SUPERHEATED STEAM IMPINGEMENT DRYING OF TORTILLA CHIPS

ABSTRACT

Low-fat snack products are the driving forces for the drying of tortilla chips before frying. Super-heated steam impingement drying of foods has the advantage of improved energy efficiency and product quality. The temperature profile, drying curves, and the physical properties (shrinkage, crispiness, starch gelatinization and microstructure) of tortilla chips dried at different superheated steam temperatures and heat transfer coefficients were measured. Results indicated that the steam temperature had a greater effect on the drying curve than the heat transfer coefficient within the range of study. The microstructure of the samples after steam drying showed that higher steam temperature resulted in more pores and coarser appearance. The modulus of deformation and the shrinkage of tortilla chips correlated with moisture content. A higher steam temperature caused less shrinkage and a higher modulus of deformation. The pasting properties showed that samples dried under a higher steam temperature and a higher heat transfer coefficient gelatinized less during drying and had a higher ability to absorb water. Comparison of the superheated steam drying and air drying revealed that at elevated temperatures the superheated steam provided higher drying rates. Furthermore, there was a less starch gelatinization associated with air drying compared to superheated steam drying.     

Comparative Evaluation of Hot-Air and Superheated-Steam Impinging Stream Drying as Novel Alternatives for Paddy Drying

An investigation was conducted on impinging stream drying of moist paddy using hot air and superheated steam as the drying media. Drying experiments were divided into two parts: namely, one-pass and two-pass drying. The volumetric water evaporation rate, volumetric heat transfer coefficient, and specific energy consumption of the drying system at various conditions were assessed; in the case of superheated-steam drying, the effect of steam recycle was also assessed. The quality of dried paddy was evaluated in terms of color, head rice yield, and degree of starch gelatinization. In the case of one-pass drying, an increase in the drying temperature led to a significant increase in the volumetric water evaporation rate and volumetric heat transfer coefficient. On the other hand, in the case of two-pass drying, an increase in the drying temperature led to a significant decrease in the volumetric heat transfer coefficient; the volumetric water evaporation rate was not significantly affected, however. The specific energy consumption decreased with an increase in the drying temperature. At the same temperature, using superheated steam as the drying medium led to lower specific energy consumption; higher level of steam recycle also led to more energy conservation. The color of the dried paddy was not affected by the change in the drying temperature; superheated-steam-dried paddy was redder and more yellow than the hot-air-dried paddy. An increase in the drying temperature led to decreased percentage of head rice yield. Superheated-steam drying helped enhance the level of starch gelatinization in comparison with hot-air drying at the same temperature. Nevertheless, drying at the highest tested temperature led to a lower level of starch gelatinization.     

Drying Kinetics and Quality of Shrimp Undergoing Different Two-Stage Drying Processes

An innovative two-stage drying concept is presented in this article. The work considered drying of shrimp using a superheated steam dryer followed by a heat pump (SSD/HPD) or a hot air dryer (SSD/AD) both from drying kinetics and dried product quality points of view. The experiments were performed using the first-stage superheated steam drying temperature of 140°C while the second-stage heat pump drying (or hot air drying) was performed at 50°C. The moisture content of shrimp at the end of the superheated steam drying stage was varied between 30 and 40% (w.b.). The effect of tempering between SSD/HPD was also investigated. Shrinkage, color, rehydration behavior, texture (toughness and hardness), and microstructure of dried shrimp were measured. The results showed that SSD/HPD dried shrimp had much lower degree of shrinkage, higher degree of rehydration, better color, less tough and softer, and more porous than single-stage SSD dried shrimp. It was also found that SSD/AD gave redder shrimp compared to shrimp dried in a single-stage superheated steam dryer. No improvement in terms of shrinkage and rehydration behavior was observed, however.     

DRYING OF SLICED RAW POTATOES IN SUPERHEATED STEAM AND HOT AIR

Drying experiments were conducted on raw potato slices, using atmospheric pressure superheated steam and hot air as drying media at 170 and 240°C. Mass changes of the material were continuously measured, the conditions of cross section near the surfaces were observed with an electron microscope, also color changes of their surface were measured during drying. The respective drying methods and temperature conditions were compared and it was found that, in the case of superheated steam drying, moisture content temporarily increases due to steam condensation in the initial stage of drying, therewith, as well as starch gelatinization rapidly develops. Meanwhile, in case of hot air drying, starch gelatinization occurs more slowly than with superheated steam drying and that non-gelatinized starch granules remain on the surface when drying was completed. Furthermore, surface color measurements showed that samples dried by superheated steam were more reddish than ones dried by hot air and the surfaces were more glossy, because no starch granules remain on the surface in case of superheated steam drying.     

DRYING OF SLICED RAW POTATOES IN SUPERHEATED STEAM AND HOT AIR

Drying experiments were conducted on raw potato slices, using atmospheric pressure superheated steam and hot air as drying media at 170 and 240°C. Mass changes of the material were continuously measured, the conditions of cross section near the surfaces were observed with an electron microscope, also color changes of their surface were measured during drying. The respective drying methods and temperature conditions were compared and it was found that, in the case of superheated steam drying, moisture content temporarily increases due to steam condensation in the initial stage of drying, therewith, as well as starch gelatinization rapidly develops. Meanwhile, in case of hot air drying, starch gelatinization occurs more slowly than with superheated steam drying and that non-gelatinized starch granules remain on the surface when drying was completed. Furthermore, surface color measurements showed that samples dried by superheated steam were more reddish than ones dried by hot air and the surfaces were more glossy, because no starch granules remain on the surface in case of superheated steam drying.     

Drying Kinetics and Quality of Shrimp Undergoing Different Two-Stage Drying Processes

Abstract

An innovative two-stage drying concept is presented in this article. The work considered drying of shrimp using a superheated steam dryer followed by a heat pump (SSD/HPD) or a hot air dryer (SSD/AD) both from drying kinetics and dried product quality points of view. The experiments were performed using the first-stage superheated steam drying temperature of 140°C while the second-stage heat pump drying (or hot air drying) was performed at 50°C. The moisture content of shrimp at the end of the superheated steam drying stage was varied between 30 and 40% (w.b.). The effect of tempering between SSD/HPD was also investigated. Shrinkage, color, rehydration behavior, texture (toughness and hardness), and microstructure of dried shrimp were measured. The results showed that SSD/HPD dried shrimp had much lower degree of shrinkage, higher degree of rehydration, better color, less tough and softer, and more porous than single-stage SSD dried shrimp. It was also found that SSD/AD gave redder shrimp compared to shrimp dried in a single-stage superheated steam dryer. No improvement in terms of shrinkage and rehydration behavior was observed, however.     

DESORPTION ISOTHERMS AND DRYING CHARACTERISTICS OF SHRIMP IN SUPERHEATED STEAM AND HOT AIR

Desorption isotherms for shrimp were determined at the temperatures of 50, 60, 70 and 80°C. Amongst the moisture equilibrium predictions between the BET and GAB models, the latter has a better predictable capability. The GAB parameters are correlated with the temperatures by the Arrhenius expression. Drying characteristics of shrimp in drying media at the temperature range of 120-180°C for superheated steam and of 70-140°C for hot air have been examined. Drying rate and effective diffusion coefficient are used to quantify quantitatively the difference between the superheated steam and the hot air dryings. The temperature is more important effect on drying rate and effective diffusion coefficient in the superheated steam than in the hot air. Inversion temperature exists between 140 and 150°C. Comparing to the hot air, the shrimp dried by the superheated steam shows a lower degree of shrimp shrinkage. In addition, product colours are slightly different to those from the commercial sources.     

Air-Impingement Drying of Tortilla Chips

Tortilla pieces were prepared from nixtamalized masa flour, and dried under impinging hot air. The effect of different drying conditions on the drying rate, texture, shrinkage profile and microstructure was analyzed. The results indicated that drying rate was mostly affected by the air temperature; texture was crispier at higher air temperatures: shrinkage of the piece was higher at lower convective heat transfer coeffieient; and microstructure looked smoother at higher air temperature.     

Drying Foodstuffs with Superheated Steam

A thin-layer superheated steam drier was constructed with the objective of determining the drying characteristics, drying rates, and the effect of superheated steam on product quality in thin-layers. Results from superheated steam drying experiments with sugar-beet pulp, potatoes, Asian noodles, and spent grains indicate that drying times and rates increase with increasing steam temperature. For sugar-beet pulp it was also found that these changes were more significant than increases seen by hot-air drying under the same conditions and that drying rates were not affected by velocity for hot air but were increased for superheated steam. When quality aspects were examined, superheated steam dried Asian noodles saw both beneficial changes to recovery, adhesiveness, and gumminess while parameters of maximum cutting stress, resistance to compression, and surface firmness saw deleterious effects. Spent grains saw high levels of starch gelatinization and retention of fibre content.     

Air-Impingement Drying of Tortilla Chips

ABSTRACT

Tortilla pieces were prepared from nixtamalized masa flour, and dried under impinging hot air. The effect of different drying conditions on the drying rate, texture, shrinkage profile and microstructure was analyzed. The results indicated that drying rate was mostly affected by the air temperature; texture was crispier at higher air temperatures: shrinkage of the piece was higher at lower convective heat transfer coeffieient; and microstructure looked smoother at higher air temperature.     

Drying Foodstuffs with Superheated Steam

Abstract

A thin-layer superheated steam drier was constructed with the objective of determining the drying characteristics, drying rates, and the effect of superheated steam on product quality in thin-layers. Results from superheated steam drying experiments with sugar-beet pulp, potatoes, Asian noodles, and spent grains indicate that drying times and rates increase with increasing steam temperature. For sugar-beet pulp it was also found that these changes were more significant than increases seen by hot-air drying under the same conditions and that drying rates were not affected by velocity for hot air but were increased for superheated steam. When quality aspects were examined, superheated steam dried Asian noodles saw both beneficial changes to recovery, adhesiveness, and gumminess while parameters of maximum cutting stress, resistance to compression, and surface firmness saw deleterious effects. Spent grains saw high levels of starch gelatinization and retention of fibre content.

     

Some Considerations In Simulation Of Superheated Steam Drying Of Softwood Lumber

ABSTRACT

A mathematical model for high-temperature drying of softwood lumber with moist air has been modified and extended to simulate wood drying with superheated steam. In the simulation, differences between the two types of drying are considered, these include: external heat and mass transfer processes and calculation of equilibrium moisture content. The external mass transfer coefficient in the perheated steam drying was found to be much higher than that in the moist air drying, however, the heat ransfer coefficients for these two cases were of the same order. The predicted drying curves and wood temperatures from the superheated steam drying model were compared with experimental data and there was close agreement. Further studies will apply the model to development of commercial drying schedules for wood drying with superheated steam.     

DRYING RATE AND TEMPERATURE PROFILE FOR SUPERHEATED STEAM VACUUM DRYING AND MOIST AIR DRYING OF SOFTWOOD LUMBER

Two charges of green radiata pine sapwood lumber were dried, either using superheated steam under vacuum (90°C, 0.2 bar abs.) or conventionally using hot moist air (90/60°C). Due to low density of the drying medium under vacuum, the circulation velocity used was 10 m/s for superheated steam drying and 5.0 m/s for moist air drying, and in both cases, the flow was unidirectional. In drying, stack drying rate and wood temperatures were measured to examine the differences between the superheated steam drying and drying using hot moist air.

The experimental results have shown that the stack edge board in superheated steam drying dried faster than in the hot moist air drying. Once again due to the low density of the steam under vacuum, a prolonged maximum temperature drop across load (TDAL) was observed in the superheated steam drying, however, the whole stack dried slower and the final moisture content distribution was more variable than for conventional hot moist air drying. Wood temperatures in superheated steam drying were lower.     

DRYING RATE AND TEMPERATURE PROFILE FOR SUPERHEATED STEAM VACUUM DRYING AND MOIST AIR DRYING OF SOFTWOOD LUMBER

Abstract

Two charges of green radiata pine sapwood lumber were dried, either using superheated steam under vacuum (90°C, 0.2 bar abs.) or conventionally using hot moist air (90/60°C). Due to low density of the drying medium under vacuum, the circulation velocity used was 10 m/s for superheated steam drying and 5.0 m/s for moist air drying, and in both cases, the flow was unidirectional. In drying, stack drying rate and wood temperatures were measured to examine the differences between the superheated steam drying and drying using hot moist air.

The experimental results have shown that the stack edge board in superheated steam drying dried faster than in the hot moist air drying. Once again due to the low density of the steam under vacuum, a prolonged maximum temperature drop across load (TDAL) was observed in the superheated steam drying, however, the whole stack dried slower and the final moisture content distribution was more variable than for conventional hot moist air drying. Wood temperatures in superheated steam drying were lower.     

Quality Changes of Superheated Steam–Dried Fibers from Oil Palm Empty Fruit Bunches

Conventional drying of the fibers from oil palm empty fruit bunches (EFB) using flue gas from diesel burners frequently causes browning and dust explosion. Replacing the drying medium with superheated steam is expected to improve the quality of EFB fibers as well as improve the safety of the dryer operation. In this study, the effects of steam temperature and steam velocity on the quality of steam–dried EFB fibers was investigated. The drying experiment was carried out at atmospheric pressure with steam superficial velocity in the range of 0.3 to 0.49 m s^?1 and temperature in the range of 135 to 200°C. Three quality parameters of the EFB fibers, the color, strength, and microstructure, were used to assess the changes in EFB fiber quality as a result of superheated steam drying. The color of the EFB fiber was either improved or not significantly degraded. The strength of the superheated steam–dried EFB fibers was higher than that of undried and hot air–dried EFB fibers. The microstructure of fresh undried EFB fibers as seen by scanning electron microscopy (SEM) showed the presence of round silica particles of 10–20 µm in diameter all over the EFB fiber strand, which complicates pulping and bleaching. Superheated steam drying successfully removed the silica particles from the EFB fibers at temperatures of at least 200°C and a velocity of steam of at most 0.49 m s^?1, which is better than hammering, which can only remove 88% of the silica particles. The high temperature of the superheated steam loosened the silica particles from their craters. The EFB fibers cracked and split at steam velocities at or above 0.49 m s^?1 and high superheated steam temperatures at or above 200°C and as a consequence became weaker at these conditions. The removal of silica particles by superheated steam drying makes the EFB fiber amenable to pulping and bleaching. Superheated steam drying is therefore found to improve the overall quality of EFB fibers compared to hot air drying.     

Study of Intermittent Low-Pressure Superheated Steam and Vacuum Drying of a Heat-Sensitive Material

Low-pressure superheated steam drying (LPSSD) has recently been applied to drying of various heat-sensitive foods and bioproducts with success. Several studies have shown that the quality of LPSSD-dried products is superior to that obtained using conventional hot air or vacuum drying. However, drying time and energy consumption for LPSSD is generally greater than that for vacuum drying. Therefore, it is necessary to examine different methodologies to improve the energy efficiency of LPSSD. An intermittent drying scheme is one possible method to reduce the energy consumption of the process while maintaining the desired product quality. In this study, the effect of intermittent supply of energy (through an electric heater and steam injection to the dryer) and vacuum (through the use of a vacuum pump) at various intermittency values or on:off periods (10:5, 10:10 and 10:20 min in the case of intermittent supply of energy and 5:0, 5:5, and 5:10 min in the case of intermittent supply of vacuum) at the on-period setting temperatures of 70, 80, and 90°C on the drying kinetics and heat transfer behavior of the drying samples (banana chips) was studied. The effects of these intermittent drying schemes and conditions on the quality parameters of dried banana chips; i.e., color, shrinkage, texture, and ascorbic acid retention, were also studied. Finally, the energy consumption values for intermittent LPSSD and vacuum drying were monitored through the effective (or net) drying time at various intermittent drying conditions and compared with those using continuous LPSSD and vacuum drying.     

Controllability of Product Moisture Content When Nonscreened Sawdust Is Dried in a Spouted Bed

The control of the dried product's moisture content is of importance in the production of fuel pellets. Tests have been made in air and superheated steam in a spouted bed using the outlet temperature of the drying medium as a control parameter of the dried material's moisture content. For superheated steam different settings for the inlet medium temperature are also used. In the moisture content interval of 8-17% wet base there is a linear correlation between the dried material moisture content and the outlet temperature of the drying medium. When drying nonscreened sawdust in a spouted bed it is recommendable to use the outlet temperature of the drying medium as a control parameter of the dried material moisture content. This is independent of the size of the sawdust, whether superheated steam or air is used as a drying medium.     

A Comparative Study of Pork Drying Using Superheated Steam and Hot Air

Drying with superheated steam and hot air were comparatively studied for pork. Transport, physical, and chemical properties, i.e., effective diffusivity, color, microstructure, and rehydration ability, were investigated. The experimental results have shown that the decrease of pork moisture content in an early drying time was more rapid in superheated steam than in hot air and appeared to be lower in a latter time. The pork surface as examined by SEM was noticeably different for the samples dried by superheated steam and hot air. The fewer pores at the surface of superheated steam-dried pork caused a slower water penetration into the interior during rehydration, in addition to the lower drying rate. The color of the product from superheated steam was a relatively more intense brown than that obtained from hot air as presented by a lower L? value and a higher a? value.     

A Comparative Study of Pork Drying Using Superheated Steam and Hot Air

Drying with superheated steam and hot air were comparatively studied for pork. Transport, physical, and chemical properties, i.e., effective diffusivity, color, microstructure, and rehydration ability, were investigated. The experimental results have shown that the decrease of pork moisture content in an early drying time was more rapid in superheated steam than in hot air and appeared to be lower in a latter time. The pork surface as examined by SEM was noticeably different for the samples dried by superheated steam and hot air. The fewer pores at the surface of superheated steam-dried pork caused a slower water penetration into the interior during rehydration, in addition to the lower drying rate. The color of the product from superheated steam was a relatively more intense brown than that obtained from hot air as presented by a lower L* value and a higher a* value.     

Experimental Investigation and Practical Application of Superheated Steam Drying Technology for Softwood Timber

Due to several advantages, superheated steam drying of timber has attracted great attention. However, the technology is still restricted to some special cases, partly due to the lack of fully understanding of the drying process. In this work, experiments were conducted to dry radiata pine timber using superheated steam under vacuum and at pressure. In the first part of the experiments, softwood timber was dried in a superheated steam kiln with drying rates, steam temperature across the stack and wood temperature being measured during drying. In the second part of the work, experimental studies were performed to investigate potential applications of the superheated steam drying at ultra-high temperatures (UHT) and pressurized steam conditioning of kiln dried timber. Compared to normal drying temperatures, the UHT drying can reduce the drying time by a factor of 5 to 10 and it is also more energy efficient. The pressurized steam conditioning has been proven to be a promising technology to relieve drying stresses and to reduce twist of the dried timer.