Hydrogen-induced decomposition in Pr(Co1−xCux)5 intermetallic compounds

Quasi-binary Pr(Co_1−xCu_x)₅ intermetallics with 0≤x≤1 were hydrogenated at elevated temperatures to precipitate Co and Cu and to study their mutual solubility. Low temperature hydrogenation was found to form a CaCu₅-type hydride containing about 1.6 hydrogen atoms per formula unit. Above 500 °C, the samples decompose into PrH_2.6, Cu and h.c.p.-Co. In the temperature range 330–450 °C, the CaCu₅-type hydrides coexist with the decomposed phases. Structural and magnetic measurements indicate that no solid solution are formed in Co-Cu decomposed phases. The magnetoresistance on both parent and hydrogenated samples does not exceed 0.5%.     

Properties of ytterbium and neodymium doped alkali metal yttrium double phosphates of the M3Y1−xLnx(PO4)2 type

The spectroscopic behaviour of the Nd³⁺ and Yb³⁺ doped alkaline metal yttrium double phosphates, M₃Y_1−xLn_x(PO₄)₂ (M=Na, Rb; x=0.01–0.3) were studied for both powder and single crystal samples. The high resolution absorption and emission spectra were measured in the visible and IR regions. Spectral changes with the Nd³⁺ and Yb³⁺ concentration were interpreted. The absorption strengths of the 4f–4f transitions were analysed and used to assess the structural modifications of the two double phosphates. Based on the 4 K absorption spectra the number of metal sites occupied by the dopants was investigated.

Strong emission from Na₃Y_1−xNd_x(PO₄)₂ involving the ⁴F_3/2→⁴I_9/2,⁴I_11/2,⁴I_13/2,⁴I_15/2 transitions were observed whereas the corresponding emission from the rubidium phosphate was presumably quenched by multiphonon processes due to the water molecules absorbed in the channel-like structure.

The IR spectra were used to assign the vibronic components of the electronic transitions. The Yb³⁺ emission bands were broadened depending on the Yb³⁺ concentration (1–10 mol%). The tentative energy level scheme of the ground and excited ²F_J (J=7/2, 5/2) levels was described.     

Preparation and structures of the La1−xKxCo1−xNbxO3 (x = 0–l) system

The La_1−xK_xCo_1−xNb_xO₃ system was performed by conventional solid state reaction technique using metal oxides. By DSC analysis, the activation energy of crystallization of the powders with x = 0.3 is 388.4 kJ/mol. The crystal structure of the compound reveals a transition from rhombohedral to cubic, and then to orthorhombic structure as the amount of the potassium niobate (KNbO₃) increases. It is found that the structure of the samples with x < 0.3 is similar to that of lanthanum cobaltate (LaCoO₃), while at the compositions with 0.7 ≥ x ≥ 0.3, the structure transforms to cubic. Finally, with x ≥ 0.7, the structures were similar to that of KNbO₃. According to the results of selected-area-diffraction (SAD) patterns and X-ray diffraction (XRD) identifications, the lattice parameters were calculated. The direction of superlattice structure along [2 1 0] was found for x = 0.5 as identified from SAD patterns. The dielectric constants were measured with cubic structure. Dielectric constant (K) decreases with increasing x.     

Magnetic entropy change in polycrystalline La1−xKxMnO3 perovskites

Polycrystalline samples of potassium doped lanthanum manganites having nanometric crystallite size have been synthesized by pyrophoric method. The Curie temperature (T_C) of the prepared samples is found to be strongly dependent on K content and spans between 260 and 309 K. Close to T_C, large change in magnetic entropy has been observed in all the samples. The maximum magnetic entropy change observed for samples with different concentration of K, exhibits a linear dependence with the applied magnetic field. Adiabatic temperature change at T_C at 1 T also increases with K doping and attains a maximum of 2.1 K for La_0.85K_0.15MnO₃. Estimated relative cooling power of La_1−xK_xMnO₃ compounds is nearly one-third of pure Gd. In addition to the tuneability of T_C between 260 and 310 K, higher chemical stability, lower eddy current heating and inexpensive preparation technique; the magnetic entropy change in La_0.85K_0.15MnO₃ compound at 1 T magnetic field is found to be 3.00 J/kg K and is 89% to that known for the prototype magnetic refrigerant (pure Gd). Our result on magnetocaloric properties suggests that La_1−xK_xMnO₃ compounds are attractive as a possible refrigerant for near room temperature magnetic refrigeration.     

Crystal fields in (La1−xGdx)OCl:Eu solid solutions

The formation of cation solid solution in the (La_1−xGd_x)OCl:Eu³⁺ (0≤x_Gd≤1; Δx_Gd=0.1) series was studied by photoluminescence spectroscopy. The luminescence from the ⁵D_0–2 to the ⁷F_0–4 levels of the Eu³⁺ ion in the (La_1−xGd_x)OCl series was recorded at 77 K by using argon ion laser excitation (457.9 nm). The interpretation of the spectra according to the C_4v site symmetry of the Eu³⁺ ion in the tetragonal PbFCl-type structure yielded nearly complete sets (18 to 19 levels) for the ⁷F_0–4 levels. Simulations of the Stark level schemes were carried out with the aid of a phenomenological c.f. theory utilizing the five non-zero c.f. B_q^k parameters (B₀², B₀⁴, B₄⁴, B₀⁶ and B₄⁶) allowed for the C_4v site symmetry. By using the calculated c.f. parameter sets a quantitative measure was obtained to monitor the formation of cation solid solutions. The strength of the c.f. effect was estimated with the c.f. strength parameters S and S^k (k=2, 4 and 6). The c.f. parameter sets reproduced the experimental ⁷F_J (J=0–4) energy level schemes with the rms deviations between 4 and 11 cm⁻¹. The individual parameters as well as the c.f. strength parameters were found to evolve in a smooth manner indicating complete solid solubility in the (La_1−xGd_x)OCl series. Some local distortions from the C_4v symmetry — probably of long range—leading to the splitting of the ⁷F₁ doubly degenerate E level were observed, however.     

Synthesis and properties of lithium ion conductors Li3−2x(Sc1−xZrx)2(PO4)3

Lithium ion conductors, Li_3−2x(Sc_1−xZr_x)₂(PO₄)₃ (0 x 0.3), were prepared by a solid-state reaction. TG–DTA analysis indicated no phase transition in the samples with x superior to 0.05. X-ray powder diffraction analysis of these samples clearly showed the stabilization of a superionic conduction phase at room temperature with an orthorhombic system Pbcn. The highest conductivity was observed for the sample with x=0.05, and ascribed to the stabilization of the superionic conduction phase and the introduction of vacancies on the Li⁺ sites by substituting Zr⁴⁺ for Sc³.     

Crystal structure of the new ternary aluminide CeRu3−xAl10+x (x = 0.17)

A large and transparent Yb³⁺:GdYCOB crystal with dimensions up to 30 mm× 58 mm have been grown by the Czochralski method. The spectral properties of Yb³⁺:GdYCOB crystal has been investigated. The absorption cross-section (σ_a) is 1.65 × 10⁻²⁰ cm² at 977 nm. The emission cross-section (σ_e) is 0.25 × 10⁻²⁰ cm² with an FWHM of 37.2 nm at 1020 nm. The fluorescence lifetime is 3.00 ms.     

Phase relations and hydrogenation behavior of Sr(Al1−xMgx)2

The phase relations and hydrogenation behavior of Sr(Al_1−xMg_x)₂ alloys were studied. The pseudobinary C36-type Laves phase Sr(Al,Mg)₂ was found as a structural intermediate between the Zintl phase and the C14 Laves phase. The single-phase regions for the Zintl phase, C36 phase and C14 phase, were determined to be x=0–0.10, 0.45–0.68 and 0.80–1, respectively. The Mg-substituted Zintl phase Sr(Al_0.95Mg_0.05)₂ can be hydrogenated to Sr(Al,Mg)₂H₂ at about 473 K. However, the Sr(Al,Mg)₂H₂ directly decomposes into SrH₂ and Sr(Al,Mg)₄ starting at 513 K. When the temperature is 573 K, the C36 Laves phase Sr(Al_0.5Mg_0.5)₂ can be hydrogenated into SrMgH₄ and Al, while the C14 Laves phase Sr(Al_0.1Mg_0.9)₂ is hydrogenated into SrMgH₄, Mg₁₇Al₁₂ and Mg.     

Structural and magnetic properties of Sm2Fe17−xCrxC2 nanocrystalline carbides with 0≤x≤2

The crystallographic and the Curie temperature of the Sm₂Fe_17−xCr_xC₂ (x=0.5, 1, 1.5 and 2) carbides have been extensively studied. X-ray diffraction studies have shown that all these alloys are approximately single phases corresponding to the Th₂Zn₁₇ type rhombohedral structure with a small amount of -Fe. The amount of this residual -Fe phase decreases with increasing the Cr atomic content. It decreases from 1 wt% for x=0.5 to 0.4 wt.% for x=2. The lattice parameter c increases as a function of the Cr atomic content x from x=0 to x=1.5 and then decreases. This is due to the Cr atoms which prefer to substitute the Fe atoms in the 6c sites located along the c-axis. The lattice parameter a and the unit-cell volume decrease in all substitution ranges. The insertion of the C atoms leads essentially to an increase of the distances between the 9d and 18h sites and the 9d–18f sites. The Curie temperature reaches a maximum value of 583 K for x=1.5 and then decreases to 551 K for x=2. The enhancement of the T_c for lower Cr contents is due to a lowering of the hybridization of the iron atoms with their neighbors, the magnetovolume effect and the reduction of antiferromagnetic interactions. However, the decrease in T_c for higher Cr content is due to the reduction in the number of Fe–Fe pairs due to the magnetic dilution effect. For given interatomic distances, the exchange coupling of the Cr–Cr atoms is not of antiferromagnetic type and the exchange integral of the Cr–Cr pair is higher than that of the Fe–Fe pair.     

Thermoelectric properties of novel skutterudites with didymium: DDy(Fe1−xCox)4Sb12 and DDy(Fe1−xNix)4Sb12

In order to improve the thermoelectric properties via efficient phonon scattering Didymium (DD), a mixture of Pr and Nd, was used as a new filler in ternary skutterudites (Fe_1−xCo_x)₄Sb₁₂ and (Fe_1−xNi_x)₄Sb₁₂. DD-filling levels have been determined from combined data of X-ray powder diffraction and electron microprobe analyses (EMPA). Thermoelectric properties have been characterized by measurements of electrical resistivity, thermopower and thermal conductivity in the temperature range from 4.3 to 800 K. The effect of nanostructuring in DD_0.4Fe₂Co₂Sb₁₂ was elucidated from a comparison of both micro-powder (ground in a WC-mortar, 10 μm) and nano-powder (ball-milled, 150 nm), both hot pressed under identical conditions. The figure of merit ZT depends on the Fe/Co and Ni/Co-contents, respectively, reaching ZT > 1. At low temperatures the nanostructured material exhibits a higher thermoelectric figure of merit. The Vickers hardness was measured for all samples being higher for the nanostructured material.     

Magnetic phase diagrams of the TbRh2−xPdxPdxSi2 and TbRu2−xPdxSi2 systems

The a.c. susceptibility and high field magnetization on TbRh_2−xPd_xPd_xSi₂ and TbRu_2−xPd_xSi₂ compounds were investigated up to 140 kOe. The (T,x) magnetic phase diagrams were determined. For both systems, an increase in the Pd content causes a decrease in the Néel temperature and changes the magnetization curves.     

Structure and magnetic properties of Gd3(Fe1−xTix)29 (x=0.011–0.034)

Single-phase compounds Gd₃(Fe_1−xTi_x)₂₉ (x=0.0110.034) have been synthesized. Gd₃(Fe_1−xTi_x)₂₉ crystallises in a monoclinic lattice with space group P2₁/c, and the crystal structure is refined by the Rietveld technique based on X-ray powder diffraction data. Thermomagnetic analysis indicates that the Curie temperature of the compounds ranges from 517 K to 538 K. The saturation magnetizations of the Gd₃(Fe_1−xTi_x)₂₉ (x=0.011, 0.022, 0.034) at 1.5 K are 103.6, 102.0 and 94.3 Am²/kg, and the anisotropy fields at 1.5 K are 6.0, 6.2 and 6.4T, respectively.     

Ba4In2−x(CO3)1+xO6−2.5x and Ba4In0.8Cu1.6(CO3)0.6O6.2—new indium oxycarbonates closely related to n=3 Ruddlesden–Popper phases

Investigations of phase relations in the Ba-rich part of the In₂O₃–BaO(CO₂)–CuO pseudo-ternary system at 900 °C have revealed the existence of new indium–copper oxycarbonate – Ba₄In_0.8Cu_1.6(CO₃)_0.6O_6.2. Rietveld refinement of the X-ray powder diffraction data combined with infrared studies gives evidence that this phase is a oxycarbonate crystallising in the tetragonal structure (space group I4/mmm) with unit cell parameters: a=4.0349(1) Å and c=29.8408(15) Å. In the binary part of the In₂O₃–BaO(CO₂) system we have identified the occurrence of Ba₄In_2−x(CO₃)_1+xO_6−2.5x oxycarbonate solid solution showing a crystal structure also described by I4/mmm space group, but with the unit cell parameters: a=4.1669(1) Å and c=29.3841(11) Å for x=1. The existence range of this phase, −0.153<x<0.4, includes chemical compositions of earlier found phases: Ba₅In_2+xO_8+0.5x with 0≤x≤0.45 (known as the -solid solution), as well as the binary Ba₄In₂O₇ phase. The crystal structures of both new oxycarbonates are isomorphic and related to n=3 member of the Ruddlesden–Popper family.     

Phase behavior and some properties of LaMn1−xRhxO3 solid solution

Structure and magnetic and electrical properties of the polycrystalline compounds LaMn_1−xRh_xO₃ (0 < x ≤ 1) have been investigated. The samples were characterized by X-ray diffraction and Rietveld refinement which confirmed the space group Pnma (No. 62) for all compositions at room temperature. A transformation from O′- to O-type orthorhombic structure is seen near x = 0.6 tending to make the phase unstable. The electrical conductivity measurement shows semiconducting property above room temperature with a rather low activation energy for Mn-rich compositions. Compounds in the region 0.1 ≤ x ≤ 0.9 show ferromagnetic property but the substitution of Rh³⁺ ion for Mn³⁺ ion suppresses the ferromagnetism that results in reducing the Curie temperature, T_C.     

Lattice parameter values and phase transitions for the Cu2Cd1−zMnzSnSe4 and Cu2Cd1−zFezSnSe4 alloys

X-ray powder diffraction measurements and differential thermal analysis (DTA) were made on polycrystalline samples of the Cu₂Cd_1−zMn_zSnSe₄ and Cu₂Cd_1−zFe_zSnSe₄ alloy systems. The diffraction patterns were used to show the equilibrium conditions and to derive lattice parameter values. For Cu₂Cd_0.8Fe_0.2SnSe₄ as well as for Cu₂Cd_0.2Fe_0.8SnSe₄ the crystal structures were refined using the Rietveld method. It was found that the internal distortion parameter σ decreases as Cd is replaced by either Mn and/or Fe. For the Cu₂Cd_1−zMn_zSnSe₄ and Cu₂Cd_1−zFe_zSnSe₄ alloy systems, only two single solid phase fields, the tetragonal stannite α and the wurtz–stannite δ (Pmn2₁) structures were found to occur in the diagram. In addition to the tetragonal stannite α phase extra X-ray diffraction lines due to MnSe and/or FeSe₂ were observed for as grown samples in the range 0.7 < z < 1.0. However, it was found that the amount of the extra phase decreased for the compressed samples.     

Structural, thermodynamic, and electrochemical properties of TixZr1−x(VNiCrMnCoAl)2 C14 Laves phase alloys

The crystal structure of the monoclinic phase η-Al₁₁Cr₂ of the space group C2/c, a ≈ 1.76 nm, b ≈ 3.05 nm, c ≈ 1.76 nm, β ≈ 90° [L.A. Bendersky, R.S. Roth, J.T. Ramon, D. Shechtman, Metall. Trans. A 22A (1991) 5] has been determined by single-crystal X-ray diffraction. The structure model, refined to a final R value of 0.0441, has the composition of Al_83.8Cr_16.2. a = 1.77348(10) nm, b = 3.04555(17) nm, c = 1.77344(10) nm, monoclinic angle β = 91.0520(12)°. There are 80 (66Al + 14Cr) independent atomic positions in a unit cell, of which all Cr atom sites and 8 Al atom sites have icosahedral coordination. These icosahedra are interconnected forming icosahedral chains along , (1 0 1) icosahedral layer blocks as well as a three-dimensional icosahedral structure.     

Magnetic properties of Pr1−xGdxMn2Ge2 compounds

The structure and magnetic properties of the Pr_1−xGd_xMn₂Ge₂ (0.0≤x≤1.0) compounds have been investigated by means of X-ray diffraction (XRD), differential scanning calorimetry (DSC) techniques and AC magnetic susceptibility measurements. All compounds crystallize in the ThCr₂Si₂-type structure with the space group I4/mmm. The lattice constants and the unit cell volume obey Vegard’s law. Samples in this alloy system exhibit a crossover from ferromagnetic ordering for PrMn₂Ge₂ to antiferromagnetic ordering for GdMn₂Ge₂ as a function of Gd concentration x. At low temperatures, the rare earth sublattice also orders and reconfigures the ordering in the Mn sublattice. The results are summarized in the x–T magnetic phase diagram.     

Investigation of the dependency of the upper critical magnetic field on the content x in Y1−xYbx/2Gdx/2Ba2Cu3O7−y superconducting structures

The Y_1−xYb_x/2Gd_x/2Ba₂Cu₃O_7−y superconducting samples for x = 0.0, 0.2, 0.4, 0.6, 0.8 and 1.0 were prepared by using the solid-state reaction technique. Resistivity measurements of the samples were performed in QD–PPMS system under different magnetic fields up to 5 T in zero fields cooling regime. Using the resistivity data, the upper critical magnetic field H_c2(0) at T = 0 K for 50% of R_n was calculated by the extrapolation H_c2(T) to the temperature T = 0 K. The coherence length in T = 0 K were calculated from H_c2(0) and the effects of x in the composition on both the coherence length and the upper critical magnetic field were examined. The results showed that H_c2(0) varied from 84.05 to 122.26 T with the content x. The upper critical magnetic field in the temperature T = 0 K slightly decreased with increasing the content x. Using the content x, the upper critical magnetic field can be controlled and this can be used in the superconductivity applications.     

Structural, electrical and magnetic properties of Cu1−xZnxFe2O4 ferrites (0 ≤ x ≤ 1)

Copper–zinc ferrites bearing chemical formula Cu_1−xZn_xFe₂O₄ for x ranging from 0.0 to 1.0 with the step increment of 0.2 were prepared by the standard solid-state technique. The variation of Zn substitution has a significant effect on the structural, electrical and magnetic properties. Lattice parameters ‘a’ increased from 8.370 to 8.520 Å. Dielectric constant decreased up to 311 with the increase in frequency from 80 Hz to 1 MHz at room temperature. All the samples follow the Maxwell–Wagner's interfacial polarization. Saturation magnetization, magnetic moment and Yafet–Kittel angles were also determined. The possible reasons responsible for the change in density related, electrical and magnetic properties with the increase in Zn concentration are undertaken.     

Structural and magnetic properties of single-crystalline spinel systems ZnCr2−xAlxSe4 (x = 0.15 and 0.23)

Single crystals of the spinel solid solutions ZnCr_2−xAl_xSe₄ with x = 0.15 and 0.23 were grown and studied by X-ray diffraction and macroscopic magnetic measurements. The solubility of Al³⁺ ions in the parent compound ZnCr₂Se₄ is very limited and only weakly substituted single crystals can be obtained. The spinel structure is hardly modified by this admixture and regular cation distribution is preserved. Alike ZnCr₂Se₄, the two compounds investigated order antiferromagnetically at low temperatures. Both the Néel temperatures and the paramagnetic Curie temperatures are similar to that reported for the parent selenide. Also the effective magnetic moments are close to that of ZnCr₂Se₄ and compatible with trivalent Cr ions. In contrast, the saturation magnetic moments measured above the metamagnetic phase transitions in strong magnetic fields and calculated per one Cr atom, appear to be strongly affected by the Al-substitution, being rapidly suppressed with rising Al-content.