异步轧制对硅钢极薄带三次再结晶的影响

分别采用同步和异步轧制将成品工业取向硅钢板冷轧到0.045～0.10mm,然后在纯氢气热处理炉中进行三次再结晶高温退火,研究轧制工艺参数对取向硅钢极薄带织构和磁性能的影响,探索异步轧制对硅钢极薄带三次再结晶行为影响机理.结果表明,采用异步轧制取向硅钢极薄带的磁性能优于同步轧制的;硅钢极薄带厚度愈薄,磁性能愈好,三次再结晶发展得越完善.     

异步轧制取向硅钢薄带的三次再结晶

采用带比为１．２的异步轧制及常规轧制，将０．３０ｍｍ厚的工业取向硅钢冷轧至０．１０ｍｍ，在普通氢气炉中退火。对退火薄带的再结晶组织、织构和磁性的研究表明：经异步轧制并在１１５℃退火的５ｈ中发生了三次再结晶，晶粒度１￣３ｍｍ、晶粒取向为｛１１０｝［００１］；与冷轧前板材相比，薄带的磁性明显改善；铁损下降了５１％，Ｂ８＝１．９７８Ｔ，Ｐ１３／５０＝０．３０ｍＷ·ｇ＾－１，Ｐ１７／５０＝０．７２ｍＷ·ｇ     

典型特殊制备技术对无取向电工钢织构的影响规律

电工钢又称硅钢,是一种重要的特殊钢,常被称作特殊钢中的“艺术品”,这主要是因为其加工制备流程复杂、性能影响因素繁多。其中无取向硅钢主要应用于旋转电磁场环境,为了获得优良的软磁性能,需要形成较多的{100}等有利织构,为此研究人员进行了大量探索,近年来发现一些特殊制备技术在形成大量{100}等有利织构方面有显著效果。本文综述二次轧制、斜轧、异步轧制及双辊薄带连铸四种典型特殊制备技术对无取向硅钢再结晶织构的影响规律,发现二次轧制与双辊薄带连铸均能增强λ与高斯织构,并削弱γ织构,斜轧也会增强λ织构,但对γ织构影响不大,异速异步轧制能增强η织构,而异径异步轧制对再结晶织构却基本没有影响。最后,总结目前各项特殊制备技术存在的缺陷,并提出一些发展方向,如借助斜轧原理在常规冷轧中产生更多剪切带、利用异步轧制进行二次加工以均匀化磁感等,为后续无取向硅钢的工业生产提供更多参考。     

典型特殊制备技术对无取向电工钢织构的影响规律EICSCD

电工钢又称硅钢,是一种重要的特殊钢,常被称作特殊钢中的“艺术品”,这主要是因为其加工制备流程复杂、性能影响因素繁多。其中无取向硅钢主要应用于旋转电磁场环境,为了获得优良的软磁性能,需要形成较多的{100}等有利织构,为此研究人员进行了大量探索,近年来发现一些特殊制备技术在形成大量{100}等有利织构方面有显著效果。本文综述二次轧制、斜轧、异步轧制及双辊薄带连铸四种典型特殊制备技术对无取向硅钢再结晶织构的影响规律,发现二次轧制与双辊薄带连铸均能增强λ与高斯织构,并削弱γ织构,斜轧也会增强λ织构,但对γ织构影响不大,异速异步轧制能增强η织构,而异径异步轧制对再结晶织构却基本没有影响。最后,总结目前各项特殊制备技术存在的缺陷,并提出一些发展方向,如借助斜轧原理在常规冷轧中产生更多剪切带、利用异步轧制进行二次加工以均匀化磁感等,为后续无取向硅钢的工业生产提供更多参考。     

形变模式对3104铝合金板微取向流变行为的影响

探讨了不同形变模式(同步轧制、异步轧制和双向异步轧制)对3104铝合金板微取向流变的影响.对各主要冷轧织构组分:Brass({110}〈112〉)、S({123}〈634〉)、R/S({124}〈211〉)、Goss({110}〈001〉)和Copper({112}〈111〉),在三维取向空间的取向密度ω(g)沿板厚的分布进行了定量测定.结果表明:同步轧制时,各层织构组分取向密度呈对称分布;异步轧制与双向异步轧制时,各织构组分与传统的同步轧制的织构组分相同,只是表层各织构组分的强度级别明显提高,沿着轧板的厚度方向呈非对称分布;双向异步轧制下,除各层的织构组分取向密度略有变化外,基本与异步轧制相同.这种巨大的差异,主要是由于异步轧制时,搓轧区剪切应力的大小和方向不同,造成金属微取向流变行为的差异所致.     

轧制法制备低铁损高磁感6.4%(质量分数)硅钢及其织构演变

采用轧制法制备出具有低铁损高磁感0.23mm厚6.4%(质量分数)Si高硅钢。沿轧制方向的最终磁性能为B8=1.474 T,B50=1.714 T;P10/50=0.30W/kg,P15/50=0.88W/kg。利用X射线衍射及背散射电子衍射(EBSD)技术分析了高硅钢在轧制及退火过程中的织构演变过程。结果表明,通过采用大压下率热轧,确保热轧板次表层中产生更多的高斯织构,随后进行遗传;温轧板中粗大的晶粒有利于冷轧剪切带的形成;冷轧板经脱碳退火后生成强{210}〈001〉织构及次表层较强的高斯织构是在轧向上获得高磁感的原因,归因于其在{111}〈112〉冷轧形变晶粒内的剪切带优先形核并长大;最终退火后虽出现了随机取向,但以{310}〈001〉织构为代表的η织构得以保留并且增强,进一步提高了磁感。随着退火温度的升高及保温时间的延长,高硅钢薄板晶粒尺寸不断增大,铁损明显降低。     

轧制复合法制备硅浓度梯度高硅钢薄带的织构演变

采用"热轧复合+冷轧减薄+退火"方法成功制备了0.20mm厚的硅浓度梯度高硅钢薄带,并采用SEM和X射线衍射技术对制备过程中组织和织构演变进行了研究。热轧复合板微观组织呈明显层状分布,复合界面为紧密冶金结合且经过83%的大冷轧变形未开裂。热轧和冷轧复合板带中均形成强α和γ织构,再结晶退火后形成强γ织构。冷轧和退火织构沿板厚呈显著的梯度分布特征,其主要来自于复合界面两侧硅浓度和初始热轧织构的差异性以及冷变形的不均匀性。     

冷轧压下率及初始高斯晶粒取向度对超薄取向硅钢织构演变与磁性能的影响

以不同高斯取向度的取向硅钢成品板为初始原料,采用一次冷轧法制备0.06~0.12mm厚的取向硅钢薄带。利用EBSD取向成像技术研究冷轧压下率以及初始高斯晶粒取向度对超薄取向硅钢织构演变与磁性能的影响。结果表明:随着冷轧压下率增大和厚度减小,退火后再结晶织构增强,当压下率为70%时,再结晶织构中RD∥〈001〉织构最锋锐,磁性能最佳;初始样品高斯取向度越高,制备的薄带样品磁性能越好;因此,生产高性能的取向硅钢薄带应选用初始高斯晶粒取向度较高的成品板。     

轧制方式对6016铝合金薄板组织和塑性各向异性的影响EI北大核心CSCD

利用凸耳实验、X射线衍射仪、EBSD等手段研究了热轧退火后常规轧制(NR)、横向轧制(TR)、交叉轧制(AR)等轧制方式对6016铝合金组织和平面各向异性的影响。结果表明:热轧退火后6016铝合金形成了强烈的立方织构{100}〈001〉。NR,TR冷轧板具有38%~44%的β取向线织构(主要包括铜,S,黄铜织构组分),但是AR冷轧后保留了12.2%的立方织构组分,变形织构组分很弱,因此AR冷轧板材制耳率最差,为7.1%。6016铝合金经过固溶处理后,NR,TR板形成9.12%强烈的立方织构,AR板的织构明显弱化且随机分布,因而AR再结晶退火板制耳率较NR,TR板的6%~8.16%明显降低,为2.76%。固溶处理后6016铝合金板的平均晶粒尺寸分别为23,25,22μm,AR轧制后合金的晶粒最小且分布最均匀。因此交叉轧制能有效改善6016铝合金板再结晶退火后的组织均匀性和塑性各向异性。     

取向硅钢生产工艺研究进展

结合取向硅钢的传统生产工艺,介绍其生产工艺研究的最新进展,重点介绍了薄板坯连铸连轧生产取向硅钢、异步轧制生产取向硅钢、双取向硅钢生产工艺、磁场退火生产取向硅钢和无抑制剂生产取向硅钢5种取向硅钢生产新工艺。这些新工艺均可在一定程度上提高取向硅钢的性能,有的已进入工业化实践阶段,有的已在实验室取得长足进步。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.