风机盘管特性参数在低温工况下简便算法的研究

针对低温地热采暖方式的特点，对低温地热采暖系统中采用的风机盘管结构及特性参数进行了改造与优化。分析了系统最佳运行参数及其影响因素；通过对不同型式风机盘管热工性能的试验及风机盘管设备的实验研究，总结出适用于低温地热采暖系统风机盘管总传热系数的简化计算公式，对工程设计具有一定的使用价值。     

地热热泵调峰供暖系统的热力及经济分析

着重分析了地热热泵调峰供暖系统的热力性能和经济性。对两种采暖终端暖气片和风机盘管，分析计算了地热热泵调峰供暖系统的供暖参数和热泵性能参考。对我国目前经济条件下地热热泵调峰供暖的经济性进行了探讨，并与常规地热锅炉调峰供暖和传统锅炉供暖进行了比较。     

地板辐射采暖和风机盘管采暖室内热环境及能耗比较

对地板辐射和风机盘管两种采暖方式进行了实验研究和理论分析，提出了围护结构临界热阻临的概念，推导出了两个采暖系统的热舒适性随围护结构热阻和冷风渗透量波动的变化关系。实验验证了地板辐射采暖既改善了室内热环境又显示较好的节能效果。     

高温地热水供热系统关键技术研究

主要从优化理论的角度出发,分析了深层地热高温水供热系统的几种关键技术设备。即高温热泵、换热器和风机盘管等关键技术的概念、分类、运行条件等进行了研究。以便于科研、设计、运行管理等科技人员决策参考使用。     

低温热水地板辐射采暖系统

结合设计实践，介绍了低温热水地板辐射采暖系统的设计特点，主要性能及构成，分析了低热水地板辐射采暖的优越性，及与其它采暖方式的经济性能比较，指出低温热水地板辐射条件具有广阔的发展空间和推广前景。     

基于火用分析的供暖末端设备节能性研究

探讨了散热器、供暖地板、风机盘管、毛细管辐射平面等4种室内供暖末端设备的采暖特点;阐述了4种采暖设备的传热机理及热舒适性;利用火用分析方法进行能量计算。计算结果显示,毛细管辐射平面空调系统可比低温地板辐射采暖系统节能52.82%。供暖末端设备的节能分析为供暖工程设计提供一定的理论参考。     

太阳能空气集热控制系统的研究

太阳能空气集热采暖系统作为一种简单有效的太阳能应用方式,渐渐引起了世界各国学者的广泛关注。然而,由于太阳能空气采暖的热源是太阳能,建筑室内环境很容易受室外天气影响,这使得建筑的热性能具有不确定性,为了解决上述问题,文中以单片机为控制核心,以温度、太阳辐射照度为输入参数,采用PID方法控制风机启闭及转速,获取最佳的风机运行状态,提高系统的供热效果及效率。     

基于计算机仿真的低温地板辐射采暖系统的节能性分析

介绍了基于空间热网模型的采暖系统的计算机仿真程序，并运用该程序对低温地板辐射采暖和对流采暖两种系统进行计算机仿真，通过对一个采暖日内两种采暖方式下房间的采暖负荷、室内平均空气温度和维护结构内表面温度的动态分析和比较，证明了在维持房间相同热舒适度的情况下，低温地板辐射采暖系统的采暖负荷比对流采暖系统的采暖负荷小，具有节能性。     

低温地板辐射采暖系统中辐射板布置方式的优化

低温地板辐射采暖系统作为一种既节能又舒适的新型采暖方式，国内外对其节能性和节能能力进行了相当多的研究，但对如何进行低温地板辐射采暖系统优化设计的研究很少，本文基于热网模型．利用数值模拟，在等舒适度情况下对不同的辐射板的布置方式(周边布置和中心布置)和辐射板铺设位置的情况下的能耗进行分析，并进一步对如何优化辐射板铺设位置进行了探讨，从而可为低温热水地板辐射采暖系统的优化设计提供参考。     

太阳能地板辐射系统用于夜间采暖时系统性能的实验研究

利用太阳能集热器制得低温热水作为地板辐射采暖系统的热源,是一种清洁、节能、舒适的采暖方式。在南京地区搭建了太阳能地板辐射采暖系统实验台,系统运行策略为白天集热、夜晚采暖,通过实验得到了集热器集热效率、地板进出水温度、室内不同朝向围护结构温度、不同高度的空气温度等参数,最后对系统的性能进行了概括和总结。     

Ash-forming elements in four Scandinavian wood species. Part 1: Summer harvest

Woody biomass in Finland and Sweden comprises mainly four wood species: spruce, pine, birch and aspen. To study the ash, which may cause problems for the combustion device, one tree of each species were cut down and prepared for comparisons with fuel samples. Well-defined samples of wood, bark and foliage were analyzed on 11 ash-forming elements: Si, Al, Fe, Ca, Mg, Mn, Na, K, P, S and Cl. The ash content in the wood tissues (0.2–0.7%) was low compared to the ash content in the bark tissues (1.9–6.4%) and the foliage (2.4–7.7%). The woods’ content of ash-forming elements was consequently low; the highest contents were of Ca (410–1340 ppm) and K (200–1310), followed by Mg (70–290), Mn (15–240) and P (0–350). Present in the wood was also Si (50–190), S (50–200) and Cl (30–110). The bark tissues showed much higher element contents; Ca (4800–19,100 ppm) and K (1600–6400) were the dominating elements, followed by Mg (210–2400), P (210–1200), Mn (110–1100) and S (310–750), but the Cl contents (40–330) were only moderately higher in the bark than in the wood. The young foliage (shoots and deciduous leaves) had the highest K (7100–25,000 ppm), P (1600–5300) and S (1100–2600) contents of all tissues, while the shoots of spruce had the highest Cl contents (820–1360) and its needles the highest Si content (5000–11,300). This paper presented a new approach in fuel characterization: the method excludes the presence of impurities, and focus on different categories of plant tissues. This made it possible to discuss the contents of ash element in a wide spectrum of fuel-types, which are of large importance for the energy production in Finland and Sweden.     

NEXT GENERATION ENGINEERED MATERIALS FOR ULTRA SUPERCRITICAL STEAM TURBINES

正1 ABSTRACT To reduce the effect of global warming on our climate,the levels of CO2emissions should be reduced.One way to do this is to increase the efficiency of electricity production from fossil fuels.This will in turn reduce the amount of CO2emissions for a given power output.Using US practice for efficiency calculations,then a move from a typical US plant running at 37%efficiency to a 760℃/38.5 MPa(1 400/5 580 psi)plant running at 48%efficiency would reduce CO2emissions by 170kg/MW.hr or 25%.     

Aerodynamic performance effects of leading-edge geometry in gas-turbine blades

The purpose of this paper is to illustrate the advantages of the direct surface-curvature distribution blade-design method, originally proposed by Korakianitis, for the leading-edge design of turbine blades, and by extension for other types of airfoil shapes. The leading edge shape is critical in the blade design process, and it is quite difficult to completely control with inverse, semi-inverse or other direct-design methods. The blade-design method is briefly reviewed, and then the effort is concentrated on smoothly blending the leading edge shape (circle or ellipse, etc.) with the main part of the blade surface, in a manner that avoids leading-edge flow-disturbance and flow-separation regions. Specifically in the leading edge region we return to the second-order (parabolic) construction line coupled with a revised smoothing equation between the leading-edge shape and the main part of the blade. The Hodson–Dominy blade has been used as an example to show the ability of this blade-design method to remove leading-edge separation bubbles in gas turbine blades and other airfoil shapes that have very sharp changes in curvature near the leading edge. An additional gas turbine blade example has been used to illustrate the ability of this method to design leading edge shapes that avoid leading-edge separation bubbles at off-design conditions. This gas turbine blade example has inlet flow angle 0°, outlet flow angle −64.3°, and tangential lift coefficient 1.045, in a region of parameters where the leading edge shape is critical for the overall blade performance. Computed results at incidences of −10°,   −5°,   +5°,   +10° are used to illustrate the complete removal of leading edge flow-disturbance regions, thus minimizing the possibility of leading-edge separation bubbles, while concurrently minimizing the stagnation pressure drop from inlet to outlet. These results using two difficult example cases of leading edge geometries illustrate the superiority and utility of this blade-design method when compared with other direct or inverse blade-design methods.     

Hydrogen production by steam-gasification of carbonaceous materials using concentrated solar energy – V. Reactor modeling,optimization, and scale-up

A chemical reactor for the steam-gasification of carbonaceous particles (e.g. coal, coke) is considered for using concentrated solar radiation as the energy source of high-temperature process heat. A two-phase reactor model that couples radiative, convective, and conductive heat transfer to the chemical kinetics is applied to optimize the reactor geometrical configuration and operational parameters (feedstock's initial particle size, feeding rates, and solar power input) for maximum reaction extent and solar-to-chemical energy conversion efficiency of a 5 kW prototype reactor and its scale-up to 300 kW. For the 300 kW reactor, complete reaction extent is predicted for an initial feedstock particle size up to 35 μm at residence times of less than 10 s and peak temperatures of 1818 K, yielding high-quality syngas with a calorific content that has been solar-upgraded by 19% over that of the petcoke gasified.     

Contents in Volume 23,2014

<正>~~     

汽轮机数字电液调节系统挂闸异常的技术完善

分析了200MW汽轮机数字电液调节系统在运行中存在的挂闸异常问题,采取了相应的技术处理措施,且运行实践效果良好。     

新型高压共轨ECU升压模块的数字化开发与优化

为了提高喷油器电磁阀的响应速率,提出了一种基于CPLD(复杂可编程逻辑器件)应用于高压共轨ECU的数字升压模块。鉴于该升压电路结构参数多,其升压电压的恢复响应要求高等特征,基于Pspice建立了升压电路的仿真模型,研究了不同电路参数下升压模块的输出特性,全面优化了该升压模块的性能。结果显示,该升压模块的最大转换效率可以达90%以上。在柴油发动机上对ECU的试验表明,升压电压最大波动不超过10%,其恢复时间仅为1.3ms,功率管最大温升仅为41℃,满足整机运行范围内ECU的需求。     

Assessment methods of material ageing using Sdobyrev''s creep rupture model

The physical aspects of the activation energy, in higher and high temperatures, of the metal creep process were examined. The research results of creep-rupture in a uniaxial stress state and the criterion of creep-rupture in biaxial stress states, at two temperatures, are then presented. For these studies creep-rupture, taking case iron as an example the energy and pseudoenergy activation was determined. For complex stress states the criterion of creep-rupture was taken to be Sdobyrev's, i.e. σ_red = σ₁ β + (1 − β)σ_i, where: σ₁-maximal principal stress, σ_i-stress intensity, β-material constant (at variable temperature β = β(T)). The methods of assessment of the material ageing grade are given in percentages of ageing of new material in the following mechanical properties: 1) creep strength in uniaxial stress state, 2) activation energy in uniaxial stress state, 3) criterion creep strength in complex stress states, 4) activation pseudoenergy in complex stress states. The methods 1) and 3) are the relatively simplest because they result from experimental investigations only at nominal temperature of the structure work, however, for methods 2) and 4) it is necessary to perform the experimental investigations at least at two temperatures.     

Production of hydrogen from sewage biosolids in a continuously fed bioreactor: Effect of hydraulic retention time and sparging

Hydrogen was produced from primary sewage biosolids via mesophilic anaerobic fermentation in a continuously fed bioreactor. Prior to fermentation the sewage biosolids were heated to 70 °C for 1 h to inactivate methanogens and during fermentation a cellulose degrading enzyme was added to improve substrate availability. Hydraulic retention times (HRT) of 18, 24, 36 and 48 h were evaluated for the duration of hydrogen production. Without sparging a hydraulic retention time of 24 h resulted in the longest period of hydrogen production (3 days), during which a hydrogen yield of 21.9 L H₂ kg⁻¹ VS added to the bioreactor was achieved. Methods of preventing the decline of hydrogen production during continuous fermentation were evaluated. Of the techniques evaluated using nitrogen gas to sparge the bioreactor contents proved to be more effective than flushing just the headspace of the bioreactor. Sparging at 0.06 L L min⁻¹ successfully prevented a decline in hydrogen production and resulted in a yield of 27.0  L H₂ kg⁻¹ VS added, over a period of greater than 12 days or 12 HRT. The use of sparging also delayed the build up of acetic acid in the bioreactor, suggesting that it serves to inhibit homoacetogenesis and thus maintain hydrogen production.     

Trace metal chemistry and silicification of microorganisms in geothermal sinter, Taupo Volcanic Zone, New Zealand

As part of a pilot study investigating the role of microorganisms in the immobilisation of As, Sb, B, Tl and Hg, the inorganic geochemistry of seven different active sinter deposits and their contact fluids were characterised. A comprehensive series of sequential extractions for a suite of trace elements was carried out on siliceous sinter and a mixed silica-carbonate sinter. The extractions showed whether metals were loosely exchangeable or bound to carbonate, oxide, organic or crystalline fractions. Hyperthermophilic microbial communities associated with sinters deposited from high temperature (92–94°C) fluids at a variety of geothermal sources were investigated using SEM. The rapidity and style of silicification of the hyperthermophiles can be correlated with the dissolved silica content of the fluid. Although high concentrations of Hg and Tl were found associated with the organic fraction of the sinters, there was no evidence to suggest that any of the heavy metals were associated preferentially with the hyperthermophiles at the high temperature (92–94°C) ends of the terrestrial thermal spring ecosystems studied.