Preparation of TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> hollow spheres and their activity in methylene blue photodecomposition

PSA [poly-(styrene-methyl acrylic acid)] latex particle has been taken into account as template material in SiO₂ hollow spheres preparation. TiO₂-doped SiO₂ hollow spheres were obtained by using the appropriate amount of Ti(SO₄)₂ solution on SiO₂ hollow spheres. The photodecomposition of the MB (methylene blue) was evaluated on these TiO₂-doped SiO₂ hollow spheres under UV light irradiation. The catalyst samples were characterized by XRD, UV-DRS, SEM and BET. A TiO₂-doped SiO₂ hollow sphere has shown higher surface area in comparison with pure TiO₂ hollow spheres. The 40 wt% TiO₂-doped SiO₂ hollow sphere has been found as the most active catalyst compared with the others in the process of photodecomposition of MB (methylene blue). The BET surface area of this sample was found to be 377.6 m²g⁻¹. The photodegradation rate of MB using the TiO₂-doped SiO₂ catalyst was much higher than that of pure TiO₂ hollow spheres.     

Comparison of Different Photocatalytic Systems for Acetonitrile Degradation in Gas–solid Regime

Photocatalytic degradation of acetonitrile was carried out in gas–solid regime by using two commercial TiO₂ samples (Merck and Degussa P25) irradiated in two continuous annular photoreactors. The inlet gas flow consisted of oxygen, nitrogen, acetonitrile and water vapours. The influence on the photodegradation rate of gas flow rate, acetonitrile, oxygen and water concentrations and photon flux was investigated. The degradation products of acetonitrile were carbon dioxide and hydrogen cyanide. The photocatalysts performance was not affected by the presence or absence of water vapour in the reacting mixture. The Langmuir–Hinshelwood model describes adequately the photoreactivity results and provides the values of kinetic and equilibrium adsorption constants. FT-IR spectroscopy was used to investigate the adsorption patterns and photo-oxidation intermediates of acetonitrile on fully hydrated surface of TiO₂ powders. Acetonitrile was adsorbed on Ti⁴⁺ surface ions and hydroxyl groups for both types of TiO₂. In the absence of UV light this interaction was completely reversible for Merck catalyst whereas for Degussa P25 part of adsorbed acetonitrile molecules reacted to form acetamide-like species.     

Effect of Pretreatment Atmosphere on CuO/TiO2 Activities in NO + CO Reaction

Using TiO₂ as carrier, CuO/TiO₂ catalysts with different CuO loading were prepared by the impregnation method. The catalytic activities in NO+CO reaction were examined with a micro-reactor gas chromatography reaction system and the methods of TPR, XPS and NO-TPD. It was found that the catalytic activities were affected by pretreatment atmosphere, i.e. H₂ atmosphere > reduction–reoxidation > 10%CO/He > reaction gas (fresh sample). NO decomposition was better by low-valence Cu species than by high-valence Cu species, i.e. Cu⁰>Cu⁺>Cu²⁺. The XPS results indicated that Cu species on CuO/TiO₂ were Cu⁰, Cu⁺, normal Cu²⁺(Cu²⁺(I)) and chain-structured Cu²⁺(Cu²⁺(II)) as –Cu–O–Ti–O–. The activities of Cu²⁺(II) were much higher than that of Cu²⁺(I), but both species were very unstable in the reaction atmosphere and easily reduced by CO, which accounted for the variable activities of fresh catalysts with increasing reaction temperature. In NO+CO reaction, the redox process was a cycle of Cu⁺–Cu²⁺(I) at low reaction temperature but was a cycle of Cu⁰–Cu⁺ at high reaction temperature. As shown by NO-TPD, high catalytic activities could be attributed to the following factors, e.g. oxygen caves on the catalyst’s surface after pretreatment with H₂ and reduction–reoxidation, formation of Cu⁰ after pretreatment with H₂, and increment of Cu species dispersion and formation of Cu²⁺(II) after pretreatment with reduction–reoxidation.     

Fe effect on the optical properties of TiO2:Fe2O3 nanostructured composites supported on SiO2 microsphere assemblies

The effect of Fe ion concentration on the morphological, structural, and optical properties of TiO₂ films supported on silica (SiO₂) opals has been studied. TiO₂:Fe₂O₃ films were prepared by the sol-gel method in combination with a vertical dip coating procedure; precursor solutions of Ti and Fe were deposited on a monolayer of SiO₂ opals previously deposited on a glass substrate by the same procedure. After the dip coating process has been carried out, the samples were thermally treated to obtain the TiO₂:Fe₂O₃/SiO₂ composites at the Fe ion concentrations of 1, 3, and 5 wt%. Scanning electron microscopy (SEM) micrographs show the formation of colloidal silica microspheres of about 50 nm diameter autoensembled in a hexagonal close-packed fashion. Although the X-ray diffractograms show no significant effect of Fe ion concentration on the crystal structure of TiO₂, the μ-Raman and reflectance spectra do show that the intensity of a phonon vibration mode and the energy bandgap of TiO₂ decrease as the Fe⁺³ ion concentration increases.     

Photocatalytic Destruction of a Thiosulfonate

This paper presents experimental and quantum chemical consideration of photocatalytic and photochemical transformations in acetonitrile of CH₃C₆H₄S(O₂)SCH₂CH₂N(iPr)₂ (diisopropylaminoethyl 4-methylbenzenethiosulfonate, DAMT), an imitant of chemical agent VX with close structural properties and ionization energy. Diisopropylaminoethyl disulfide and 4-methylbenzenesulfonic acid were detected as major products of photocatalytic and photochemical degradation. Photocatalytic degradation stopped at about 60% DAMT conversion due to acidification of the system. Photochemical degradation proceeded slower but to a higher conversion since DAMT protonation did not stop photolysis completely. DAMT^{· +} forms at the first step of photocatalytic degradation, then it splits into CH₃C₆H₄SO₂^· and SCH₂CH₂N⁺(iPr)₂. The former fragment transforms into sulfonic acid and the latter decomposes into SCH₂ and CH₂N⁺(iPr)₂ in the absence of TiO₂, the route observed in mass spectrometry. However it is stable in adsorbed state on the TiO₂ surface and after reduction with photogenerated electron recombines to produce the disulfide product. The results suggest that photocatalytic and photolytic detoxification of VX is possible provided conditions are adjusted for its complete conversion.     

Impact of supercritical drying and heat treatment on physical properties of titania/silica aerogel monolithic and its applications

TiO₂–SiO₂ monolithic aerogels were homogeneously prepared using sol–gel method. Critical point of drying of TiO₂–SiO₂ gels with ethanol was studied for 30, 60, 90 and 120 min. Subsequently, the gels were dried with supercritical ethanol, resulting in amorphous aerogels that crystallized following heat treatment at 550 °C from 1 to 5 h. The TiO₂–SiO₂ aerogels were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM) and surface area measurements. The molar ratio of SiO₂:TiO₂ was 6 and the synthetic strategy revealed that TiO₂–SiO₂ aerogel, had a surface area 868 m²/g, particle size 40 nm, density 0.17 g/cm³ and 80% porosity. The finding indicated that from economic point of view, TiO₂–SiO₂ gel should be supercritical dried for 30 min and heat-treated for 5 h. The TiO₂–SiO₂ aerogel monoliths photocatalyst synthesized using sol–gel method provided insight into the characteristics that make a photocatalyst material well-suited for photodegradation of phenol and cyanide in an industrial waste stream containing Cl⁻, S²⁻ and NH₄⁺. Interestingly, after multiple reuse cycles (i.e. ≥7), photodegradation systems with regenerated photocatalyst showed a slightly decreasing of photoactivity 2–4%. The overall kinetics of photodegradation of either phenol or cyanide using TiO₂–SiO₂ aerogel photocatalyst was found to be of first order.     

Photocatalytic Properties of Silica-supported TiO2

TiO₂ supported on SiO₂ surface is effective on the recovery of photocatalyst, morphological control, and coating on the substrate. Furthermore, it shows much higher photocatalytic activity than pure TiO₂. The silica support is quite influential on the surface properties of TiO₂ supported on SiO₂. The enhanced photocatalytic activity of TiO₂–SiO₂ could be explained by the effects of surface area, adsorption, band-gap energy and local structure. However, it is difficult to say which one is the most important factor responsible for the photocatalytic property of TiO₂–SiO₂. For example, the reduction of particle size could effect on both of the surface area and band-gap energy. And, Ti–O–Si bonds could modify the band-gap energy and local structure. Therefore, the photocatalytic properties of TiO₂–SiO₂ should be expressed by sum of many factors such as surface area, adsorption, band-gap energy and local structure.     

Synergistic effects of doped Fe3+ and deposited Au on improving the photocatalytic activity of TiO2

Fe³⁺ doped together with Au deposited TiO₂ (Au/Fe³⁺–TiO₂) was successfully prepared, which shows excellent photocatalytic activity for degradation of methyl orange (MO) under both UV and visible light (λ > 420 nm) illumination. Fe³⁺ has been confirmed by EPR to substitute for Ti⁴⁺ in the TiO₂ lattice, and Au exists as Au⁰ on the surface of the photocatalyst indicated by the results of XRD. Fe³⁺ and Au have synergistic effects on improving the photocatalytic activity of TiO₂. A proposed mechanism concerning the synergistic effects is discussed to explain the improvement of the photocatalytic activities.     

A mesoporous SiO2 intermediate layer for improving light propagation in a bundled tube photoreactor

A photoreactor comprising a bundle of TiO₂-coated quartz tubes was studied by varying its tube wall thickness and tube configuration as well as introducing a mesoporous SiO₂ intermediate layer between the TiO₂ coating and quartz tube. The bundled tube photoreactor (BTP) performance was assessed based on tube light propagation and photocatalytic degradation rate of ethylene. Increasing the tube wall thickness improved the tube light propagation and the degradation rate of ethylene. An array of eight 6-mm tubes was found to be the best BTP configuration in this work. The findings from varying the tube configuration suggested an effectively illuminated surface area as a second important parameter to consider when comparing different BTP performances. Introducing a mesoporous SiO₂ intermediate layer with a thickness between 210 and 400 nm between the TiO₂ coating and quartz tube improved not only the tube light propagation but also the ethylene photocatalytic degradation rate by up to 70%. This improvement was attributed to controlled light refraction from the quartz tube, which can be achieved under the conditions of frustrated total internal reflection.     

Facile synthesis of mesoporous Ag-loaded TiO2 thin film and its photocatalytic properties

Ag nanoparticles highly dispersed into TiO₂ thin films are synthesized via a remarkably simple one-pot route in the presence of a P123 triblock copolymer as template directing and reducing agents, where the reduction of Ag⁺ to Ag⁰ by in situ heat-induced reduction through the oxidation of template at 400 °C and the controlled polymerization of TiO₂ take place simultaneously. The obtained mesoporous Ag/TiO₂ films deposited on soda-lime glass were optically transparent and crack-free. SEM and Kr adsorption clearly prove that Ag/TiO₂ films at different Ag contents are mesoporous with large surface area and regularly ordered mesopores and the thickness of the obtained films is ∼280 ± 20 nm. The pristine TiO₂ film exhibits a specific surface area of 63 cm²/cm² and specific pore volume of 0.013 mm³/cm² that it is decreased to 42 cm²/cm² and 0.010 mm³/cm² respectively as a result of Ag-loaded mesoporous TiO₂. The newly prepared photocatalysts Ag/TiO₂ films were evaluated for their photocatalytic degradation of 2-chlorophenol as a model reaction. It was found that the meso-ordered Ag/TiO₂ films are more photoactive 8 times than nonporous commercial photocatalysts Pilkington Glass Activ™. The recycling tests indicated that Ag/TiO₂ films was quite stable during that liquid-solid heterogeneous photocatalysis since no significant decrease in activity was observed even after being used repetitively for 10 times, showing a good potential in practical application. In general, the cubic mesoporous Ag/TiO₂ nanocomposites are stable and can be recycled without loss of their photochemical activity.     

Pd/Pt on Ti-containing Mixed Oxides as Dearomatization Catalysts: Physico-chemical Characterization and Activity

Pd/Pt supported on pure and doped TiO₂ (TiO₂–WO₃ and TiO₂–WO₃–SiO₂) were prepared and characterized by different techniques (XPS, TEM, XRD, H₂-TPR and TPD of ammonia). These catalysts were investigated in the hydrogenation of tetralin at 6.0 MPa, checking also their thio-tolerance by feeding increasing amounts of dibenzothiophene (DBT, 300 and 1000 wt ppm). The catalytic activity followed the order: Pd/Pt–TiO₂ > Pd/Pt–TiO₂–WO₃–SiO₂ > Pd/Pt–TiO₂–WO₃, evidencing a negative role of a second oxide inside TiO₂. The Pd/Pt–TiO₂ catalyst showed high activity regardless of reaction conditions (temperature, contact time, H₂/tetralin ratio) together with a good thio-tolerance up to 300 wt ppm of DBT.     

Benefits of Usage of Immobilized Silver Nanoparticles as Pseudomonas aeruginosa Antibiofilm Factors

The aim of this study was to assess the beneficial inhibitory effect of silver nanoparticles immobilized on SiO₂ or TiO₂ on biofilm formation by Pseudomonas aeruginosa—one of the most dangerous pathogens isolated from urine and bronchoalveolar lavage fluid of patients hospitalized in intensive care units. Pure and silver doped nanoparticles of SiO₂ and TiO₂ were prepared using a novel modified sol-gel method. Ten clinical strains of P. aeruginosa and the reference PAO1 strain were used. The minimal inhibitory concentration (MIC) was determined by the broth microdilution method. The minimal biofilm inhibitory concentration (MBIC) and biofilm formation were assessed by colorimetric assay. Bacterial enumeration was used to assess the viability of bacteria in the biofilm. Silver nanoparticles immobilized on the SiO₂ and TiO₂ indicated high antibacterial efficacy against P. aeruginosa planktonic and biofilm cultures. TiO₂/Ag⁰ showed a better bactericidal effect than SiO₂/Ag⁰. Our results indicate that the inorganic compounds (SiO₂, TiO₂) after nanotechnological modification may be successfully used as antibacterial agents against multidrug-resistant P. aeruginosa strains.     

Preparation and characterization of SO42-/TiO2 and S2O82-/TiO2 catalysts

Nanosized solid superacids SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂, as well as MCM-41-supported SO₄ ²⁻/ZrO₂, were prepared. Their structures, acidities, and catalytic activities were investigated and compared using XRD, N₂ adsorption-desorption, and in situ FTIR-pyridine adsorption, as well as an evaluation reaction with pseudoionone cyclization. The results showed that SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂ possess not only nanosized particles with diameters < 7.0 nm, a BET surface greater than 140 cm²/g and relatively regular mesostructures with pores around 4.0 nm, but also a pure anatase phase and strong acidity. Different from the Lewis acid nature of SO₄ ²⁻/ZrO₂/MCM-41, SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂ exhibit mainly Bronsted acidities. The strongest Bronsted acid sites were produced on SO₄ ²⁻/TiO₂ promoted with H₂SO₄, while Lewis acid sites on S₂O₈ ²⁻/TiO₂ even stronger than those on SO₄ ²⁻/ZrO₂/MCM-41 were generated when persulfate solution was used as sulfating agent. Because of their distinct acid natures, SO₄ ²⁻/TiO₂ and S₂O₈ ²⁻/TiO₂ exhibited catalytic activities for the cyclization of pseudoionone that were much higher than that of SO₄ ²⁻/ZrO₂/MCM-41. It can be concluded that the existence of more Br?nsted acid sites was favorable for proton participation in the cyclization reaction. Translated from Journal of Chemical Engineering of Chinese Universities, 2006, 20(2): 239–244 [译自: 高校化学工程学报]     

TiO2 photocatalyst loaded on hydrophobic Si3N4 support for efficient degradation of organics diluted in water

TiO₂ photocatalyst loaded on Si₃N₄ (TiO₂/Si₃N₄) was prepared by a conventional impregnation method and its photocatalytic performance for the degradation of organics (2-propanol) diluted in water was compared with that of TiO₂ photocatalysts (TiO₂/SiO₂, TiO₂/Al₂O₃, and TiO₂/SiC) loaded on various types of supports (SiO₂, Al₂O₃, and SiC). The formation of the well-crystallized anatase phase of TiO₂ was observed on the calcined TiO₂/Si₃N₄ photocatalyst, while a small anatase phase of TiO₂ was observed on the TiO₂/SiC photocatalyst and amorphous TiO₂ species was the main component on the TiO₂/SiO₂ and TiO₂/Al₂O₃ photocatalysts. The measurements of the water adsorption ability of photocatalysts indicated that the TiO₂/Si₃N₄ photocatalyst exhibited more hydrophobic surface properties in comparison to other support photocatalysts. Under UV-light irradiation, the TiO₂/Si₃N₄ photocatalyst decomposed 2-propanol diluted in water into acetone, CO₂, and H₂O, and finally, acetone was also decomposed into CO₂ and H₂O. The TiO₂/Si₃N₄ photocatalyst showed higher photocatalytic activity than TiO₂ photocatalyst loaded on other supports. The well-crystallized TiO₂ phase deposited on Si₃N₄ and the hydrophobic surface of Si₃N₄ support are important factors for the enhancement of photocatalytic activity for the degradation of organic compounds in liquid-phase reactions.     

Structural colors from TiO2/SiO2 multilayer flakes prepared by sol-gel process

Preparation of TiO₂/SiO₂ multilayer flakes and their application to decorative powders were investigated. In contrast to conventional products prepared through the multicoating of core platelets, the coreless TiO₂/SiO₂ multilayer flakes were prepared by detaching multilayer films from their substrates. These flakes exhibited structural colors, when the optical path length of both the TiO₂ and SiO₂ layers are adjusted to be one fourth of the wavelength of visible light. A multicoating of more than five layers resulted in the propagation of cracks, which prevented the preparation of thick flakes. Paint films fabricated using the multilayer flakes and acrylic resins showed reflectance spectra that were comparable with those obtained for multicoatings on substrates.     

Effect of silica on the microstructure and photocatalytic properties of titania

A series of TiO₂/SiO₂ composite with different Ti/Si ratios were prepared by sol–gel technique. The samples were characterized by different analytical techniques such as XRD, FT-IR, BET and XPS. Grain size of anatase TiO₂ calculated using Scherrer's formula was found to be in the range of 2.1–8.7 nm, and the content of anatase phase in TiO₂ ranges from 45% to 40.1%. The photocatalytic properties on methyl orange (MO) solution were also studied. The degradation rate of the composite is much higher than that of the pure TiO₂ in the same conditions.     

Oxidative carbonylation of methanol to dimethyl carbonate over CuCl/SiO2–TiO2 catalysts prepared by microwave heating: The effect of support composition

Copper(I) chloride catalysts with a loading of 20 wt%, supported on silica–titania mixed oxides with Si/Ti ratios of 1, 5, 10 and 50 were prepared by conventional and microwave heating methods and tested in the oxidative carbonylation of methanol to dimethyl carbonate (DMC). X-ray diffraction (XRD), nitrogen adsorption, X-ray photoelectron spectroscopy (XPS) and thermal gravimetric analysis (TGA) were used to examine the bulk and surface properties of the CuCl/SiO₂–TiO₂ catalysts. Quantum-chemical calculations were performed to explore the interaction of CuCl with the silica–titania support. Microwave heating showed some significant advantages over the conventional heating method, with markedly reduced preparation temperature and time, and provided improved catalytic activity in the oxidative carbonylation of methanol. The catalytic behavior of CuCl/SiO₂–TiO₂ in the test reaction studied was strongly dependent on the support composition. Incorporation of tetrahedral Ti(IV) species into the silica matrix could enhance the interaction of copper species with the oxide support. The improved catalytic performance of CuCl/SiO₂–TiO₂ in the DMC synthesis can be understood by the existence of the strong coordination interactions between the Cu⁺ centers of CuCl and the bridging oxygen atoms at the Si–O–Ti bonds in the silica–titania support.     

Synergistic effect of TiO2 and iron oxide supported on fluorocarbon films: Part 2: Long-term stability and influence of reaction parameters on photoactivated degradation of pollutants

The degradation of hydroquinone (HQ) and nalidixic acid (NA) mediated by TiO₂ and iron oxide immobilized on functionalized polyvinyl fluoride films (PVF^f–TiO₂–Fe oxide) in the presence of H₂O₂ under simulated solar light has been examined. The results show that the contribution of homogeneous photo-Fenton oxidation to the initial mineralization process was low. The degradation rates were not dependant of initial pH. Heterogeneous photocatalytic activity of PVF^f–TiO₂–Fe oxide was enhanced by increasing temperature, NaCl addition and by long-term utilization.The PVF^f–TiO₂–Fe oxide surface was characterized by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) at different states of utilization. Correlations between the catalyst surface composition and degradation kinetics are discussed. Long-term stability evaluated by repetitive pollutant degradations was outstanding. The presence of TiO₂ seems to (i) limit contact between polymer film and highly reactive radicals in the solution and (ii) act as a charge trap. Moreover, during the photocatalysis mediated by PVF^f–TiO₂–Fe oxide, some leaching of supported iron increased the amount of the top TiO₂ layer exposed to the light increasing the synergistic effects between the two oxides leading to enhanced pollutant degradation.     

Photocatalytic reactivity and diffusing OH radicals in the reaction medium containing TiO2 particles

The generation of OH radicals on UV-illuminated TiO₂ surface is mainly responsible for the photocatalytic oxidation of pollutants in various contaminated environmental media. Although the reactivity of OH radicals is largely limited within the surface region, the possibility of OH desorption and diffusion into the reaction medium has been often raised. This study provides several examples for the presence of diffusing OH radicals in aqueous solution and polymer matrix containing TiO₂ particles. The photocatalytic degradation rates of (CH₃)₄N⁺ in TiO₂ suspension were comparable between acidic and alkaline conditions, which could not be explained by a simple electrostatic surface charge model. From the present mechanistic study, it is suggested that the photocatalytic oxidation of (CH₃)₄N⁺ at acidic pH mainly proceeds through free OH radicals in the solution bulk, not on the surface of TiO₂. The diffusing OH radicals also played the role of main oxidants in the solid phase. The photolysis of TiO₂-embedded PVC composite films generated cavities around the imbedded TiO₂ particles and the development of cavity diameter continued even after the direct contact between the PVC and TiO₂ was prohibited. This implied that active oxygen species that were photogenerated on TiO₂ surface desorbed and diffused across a few micrometers to react with the polymer matrix.     

Cyclic voltammetry studies of TiO2 nanotube arrays electrode: Conductivity and reactivity in the presence of H and aqueous redox systems

In this paper, we use cyclic voltammetry to investigate the effect of protons on the conductivity and reactivity of TiO₂ nanotube array (NTA) electrodes in an aqueous redox system. The H⁺ ion can change the TiO₂ nanotube (anatase phase) surface states for electrons transfer. It can also act as an intermediate state for electron transfer to the acceptor species in the electrolyte surrounding the TiO₂. The higher the concentration of H⁺ ions in the aqueous electrolyte, the easier it is for the electrons transfer from the TiO₂ to the electrolyte oxidized species. The reduction is facile, with a similar reduction potential for various acceptor species, but re-oxidation is not possible. It is apparently an electrochemical reduction involving a single-proton transfer and single-electron transfer. Based on this conclusion, an electrode (PB/Au/TiO₂ NTAs) was fabricated by means of electrodeposition. The electrode used to detect hydrogen peroxide. The sensitivity of the detector is high, and its the detection limit can be as low as 100 nM.