Pure and Saturated Red Electroluminescent Polyfluorenes with Dopant/Host System and PLED Efficiency/Color Purity Trade‐Offs

Three kinds of red electroluminescent (EL) polymers based on polyfluorene as blue host and 2,1,3‐benzothiadiazole derivatives with different emission wavelengths as red dopant units on the side chain are designed and synthesized. The influence of the photoluminescence (PL) efficiencies and emission wavelengths of red dopants on the EL efficiencies and color purities of the resulting polyfluorene copolymers of dopant/host system is investigated by adjusting the electron donating ability of the donor units in D‐π‐A‐D typed 2,1,3‐benzothiadiazole derivatives. The devices of these red‐emitting polymers realize remarkable EL efficiency/color purity trade‐offs. The single‐layer devices with the configuration of ITO/PEDOT:PSS/Polymer/Ca/Al show pure red emission at 624 nm with a luminous efficiency of 3.83 cd A^?1 and CIE of (0.63, 0.35) for PFR1, saturated red emission at 636 nm with a luminous efficiency of 2.29 cd A^?1 and CIE of (0.64, 0.33) for PFR2, respectively. By introduction of an additional electron injection layer PF‐EP(Ethanol soluble phosphonate‐functionalized polyfluorene), high performance pure and saturated red emission two‐layer devices (ITO/PEDOT:PSS/Polymer/PF‐EP/LiF/Al) were achieved with maximum luminous efficiencies of 5.50 cd A^?1 and CIE of (0.62, 0.35) for PFR1, 3.10 cd A^?1 and CIE of (0.63, 0.33) for PFR2, respectively, which are the best results for pure and saturated fluorescent red EL polymers reported so far.     

Stable Inverted Polymer/Fullerene Solar Cells Using a Cationic Polythiophene Modified PEDOT:PSS Cathodic Interface

A cationic and water‐soluble polythiophene [poly[3‐(6‐pyridiniumylhexyl)thiophene bromide] (P3PHT⁺Br^?)] is synthesized and used in combination with anionic poly(3,4‐ethylenedioxythiophene):poly(p‐styrenesulfonate) (PEDOT:PSS)^? to produce hybrid coatings on indium tin oxide (ITO). Two coating strategies are established: i) electrostatic layer‐by‐layer assembly with colloidal suspensions of (PEDOT:PSS)^?, and ii) modification of an electrochemically prepared (PEDOT:PSS)^? film on ITO. The coatings are found to modify the work function of ITO such that it could act as a cathode in inverted 2,5‐diyl‐poly(3‐hexylthiophene) (P3HT)/[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) polymer photovoltaic cells. The interfacial modifier created from the layer‐by‐layer assembly route is used to produce efficient inverted organic photovoltaic devices (power conversion efficiency ～2%) with significant long‐term stability in excess of 500 h.     

Efficient White‐Electrophosphorescent Devices Based on a Single Polyfluorene Copolymer

An efficient white‐light‐emitting polymer ( W3 ) is realized by covalently attaching a green fluorophore and a red phosphor into the backbone and the side chains, respectively, of polyfluorene at a concentration of 0.04 mol %. In addition, charge‐transporting pendant units are included to improve carrier injection and transport. White‐electrophosphorescent devices with the structure ITO/PEDOT:PSS/ W3 /CsF/Al (ITO: indium tin oxide; PEDOT:PSS: poly(styrenesulfonate)‐doped poly(3,4‐ethylenedioxythiophene)) exhibit a low turn‐on voltage of 2.8 V and a luminance of ca. 10³ cd m^–2 at below 6 V. The peak luminance and power‐conversion efficiencies are 8.2 cd A^–1 and 7.2 lm W^–1, respectively. Furthermore, the device shows relatively stable white emission: the Commission Internationale d'Éclairage (CIE) chromaticity coordinates of the devices change only slightly from (0.35,0.38) at 10 mA cm^–2 to (0.33,0.36) at 100 mA cm^–2, with an almost constant color render index (CRI) value of 82 at all measured current densities.     

Efficient Light‐Emitting Electrochemical Cells (LECs) Based on Ionic Iridium(III) Complexes with 1,3,4‐Oxadiazole Ligands

Eight new iridium(III) complexes 1‐8 , with 1,3,4‐oxadiazole (OXD) derivatives as the cyclometalated C^N ligand and/or the ancillary N^N ligands are synthesized and their electrochemical, photophysical, and solid‐state light‐emitting electrochemical cell (LEC) properties are investigated. Complexes 1 , 2 , 7 and 8 are additionally characterized by single crystal X‐ray diffraction. LECs based on complexes 1‐8 are fabricated with a structure indium tin oxide (ITO)/poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)/cationic iridium complex:ionic liquid/Al. LECs of complexes 1 – 6 with OXD derivatives as the cyclometalated ligands and as the ancillary ligand show yellow luminescence (λ_max = 552–564 nm). LECs of complexes 7 and 8 with cyclometalated C^N phenylpyridine ligands and an ancillary N^N OXD ligand show red emission (λ_max 616–624 nm). Using complex 7 external quantum efficiency (EQE) values of >10% are obtained for devices (210 nm emission layer) at 3.5 V. For thinner devices (70 nm) high brightness is achieved: red emission for 7 (8528 cd m^?2 at 10 V) and yellow emission for 1 (3125 cd m^?2 at 14 V).     

Screen‐Printed Poly(3,4‐Ethylenedioxythiophene):Poly(Styrenesulfonate) Grids as ITO‐Free Anodes for Flexible Organic Light‐Emitting Diodes

Poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT: PSS) grids have been successfully constructed by roll‐to‐roll compatible screen‐printing techniques and have been used as indium tin oxide (ITO)‐free anodes for flexible organic light‐emitting diodes (OLEDs). The grid‐type transparent conductive electrodes (TCEs) can adopt thicker PEDOT: PSS grid lines to ensure the conductivity, while the mesh‐like grid structure can play an important role to maintain high optical transparency. By adjusting grid periods, grid thickness and treatment of organic additives, PEDOT: PSS TCEs with high optical transparency, low sheet resistance, and excellent mechanical flexibility have been achieved. Using the screen‐printed PEDOT: PSS grids as the anodes, ITO‐free OLEDs achieved peak current efficiency of 3.40 cd A^?1 at the current density of 10 mA cm^?2, which are 1.56 times better than the devices with ITO glass as the anodes. The improved efficiency is attributed to the light extraction effect and improved transparency by the grid structure. The superior optoelectronic performances of OLEDs based on flexible screen‐printed PEDOT: PSS grid anodes suggest their great prospects as ITO‐free anodes for flexible and wearable electronic applications.     

Solution‐Processed Thermally Activated Delayed Fluorescent OLED with High EQE as 31% Using High Triplet Energy Crosslinkable Hole Transport Materials

Solution‐processed organic light‐emitting diodes (OLEDs) with thermally activated delayed fluorescent (TADF) material as emitter have attracted much attention because of their low cost and high performance. However, exciton quench at the interface between the hole injection layer, poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS), and emitting layer (EML) in devices can lead to low device performance. Here, a novel high triplet energy (2.89 eV) and crosslinkable hole‐transporting material grafted with oxetane groups, N,N‐bis(4‐(6‐((3‐ethyloxetan‐3‐yl)methoxy)hexyloxy)phenyl)‐3,5‐di(9H‐carbazol‐9‐yl)benzenamine (Oxe‐DCDPA)), as crosslinked hole transport layer (HTL) into the interface of PEDOT:PSS layer and EML is proposed for prevention of exciton quenching, and among the reported devices with single HTL in solution‐processed TADF‐OLED, the highest external quantum efficiency (EQE)/luminous efficiency (η_L) of 26.1%/94.8 cd A^?1 and 24.0%/74.0 cd A^?1 are achieved for green emission (DACT‐II as emitter) and bluish‐green emission (DMAC‐TRZ as emitter), respectively. Further improvement, using double HTLs, composed of N,N′‐bis(4‐(6‐((3‐ethyloxetan‐3‐yl)methoxy))‐hexylphenyl)‐N,N′‐diphenyl‐4,4′‐diamine with high hole mobility and Oxe‐DCDPA with high triplet energy, leads to the highest EQE/η_L of 30.8%/111.9 cd A^?1 and 27.2%/83.8 cd A^?1 for green emission and bluish‐green emission, respectively. These two devices show the high maximum brightness of 81 100 and 70 000 cd m^?2, respectively.     

Multifunctional Fluorene‐Based Oligomers with Novel Spiro‐Annulated Triarylamine: Efficient,Stable Deep‐Blue Electroluminescence,Good Hole Injection,and Transporting Materials with Very High Tg

A series of fluorene‐based oligomers with novel spiro‐annulated triarylamine structures, namely DFSTPA, TFSTPA, and TFSDTC, are synthesized by a Suzuki cross‐coupling reaction. The spiro‐configuration molecular structures lead to very high glass transition temperatures (197–253 °C) and weak intermolecular interactions, and consequently the structures retain good morphological stability and high fluorescence quantum efficiencies(0.69–0.98). This molecular design simultaneously solves the spectral stability problems and hole‐injection and transport issues for fluorene‐based blue‐light‐emitting materials. Simple double‐layer electroluminescence (EL) devices with a configuration of ITO/TFSTPA (device A) or TFSDTC (device B)/ TPBI/LiF/Al, where TFSTPA and TFSDTC serve as hole‐transporting blue‐light‐emitting materials, show a deep‐blue emission with a peak around 432 nm, and CIE coordinates of (0.17, 0.12) for TFSTPA and (0.16, 0.07) for TFSDTC, respectively, which are very close to the National Television System Committee (NTSC) standard for blue (0.15, 0.07). The maximum current efficiency/external quantum efficiencies are 1.63 cd A^?1/1.6% for device A and 1.91 cd A^?1/2.7% for device B, respectively. In addition, a device with the structure ITO/DFSTPA/Alq₃/LiF/Al, where DFSTPA acts as both the hole‐injection and ‐transporting material, is shown to achieve a good performance, with a maximum luminance of 14 047 cd m^?2, and a maximum current efficiency of 5.56 cd A^?1. These values are significantly higher than those of devices based on commonly usedN,N′‐di(1‐naphthyl)‐N,N′‐diphenyl‐[1,1′‐biphenyl]‐4,4′‐diamine (NPB) as the hole‐transporting layer (11 738 cd m^?2 and 3.97 cd A^?1) under identical device conditions.     

Synthesis, Characterization, and Electroluminescent Properties of Pyridinylene Vinylene-Modified Phenylene Vinylene Copolymers

Two random copolymers of phenylene vinylene and pyridinylene vinylene, ED-co-PyV-PPV and EM-co-PyV-PPV, were synthesized according to the Gilch route. The polymers possess good solubility in common solvents, and high thermal stability with 5% weight loss temperature above 378°C. The weight-average molecular weight (M _w) and polydispersity index of ED-co-PyV-PPV and EM-co-PyV-PPV are 3.12?×?10⁵ and 1.40, and 2.30?×?10⁵ and 1.96, respectively. Single-layer polymer light-emitting diodes (PLEDs) with indium tin oxide (ITO)/poly(3,4-ethylenedioxythiophene) (PEDOT):poly(styrenesulfonate) (PSS)/polymer/Ca/Al configuration were fabricated. The turn-on voltages of the PLEDs based on ED-co-PyV-PPV and EM-co-PyV-PPV were approximately 4.0?V and 2.8?V, respectively. The ED-co-PyV-PPV PLED device exhibited the maximum luminance of ca. 4380?cd/m² with maximum electroluminescence (EL) efficiency of 6.35?cd/A.     

Fluorene‐Based Asymmetric Bipolar Universal Hosts for White Organic Light Emitting Devices

Two new bipolar host molecules composed of hole‐transporting carbazole and electron‐transporting cyano ( CzFCN ) or oxadiazole ( CzFOxa )‐substituted fluorenes are synthesized and characterized. The non‐conjugated connections, via an sp³‐hybridized carbon, effectively block the electronic interactions between electron‐donating and ‐accepting moieties, giving CzFCN and CzFOxa bipolar charge transport features with balanced mobilities (10^?5 to 10^?6 cm² V^?1 s^?1). The meta–meta configuration of the fluorene‐based acceptors allows the bipolar hosts to retain relatively high triplet energies [E_T = 2.70 eV ( CzFOxa ) and 2. 86 eV ( CzFCN )], which are sufficiently high for hosting blue phosphor. Using a common device structure – ITO/PEDOT:PSS/DTAF/TCTA/host:10% dopants (from blue to red)/DPPS/LiF/Al – highly efficient electrophosphorescent devices are successfully achieved. CzFCN ‐based devices demonstrate better performance characteristics, with maximum η_ext of 15.1%, 17.9%, 17.4%, 18%, and 20% for blue (FIrpic), green [(PPy)₂Ir(acac)], yellowish‐green [m‐(Tpm)₂Ir(acac)], yellow [(Bt)₂Ir(acac)], and red [Os(bpftz)₂(PPhMe₂)₂, OS1], respectively. In addition, combining yellowish‐green m‐(Tpm)₂Ir(acac) with a blue emitter (FIrpic) and a red emitter (OS1) within a single emitting layer hosted by bipolar CzFCN , three‐color electrophosphorescent WOLEDs with high efficiencies (17.3%, 33.4 cd A^?1, 30 lm W ^?1), high color stability, and high color‐rendering index (CRI) of 89.7 can also be realized.     

Paper‐Based Electrochromic Devices Enabled by Nanocellulose‐Coated Substrates

As environmental considerations for both the processing and disposal of electronic devices become increasingly important, the ability to replace plastic and glass substrates with bioderived and biodegradable materials remains a major technological goal. Here, the use of cellulose nanofiber‐coated paper is explored as an environmentally benign substrate for preparing low‐resistance (460 Ω sq^?1), colorless (a* = ?2.3, b* = ?2.7) printed poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) electrodes. The PEDOT:PSS/paper electrodes support the reversible oxidation of three electrochromic polymers (ECPs) (cyan, magenta, and yellow), affording the possibility for fully printed, color displays on paper. Lateral electrochromic devices (ECDs) incorporating an ion gel electrolyte are demonstrated where a magenta‐to‐colorless device achieves a color contrast (ΔE*) of 56 owing to a highly color‐neutral bleached state of the ECP (a* = ?0.5, b* = 2.9). Black‐to‐colorless devices achieve ΔE* = 29 and are able to retain 86% of their color contrast after 9000 switches. The switching times of these lateral devices are quantified through colorimetric image analysis which shows comparable performance for devices constructed on paper as devices using ITO/glass electrodes (10 Ω sq^?1). The paper ECDs are then combusted in air leaving 3% of the initial mass at 600 °C, highlighting this approach as a promising route toward disposable displays.     

Optimizing OLED Efficacy of 2,7‐Diconjugated 9,9‐Dialkylfluorenes by Variation of Periphery Substitution and Conjugation Length

The photoluminescence (PL) and electroluminescence (EL) of four 2,7‐bis(phenylethenyl)fluorenes (OFPVs) and two 2,7‐diphenylfluorenes (OFPhs) are compared to evaluate effects of nonconjugating peripheral substitution and conjugation length on their EL emissions. The OFPVs exhibit very similar PL spectra with 460–480 nm emission maxima but show large variation in the organic light‐emitting diode (OLED) efficacy: from a material that does not give persistent emission in test OLEDs (9,9‐diheptyl substitution on the fluorene ring) to materials with luminance efficiencies of 0.5 cd A^–1 and greater (9,9‐diethyl substitution on the fluorene ring, methoxy and methoxy/heptyloxy substituents on the phenylethenyl rings). The best OFPV in an ITO/PEDOT:PSS/(emitter)/Ca–Al (ITO: indium tin oxide; PEDOT: poly(ethylenedioxythiophene); PSS: poly(styrene sulfonate)) OLED configuration has 9,9‐diethyl substitution and terminal heptyloxy substitution (maximum luminance of 1500 cd m^–2 at 12 V). Unlike the OFPVs, the neat OFPhs show not only EL at the desired blue output of ca. 400–410 nm emission maxima but also an undesired green emission component at 500–550 nm. Blending the OFPhs with poly(methyl methacrylate) eliminates the long‐wavelength component when the emitter load is 10–25 %, but the OFPh luminance efficiencies, turn‐on voltages, and maximum luminance tend to be poorer than those of the OFPVs. The deficiencies of the OFPhs appear to be attributable to thermal degradation and oxidative reactivity, although solid‐state annealing and a nonoptimal bandgap match to the OLED device configuration may also contribute.     

Efficient Polymer Electrophosphorescent Devices with Interfacial Layers

It is shown that several polymers can form insoluble interfacial layers on a poly(ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) layer after annealing of the double‐layer structure. The thickness of the interlayer is dependent on the characteristics of the underlying PEDOT:PSS and the molecular weight of the polymers. It is further shown that the electronic structures of the interlayer polymers have a significant effect on the properties of red‐light‐emitting polymer‐based electrophosphorescent devices. Upon increasing the highest occupied molecular orbital and lowest unoccupied molecular orbital positions, a significant increase in current density and device efficiency is observed. This is attributed to efficient blocking of electrons in combination with direct injection of holes from the interlayer to the phosphorescent dye. Upon proper choice of the interlayer polymer, efficient red, polymer‐based electrophosphorescent devices with a peak luminance efficiency of 5.5 cd A^–1 (external quantum efficiency = 6 %) and a maximum power‐conversion efficiency of 5 lm W^–1 can be realized.     

Fine Control of Perovskite Crystallization and Reducing Luminescence Quenching Using Self‐Doped Polyaniline Hole Injection Layer for Efficient Perovskite Light‐Emitting Diodes

Organic–inorganic hybrid perovskites (OHPs) are promising emitters for light‐emitting diodes (LEDs) due to the high color purity, low cost, and simple synthesis. However, the electroluminescent efficiency of polycrystalline OHP LEDs (PeLEDs) is often limited by poor surface morphology, small exciton binding energy, and long exciton diffusion length of large‐grain OHP films caused by uncontrolled crystallization. Here, crystallization of methylammonium lead bromide (MAPbBr₃) is finely controlled by using a polar solvent‐soluble self‐doped conducting polymer, poly(styrenesulfonate)‐grafted polyaniline (PSS‐g‐PANI), as a hole injection layer (HIL) to induce granular structure, which makes charge carriers spatially confined more effectively than columnar structure induced by the conventional poly(3,4‐ethylenedioythiphene):polystyrenesulfonate (PEDOT:PSS). Moreover, lower acidity of PSS‐g‐PANI than PEDOT:PSS reduces indium tin oxide (ITO) etching, which releases metallic In species that cause exciton quenching. Finally, doubled device efficiency of 14.3 cd A^‐1 is achieved for PSS‐g‐PANI‐based polycrystalline MAPbBr₃ PeLEDs compared to that for PEDOT:PSS‐based PeLEDs (7.07 cd A^‐1). Furthermore, PSS‐g‐PANI demonstrates high efficiency of 37.6 cd A^‐1 in formamidinium lead bromide nanoparticle LEDs. The results provide an avenue to both control the crystallization kinetics and reduce the migration of In released from ITO by forming OIP films favorable for more radiative luminescence using the polar solvent‐soluble and low‐acidity polymeric HIL.     

Anode Interfacial Tuning via Electron‐Blocking/Hole‐Transport Layers and Indium Tin Oxide Surface Treatment in Bulk‐Heterojunction Organic Photovoltaic Cells

The effects of anode/active layer interface modification in bulk‐heterojunction organic photovoltaic (OPV) cells is investigated using poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) and/or a hole‐transporting/electron‐blocking blend of 4,4′‐bis[(p‐trichlorosilylpropylphenyl)‐phenylamino]biphenyl (TPDSi₂) and poly[9,9‐dioctylfluorene‐co‐N‐[4‐(3‐methylpropyl)]‐diphenylamine] (TFB) as interfacial layers (IFLs). Current–voltage data in the dark and AM1.5G light show that the TPDSi₂:TFB IFL yields MDMO‐PPV:PCBM OPVs with substantially increased open‐circuit voltage (V_oc), power conversion efficiency, and thermal stability versus devices having no IFL or PEDOT:PSS. Using PEDOT:PSS and TPDSi₂:TFB together in the same cell greatly reduces dark current and produces the highest V_oc (0.91 V) by combining the electron‐blocking effects of both layers. ITO anode pre‐treatment was investigated by X‐ray photoelectron spectroscopy to understand why oxygen plasma, UV ozone, and solvent cleaning markedly affect cell response in combination with each IFL. O₂ plasma and UV ozone treatment most effectively clean the ITO surface and are found most effective in preparing the surface for PEDOT:PSS deposition; UV ozone produces optimum solar cells with the TPDSi₂:TFB IFL. Solvent cleaning leaves significant residual carbon contamination on the ITO and is best followed by O₂ plasma or UV ozone treatment.     

Highly Conductive Poly(3,4‐ethylenedioxythiophene):Poly (styrenesulfonate) Films Using 1‐Ethyl‐3‐methylimidazolium Tetracyanoborate Ionic Liquid

Highly conductive poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) films are obtained using ionic liquids as additives. Upon adding 1‐ethyl‐3‐methylimidazolium tetracyanoborate (EMIM TCB) to the conducting polymer, the conductivity increases to 2084 S cm^?1; this is attributed to the phase separation of PSS leading to a structural change in the film. A comparative study with 1‐butyl‐3‐methyl imidazolium tetrafluoroborate (BMIM BF₄) shows that EMIM TCB gives higher conductivity and transmittance and can be regarded as one of the most promising additives for the preparation of indium tin oxide (ITO)‐free organic devices using PEDOT:PSS/EMIM TCB as electrodes.     

Unexpected Propeller‐Like Hexakis(fluoren‐2‐yl)benzene Cores for Six‐Arm Star‐Shaped Oligofluorenes: Highly Efficient Deep‐Blue Fluorescent Emitters and Good Hole‐Transporting Materials

Grafting six fluorene units to a benzene ring generates a new highly twisted core of hexakis(fluoren‐2‐yl)benzene. Based on the new core, six‐arm star‐shaped oligofluorenes from the first generation T1 to third generation T3 are constructed. Their thermal, photophysical, and electrochemical properties are studied, and the relationship between the structures and properties is discussed. Simple double‐layer electroluminescence (EL) devices using T1–T3 as non‐doped solution‐processed emitters display deep‐blue emissions with Commission Internationale de l'Eclairage (CIE) coordinates of (0.17, 0.08) for T1 , (0.16, 0.08) for T2 , and (0.16, 0.07) for T3 . These devices exhibit excellent performance, with maximum current efficiency of up to 5.4 cd A^?1, and maximum external quantum efficiency of up to 6.8%, which is the highest efficiency for non‐doped solution‐processed deep‐blue organic light‐emitting diodes (OLEDs) based on starburst oligofluorenes, and is even comparable with other solution‐processed deep‐blue fluorescent OLEDs. Furthermore, T2‐ and T3‐ based devices show striking blue EL color stability independent of driving voltage. In addition, using T0–T3 as hole‐transporting materials, the devices of indium tin oxide (ITO)/poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonic acid) (PEDOT:PSS)/ T0–T3 /tris(8‐hydroxyquinolinato)aluminium (Alq₃)/LiF/Al achieve maximum current efficiencies of 5.51–6.62 cd A^?1, which are among the highest for hole‐transporting materials in identical device structure.     

High‐Efficiency and Stable Quantum Dot Light‐Emitting Diodes Enabled by a Solution‐Processed Metal‐Doped Nickel Oxide Hole Injection Interfacial Layer

Stabilization is one critical issue that needs to be improved for future application of colloidal quantum dot (QD)‐based light‐emitting diodes (QLEDs). This study reports highly efficient and stable QLEDs based on solution‐processsed, metal‐doped nickel oxide films as hole injection layer (HIL). Several kinds of metal dopants (Li, Mg, and Cu) are introduced to improve the hole injection capability of NiO films. The resulting device with Cu:NiO HIL exhibits superior performance compared to the state‐of‐the‐art poly(3,4‐ethylenedioxythiophene):poly(styrene‐sulfonate) (PEDOT:PSS)‐based QLEDs, with a maximum current efficiency and external quantum efficiency of 45.7 cd A^?1 and 10.5%, respectively. These are the highest values reported so far for QLEDs with PEDOT:PSS‐free normal structure. Meanwhile, the resulting QLED shows a half‐life time of 87 h at an initial luminance of 5000 cd m^?2, almost fourfold longer than that of the PEDOT:PSS‐based device.     

Influence of aluminium electrode preparation on PCE values of polymeric solar cells based on P3HT and PCBM

The main goal of the paper was investigation of influence of aluminum electrode preparation via thermal evaporation (TE) and the magnetron sputtering (MS) on power conversion efficiency (PCE) of polymeric solar cells. The photovoltaic properties of such three kinds devices based on poly(3-hexylthiophene-2,5-diyl) (P3HT) as ITO/P3HT/Al, ITO/P3HT:PCBM (1:1, w/w)/Al and ITO/PEDOT:PSS/P3HT:PCBM (1:1, w/w)/Al were investigated. For the constructed devices impedance spectroscopy were analyzed. For devices lack of PEDOT:PSS layer or lack of PCBM, photovoltaic parameters were very low and similar to the parameters obtained for device with Al electrode prepared by magnetron sputtering. The devices comprising PEDOT:PSS with P3HT:PCBM showed the best photovoltaic parameters such as a V_OC of 0.60 V, J_SC of 4.61 mA/cm², FF of 0.21, and PCE of 5.7 × 10^?1%.     

Highly Conductive and Transparent PEDOT:PSS Films with a Fluorosurfactant for Stretchable and Flexible Transparent Electrodes

Highly conductive and transparent poly‐(3,4‐ethylenedioxythiophene):poly(styrenesulfonic acid) (PEDOT:PSS) films, incorporating a fluorosurfactant as an additive, have been prepared for stretchable and transparent electrodes. The fluorosurfactant‐treated PEDOT:PSS films show a 35% improvement in sheet resistance (R_s) compared to untreated films. In addition, the fluorosurfactant renders PEDOT:PSS solutions amenable for deposition on hydrophobic surfaces, including pre‐deposited, annealed films of PEDOT:PSS (enabling the deposition of thick, highly conductive, multilayer films) and stretchable poly(dimethylsiloxane) (PDMS) substrates (enabling stretchable electronics). Four‐layer PEDOT:PSS films have an R_s of 46 Ω per square with 82% transmittance (at 550 nm). These films, deposited on a pre‐strained PDMS substrate and buckled, are shown to be reversibly stretchable, with no change to R_s, during the course of over 5000 cycles of 0 to 10% strain. Using the multilayer PEDOT:PSS films as anodes, indium tin oxide (ITO)‐free organic photovoltaics are prepared and shown to have power conversion efficiencies comparable to that of devices with ITO as the anode. These results show that these highly conductive PEDOT:PSS films can not only be used as transparent electrodes in novel devices (where ITO cannot be used), such as stretchable OPVs, but also have the potential to replace ITO in conventional devices.     

Thermoelectric Performance Enhancement of Poly(3,4-ethylenedioxythiophene):Poly(styrenesulfonate) Composite Films by Addition of Dimethyl Sulfoxide and Urea

Significant enhancement of thermoelectric (TE) performance was observed for free-standing poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT: PSS) composite films obtained from a PEDOT:PSS aqueous solution by simultaneous addition of dimethyl sulfoxide (DMSO) and different concentrations of urea. The electrical conductivity was enhanced from 8.16?S?cm^?1 to over 400?S?cm^?1, and the maximum Seebeck coefficient reached a value of 18.81???V?K^?1 at room temperature. The power factor of the PEDOT:PSS composite films reached 8.81???W?m^?1?K^?2. The highest thermoelectric figure of merit (ZT) in this study was 0.024 at room temperature, which is at least one order of magnitude higher than most polymers and bulk Si. These results indicate that the obtained composite films are a promising thermoelectric material for applications in thermoelectric refrigeration and thermoelectric microgeneration.