Isothermal crystallization and melting behavior of polypropylene with lanthanum complex of cyclodextrin derivative as a β‐nucleating agent

A novel highly active β‐nucleating agent, β‐cyclodextrin complex with lanthanum (β‐CD‐MAH‐La), was introduced to isotactic polypropylene (iPP). Its influence on isothermal crystallization and melting behavior of iPP was investigated by differential scanning calorimeter (DSC), wide‐angle X‐ray diffraction (WAXD), and polarized light microscopy (PLM). WAXD results demonstrated that β‐CD‐MAH‐La was an effective β‐nucleating agent, with β‐crystal content of iPP being strongly influenced by the content of β‐CD‐MAH‐La and the isothermal crystallization temperature. The isothermal crystallization kinetics of pure iPP and iPP/β‐CD‐MAH‐La was described appropriately by Avrami equation, and results revealed that β‐CD‐MAH‐La promoted heterogeneous nucleation and accelerated the crystallization of iPP. In addition, the equilibrium melting temperature (T) of samples was determined using linear and nonlinear Hoffman‐Weeks procedure. Finally, the Lauritzen‐Hoffman secondary nucleation theory was applied to calculate the nucleation parameter (K_g) and the fold surface energy (σ_e), the value of which verify that the addition of β‐CD‐MAH‐La reduced the creation of new surface for β‐crystal and then led to faster crystallization rate. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis,physical properties,and crystallization of optically active poly(L‐phenyllactic acid) and poly(L‐phenyllactic acid‐co‐L‐lactic acid)

Optically active poly(L ‐phenyllactic acid) (Ph‐PLLA), poly(L ‐lactic acid) (PLLA), and poly(L ‐phenyllactic acid‐co‐L ‐lactic acid) with weight‐average molecular weight exceeding 6 × 10³ g mol^?1 were successfully synthesized by acid catalyzed direct polycondensation of L ‐phenyllactic acid and/or L ‐lactic acid in the presence of 2.5–10 wt % of p‐toluenesulfonic acid. Their physical properties and crystallization behavior were investigated by differential scanning calorimetry, thermogravimetry, and polarimetry. The absolute value of specific optical rotation ([α]) for Ph‐PLLA (?38 deg dm^?1 g^?1 cm³) was much lower than that of [α] for PLLA (?150 deg dm^?1 g^?1 cm³), suggesting that the helical nature was reduced by incorporation of bulky phenyl group. PLLA was crystallizable during solvent evaporation, heating from room temperature, and cooling from the melt. Incorporation of a very low content of bulky phenyllactyl units even at 4 mol % suppressed the crystallization of L ‐lactyl unit sequences during heating and cooling, though the copolymers were crystallizable for L ‐phenylactyl units up to 6 mol % during solvent evaporation. The activation energy of thermal degradation (ΔE_td) for Ph‐PLLA (200 kJ mol^?1) was higher than that for PLLA (158 kJ mol^?1). The ΔE_td for the copolymers increased with an increase in L ‐phenyllactyl unit content. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Photocatalytic degradation of 2,2‐bis(4‐hydroxy‐3‐methylphenyl) propane (BPP) based on molecular recognition interaction

BACKGROUND: Endocrine disruptors in the aquatic environment and their potential adverse effects are currently issues of concern. One of these endocrine disruptors is 2,2‐bis(4‐hydroxy‐3‐methylphenyl)propane (BPP). In this work the molecular recognition interaction of BPP with β‐cyclodextrin (β‐CD) was studied using IR spectroscopy and steady state fluorescence spectroscopy, and the photocatalytic degradation behaviour of BPP based on molecular recognition interaction was investigated in a TiO₂/UV–visible (λ_max = 365 nm) system. This might provide a new method for the treatment of some organic pollutants in wastewater. RESULTS: β‐CD reacts with BPP to form a 1:1 inclusion complex, the formation constant of which is 4.94 × 10³ L mol^?1. The photodegradation rate constant of BPP after molecular recognition by β‐CD showed a 1.42‐fold increase in the TiO₂/UV–visible (λ_max = 365 nm) system. The photodegradation of BPP depended on the concentration of β‐CD, the pH value, the gaseous medium and the initial concentration of BPP. The photodegradation efficiency of BPP with molecular recognition was higher than that without molecular recognition. After 100 min of irradiation the mineralisation efficiency of BPP after molecular recognition by β‐CD reached 94.8%, whereas the mineralisation efficiency of BPP before molecular recognition by β‐CD was only 40.6%. CONCLUSION: The photocatalytic degradation of BPP after molecular recognition by β‐CD can be enhanced in the TiO₂/UV‐visible (λ_max = 365 nm) system. This enhancement is dependent on the enhancement of the adsorption of BPP, the moderate inclusion depth of BPP in the β‐CD cavity and the increase in the frontier electron density of BPP after molecular recognition. Copyright © 2008 Society of Chemical Industry     

Atom‐transfer radical polymerization of methyl methacrylate with α,α′‐dichloroxylene/CuCl/N,N,N′,N″,N″‐pentamethyldiethylenetriamine initiation system under microwave irradiation

The atom‐transfer radical polymerization (ATRP) of methyl methacrylate (MMA), using α,α′‐dichloroxylene as initiator and CuCl/N,N,N′,N″,N″‐pentamethyldiethylenetriamine as catalyst was successfully carried out under microwave irradiation (MI). The polymerization of MMA under MI showed linear first‐order rate plots, a linear increase of the number‐average molecular weight with conversion, and low polydispersities, which indicated that the ATRP of MMA was controlled. Using the same experimental conditions, the apparent rate constant (k) under MI (k = 7.6 × 10^?4 s^?1) was higher than that under conventional heating (k = 5.3 × 10^?5 s^?1). © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2189–2195, 2004     

Carboxyl terminated polyamide 12 chain extension by reactive extrusion using a dioxazoline coupling agent. Part I: Extrusion parameters analysis

Condensation reaction between a carboxyl terminated polyamide 12 (CTPA) (Mn = 2000 g mol^?1) and a dioxazoline [2,2′‐(1,3‐phenylene)‐bis(2‐oxazoline)] (OO) was achieved by reactive extrusion. Extrusion parameters effects on the process were analyzed through residence time distribution (RTD) and conversion distribution (CD) evolutions. RTD was measured using ultraviolet and ultrasonic detectable tracers. RTD measured along the extruder screws showed a decrease of the dimensionless variance (σ) with the reaction progress. Comparing measured molar masses and dispersity with those calculated using CD, competition between condensation and chain scission was detected. Effects of barrel temperature, screw profile, rotation speed and viscous dissipation on the reactive system evolution were analyzed and used for the process optimization. It was shown that a polyester amide with a Dp _n 12 can be obtained using this dioxazoline coupling agent by reactive extrusion.     

Viscometric Study of the Inclusion Complex Between β‐Cyclodextrin and HTAC in Aqueous Solution

The inclusion complex formed by β‐cyclodextrin (β‐CD) with the cationic surfactant hexadecyltrimethylammonium chloride (HTAC) was studied by viscometry using poly(ethylene oxide) (PEO)–HTAC aggregates as a viscosity indicator. The relative viscosity of β‐CD in aqueous PEO–HTAC solution profiles shows that the formation of the β‐CD/HTAC inclusion complex causes HTAC molecules to be stripped off the PEO chains, resulting in a decrease of aqueous solution viscosity as a result of the decrease in electrostatic repulsion between polymer‐bound HTAC micelles. The viscosity minimum at C_β‐CD/C_HTAC = 0.5 indicates that the molecular ratio of host molecule to guest molecule is 1:2 in the β‐CD/HTAC inclusion complex.     

Synthesis and characterization of grafting β‐cyclodextrin with chitosan

Two new adsorbents [β‐cyclodextrin–chitosan (β‐CD–CTS) and β‐cyclodextrin‐6–chitosan (β‐CD‐6‐CTS)] were synthesized by the reaction of β‐cyclodextrin (β‐CD) with epoxy‐activated chitosan (CTS) and the sulfonation of the C‐6 hydroxyl group of β‐cyclodextrin with CTS, respectively. Their structures were confirmed by IR spectral analysis and X‐ray diffraction analysis, and their apparent amount of grafting was determined by ultraviolet spectroscopy. The adsorption properties of β‐CD‐CTS and β‐CD‐6‐CTS for p‐dihydroxybenzene were studied. The experimental results showed that the two new adsorbents exerted adsorption on the carefully chosen target. The highest saturated capacity of p‐dihydroxybenzene of β‐CD‐CTS and β‐CD‐6‐CTS were 51.68 and 46.41 mg/g, respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 860–864, 2004     

Nonisothermal crystallization and melting behavior of β‐nucleated isotactic polypropylene and polyamide 66 blends

A highly novel nano‐CaCO₃ supported β‐nucleating agent was employed to prepare β‐nucleated isotactic polypropylene (iPP) blend with polyamide (PA) 66, β‐nucleated iPP/PA66 blend, as well as its compatibilized version with maleic anhydride grafted PP (PP‐g‐MA), maleic anhydride grafted polyethylene‐octene (POE‐g‐MA), and polyethylene‐vinyl acetate (EVA‐g‐MA), respectively. Nonisothermal crystallization behavior and melting characteristics of β‐nucleated iPP and its blends were investigated by differential scanning calorimeter and wide angle X‐ray diffraction. Experimental results indicated that the crystallization temperature (T) of PP shifts to high temperature in the non‐nucleated PP/PA66 blends because of the α‐nucleating effect of PA66. T of PP and the β‐crystal content (K_β) in β‐nucleated iPP/PA66 blends not only depended on the PA66 content, but also on the compatibilizer type. Addition of PP‐g‐MA and POE‐g‐MA into β‐nucleated iPP/PA66 blends increased the β‐crystal content; however, EVA‐g‐MA is not benefit for the formation of β‐crystal in the compatibilized β‐nucleated iPP/PA66 blend. It can be relative to the different interfacial interactions between PP and compatibilizers. The nonisothermal crystallization kinetics of PP in the blends was evaluated by Mo's method. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Adsorption and drug release based on β‐cyclodextrin‐grafted hydroxyapatite composite

In this study, β‐cyclodextrin (β‐CD) was covalently grafted on hydroxyapatite (HA) using a coupling agent to improve the drug loading capacity and prolong the drug release. The binding of β‐CD on the HA surface was confirmed by Fourier transformation infrared spectroscopy, thermal gravimetric analysis, and X‐ray powder diffraction. The adsorption capacity of ofloxacin on β‐CD‐grafted hydroxyapatite (β‐CD‐g‐HA) composite was found to be 30 mg g^?1 at 37°C and 24 h. The adsorption process is spontaneous, given the negative values of free energy change. Compared with the release of ofloxacin loaded on HA, the release of ofloxacin loaded on β‐CD‐g‐HA was slowed down 28% and 21% in pH 2.0 and pH 7.4 buffer media at 2 h, respectively. Biocompatibility of β‐CD‐g‐HA was assessed by MTT assay, and the result showed that it had no cytotoxicity. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Kinetic and thermodynamic investigation of Arthrospira (Spirulina) platensis fed‐batch cultivation in a tubular photobioreactor using urea as nitrogen source

BACKGROUND: Fed‐batch culture allows the cultivation of Arthrospira platensis using urea as nitrogen source. Tubular photobioreactors substantially increase cell growth, but the successful use of this cheap nitrogen source requires a knowledge of the kinetic and thermodynamic parameters of the process. This work aims at identifying the effect of two independent variables, temperature (T) and urea daily molar flow‐rate (U), on cell growth, biomass composition and thermodynamic parameters involved in this photosynthetic cultivation. RESULTS: The optimal values obtained were T = 32 °C and U = 1.16 mmol L^?1 d^?1, under which the maximum cell concentration was 4186 ± 39 mg L^?1, cell productivity 541 ± 5 mg L^?1 d^?1 and yield of biomass on nitrogen 14.3 ± 0.1 mg mg^?1. Applying an Arrhenius‐type approach, the thermodynamic parameters of growth (ΔH* = 98.2 kJ mol^?1; ΔS* = ? 0.020 kJ mol^?1 K^?1; ΔG* = 104.1 kJ mol^?1) and its thermal inactivation ( kJ mol^?1; kJ mol^?1 K^?1; kJ mol^?1) were estimated. CONCLUSIONS: To maximize cell growth T and U were simultaneously optimized. Biomass lipid content was not influenced by the experimental conditions, while protein content was dependent on both independent variables. Using urea as nitrogen source prevented the inhibitory effect already observed with ammonium salts. Copyright © 2012 Society of Chemical Industry     

Adsorption of a gold‐iodide complex (AuI2−) onto cellulose acetate‐polyaniline membranes: Equilibrium experiments

The adsorption of AuI complex onto acetate cellulose‐polyaniline membranes was investigated. Kinetic experiments showed a rapid adsorption of this complex, which was attributed to an ion‐exchange mechanism. Equilibrium adsorption results were represented by the Langmuir model, showing a correlation coefficient of 0.9852. Langmuir parameters K and Q_m were found to be 0.2937 L mg^?1 and 1.2394 mg g^?1, respectively. Approximately 94% of AuI was adsorbed when a solid/liquid ratio of 40 g L^?1 (grams of membrane/ liter of solution) was used. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

The transformation: Brushite → calcium monofluorophosphate under aqueous conditions

The reaction between CaHPO₄. 2H₂O and 10^?1 M solution of Na₂PO₃F have been studied in the pH range 7 to 5 at 25 °C. The formation of CaPO₃F · 2H₂O, rather than CaF₂ or Ca₅F (PO₄)₃ by initial hydrolysis and subsequent reaction with the F^? formed, appeared to occur. The value of ΔG for CaPO₃F · 2H₂O has been calculated as – 530.9 kcal mol^?1. A comparison is drawn to the exchange reactions reported here, and to the similar reactions reported to occur in calcium deficient apatite.     

Heavy Metal Removal and Neutralization of Acid Mine Waste Water ‐ Kinetic Study

The influence of the apatite on the efficiency of neutralization and on heavy metal removal of acid mine waste water has been studied. The analysis of the treated waste water samples with apatite has shown an advanced purification, the concentration of the heavy metals after the treatment of the waste water with apatite being 25 to 1000 times less than the Maximum Concentration Limits admitted by European Norms (NTPA 001/2005). In order to establish the macro‐kinetic mechanism in the neutralization process, the activation energy, Ea, and the kinetic parameters, rate coefficient of reaction, k_r, and k_t were determined from the experimental results obtained in “ceramic ball‐mill” reactor. The obtained values of the activation energy Ea >> 42 kJ mol^?1 (e.g. Ea = 115.50 ± 7.50 kJ mol^?1 for a conversion of sulphuric acid η_H2SO4 = 0.05, Ea = 60.90 ± 9.50 kJ mol^?1 for η ^H2SO4 = 0.10 and Ea = 55.75 ± 10.45 kJ mol^‐1 for η ^H2SO4 = 0.15) suggest that up to a conversion of H2SO4 equal 0.15 the global process is controlled by the transformation process, adsorption followed by reaction, which means surface‐controlled reactions. At a conversion of sulphuric acid η ^H2SO4 > 0.15, the obtained values of activation energy Ea < 42 kJ mol^‐1 (e.g. Ea = 37.55 ± 4.05 kJ mol^‐1 for η ^H2SO4 = 0.2, Ea = 37.54 ± 2.54 kJ mol^‐1 for η ^H2SO4 = 0.3 and Ea = 37.44 ± 2.90 kJ mol^‐1 for η ^H2SO4 = 0.4) indicate diffusion‐controlled processes. This means a combined process model, which involves the transfer in the liquid phase followed by the chemical reaction at the surface of the solid. Kinetic parameters as rate coefficient of reaction, kr with values ranging from (5.02 ± 1.62) 10‐4 to (8.00 ± 1.55) 10‐4 (s^‐1) and transfer coefficient, kt, ranging from (8.40 ± 0.50) 10‐5 to (10.42 ± 0.65) 10‐5 (m s^‐1) were determined.     

Radical polymerization of n‐butyl methacrylate initiated by stibonium ylide

1,2,3,4‐Tetraphenylcyclopentadiene triphenyl stibonium ylide initiated radical polymerization of n‐butyl methacrylate (n‐BMA) in dioxane at (60 ± 0.2)°C for 90 min under nitrogen atmosphere has been carried out. The system follows nonideal kinetics, i.e., R_p α [ylide]^0.2 [n‐BMA]^1.8. The value of k/k_t and overall energy of activation have been computed as 0.133 × 10^?2 L mol^?1 s^?1, 33 kJ/mol, respectively. The FTIR spectrum shows a band at 1745 cm^?1 due to acrylate group of n‐BMA. The ¹H NMR spectrum shows a peak of two magnetically equivalent protons of methylene group at 2.1 δ ppm. The DSC curve shows glass transition temperature (T_g) as 41°C. The presence of six hyperfine lines in ESR spectrum indicates that the system follows free radical polymerization and the initiation is brought about by phenyl radical. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2457–2463, 2007     

Synthesis,characterization, and thermodynamic properties of poly(3‐mesityl‐2‐hydroxypropyl methacrylate)

Poly(3‐mesityl‐2‐hydroxypropyl methacrylate) (PMHPMA) was synthesized in a 1,4‐dioxane solution with 2,2′‐azobisisobutyronitrile as the initiator at 60°C. The homopolymer and its monomer were characterized with ¹H‐ and ¹³C‐NMR, Fourier transform infrared, differential scanning calorimetry, thermogravimetric analysis, size exclusion chromatography, and elemental analysis techniques. According to size exclusion chromatography analysis, the number‐average molecular weight, weight‐average molecular weight, and polydispersity index of PMHPMA were 65,864 g/mol, 215,375 g/mol, and 3.275, respectively. According to thermogravimetric analysis, the carbonaceous residue value of PMHPMA was 14% at 500°C. The values of the specific retention volume, adsorption enthalpy, sorption enthalpy, sorption free energy, sorption entropy, partial molar free energy, partial molar heat of mixing, weight fraction activity coefficient of solute probes at infinite dilution (Ω), and Flory–Huggins interaction parameter (χ) were calculated for the interactions of PMHPMA with selected alcohols and alkanes by the inverse gas chromatography method at various temperatures. According to Ω and χ, selected alcohols and alkanes were nonsolvents for PMHPMA at 423–453 K. Also, the solubility parameter of PMHPMA (δ₂) was found to be 24.24 and 26.33 (J/cm³)^0.5 from the slope and intercept of (δ/RT) ? χ/V₁ = (2δ₂/RT)δ₁ ? δ/RT at 443 K, respectively [where δ₁ is the solubility parameter of the probe, V₁ is the molar volume of the solute, T is the column temperature (K), and R is the universal gas constant]. The glass‐transition temperature of PMHPMA was found to be 386 and 385 K by inverse gas chromatography and differential scanning calorimetry techniques, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 101–109, 2006     

RAFT polymerization of N‐vinyl pyrrolidone using prop‐2‐ynyl morpholine‐4‐carbodithioate as a new chain transfer agent

RAFT polymerization of N‐vinyl pyrrolidone (NVP) has been investigated in the presence of chain transfer agent (CTA), i.e., prop‐2‐ynyl morpholine‐4‐carbodithioate (PMDC). The influence of reaction parameters such as monomer concentration [NVP], molar ratio of [CTA]/[AIBN, i.e., 2,2′‐azobis (2‐methylpropionitrile)] and [NVP]/[CTA], and temperature have been studied with regard to time and conversion limit. This study evidences the parameters leading to an excellent control of molecular weight and molar mass dispersity. NVP has been polymerized by maintaining molar ratio [NVP]: [PMDC]: [AIBN] = 100 : 1 : 0.2. Kinetics of the reaction was strongly influenced by both temperature and [CTA]/[AIBN] ratio and to a lesser extent by monomer concentration. The activation energy (E_a = 31.02 kJ mol^?1) and enthalpy of activation (ΔH^?= 28.29 kJ mol^?1) was in a good agreement to each other. The negative entropy of activation (ΔS^? = ?210.16 J mol^‐1K^‐1) shows that the movement of reactants are highly restricted at transition state during polymerization. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Melting behavior of poly(trimethylene terephthalate)

In this study, the melting behavior of isothermally crystallized polytri‐ methylene terephthalate (PTT) was investigated. Multiple melting behaviors in DSC heating trace were found because two populations of lamellar stacks were formed during primary crystallization and the recrystallization at heating process, respectively. This fact could be also confirmed from the result of optical microscopy observation. The Hoffman–Weeks equation was applied to obtain equilibrium melting temperature (T). The T value of PTT is about 525 K, which is 10 K higher than that reported. Combining the enthalpy of fusion from the DSC result and the degree of crystallinity from WAXD result, the value of the equilibrium‐melting enthalpy ΔH was deduced to be approximately 28.8 kJ mol^?1. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2426–2433, 2002     

Radical terpolymerization of zincacrylate,acrylonitrile, and styrene initiated by As2S3-styrene complex

Terpolymerization was investigated by dilatometry for zincacrylate (ZnA₂), acrylonitrile (AN), and styrene (St), radically initiated by a As₂S₃-styrene complex (I) in dimethyl sulphoxide (DMSO), at 90 ± 0.1°C for 1 h under inert atmosphere. The system follows non-ideal kinetics, due to primary radical termination as well as a degradative chain transfer reaction. The kinetic expression for the system is R_pα(I)^0.27 (St)^0.31 (AN) ^0.22[ZnA₂]^0.12. The value for the activation energy and k/k_t are 55 kJ mol^?1 and 1.87 × 10^?7 1 mol^?1 s^?1 respectively. The terpolymer has been characterized by IR and NMR spectroscopy. The thermal stability and solubility of the terpolymer have also been studied.     

Preparation and characterization of a novel responsive hydrogel with a β‐cyclodextrin‐based macromonomer

Based on a combination of poly(N‐isopropylacrylamide), which could respond to an external temperature, and β‐cyclodextrin (β‐CD), which could form a molecular inclusion complex, a novel hydrogel, having both thermal and pH sensitivities and containing β‐CD and N‐isopropylacrylamide (NIPA) segments, was synthesized. For the incorporation of β‐CD into the polymer network, a macromonomer was prepared first by the reaction of a β‐CD‐based polymer with maleic anhydride in dimethylformamide and then by copolymerization with NIPA in an aqueous solution. Elemental analysis, IR spectroscopy, differential scanning calorimetry, and swelling measurements were employed for the characterization of the hydrogel chain structure and its physical properties. With methyl orange as a model compound in inclusion tests, it was found that the hydrogel not only possessed a remarkable supramolecular inclusion ability (with respect to that of the small molecule cyclodextrin) but also could sensitively respond to various external stimuli, including the temperature, pH, and ionic strength. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 361–367, 2003     

Fundamental studies on a new series of SPSEBS‐PVA‐QPSEBS bipolar membrane: Membrane preparation and characterization

A sulfonated polystyrene ethylene butylene polystyrene (SPSEBS)‐poly(vinyl alcohol) (PVA)‐Quaternized polystyrene ethylene butylene polystyrene (QPSEBS) bipolar membrane (BPM) was prepared by lamination method using PSEBS as the starting material, the functionalization of which was modified by sulfonation and amination while PVA was used as the intermediate layer to enhance the water splitting efficiency. The cross section view of SPSEBS‐PVA‐QPSEBS BPM was studied by SEM. Fourier transform infra‐red spectroscopy (FTIR) studies indicated that the prepared BPM contained –SO, –NR, and –C‐N functional groups. The thermal stability of the prepared BPM was studied by thermogravimetric analysis (TGA). Some of the BPM characteristics results showed that the co‐ion fluxes was greater for t(0.065) when compared with t(0.051) along with a water splitting capacity value of 0.88 for SPSEBS‐PVA‐QPSEBS BPM. The water dissociation flux was 2.8 × 10^?5 mol/m²/s and 2.2 × 10^?5 mol/m²/s for the acid (H⁺) and base (OH^?), respectively. The other essential current‐voltage characteristics and permeate flux across the membrane were also evaluated. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci 2013