CO2 capture using oxygen enhanced combustion strategies for natural gas power plants

This paper describes a series of experiments conducted with natural gas in air and in mixtures of oxygen and recycled flue gas, termed O₂/CO₂ recycle combustion. The objective is to enrich the flue gas with CO₂ to facilitate its capture and sequestration. Detailed measurements of gas composition, flame temperature and heat flux profiles were taken inside CANMET's 0.3 MWth down-fired vertical combustor fitted with a proprietary pilot scale burner. Flue gas composition was continuously monitored. The effects of burner operation, including swirling of secondary stream and air staging, on flame characteristics and NO_x emissions were also studied. The results of this work indicate that oxy-gas combustion techniques based on O₂/CO₂ combustion with flue gas recycle offer excellent potential for retrofit to conventional boilers for CO₂ emission abatement. Other benefits of the technology include considerable reduction and even elimination of NO_x emissions, improved plant efficiency due to lower gas volume and better operational flexibility.     

Partial O2-fired coal power plant with post-combustion CO2 capture: A retrofitting option for CO2 capture ready plants

In the work presented in this paper, an alternative process concept that can be applied as retrofitting option in coal-fired power plants for CO₂ capture is examined. The proposed concept is based on the combination of two fundamental CO₂ capture technologies, the partial oxyfuel mode in the furnace and the post-combustion solvent scrubbing. A 330 MW_el Greek lignite-fired power plant and a typical 600 MW_el hard coal plant have been examined for the process simulations. In a retrofit application of the ECO-Scrub technology, the existing power plant modifications are dominated by techno-economic restrictions regarding the boiler and the steam turbine islands. Heat integration from processes (air separation, CO₂ compression and purification and the flue gas treatment) can result in reduced energy and efficiency penalties. In the context of this work, heat integration options are illustrated and main results from thermodynamic simulations dealing with the most important features of the power plant with CO₂ capture are presented for both reference and retrofit case, providing a comparative view on the power plant net efficiency and energy consumptions for CO₂ capture. The operational characteristics as well as the main figures and diagrams of the plant’s heat balances are included.     

Dynamic modelling of CO2 absorption for post combustion capture in coal-fired power plants

Power generation from fossil fuel-fired power plants is the largest single source of CO₂ emissions. Post combustion capture via chemical absorption is viewed as the most mature CO₂ capture technique. This paper presents a study of the post combustion CO₂ capture with monoethanolamine (MEA) based on dynamic modelling of the process. The aims of the project were to compare two different approaches (the equilibrium-based approach versus the rate-based approach) in modelling the absorber dynamically and to understand the dynamic behaviour of the absorber during part load operation and with disturbances from the stripper. A powerful modelling and simulation tool gPROMS was chosen to implement the proposed work. The study indicates that the rate-based model gives a better prediction of the chemical absorption process than the equilibrium-based model. The dynamic simulation of the absorber indicates normal absorber column operation could be maintained during part load operation by maintaining the ratio of the flow rates of the lean solvent and flue gas to the absorber. Disturbances in the CO₂ loading of the lean solvent to the absorber significantly affect absorber performance. Further work will extend the dynamic modelling to the stripper for whole plant analysis.     

Experimental programme in CIUDEN's CO2 capture technology development plant for power generation

Energy projections made by the World Energy Council, the International Energy Agency (IEA) and the US Energy Information Administration give similar pictures of the dominant role of fossil fuel in the future primary energy global demand and the necessity of incorporating CCS Technologies as part of the portfolio of solutions to reach the target world emission reduction in the coming years. Without CCS, CO₂ emission levels by 2050 are expected to increase by 70%.One of the most relevant initiatives for the deployment of CCS technologies is promoted by the Spanish Government through the institution Fundacion Ciudad de la Energia (CIUDEN). CIUDEN is developing a complete programme focusing on the development of CCT and CCS technologies in Europe.CIUDEN's CO₂ capture programme includes the construction and operation of a Technology Development Plant (TDP) in NW Spain (El Bierzo). The construction of the installation started in November 2008 and incorporates the following technologies: fuel preparation system, pulverised coal boiler (20 MWth), circulating fluidized bed boiler (30 MWth), biomass gasifier (3 MWth), flue gas cleaning train for NO_x, dust and SO_x, and CO₂ processing unit.This paper describes CIUDEN's TDP for CO₂ capture, focusing on the particularities of the installation and design, and especially on the PC unit and equipment required for its operation. The experimental programme currently under way is also described.Results are expected to be an extraordinary advance in the development and strengthening of CCT and CCS technologies, particularly oxycombustion.     

Techno-economic evaluation of a PVAm CO2-selective membrane in an IGCC power plant with CO2 capture

Published data for an operating power plant, the ELCOGAS 315 MWe Puertollano plant, has been used as a basis for the simulation of an integrated gasification combined cycle process with CO₂ capture. This incorporated a fixed site carrier polyvinylamine membrane to separate the CO₂ from a CO-shifted syngas stream. It appears that the modified process, using a sour shift catalyst prior to sulphur removal, could achieve greater than 85% CO₂ recovery at 95 vol% purity. The efficiency penalty for such a process would be approximately 10% points, including CO₂ compression. A modified plant with CO₂ capture and compression was calculated to cost €2320/kW, producing electricity at a cost of 7.6 € cents/kWh and a CO₂ avoidance cost of about €40/tonne CO₂.     

Ca-based sorbent looping combustion for CO2 capture in pilot-scale dual fluidized beds

To demonstrate process feasibility of in situ CO₂ capture from combustion of fossil fuels using Ca-based sorbent looping technology, a flexible atmospheric dual fluidized bed combustion system has been constructed. Both reactors have an ID of 100 mm and can be operated at up to 1000 °C at atmospheric pressure. This paper presents preliminary results for a variety of operating conditions, including sorbent looping rate, flue gas stream volume, CaO/CO₂ ratio and combustion mode for supplying heat to the sorbent regenerator, including oxy-fuel combustion of biomass and coal with flue gas recirculation to achieve high-concentration CO₂ in the off-gas. It is the authors' belief that this study is the first demonstration of this technology using a pilot-scale dual fluidized bed system, with continuous sorbent looping for in situ CO₂ capture, albeit at atmospheric pressure. A multi-cycle test was conducted and a high CO₂ capture efficiency (> 90%) was achieved for the first several cycles, which decreased to a still acceptable level (> 75%) even after more than 25 cycles. The cyclic sorbent was sampled on-line and showed general agreement with the features observed using a lab-scale thermogravimetric analysis (TGA) apparatus. CO₂ capture efficiency decreased with increasing number of sorbent looping cycles as expected, and sorbent attrition was found to be another significant factor to be limiting sorbent performance.     

Microporous phenol-formaldehyde resin-based adsorbents for pre-combustion CO2 capture

Different types of phenolic resins were used as precursor materials to prepare adsorbents for the separation of CO₂ in pre-combustion processes. In order to obtain highly microporous carbons with suitable characteristics for the separation of CO₂ and H₂ under high pressure conditions, phenol-formaldehyde resins were synthesised under different conditions. Resol resins were obtained by using an alkaline environment while Novolac resins were synthesised in the presence of acid catalysts. In addition, two organic additives, ethylene glycol (E) and polyethylene glycol (PE) were included in the synthesis. The phenolic resins thus prepared were carbonised at different temperatures and then physically activated with CO₂. The carbons produced were characterised in terms of texture, chemical composition and surface chemistry. Maximum CO₂ adsorption capacities at atmospheric pressure were determined in a thermogravimetric analyser. Values of up to 10.8 wt.% were achieved. The high-pressure adsorption of CO₂ at room temperature was determined in a high-pressure magnetic suspension balance. The carbons tested showed enhanced CO₂ uptakes at high pressures (up to 44.7 wt.% at 25 bar). In addition, it was confirmed that capture capacities depend highly on the microporosity of the samples, the narrow micropores (pore widths of less than 0.7 nm) being the most active in CO₂ adsorption at atmospheric pressure. The results presented in this work suggest that phenol-formaldehyde resin-derived activated carbons, particularly those prepared with the addition of ethylene glycol, show great potential as adsorbents for pre-combustion CO₂ capture.     

Techno-economic evaluation of advanced IGCC lignite coal fuelled power plants with CO2 capture

The techno-economic evaluation of four novel integrated gasification combined cycle (IGCC) power plants fuelled with low rank lignite coal with CO₂ capture facility has been investigated using ECLIPSE process simulator. The performance of the proposed plants was compared with two conventional IGCC plants with and without CO₂ capture. The proposed plants include an advanced CO₂ capturing process based on the Absorption Enhanced Reforming (AER) reaction and the regeneration of sorbent materials avoiding the need for sulphur removal component, shift reactor and/or a high temperature gas cleaning process. The results show that the proposed CO₂ capture plants efficiencies were 18.5–21% higher than the conventional IGCC CO₂ capture plant. For the proposed plants, the CO₂ capture efficiencies were found to be within 95.8–97%. The CO₂ capture efficiency for the conventional IGCC plant was 87.7%. The specific investment costs for the proposed plants were between 1207 and 1479 €/kW_e and 1620 €/kW_e and 1134 €/kW_e for the conventional plants with and without CO₂ capture respectively. Overall the proposed IGCC plants are cleaner, more efficient and produce electricity at cheaper price than the conventional IGCC process.     

Reactivation and remaking of calcium aluminate pellets for CO2 capture

CaO-based pellets supported with aluminate cements show superior performance in carbonation/calcination cycles for high-temperature CO₂ capture. However, like other CaO-based sorbents, their CO₂ carrying activity is reduced after increasing numbers of cycles under high-temperature, high-CO₂ concentration conditions. In this work the feasibility of their reactivation by steam or water and remaking (reshaping) was investigated. The pellets, prepared from three limestones, Cadomin and Havelock (Canada) and Katowice (Poland, Upper Silesia), were tested in a thermogravimetric analyzer (TGA). The cycles were performed under realistic CO₂ capture conditions, which included calcination in 100% CO₂ at temperatures up to 950 °C. Typically, after 30 cycles, samples were hydrated for 5 min with saturated steam at 100 °C in a laboratory steam reactor (SR). Moreover, larger amounts of pellets were cycled in a tube furnace (TF), hydrated with water and reshaped, and tested to determine their CO₂ capture activity in the TGA. It was found that, after the hydration stage, pellets recovered their activity, and more interestingly, pellets that had experienced a longer series of cycles responded more favorably to reactivation. Moreover, it was found that conversion of pellets increased after about 70 cycles (23%), reaching 33% by about cycle 210, with no reactivation step. Scanning electron microscope (SEM) analyses showed that the morphology of the low-porosity shell formed at the pellet surface during cycles, which limits conversion, was eliminated after a short period (5 min) of steam hydration. The nitrogen physisorption analyses (BET, BJH) of reshaped spent pellets from cycles in the TF confirmed that sorbent surface area and pore size distribution were similar to those of the original pellets. The main alumina compound in remade pellets as determined by XRD was mayenite (Ca₁₂Al₁₄O₃₃). These results showed that, with periodic hydration/remaking steps, pellets can be used for extended times in CO₂ looping cycles, regardless of capture/regeneration conditions.     

CO2 capture by adsorption with nitrogen enriched carbons

The success of CO₂ capture with solid sorbents is dependent on the development of a low cost sorbent with high CO₂ selectivity and adsorption capacity. Immobilised amines are expected to offer the benefits of liquid amines in the typical absorption process, with the added advantages that solids are easy to handle and that they do not give rise to corrosion problems. In this work, different alkylamines were evaluated as a potential source of basic sites for CO₂ capture, and a commercial activated carbon was used as a preliminary support in order to study the effect of the impregnation. The amine coating increased the basicity and nitrogen content of the carbon. However, it drastically reduced the microporous volume of the activated carbon, which is chiefly responsible for CO₂ physisorption, thus decreasing the capacity of raw carbon at room temperature.     

Evaluation of solid sorbents as a retrofit technology for CO2 capture

Processes based upon solid sorbents are currently under consideration for post-combustion CO₂ capture. Twenty-four different sorbent materials were examined on a laboratory scale in a cyclic temperature swing adsorption/regeneration CO₂ capture process in simulated coal combustion flue gas. Ten of these materials exhibited significantly lower theoretical regeneration energies compared to the benchmark aqueous monoethanolamine, supporting the hypothesis that CO₂ capture processes based upon solids may provide cost benefits over solvent-based processes. The best performing materials were tested on actual coal-fired flue gas. The supported amines exhibited the highest working CO₂ capacities, although they can become poisoned by the presence of SO₂. The carbon-based materials showed excellent stability but were generally categorized as having low CO₂ capacities. The zeolites worked well under dry conditions, but were quickly poisoned by the presence of moisture. Although no one type of material is without concerns, several of the materials tested have theoretical regeneration energies significantly lower than that of the industry benchmark, warranting further development research.     

Development of low-cost biomass-based adsorbents for postcombustion CO2 capture

In this work a series of carbon adsorbents were prepared from a low-cost biomass residue, olive stones. Two different approaches were studied: activation with CO₂ and heat treatment with gaseous ammonia. The results showed that both methods are suitable for the production of adsorbents with a high CO₂ adsorption capacity, and their potential application in VSA or TSA systems for postcombustion CO₂ capture. It was found that the presence of nitrogen functionalities enhances CO₂ adsorption capacity, especially at low partial pressures.     

CO2 capture capacity of CaO in long series of pressure swing sorption cycles

One promising method for the capture of CO₂ from point sources is through the usage of a lime-based sorbent. Lime (CaO) acts as a CO₂ carrier, absorbing CO₂ from the flue gas (carbonation) and releasing it in a separate reactor (calcination) to create a pure stream of CO₂ suitable for sequestration. One of the challenges with this process is the decay in calcium utilization (CO₂ capture capacity) during carbonation/calcination cycling. The reduction in calcium utilization of natural limestone over large numbers of cycles (>250) was studied. Cycling was accomplished using pressure swing CO₂ adsorption in a pressurized thermogravimetric reactor (PTGA). The effect of carbonation pressure on calcium utilization was studied in CO₂ with the reactor operated at 1000 °C. The pressure was cycled between atmospheric pressure for calcination, and 6, 11 or 21 bar for carbonation. Over the first 250 cycles, the calcium utilization reached a near-asymptotic value of 12.5-27.7%, depending on the cycling conditions. Pressure cycling resulted in improved long-term calcium utilization compared to temperature swing or CO₂ partial pressure swing adsorption under similar conditions. An increased rate of de-pressurization caused an increase in calcium utilization, attributed to fracturing of the sorbent particle during the rapid calcination, as observed via SEM analysis.     

Influence of calcination conditions on carrying capacity of CaO-based sorbent in CO2 looping cycles

This study examines the loss of sorbent activity caused by sintering under realistic CO₂ capture cycle conditions. The samples tested here included two limestones: Havelock limestone from Canada (New Brunswick) and a Polish (Upper Silesia) limestone (Katowice). Samples were prepared both in a thermogravimetric analyzer (TGA) and a tube furnace (TF). Two calcination conditions were employed: in N₂ at lower temperature; and in CO₂ at high temperature. The samples obtained were observed with a scanning electron microscope (SEM) and surface compositions of the resulting materials were analyzed by the energy dispersive X-ray (EDX) method. The quantitative influence of calcination conditions was examined by nitrogen adsorption/desorption tests, gas displacement pycnometry and powder displacement pycnometry; BET surface areas, BJH pore volume distributions, skeletal densities and envelope densities were determined. The SEM images showed noticeably larger CaO sub-grains were produced by calcination in CO₂ during numerous cycles than those seen with calcination in nitrogen. The EDX elemental analyses showed a strong influence of impurities on local melting at the sorbent particle surface, which became more pronounced at higher temperature. Results of BET/BJH testing clearly support these findings on the effect of calcination/cycling conditions on sorbent morphology. Envelope density measurements showed that particles displayed densification upon cycling and that particles calcined under CO₂ showed greater densification than those calcined under N₂. Interestingly, the Katowice limestone calcined/cycled at higher temperature in CO₂ showed an increase of activity for cycles involving calcination under N₂ in the TGA. These results clearly demonstrate that, in future development of CaO-based CO₂ looping cycle technology, more attention should be paid to loss of sorbent activity caused by realistic calcination conditions and the presence of impurities originating from fuel ash and/or limestone.     

Triptycene-based microporous polyimides: Synthesis and their high selectivity for CO2 capture

A series of triptycene-based porous polyimides (STPIs) were synthesized by condensation polymerizations. The structure and properties of these STPIs were characterized by IR, solid ¹³C NMR, powder XRD, SEM, TEM and gas absorption. As STPI-2 with the high thermal stability, they display excellent adsorption ability to CO₂ uptake capacity of 14.6 wt% (273 K), and exhibit the high selectivity of CO₂/N₂ of 107.     

Enhancement of reactivity in surfactant-modified sorbent for CO2 capture in pressurized carbonation

The calcination/carbonation loop of calcium-based (Ca-based) sorbents is considered as a viable technique for CO₂ capture from combustion gases. Recent attempts to improve the CO₂ uptake of Ca-based sorbents by adding calcium lignosulfonate (CLS) with hydration have succeeded in enhancing its effectiveness. The optimum mass ratio of CLS/CaO is 0.5 wt.%. The reduction in particle size and grain size of CaO appeared to be parts of the reasons for increase in CO₂ capture. The primary cause of increase in reactivity of the modified sorbents was the ability of the CLS to retard the sintering rate and thus to remain surface area and pore volume for reaction. The CO₂ uptake of the modified sorbents was also enhanced by elevating the carbonation pressure. Experimental results indicate that the optimal reaction condition of the modified sorbents is at 0.5 MPa and 700 °C and a high conversion of 0.7 is achieved after 10 cycles, by 30% higher than that of original limestone, at the same condition.     

Cyclic CO2 capture behavior of KMnO4-doped CaO-based sorbent

This study examines the CO₂ capture behavior of KMnO₄-doped CaO-based sorbent during the multiple calcination/carbonation cycles. The cyclic carbonation behavior of CaCO₃ doped with KMnO₄ and the untreated CaCO₃ was investigated. The addition of KMnO₄ improves the cyclic carbonation rate of the sorbent above carbonation time of 257 s at each carbonation cycle. When the mass ratio of KMnO₄/CaCO₃ is about 0.5-0.8 wt.%, the sorbent can achieve an optimum carbonation conversion during the long-term cycles. The carbonation temperature of 660-710 °C is beneficial to cyclic carbonation of KMnO₄-doped CaCO₃. The addition of KMnO₄ improves the long-term performance of CaCO₃, resulting in directly measured conversion as high as 0.35 after 100 cycles, while the untreated CaCO₃ retains conversion less than 0.16 at the same reaction conditions. The addition of KMnO₄ decreases the surface area and pore volume of CaCO₃ after 1 cycle, but it maintains the surface area and pores between 26 nm and 175 nm of the sorbent during the multiple cycles. Calculation reveals that the addition of KMnO₄ improves the CO₂ capture efficiency significantly using a CaCO₃ calcination/carbonation cycle and decreases the amount of the fresh sorbent.     

Porous polymers prepared via high internal phase emulsion polymerization for reversible CO2 capture

A series of porous polymers with different pore volumes, pore sizes, and crosslinking densities were synthesized by high internal phase emulsion (HIPE) polymerization. The crosslinked polymerized HIPEs (polyHIPEs) were formed by the copolymerization of 4-vinylbenzyl chloride and divinylbenzene using water droplets in conventional or Pickering HIPEs as the templates. These porous materials were further modified by quaternization and ion exchange to introduce quaternary ammonium hydroxide groups. The resulting polyHIPEs were utilized as sorbents for reversible CO₂ capture from air using the humidity swing. The effect of pore structure on the CO₂ adsorption and desorption processes was studied. The polyHIPEs containing large pores and interconnected porous structures showed improved swing sizes and faster adsorption/desorption kinetics of CO₂ compared to a commercial Excellion membrane with similar functional groups.     

Cyclic calcination/carbonation looping of dolomite modified with acetic acid for CO2 capture

The dolomite modified with acetic acid solution was proposed as a CO₂ sorbent for calcination/carbonation cycles. The carbonation conversions for modified and original dolomites in a twin fixed-bed reactor system with increasing the numbers of cycles were investigated. The carbonation temperature in the range of 630 °C–700 °C is beneficial to the carbonation reaction of modified dolomite. The carbonation conversion for modified dolomite is significantly higher than that for original sorbent at the same reaction conditions with increasing numbers of reaction cycles. The modified dolomite exhibits a carbonation conversion of 0.6 after 20 cycles, while the unmodified sorbent shows a conversion of 0.26 at the same reaction conditions, which is calcined at 920 °C and carbonated at 650 °C. At the high calcination temperature over 920 °C modified dolomite can maintain much higher conversion than unmodified sorbent. The mean grain size of CaO derived from modified dolomite is smaller than that from original sorbent with increasing numbers of reaction cycles. The calcined modified dolomite possesses greater surface area and pore volume than calcined original sorbent during the multiple cycles. The pore volume and pore area distributions for calcined modified dolomite are also superior to those for calcined unmodified sorbent during the looping cycle. The modified dolomite is proved as a new and promising type of regenerable CO₂ sorbent for industrial applications.     

Thermodynamic performance of O2/CO2 gas turbine cycle with chemical recuperation by CO2-reforming of methane

This paper proposes a novel power cycle system composed of chemical recuperative cycle with CO₂–NG (natural gas) reforming and an ammonia absorption refrigeration cycle. In which, the heat is recovered from the turbine exhaust to drive CO₂–NG reformer firstly, and then lower temperature heat from the turbine exhaust is provided with the ammonia absorption refrigeration system to generate chilled media, which is used to cool the turbine inlet gas except export. In this paper, a detailed thermodynamic analysis is carried out to reveal the performance of the proposed cycle and the influence of key parameters on performance is discussed. Based on 1 kg s⁻¹ of methane feedstock and the turbine inlet temperature of 1573 K, the simulation results shown that the optimized net power generation efficiency of the cycle rises up to 49.6% on the low-heating value and the exergy efficiency 47.9%, the new cycle system reached the net electric-power production 24.799 MW, the export chilled load 0.609 MW and 2.743 kg s⁻¹ liquid CO₂ was captured, achieved the goal of CO₂ and NO_x zero-emission.