Inkjet‐Printed Organic Electrodes for Bottom‐Contact Organic Field‐Effect Transistors

A graphite thin film was investigated as the drain and source electrodes for bottom‐contact organic field‐effect transistors (BC OFETs). Highly conducting electrodes (10² S cm^?1) at room temperature were obtained from pyrolyzed poly(l,3,4‐oxadiazole) (PPOD) thin films that were prepatterned with a low‐cost inkjet printing method. Compared to the devices with traditional Au electrodes, the BC OFETs showed rather high performances when using these source/drain electrodes without any further modification. Being based on a graphite‐like material these electrodes possess excellent compatibility and proper energy matching with both p‐ and n‐type organic semiconductors, which results in an improved electrode/organic‐layer contact and homogeneous morphology of the organic semiconductors in the conducting channel, and finally a significant reduction of the contact resistance and enhancement of the charge‐carrier mobility of the devices is displayed. This work demonstrates that with the advantages of low‐cost, high‐performance, and printability, PPOD could serve as an excellent electrode material for BC OFETs.     

Tailoring Morphology and Structure of Inkjet‐Printed Liquid‐Crystalline Semiconductor/Insulating Polymer Blends for High‐Stability Organic Transistors

Inkjet printing of semiconducting polymers is desirable for realizing low‐cost, large‐area printed electronics. However, sequential inkjet printing methods often suffer from nozzle clogging because the solubility of semiconducting polymers in organic solvents is limited. Here, it is demonstrated that the addition of an insulating polymer to a semiconducting polymer ink greatly enhances the solubility and stability of the ink, leading to the stable ejection of ink droplets. This bicomponent blend comprising a liquid‐crystalline semiconducting copolymer, poly(didodecylquaterthiophene‐alt‐didodecylbithiazole) (PQTBTz‐C12), and an insulating commodity polymer, polystyrene, is extremely useful as a semiconducting layer in organic field‐effect transistors (OFETs), providing fine control over the phase‐separated morphology and structure of the inkjet‐printed film. Tailoring the solubility‐induced phase separation of the two components leads to a bilayer structure consisting of a polystyrene layer on the top and a highly crystalline PQTBTz‐C12 layer on the bottom. The blend film is used as the semiconducting layer in OFETs, reducing the semiconductor content to several tens of pictograms in a single device without degrading the device performance. Furthermore, OFETs based on the PQTBTz‐C12/polystyrene film exhibit much greater environmental and electrical stabilities compared to the films prepared from homo PQTBTz‐C12, mainly due to the self‐encapsulated structure of the blend film.     

Nonvolatile Ferroelectric P(VDF‐TrFE) Memory Transistors Based on Inkjet‐Printed Organic Semiconductor

Nonvolatile ferroelectric poly(vinylidene fluoride‐co‐trifluoroethylene) memory based on an organic thin‐film transistor with inkjet‐printed dodecyl‐substituted thienylenevinylene‐thiophene copolymer (PC12TV12T) as the active layer is developed. The memory window is 4.5 V with a gate voltage sweep of ?12.5 V to 12.5 V. The field effect mobility, on/off ratio, and gate leakage current are 0.1 cm²/Vs, 10⁵, and 10^?10 A, respectively. Although the retention behaviors should be improved and optimized, the obtained characteristics are very promising for future flexible electronics.     

High‐Performance Top‐Gated Organic Field‐Effect Transistor Memory using Electrets for Monolithic Printed Flexible NAND Flash Memory

High‐performance top‐gated organic field‐effect transistor (OFET) memory devices using electrets and their applications to flexible printed organic NAND flash are reported. The OFETs based on an inkjet‐printed p‐type polymer semiconductor with efficiently chargeable dielectric poly(2‐vinylnaphthalene) (PVN) and high‐k blocking gate dielectric poly(vinylidenefluoride‐trifluoroethylene) (P(VDF‐TrFE)) shows excellent non‐volatile memory characteristics. The superior memory characteristics originate mainly from reversible charge trapping and detrapping in the PVN electret layer efficiently in low‐k/high‐k bilayered dielectrics. A strategy is devised for the successful development of monolithically inkjet‐printed flexible organic NAND flash memory through the proper selection of the polymer electrets (PVN or PS), where PVN/‐ and PS/P(VDF‐TrFE) devices are used as non‐volatile memory cells and ground‐ and bit‐line select transistors, respectively. Electrical simulations reveal that the flexible printed organic NAND flash can be possible to program, read, and erase all memory cells in the memory array repeatedly without affecting the non‐selected memory cells.     

An Inkjet‐Printed Field‐Effect Transistor for Label‐Free Biosensing

A flexible, biological field‐effect transistor (BioFET) for use in biosensing is reported. The BioFET is based on an organic thin‐film transistor (OTFT) fabricated mainly by inkjet printing and subsequently functionalized with antibodies for protein recognition. The BioFET is assessed for label‐free detection of a model protein, human immunoglobulin G (HIgG). It is characterized electrically to evaluate the contribution of each step in the functionalization of the OTFT and to detect the presence of the target protein. The fabrication, structure, materials optimization, electrical characteristics, and functionality of the starting OTFT and final BioFET are also discussed. Different materials are evaluated for the top insulator layer, with the aim of protecting the lower layers from the electrolyte and preserving the BioFET electrical performance.     

High‐Performance n‐Channel Thin‐Film Field‐Effect Transistors Based on a Nanowire‐Forming Polymer

A new electrontransport polymer, poly{[N,N′‐dioctylperylene‐3,4,9,10‐bis(dicarboximide)‐1,7(6)‐diyl]‐alt‐[(2,5‐bis(2‐ethyl‐hexyl)‐1,4‐phenylene)bis(ethyn‐2,1‐diyl]} (PDIC8‐EB), is synthesized. In chloroform, the polymer undergoes self‐assembly, forming a nanowire suspension. The nanowire's optical and electrochemical properties, morphological structure, and field‐effect transistor (FET) characteristics are investigated. Thin films fabricated from a PDIC8‐EB nanowire suspension are composed of ordered nanowires and ordered and amorphous non‐nanowire phases, whereas films prepared from a homogeneous PDIC8‐EB solution consist of only the ordered and amorphous non‐nanowire phases. X‐ray scattering experiments suggest that in both nanowires and ordered phases, the PDIC8 units are laterally stacked in an edge‐on manner with respect to the film plane, with full interdigitation of the octyl chains, and with the polymer backbones preferentially oriented within the film plane. The ordering and orientations are significantly enhanced through thermal annealing at 200 °C under inert conditions. The polymer film with high degree of structural ordering and strong orientation yields a high electron mobility (0.10 ± 0.05 cm² V^?1 s^?1), with a high on/off ratio (3.7 × 10⁶), a low threshold voltage (8 V), and negligible hysteresis (0.5 V). This study demonstrates that the polymer in the nanowire suspension provides a suitable material for fabricating the active layers of high‐performance n‐channel FET devices via a solution coating process.     

Kinetically Controlled Crystallization in Conjugated Polymer Films for High‐Performance Organic Field‐Effect Transistors

Ordering of semiconducting polymers in thin films from the nano to microscale is strongly correlated with charge transport properties as well as organic field‐effect transistor performance. This paper reports a method to control nano to microscale ordering of poly{[N,N′‐bis(2‐octyldodecyl)‐naphthalene‐1,4,5,8‐bis(dicarboximide)‐2,6‐diyl]‐alt‐5,5′‐(2,2′‐bithiophene)} (P(NDI2OD‐T2)) thin films by precisely regulating the solidification rate from the metastable state just before crystallization. The proposed simple but effective approach, kinetically controlled crystallization, achieves optimized P(NDI2OD‐T2) films with large polymer domains, long range ordered fibrillar structures, and molecular orientation preferable for electron transport leading to dramatic morphological changes in both polymer domain sizes at the micrometer scale and molecular packing structures at nanoscales. Structural changes significantly increase electron mobilities up to 3.43 ± 0.39 cm² V^?1 s^?1 with high reliability, almost two orders of enhancement compared with devices from naturally dried films. Small contact resistance is also obtained for electron injection (0.13 MΩ cm), low activation energy (62.51 meV), and narrow density of states distribution for electron transport in optimized thin films. It is believed that this study offers important insight into the crystallization of conjugated polymers that can be broadly applied to optimize the morphology of semiconducting polymer films for solution processed organic electronic devices.     

Sub‐3 V ZnO Electrolyte‐Gated Transistors and Circuits with Screen‐Printed and Photo‐Crosslinked Ion Gel Gate Dielectrics: New Routes to Improved Performance

A facile, high‐resolution patterning process is introduced for fabrication of electrolyte‐gated transistors (EGTs) and circuits using a photo‐crosslinkable ion gel and stencil‐based screen printing. The photo‐crosslinkable gel is based on a triblock copolymer incorporating UV‐sensitive terminal azide functionality and a common ionic liquid. Using this material in conjunction with conventional photolithography and stenciling techniques, well‐defined 0.5–1 μm thick ion gel films are patterned on semiconductor channels as narrow as 10 μm. The resulting n‐type ZnO EGTs display high electron mobility (>2 cm² Vs^?1) and on/off current ratios (>10⁵). Further, EGT‐based inverters exhibit static gains >23 at supply voltages below 3 V, and five‐stage EGT ring oscillator circuits display dynamic propagation delays of 50 μs per stage. In general, the screen printing and photo‐crosslinking strategy provides a clean room‐compatible method to fabricate EGT circuits with improved sensitivity (gain) and computational power (gain × oscillating frequency). Detailed device analysis indicates that significantly shorter delay times, of order 1 μs, can be obtained by improving the ion gel conductance.     

Donor–Acceptor‐Conjugated Polymer for High‐Performance Organic Field‐Effect Transistors: A Progress Report

Polymeric semiconductors have demonstrated great potential in the mass production of low‐cost, lightweight, flexible, and stretchable electronic devices, making them very attractive for commercial applications. Over the past three decades, remarkable progress has been made in donor–acceptor (D–A) polymer‐based field‐effect transistors, with their charge‐carrier mobility exceeding 10 cm² V^?1 s^?1. Numerous molecular designs of D–A polymers have emerged and evolved along with progress in understanding the charge transport physics behind their high mobility. In this review, the current understanding of charge transport in polymeric semiconductors is covered along with significant features observed in high‐mobility D–A polymers, with a particular focus on polymeric microstructures. Subsequently, emerging molecular designs with further prospective improvements in charge‐carrier mobility are described. Moreover, the current issues and outlook for future generations of polymeric semiconductors are discussed.     

A Noble Metal Dichalcogenide for High‐Performance Field‐Effect Transistors and Broadband Photodetectors

2D layered materials are an emerging class of low‐dimensional materials with unique physical and structural properties and extensive applications from novel nanoelectronics to multifunctional optoelectronics. However, the widely investigated 2D materials are strongly limited in high‐performance electronics and ultrabroadband photodetectors by their intrinsic weaknesses. Exploring the new and narrow bandgap 2D materials is very imminent and fundamental. A narrow‐bandgap noble metal dichalcogenide (PtS₂) is demonstrated in this study. The few‐layer PtS₂ field‐effect transistor exhibits excellent electronic mobility exceeding 62.5 cm² V^?1 s^?1 and ultrahigh on/off ratio over 10⁶ at room temperature. The temperature‐dependent conductance and mobility of few‐layer PtS₂ transistors show a direct metal‐to‐insulator transition and carrier scattering mechanisms, respectively. Remarkably, 2D PtS₂ photodetectors with broadband photodetection from visible to mid‐infrared and a fast photoresponse time of 175 µs at 830 nm illumination for the first time are obtained at room temperature. Our work opens an avenue for 2D noble‐metal dichalcogenides to be applied in high‐performance electronic and mid‐infrared optoelectronic devices.     

Temperature Performance of Doping‐Free Top‐Gate CNT Field‐Effect Transistors: Potential for Low‐ and High‐Temperature Electronics

High‐performance top‐gate carbon nanotube (CNT) field‐effect transistors (FETs) have been fabricated via a doping‐free fabrication process in which the polarity of the CNT FET is controlled by the injection of carriers from the electrodes, instead of using dopants. The performance of the doping‐free CNT FETs is systemically investigated over a wide temperature range, from very low temperatures of down to 4.3 K up to 573 K, and analyzed using several temperature‐dependent key device parameters including the ON/OFF state current and ratio, carrier mobility, and subthreshold swing. It is demonstrated that for ballistic and quasi‐ballistic CNT FETs, the operation of the CNT FETs is largely independent of the presence of dopant, thus avoiding detrimental effects due to dopant freeze‐out at low temperature and dopant diffusion at high temperature, and making it possible to use doping‐free CNT FETs in both low‐ and high‐temperature electronics. A new method is also proposed for extracting the band‐gap and diameter of a semiconducting CNT from the temperature dependent OFF‐state current and shown to yield results that are consistent with AFM measurements.     

Solution‐Processed Monolayer Organic Crystals for High‐Performance Field‐Effect Transistors and Ultrasensitive Gas Sensors

This work innovatively develops a dual solution‐shearing method utilizing the semiconductor concentration region close to the solubility limit, which successfully generates large‐area and high‐performance semiconductor monolayer crystals on the millimeter scale. The monolayer crystals with poly(methyl methacrylate) encapsulation show the highest mobility of 10.4 cm² V^?1 s^?1 among the mobility values in the reported solution‐processed semiconductor monolayers. With similar mobility to multilayer crystals, light is shed on the charge accumulation mechanism in organic field‐effect transistors (OFETs), where the first layer on interface bears the most carrier transport task, and the other above layers work as carrier suppliers and encapsulations to the first layer. The monolayer crystals show a very low dependency on channel directions with a small anisotropic ratio of 1.3. The positive mobility–temperature correlation reveals a thermally activated carrier transport mode in the monolayer crystals, which is different from the band‐like transport mode in multilayer crystals. Furthermore, because of the direct exposure of highly conductive channels, the monolayer crystal based OFETs can sense ammonia concentrations as low as 10 ppb. The decent sensitivity indicates the monolayer crystals are potential candidates for sensor applications.     

Hydrocarbons‐Driven Crystallization of Polymer Semiconductors for Low‐Temperature Fabrication of High‐Performance Organic Field‐Effect Transistors

While many high‐performance polymer semiconductors are reported for organic field‐effect transistors (OFETs), most require a high‐temperature postdeposition annealing of channel semiconductors to achieve high performance. This negates the fundamental attribute of OFETs being a low‐cost alternative to conventional high‐cost silicon technologies. A facile solution process is developed through which high‐performance OFETs can be fabricated without thermal annealing. The process involves incorporation of an incompatible hydrocarbon binder or wax into the channel semiconductor composition to drive rapid phase separation and instantaneous crystallization of polymer semiconductor at room temperature. The resulting composite channel semiconductor film manifests a nano/microporous surface morphology with a continuous semiconductor nanowire network. OFET mobility of up to about 5 cm² V^?1 s^?1 and on/off ratio ≥ 10⁶ are attained. These are hitherto benchmark performance characteristics for room‐temperature, solution‐processed polymer OFETs, which are functionally useful for many impactful applications.     

High‐Density Carrier Accumulation in ZnO Field‐Effect Transistors Gated by Electric Double Layers of Ionic Liquids

Very recently, electric‐field‐induced superconductivity in an insulator was realized by tuning charge carrier to a high density level (1 × 10¹⁴ cm^?2). To increase the maximum attainable carrier density for electrostatic tuning of electronic states in semiconductor field‐effect transistors is a hot issue but a big challenge. Here, ultrahigh density carrier accumulation is reported, in particular at low temperature, in a ZnO field‐effect transistor gated by electric double layers of ionic liquid (IL). This transistor, called an electric double layer transistor (EDLT), is found to exhibit very high transconductance and an ultrahigh carrier density in a fast, reversible, and reproducible manner. The room temperature capacitance of EDLTs is found to be as large as 34 µF cm^?2, deduced from Hall‐effect measurements, and is mainly responsible for the carrier density modulation in a very wide range. Importantly, the IL dielectric, with a supercooling property, is found to have charge‐accumulation capability even at low temperatures, reaching an ultrahigh carrier density of 8×10¹⁴ cm^?2 at 220 K and maintaining a density of 5.5×10¹⁴ cm^?2 at 1.8 K. This high carrier density of EDLTs is of great importance not only in practical device applications but also in fundamental research; for example, in the search for novel electronic phenomena, such as superconductivity, in oxide systems.     

Insulator Polarization Mechanisms in Polyelectrolyte‐Gated Organic Field‐Effect Transistors

Electrolyte‐gated organic field‐effect transistors (OFETs) hold promise for robust printed electronics operating at low voltages. The polarization mechanism of thin solid electrolyte films, the gate insulator in such OFETs, is still unclear and appears to limit the transient current characteristics of the transistors. Here, the polarization response of a thin proton membrane, a poly(styrenesulfonic acid) film, is controlled by varying the relative humidity. The formation of the conducting transistor channel follows the polarization of the polyelectrolyte, such that the drain transient current characteristics versus the time are rationalized by three different polarization mechanisms: the dipolar relaxation at high frequencies, the ionic relaxation (migration) at intermediate frequencies, and the electric double‐layer formation at the polyelectrolyte interfaces at low frequencies. The electric double layers of polyelectrolyte capacitors are formed in ～1 µs at humid conditions and an effective capacitance per area of 10 µF cm^?2 is obtained at 1 MHz, thus suggesting that this class of OFETs might operate at up to 1 MHz at 1 V.     

High‐Performance,Air‐Stable,Top‐Gate,p‐Channel WSe2 Field‐Effect Transistor with Fluoropolymer Buffer Layer

High‐performance, air‐stable, p‐channel WSe₂ top‐gate field‐effect transistors (FETs) using a bilayer gate dielectric composed of high‐ and low‐k dielectrics are reported. Using only a high‐k Al₂O₃ as the top‐gate dielectric generally degrades the electrical properties of p‐channel WSe₂, therefore, a thin fluoropolymer (Cytop) as a buffer layer to protect the 2D channel from high‐k oxide forming is deposited. As a result, a top‐gate‐patterned 2D WSe₂ FET is realized. The top‐gate p‐channel WSe₂ FET demonstrates a high hole mobility of 100 cm²_­ V^?1 s^?1 and a I_ON/I_OFF ratio > 10⁷ at low gate voltages (V_GS ca. ?4 V) and a drain voltage (V_DS) of ?1 V on a glass substrate. Furthermore, the top‐gate FET shows a very good stability in ambient air with a relative humidity of 45% for 7 days after device fabrication. Our approach of creating a high‐k oxide/low‐k organic bilayer dielectric is advantageous over single‐layer high‐k dielectrics for top‐gate p‐channel WSe₂ FETs, which will lead the way toward future electronic nanodevices and their integration.     

Systematic Study of Widely Applicable N‐Doping Strategy for High‐Performance Solution‐Processed Field‐Effect Transistors

A specific design for solution‐processed doping of active semiconducting materials would be a powerful strategy in order to improve device performance in flexible and/or printed electronics. Tetrabutylammonium fluoride and tetrabutylammonium hydroxide contain Lewis base anions, F^? and OH^?, respectively, which are considered as organic dopants for efficient and cost‐effective n‐doping processes both in n‐type organic and nanocarbon‐based semiconductors, such as poly[[N,N′‐bis(2‐octyldodecyl)‐naphthalene‐1,4,5,8‐bis(dicarboximide)‐2,6‐diyl]‐alt‐5,5′‐(2,2′‐bithiophene)] (P(NDI2OD‐T2)) and selectively dispersed semiconducting single‐walled carbon nanotubes by π‐conjugated polymers. The dramatic enhancement of electron transport properties in field‐effect transistors is confirmed by the effective electron transfer from the dopants to the semiconductors as well as controllable onset and threshold voltages, convertible charge‐transport polarity, and simultaneously showing excellent device stabilities under ambient air and bias stress conditions. This simple solution‐processed chemical doping approach could facilitate the understanding of both intrinsic and extrinsic charge transport characteristics in organic semiconductors and nanocarbon‐based materials, and is thus widely applicable for developing high‐performance organic and printed electronics and optoelectronics devices.     

Low‐k Insulators as the Choice of Dielectrics in Organic Field‐Effect Transistors

In this paper, we present a new effect influencing the operation of organic field‐effect transistors resulting from the choice of gate insulator material. In a series of studies it was found that the interaction between the insulator and the semiconductor materials plays an important role in carrier transport. The insulator is not only capable of affecting the morphology of the semiconductor layer, but can also change the density of states by local polarization effects. Carrier localization is enhanced by insulators with large permittivities, due to the random dipole field present at the interface. We have investigated this effect on a number of disordered organic semiconductor materials, and show here that significant benefits are achievable by the use of low‐k dielectrics as opposed to the existing trend of increasing the permittivity for low operational voltage. We also discuss fundamental differences in the case of field‐effect transistors with band‐like semiconductors.