Insulin oxidation and determination at carbon electrodes

The redox chemistry of insulin was investigated at glassy carbon (GC) electrodes that were coated with films of chitosan (CHIT) and multiwalled carbon nanotubes (CNT). While bare electrodes deactivated quickly during insulin oxidation, the GC electrodes coated with CHIT and CHIT-CNT films generated stable insulin currents. The GC/CHIT-CNT electrodes were used for investigating the electrooxidation process of insulin and amperometric determination of insulin. The mass spectrometric, electron paramagnetic resonance, and separation studies of electrolyzed insulin solutions suggested that the loss of 4 mass units upon insulin oxidation at CNT could be accounted for by the formation of two dityrosine cross-links intramolecularly. At a potential of 0.700 V and physiological pH 7.40, the GC/CHIT-CNT electrodes displayed a detection limit of approximately 30 nM insulin (S/N = 3), sensitivity of 135 mA M(-1) cm(-2), linear dynamic range from 0.10 to 3.0 microM (R2 = 0.995), and superior operational and long-term stability. The CNT-based electrodes are promising new insulin detectors for diabetes-related studies such as fast chromatographic analysis of therapeutic insulin formulations or evaluation of quality of pancreatic islets prior to their transplantation.     

Electrochemical oxidation of oxalic acid at highly boron-doped diamond electrodes

Electrochemical oxidation of oxalic acid has been investigated at bare, highly boron-doped diamond electrodes. Cyclic voltammetry and flow injection analysis with amperometric detection were used to study the electrochemical reaction. Hydrogen-terminated diamonds exhibited well-defined peaks of oxalic acid oxidation in a wide pH range. A good linear response was observed for a concentration range from 50 nM to 10 microM, with an estimated detection limit of approximately 0.5 nM (S/N = 3). In contrast, oxygen-terminated diamonds showed no response for oxalic acid oxidation inside the potential window, indicating that surface termination contributed highly to the control of the oxidation reaction. An investigation with glassy carbon electrodes was conducted to confirm the surface termination effect on oxalic acid oxidation. Although a hydrogen-terminated glassy carbon electrode showed an enhancement of signal-to-background ratio in comparison with untreated glassy carbon, less stability of the current responses was observed than that at hydrogen-terminated diamond.     

Computer simulation of charge-selective electrochemistry of catechols at high-surface-area carbon fibers

The shape and size of cyclic voltammetric (CV) waves at the ultrahigh surface area carbon fiber are dependent on the pH and the charge of the electroactive species. The high surface area resulted from the fiber being fractured by application of a high anodic potential or current. The CV waves have been computer simulated with a model that assumes the entry of positively charged and, in some cases, neutral ones, but rejection of negatively charged species from the interior of the fractured fibers. Best fit between the computer-calculated and experimental CV waves is obtained for a model containing three components as the source of the current: (a) background capacitive charge, (b) diffusion to the outer cylindrical-shaped fiber, and (c) interior thin-layer volume. Simulation results indicate that the values for the inner void volume are in the nanoliter range when electroactive species penetrate the interior.     

碳纳米管/铁氰化镍/聚苯胺杂化膜对抗坏血酸的电催化氧化

采用循环伏安一步共聚法在碳纳米管修饰的铂基体上制备了立方体的铁氰化镍/聚苯胺/碳纳米管杂化膜;采用循环伏安法和计时电流法测试了杂化膜对抗坏血酸的电催化氧化性能;通过扫描电子显微镜(SEM)观察了杂化膜电极的表观形貌。结果表明,该电极对抗坏血酸具有较高的电催化氧化活性;在0.1 mol/L PBS和0.1 mol/L KNO3的溶液中,该杂化膜电极对抗坏血酸的催化氧化电流与其浓度在1×10-5～1.4×10-4mol/L呈良好的线性关系,相关性系数R=0.996 6,检出限为6.09×10-6mol/L,同时具有较高的灵敏度754.8 mA.M-1.cm-2,并采用计时电流法对抗坏血酸催化氧化的扩散系数和催化速率常数进行了研究。     

多孔的修饰电极对抗坏血酸的电催化氧化

通过循环伏安(CV)法制备了聚苯胺/聚砜(PAN/PSF)复合膜修饰电极,考察了电极对抗坏血酸(AA)的电催化性能。结果显示,PAN/PSF复合膜修饰电极对AA有很好的电催化氧化作用和高的稳定性。氧化峰电流与AA浓度在一定浓度范围内呈良好的线性关系,检测限为6×10-6 mol/L。该电极制备简单、灵敏度高、检测限低,对水果中AA具有很好的检测效果。     

Screen printing of nucleic acid detecting carbon electrodes

A large fraction of the presently mass-manufactured (> 10(8) units/year) electrochemical biosensors, used mostly by diabetic people to monitor their blood glucose levels, have screen-printed carbon working electrodes. An earlier study (Campbell, C. N., et al. Anal. Chem. 2002, 74, 158-162) showed that nucleic acids can be assayed at 1 nM concentrations by a sandwich-type amperometric method. The assay was performed with vitreous carbon working electrodes on which an electron-conducting polycationic redox polymer and avidin were coelectrodeposited. Because the rate of the electrodeposition increases with the surface density of the polycationic redox polymer, its practicality depends on pretreatment of the surface, which adds anionic functions. (Gao, Z., et al. Angew. Chem. Int. Ed. 2002, 41, 810-813). Here it is shown that the required conducting redox polymer films can be electrodeposited on potentially mass manufacturable electrodes made by screen-printing hydrophilic carbon inks on polyester sheets. The modified electrodes are made in two steps. First a polycationic electron-conducting redox polymer is cross-linked and electrodeposited by applying a negative potential. Next, an amine-terminated 20-base single-stranded oligonucleotide is electrodeposited by ligand-exchange. Both steps involve exchange of a labile inner sphere chloride ligand of the polymer-bound osmium-complex: Cross-linking and electrodeposition of the redox polymer result when inner-sphere chloride anions of the osmium complexes are exchanged by imidazole functions of neighboring chains. Incorporation of the oligonucleotide in the redox polymer results in the formation of a coordinative bond between the terminal amine (attached through a spacer to the oligonucleotide) and the osmium complex. In testing for the presence of a 38-base oligonucleotide, the analyte, in a 15- or 25-microL droplet of hybridization solution, is hybridized with and captured by the 20-base electrode-bound sequence; then it is hybridized with an 18-base horseradish peroxidase labeled sequence. When the HRP label electrically contacts the redox polymer, the film becomes an electrocatalyst for the reduction of H2O2 to water at 0.10 V (Ag/AgCl). Flow of the H2O2-reduction current indicates the presence of the assayed sequence.     

Anodic surface oxidation mechanisms of PAN-based and pitch-based carbon fibres

In order to clarify the differences in the anodic surface oxidation mechanisms of PAN-based and pitch-based carbon fibres, the fibres were oxidized in an electrolyte and characterized using the coulostatic method, X-ray photoelectron spectroscopy, laser Raman spectroscopy, and X-ray diffraction. The interfacial bonding strength to an epoxy resin was evaluated based on the interlaminar shear strength (ILSS). The results showed a good correlation between the differential double layer capacities, which were measured with the coulostatic method, and the ILSS values of PAN-based high tensile strength carbon fibres (PAN-HTCFs), PAN-based high modulus carbon fibres (PAN-HMCFs), and pitch-based high modulus carbon fibres (pitch-HMCFs). Their morphologies for the anodic oxidation were as follows: PAN-HTCFs are anodized homogeneously; pitch-HMCFs are selectively oxidized and promote crevice etching; and PAN-HMCFs resist crevice etching due to the many defects in the hexagonal network.     

Voltammetric separation of dopamine and ascorbic acid with graphite electrodes modified with ultrafine TiO2

In this paper, a new method was introduced to separate dopamine and ascorbic acid simultaneously. When a graphite electrode was modified with nanosized TiO₂ powder, it exerted little influence on the redox behavior of dopamine, but led to the anodic potential of ascorbic acid to move negatively which enlarged the anodic separation potential between dopamine and ascorbic acid to some extent. Better separation could be achieved with bare C and TiO₂ modified electrode at higher scan rate. The catalytical ability of nanosized metal oxide on the voltammetric behavior of dopamine and ascorbic acid was discussed as well.     

Electrochemical oxidation of histamine and serotonin at highly boron-doped diamond electrodes

The electrochemistry of histamine and serotonin in neutral aqueous media (pH 7.2) was investigated using polycrystalline, boron-doped diamond thin-film electrodes. Cyclic voltammetry, hydrodynamic voltammetry, and flow injection analysis (FIA) with amperometric detection were used to study the oxidation reactions. Comparison experiments were carried out using polished glassy carbon (GC) electrodes. At diamond electrodes, highly reproducible and well-defined cyclic voltammograms were obtained for histamine with a peak potential at 1.40 V vs SCE. The voltammetric signal-to-background ratios obtained at diamond were 1 order of magnitude higher than those obtained for GC electrodes at and above 100 microM analyte concentrations. A linear dynamic range of 3-4 orders of magnitude and a detection limit of 1 microM were observed in the voltammetric measurements. Well-defined sweep rate-dependent voltammograms were also obtained for 5-hydroxytryptamine (5-HT). The characteristics of the voltammogram indicated lack of adsorption of its oxidation products on the surface. No fouling or deactivation of the electrode was observed within the experimental time of several hours. A detection limit of 0.5 microM (signal-to-noise ratio 13.8) for histamine was obtained by use of the FIA technique with a diamond electrode. A remarkably low detection limit (10 nM) was obtained for 5-HT on diamond by the same method. Diamond electrodes exhibited a linear dynamic range from 10 nM to 100 microM for 5-HT determination and a range of 0.5-100 microM for histamine determination. The FIA response was very reproducible from film to film, and the response variability was below 7% at the actual detection limits.     

Electrocatalytic reduction of chloramphenicol at multiwall carbon nanotube-modified electrodes

A multiwall carbon nanotube-modified glassy carbon (GC) electrode was employed for the investigation of chloramphenicol (CAP) reduction. Carbon nanotube coating can greatly lower the overpotential of the electrochemical reduction of CAP and promote the electrode reaction. CAP undergoes an irreversible reduction process in phosphate buffer by the modified electrode. The reduction peak current (Ip) was significantly increased. Effects of some important factors, including pH, scan rate, and amount of modifier, on the determination of CAP were investigated. In the range of 3 x 10(-7) to 1.2 x 10(-5) M, the reduction peak current (Ip) has a good linear relationship with the concentration of CAP. When the signal-to-noise ratio is 3, the detection limit is 4.5 x 10(-8) M. The relative standard deviation of 10 measurements for 3 x 10(-6) M CAP is 5.3%, suggesting an excellent reproducibility of the modified electrode. Interfering experiments show that the modified electrode has excellent selectivity for the detection of CAP. The modified electrode was used to determine CAP in eyedrops, and the recoveries were approximately 100%.     

Catalytic oxidation and flow detection of carbohydrates at ruthenium dioxide modified electrodes

Ruthenium dioxide (RuO2) containing carbon paste electrodes exhibiting electrocatalytic response toward carbohydrates are described. The electrocatalytic behavior is exploited for developing a highly stable and sensitive flow detection scheme for carbohydrates at a low and fixed potential (+0.4 V vs Ag/AgCl). The effects of pH, flow rate, operating potential, surface "loading", concentration, and other variables are explored. The electrode response was stable for more than 48 h, with a signal loss of less than 10% over this period. The detection limits at the picomole level and a relative standard deviation of 1.2% (n = 72) are reported. Electrocatalytic oxidation is described also for related polyhydroxyl compounds (aldonic and aldaric acids and alditols).     

Direct electrochemical oxidation of disulfides at anodically pretreated boron-doped diamond electrodes

Anodically oxidized diamond electrodes have been used to oxidize disulfides, thiols, and methionine in aqueous acidic media and tested for amperometric detection of these compounds after chromatographic separation. Cyclic voltammetric signals for 1 mM glutathione disulfide (GSSG) were observed at 1.39 and 1.84 V vs SCE, the values being less positive than those of its as-deposited counterpart as well as glassy carbon electrode. The voltammetric and chronocoulometric results have indicated the high stability of the electrode with negligible adsorption. A positive shift in the peak potential with increasing pH indicated the attractive electrostatic interaction between the anodically oxidized diamond surface and the positively charged GSSG in acidic media that promoted its analytical performance. The results of the electrolysis experiments of disulfides and thiols showed that the oxidation reaction mechanism of glutathione (GSH) and GSSG involves oxygen transfer. Following separation by liquid chromatography (LC), the determination of both GSH and GSSG in rat whole blood was achieved at a constant potential (1.50 V vs Ag/AgCl), and the limits of detection for GSH and GSSG were found to be 1.4 nM (0.028 pmol) and 1.9 nM (0.037 pmol) with a linear calibration range up to 0.25 mM. These detection limits were much lower than those reported for the amperometry using Bi-PbO2 electrodes and LC-mass spectrometry, and the LC method using diamond electrodes were comparable with enzymatic assay in real sample analysis. The high response stability and reproducibility together with the possibility of regeneration of the electrode surface by on-line anodic treatment at 3 V for 30 min further support the applicability of anodically pretreated diamond for amperometric detection of disulfides.     

Multi-walled carbon nanotube modified carbon paste electrode as an electrochemical sensor for the determination of epinephrine in the presence of ascorbic acid and uric acid

A biocompatible electrochemical sensor for selective detection of epinephrine (EP) in the presence of 1000-fold excess of ascorbic acid (AA) and uric acid (UA) was fabricated by modifying the carbon paste electrode (CPE) with multi-walled carbon nanotubes (MWCNTs) using a casting method. The electro-catalytic activity of the modified electrode for the oxidation of EP was investigated. The current sensitivity of EP was enhanced to about five times upon modification. A very minimum amount of modifier was used for modification. The voltammetric response of EP was well resolved from the responses of AA and UA. The electrochemical impedance spectroscopic (EIS) studies reveal the least charge transfer resistance for the modified electrode. The AA peak that is completely resolved from that of EP at higher concentrations of AA and the inability of the sensor to give an electrochemical response for AA below a concentration of 3.0 × 10^? 4 M makes it a unique electrochemical sensor for the detection of EP which is 100% free from the interference of AA. Two linear dynamic ranges of 1.0 × 10^? 4–1.0 × 10^? 5 and 1.0 × 10^? 5–5.0 × 10^? 7 M with a detection limit of 2.9 × 10^? 8 M were observed for EP at modified electrode. The practical utility of this modified electrode was demonstrated by detecting EP in spiked human blood serum and EP injection. The modified electrode is highly reproducible and stable with anti fouling effects.     

Corrosion behaviour of copper-reinforced carbon electrodes in dilute hydrochloric acid solutions

The corrosion behaviour of experimentally prepared copper-reinforced carbon electrodes in dilute hydrochloric acid is investigated. The electrodes are not only directly attacked by the acid, but they are also subjected to galvanic corrosion. The baking temperature and time are the most crucial processing variables. A minimum in the corrosion rate is always achieved when the electrodes are baked at 400 °C for 1.5 h, the level depending on the copper content. The corrosion resistance increases progressively with the baking temperature as long as the baking time is less than 1.5 h. Baking for more than 1.5 h results in increasing corrosion rate. The presence of copper increases the corrosion resistance of the prepared electrodes.     

Nanostructured carbon fiber disk electrodes for sensitive determinations of adenosine and uric acid

Nanostructured carbon fiber microdisk electrodes were prepared by a combination of mechanical polishing and electrolytic treatment, where the latter involved moderate oxidation of the surface, followed by a reduction. A high density of surface defects contributed to a high capacitance of the nanostructured electrodes. Facilitated proton transfer was observed at the nanostructured surface and was associated with cation-exchanged oxide defects. The nanostructured surfaces intercalated uric acid and adenosine and engaged in fast electron/proton transfer in the oxidation of both analytes. As a result, electrolytic treatment followed by fast-scan voltammetry determinations led to a sensitive response to both analytes in physiological buffers. The nanostructured electrodes showed remarkable stability and could be easily regenerated and reused. With long use, electrode activity decreased. Kinetic discrimination of the surface-mediated reaction of ascorbate was achieved at high scan rates.