O radicals are produced in the discharge due to more effective electron impact dissociation of H_2O and O_2 molecules caused by higher kinetic energies as gained by electrons from the enhanced electric field as well as by enhanced n e.The productions of OH and O are decreasing with increasing air flow rate due to removal of Joule heat from the discharge region but enhanced air flow rate significantly modifies discharge maintenance properties. Besides, Tgsignificantly reduces with the enhanced air flow rate. This investigation reveals that Ar plays a significant role in the production of OH and O radicals.     

High concentration xylene decomposition and diagnostic analysis by non-thermal plasma in a DBD reactor

Dielectric barrier discharge (DBD) is utilized to decompose xylene vapor in mobile gas under normal atmospheric pressure.The plasma is generated by an AC power source with a frequency of 6 kHz.In the experiment,the discharge power on the DBD reactor was calculated by a Lissajous figure,and the specific input energy (SIE) of different discharge voltage or residence time was obtained.The concentrations of xylene,carbon monoxide and carbon dioxide in the gas were analyzed by gas chromatography.The spectra of DBD were diagnosed using a spectrometer.We calculated the conversion rate (CR),mineralization rate (MR) and carbon dioxide selectivity.The relationship between these quantities and the SIE was analyzed.The experimental results show that high concentration xylene can be decomposed mostly by DBD plasma.The CR can reach as high as 90％ with the main product of carbon dioxide.