Stop drilling procedure for fatigue life improvement

This paper investigated how the stop drilling procedure improved the crack initiation life and the total fatigue life in specimens of 6061-T651 aluminium alloy and AISI 304 stainless steel. The crack initiation life was the number of fatigue cycles initiating a 0.2 mm crack at a stophole edge. The larger the stophole diameter, the longer the crack initiation and total fatigue lives. The 2, 2.5, and 3 mm diameter stopholes improved the nonstop-drilled total fatigue life of the 6061-T651 specimen by 187%, 321%, and 443% and that of the AISI 304 specimen by 72%, 121%, and 174%. At each stophole diameter, the 6061-T651 crack initiation life improved over the AISI 304 counterpart because of lower values of the K_f factor and the ΔJ/ρ_c ratio.     

Threshold range and opening stress intensity factor in fatigue

The fatigue threshold, ΔK_th, is strongly influenced by the stress-ratio, ie by the loading conditions. Results for a Ti6A14V alloy show that a ΔK exists for non-propagating fatigue cracks which is independent of loading conditions. This ΔK is called the fatigue tolerance range and is denoted by ΔK^K. The fatigue tolerance range corresponds to that part of the ΔK_th during which the fatigue crack is open. Arguments that the fatigue tolerance range has to be explicitly incorporated in equations predicting fatigue crack growth rates are presented.     

Fatigue crack growth characteristics of rotor steels

Room temperature fatigue crack growth rate data were generated for Ni-Mo-V (ASTM A469, Cl-4), Cr-Mo-V (ASTM A470, Cl-8) and Ni-Cr-Mo-V (ASTM A471, Cl-4 and a 156,000 psi yield strength grade) rotor forging steels. Testing was conducted with WOL type compact toughness specimens and the results presented in terms of fracture mechanics parameters. Data show that the Ni-Cr-Mo-V steels exhibit slower fatigue crack growth rates at a given stress intensity range (ΔK) than do the Ni-Mo-V steels. In addition, the Cr-Mo-V steel was found to exhibit slower growth rates than the other alloys at ΔK levels below 40 ksi √in but somewhat foster rates at ΔK levels in excess of 45 ksi √in. The fatigue crack growth rate properties of the alloys studied conform to the generalized fracture mechanics crack growth rate law where da/dN = C₀ΔK^R. It was noted that the fatigue crack growth rate parameters n and C₀ tend to decrease and increase, respectively, with increasing material toughness, K_ic.     

The effect of the stress ratio on fatigue crack growth in a 3% NaCl solution

Corrosion fatigue crack growth tests have been carried out at various stress ratios for a low alloy steel SNCM 2 and type 304 stainless steel.

Measurements of the effective stress intensity factor range ratio U were performed to explain the effect of stress ratio R.

The corrosive environment decreased da/dN at R = 0.1, 0.4 and little affected da/dN at R = 0.9 for SNCM 2 and increased da/dN at all R ratios for SUS 304.

It was confirmed that there exists a threshold stress intensity factor ΔK_thCF in 3% NaCl solution for both materials tested.

The corrosive environment decreased ΔK_thCF for all conditions tested except at R = 0.1 and 0.4 for SNCM 2, where ΔK_thCF-values were nearly equal to ΔK_th-values in air. ΔK_thCF/ΔK_th was 0.6 at R = 0.9 for SNCM 2 and 0.8, 0.5 and 0.7 at R = 0.1, 0.7 and 0.9 for SUS 304, respectively.

It was shown that the complicated effect of stress ratios on crack growth for SNCM 2 can be explained using effective stress intensity factor ΔK_eff.     

The use of ΔK when examining microstructural effects on small fatigue crack growth

The behaviour of small fatigue cracks has been studied in the Al---Li---Cu---Mg---Zr alloy 8090. It was found that the crack inclination normal to the surface of the specimen made crack deflections and kinking in the plane of the specimen surface irrelevant to the crack driving force. The low closure levels associated with small fatigue cracks reduce the effect of microstructure on crack growth but this does not affect the ability of ΔK (stress intensity factor range) to detect microstructural influences. The use of ΔJ (J-integral range) as a correlating parameter reduced the differences between the data for long and short fatigue cracks. However, there was no evidence that ΔJ was superior at identifying microstructural effects. Similarly the effect of the higher-order terms on the value of ΔK was found to be minor. It is concluded that the use of ΔK is not likely to bias the microstructural effects and so ΔK may be used when examining microstructural effects on small fatigue crack growth.     

Temperature dependence of stage II fatigue crack growth rate

A critical assessment has been performed by compiling experimental data concerning the temperature dependence of stage II fatigue crack growth. For aluminium alloys, high strength steels, austenitic stainless steels and superalloys, the power coefficient, m, for the Paris relationship is temperature dependent and all ln(da/dN) vs ln(ΔK) curves cross at one point, designated as the pivot point (PP), which is a material-dependent parameter. The assumption is made that PP corresponds to a transition point for the fatigue crack growth mechanism.     

Relation between fatigue threshold and fatigue limit for surface-rolled specimens

After cylinder notch fatigue specimens of 40 CrNiMo steel were rolled, their fatigue limit increased by 41%. The rolled specimens did not fracture, even though they had been loaded for 10⁷ cycles under fatigue limit stress, but a non-propagating fatigue crack was generated. Thus the value of the fatigue limit depends on the fatigue threshold value ΔK_th of the metal of the rolled layer. Plastic deformation increased ΔK_th in these experiments. It can be inferred that ΔK_th of the rolled layer increases from the occurrence of plastic deformation and microvoids on the layer. Calculation of the effect of residual stress in the crack wake on the stress intensity factor ΔK indicates that residual compression stress decreases ΔK by 21.5 MPa √M. It was calculated that rolling induced both the length of the non-propagating crack and the increase of fatigue limit. The calculated values are in accord with experiment. Analysis and calculations indicate that the non-propagating crack is generated on the rolled layer. Thus the fatigue limit is improved because rolling produces residual compression stress in the layer (which decreases the stress intensity factor), and increases ΔK_th of the layer.     

Fatigue crack initiation and growth under mixed mode loading in aluminum alloys 2017-T3 and 7075-T6

Fatigue crack initiation and growth characteristics under mixed mode loading have been investigated on aluminum alloys 2017-T3 and 7075-T6, using a newly developed apparatus for mixed mode loading tests. In 2017-T3, the fatigue crack initiation and growth characteristics from a precrack under mixed mode loading are divided into three regions—shear mode growth, tensile mode growth and no growth—on the ΔK_I-ΔK_II plane. The shear mode growth is observed in the region expressed approximately by ΔK_II > 3MPa√m and ΔK_II/ΔK_I > 1.6. In 7075-T6, the condition of shear mode crack initiation is expressed by ΔK_II > 8 MPa√m and ΔK_II/ΔK_I > 1.6, and continuous crack growth in shear mode is observed only in the case of ΔK_I/ΔK_II, 0. The threshold condition of fatigue crack growth in tensile mode is described by the maximum tensile stress criterion, which is given by Δσ_θmax √2πr 1.6MPa√m, in both aluminum alloys. The direction of shear mode crack growth approaches the plane in which K_I decreases and K_II increases towards the maximum with crack growth. da/dN-ΔK_II relations of the curved cracks growing in shear mode under mixed mode loading agree well with the da/dN-ΔK_II relation of a straight crack under pure mode II loading.     

A new microcomputer-aided system for measuring fatigue crack propagation threshold and selecting testing parameters

A new mathematical model is proposed for measuring fatigue crack propagation (FCP) threshold by using K-decreasing and K-increasing method. The formulae for efficiently selecting load-variation coefficients and crack growth increments (Δa) , (Δa) , in the case of K-decreasing and K-increasing tests are given and a correct method for determining FCP rate in the near-threshold region is recommended. On the basis of the above-mentioned work, a personal microcomputer-aided system is set up and successfully used for the FCP rate measurement in Lc9 aluminum alloy in 3.5% NaCI salt water environment. Compared with other systems, this system can increase the measurement accuracy, shorten testing time and obtain more information. Furthermore, the hardware is inexpensive.     

The effect of short time post-weld heat treatment on the fatigue crack growth of 2205 duplex stainless steel welds

The influence of γ content and its morphology on the impact and fatigue crack growth behavior of 2205 duplex stainless steel (DSS) welds were studied in this work. Short time post-heating was able to effectively raise the γ content and the impact toughness of the weld. The variation in microstructures showed less influence on the fatigue crack growth rate (FCGR) of the steel plate and weld except in the low ΔK regime. In contrast, residual welding stresses played a more significant affection on the FCGR of the DSS weld than microstructural factors did. Plastic deformation induced martensitic transformation within a definitely thin layer was responsible for the difference in crack growth behavior between specimens in the low ΔK range. Coarse columnar structure was more likely to have tortuous crack path in comparison with the steel plate.     

Effects of corrosive environments on near-threshold fatigue crack growth behavior of T1-6A1-4V

The near-threshold fatigue crack growth behavior of Ti-6A1-4V alloy has been investigated in low O₂ steam (< 1 ppm), high O₂ steam (40ppm), and boiling water with various concentrations of Nad and/or Na₂₂SO₄. At load ratio (R) of 0.5, high O₂ steam increased the crack propagation rates in the threshold region, relative to low O₂ steam. However, at R = 0.8, the near-threshold crack growth rates in low and high O₂ steam were comparable. Values of threshold stress intensity range, ΔK_th, slightly increased with an increase in the concentration of NaCl in the solution. Varying solution pH from 5.0 to 10.0 in a 0.1 g NaCl plus 0.1 g Na₂SO₄ per 100ml H₂O solution had no effect on the rates of near-threshold crack propagation. Increasing the hydrazine level from 30 to 10⁷ ppb in the same salt solution also did not change the resistance to crack growth. Comparing the present results with the previous data on 403 stainless steel, the near-threshold crack propagation rate performance in Ti-6Al-4V alloy is superior to that in 403 steel in both the steam and salt solution environments.     

The growth of fatigue cracks through particulate sic reinforced aluminum alloys

Crack growth rates for large fatigue cracks in 12 variations of particulate silicon carbide reinforced aluminum alloy composites have been measured. Composites with seven different matrix alloys were tested, four of which were of precipitation hardening compositions, and those were tested in both as-extruded and peak aged conditions. Five of the materials were made by casting, ingot metallurgical methods and two of the alloys by mechanical alloying, powder metallurgical methods. For both manufacturing methods, primary fabrication was followed by hot extrusion. The fatigue crack growth curves exhibited an approximately linear, or Paris law, region, fitting the function da/dN = BΔK^s, and a threshold stress intensity factor, ΔK_th. As has been found for other materials, the coefficients B and s are correlated; for these composites In B= −16.4−2.1s. A correlation was also found between ΔK_th and s, and it was found possible to compute the magnitude of ΔK_th using a simple model for the threshold together with yield stress and SiC size and volume fraction. These results were explained using a relationship between ΔK_th and crack closure determined previously for unreinforced aluminum alloys. The path of fatigue crack growth is through the matrix for these composites, and SiC has the effect of altering the slip distance, therefore, the plasticity accompanying fatigue cracks. It was shown that all the crack growth rate curves were reduced to one equation having the form da/dN = B'ΔK_eff^s' where B' = 6.5 × 10^-9m/cy and s' = 1.7. A partly theoretical method for predicting fatigue crack growth rates for untested composites is given. Fatigue crack surface roughness was measured and found to be described by a fractal dimension, but no correlation could be obtained between surface roughness parameters and ΔK_th.     

Effects of welding residual stresses on fatigue crack growth behaviour in butt welds of a pipeline steel

In the present test the fatigue crack growth rate in the parent plate, weld and cross-bond regions was measured and the results were correlated with the stress intensity range ΔK and the effective stress intensity range ΔK_eff. It is indicated that the welding residual stresses strongly affect the crack growth rate. For the weld metal and cross-bond compact tension specimens in which crack growth is along the weld line the fatigue crack growth rate increases as the crack grows. However, for the T compact tension specimen in which crack growth is perpendicular to the weld line at a constant value of applied ΔK the crack growth rate initially decreases as the crack grows. Particularly, at a low constant value of applied ΔK the crack growth rate obviously decreases and the crack fails to grow after short crack growth. When the crack grows to intersect the welded zone, the fatigue crack growth rate gradually increases as the crack grows further. It is clear that the effect of welding residual stresses on the crack growth rate is related to the position of the crack and its orientation with respect to the weld line. Finally, the models of welding residual stress redistribution in the compact tension specimens with the growing crack and its influence on the fatigue crack closure are discussed. It appears that for a butt-welded joint one of the crack closure mechanisms may be considered by the bend or rotation deformation of crack faces due to the welding residual stress redistribution as the fatigue crack grows in the welded joint.     

Fatigue crack-growth characteristics of two magnesium alloys

Magnesium alloys are being increasingly used for engineering applications. Fatigue crack-growth data have therefore been obtained for a high strength magnesium-Zr alloy and a medium strength, weldable magnesium-Mn alloy. The results of tests on sheet material are presented in terms of the range of stress intensity factor ΔK. Critical values of ΔK necessary for fatigue crack growth ΔK_c were also obtained. The behaviour of the two alloys was similar; both rates of crack growth and ΔK_c were sensitive to mean stress. Fatigue crack growth was entirely on a 90° plane with no sign of the transition to crack growth or 45° planes usually observed in sheet materials. This was ascribed to the effects of preferred orientation of the crystal structure.     

Influence of R on effective stress range ratio and crack growth

The influence of stress ratio R and stress intensity range ΔK on crack closure and fatigue crack growth were studied. Crack closure and crack growth experiments were performed on 6063-T6 Al alloy. Crack closure stresses were measured using a surface-measurement technique with a COD gauge. The gauge was placed at different locations behind the crack tip, and it was found that the location of the gauge does not influence the closure load. The closure load was however found to be a function of R and ΔK. Fatigue crack growth rate is found to depend upon R, U and ΔK. A model for both U and da/dN has been developed.     

Shear lips on fatigue fractures in aluminium alloy sheet material

An analysis is made of shear lip width measurements and the transition of tensile mode fatigue cracks to shear mode fatigue cracks, as observed on fatigue crack surfaces of aluminium alloy sheet material. It could be shown that these phenomena were controlled by ΔK_eff, rather than K_max or ΔK. For crack growth in air the shear lip width was approximately proportional to (ΔK_eff)², but it was significantly larger than the estimated size of the reversed plastic zone. The initiation of shear lips, the transition from plane stress to plane strain along the crack front and the environmental effect on shear lips are briefly considered in the discussion.     

On the calculation of closure-free fatigue crack propagation data in monolithic metal alloys

A computational method is described for the determination of ΔK_b, corresponding to a fatigue crack growth rate of b/cyc, where b is the Burgers vector for a monolithic metal alloy. ΔK_b is found to be numerically equal to E√b for the case of closure-free crack growth behavior. Given that the closure-free FCP rate of many monolithic metals varies with ΔK³, the growth rate of metal alloys at ΔK ΔK_b is given by da/dN = (ΔK/E)³(1/√b. Excellent agreement is found between experimental and computed FCP data for the case of monolithic metal alloys. The limits of these relations for metal-matrix composites and ceramics are discussed.     

Statistical evaluation of fatigue crack propagation properties including threshold stress intensity factor

The relationship between fatigue crack propagation rate, da/dn, and range of stress intensity factor, ΔK, including threshold stress intensity factor, ΔK_th, is analyzed statistically. A non-linear equation, da/dn = C{(ΔK)^m-(ΔK_th)^m}, is fitted to the data by regression method to evaluate the 99% confidence intervals. Several experimental results on fatigue crack propagation properties of welded joints are compared by using these confidence intervals.     

Near-threshold fatigue crack growth at room temperature and an elevated temperature in Al---Li alloy 8090

The effects of slip distribution and crack tip shielding mechanisms on the near-threshold fatigue crack growth of the Al---Li alloy 8090 have been studied at both room temperature and an elevated temperature. The slip distribution has been varied by changing the distribution of the S phase, through prior stretching or by means of a duplex heat treatment. Fatigue crack growth (FCG) tests were conducted at a high stress ratio to reduce possible effects due to crack closure.

At room temperature the changes in FCG rates are interpreted as arising from the changes in the degree of planarity of slip in the materials.

At 150°C, the microstructural changes due to the long exposure to elevated temperature appear to dominate the effects observed. At lower ΔK, where the time at temperature is greatest, lower ΔK thresholds than those found at room temperature are obtained. These have been attributed to increased slip homogenization due to the increased precipitation and coarsening of the incoherent S phase together with loss of toughness due to the growth of coarse grain boundary phases and the formation of the associated δ′ precipitate free zone.

At higher ΔK, where the time at temperature is low and microstructural changes are minimal, slower FCG rates than those found at room temperature are obtaine. These are explained in terms of increased crack tip shielding which arises because of the increase in tortuosity of the crack path, the increased slip homogenization and the climb and cross-slip within the crack tip plastic zone.     

Creep crack growth behaviour in air and sodium for an unstabilized austenitic stainless steel and assessment of evaluation concepts

The austenitic stainless steels used for permanent structures in the heat transfer systems of liquid metal fast breeder reactors (LMFBR's) are subjected to flowing sodium at elevated temperatures. During this exposure to sodium environment the structural materials can undergo compositional and microstructural changes which could alter the mechanical behaviour as compared to air. An investigation of creep crack growth in air and flowing liquid sodium was performed on the austenitic stainless steel X6 CrNi 18 11 (similar to AISI 304 ss) under constant load at 823 K using compact tension specimens. The sodium conditions are characterized by an upstream position in a non-isothermal loop with a temperature gradient of 170 K. The experimental data are evaluated correlating the crack growth rate with the net section stress σ_net, the stress intensity factor K_Q, and the energy rate integral C^*, respectively.