Efficient electrochemical reduction of nitrate to nitrogen on tin cathode at very high cathodic potentials

The electrochemical reduction of nitrate on tin cathode at very high cathodic potentials was studied in 0.1 M K₂SO₄, 0.05 M KNO₃ electrolyte. A high rate of nitrate reduction (0.206 mmol min⁻¹ cm⁻²) and a high selectivity (%S) of nitrogen (92%) was obtained at −2.9 V versus Ag/AgCl. The main by-products were ammonia (8%) and nitrite (<0.02%). Small amounts of N₂O and traces of NO were also detected.As the cathodic potential increases, the %S of nitrogen increases, while that of ammonia displays a maximum at −2.2 V. The %S of nitrite decreases from 65% at −1.8 V to <0.02% at −2.4 V. The kinetic analysis indicated that the formation of nitrogen and ammonia proceeds through the intermediate nitrite.The reduction follows first order kinetics for both nitrate and nitrite at more cathodic potentials than −2.4 V, while at less negative potentials the kinetics is more complicated.The %Faradaic efficiency (%FE) of the reduction at −2.9 V was about 60% initially and decreased to 22% at 40 min.A cathodic corrosion of tin was observed, which was more intensive in the absence of nitrate. At potentials more negative than −2.4 V, small amounts of tin hydride were detected.     

Influence of nitrate concentration on its electrochemical reduction on tin cathode: Identification of reaction intermediates

The influence of the concentration of nitrate in the range between 100 and 62,000 mg L⁻¹ NaNO₃ in NaCl solutions was studied under constant potential electrolysis at −2.8 V vs. Ag/AgCl. The rate of the reduction follows Langmuir-Hinshelwood kinetics, according to which zero order kinetics is followed at concentrations higher than 0.3 M whereas first order at lower concentrations.The selectivity to nitrogen increases from 70 to 83% as the concentration of nitrate increases from 100 to 1500 mg L⁻¹ and it remains almost constant for higher nitrate concentrations, whereas that of ammonia exhibits the opposite trend decreasing from 25 to 11%. The % Faradaic Efficiency (%FE) increased with the increase of the concentration of nitrate from 25% at 0.1 M to 78% at 1 M when 95% of nitrate was reduced in both cases. At high concentrations of nitrate, hyponitrite and hydroxylamine were detected as intermediates of the reduction and a reaction scheme which is in agreement with the experimental results has been proposed.The hydrogen evolution in our conditions probably takes place through the discharge of the cation of the supporting electrolyte instead of the Volmer-Tafel mechanism and the reduction of nitrate proceeds through electrochemical hydrogenation.     

Effect of hydroxyl ions on chloride penetration depth measurement using the colorimetric method

In this paper, the effect of hydroxyl ions on chloride penetration depth measurement using the colorimetric method was studied. Equivalent silver nitrate solution (i.e. Ag⁺ = Cl⁻) was added to the NaCl + NaOH solution with different concentrations, then the amount of precipitated silver chloride and silver oxide were determined by chemical methods, and the color of the precipitated products was examined. Results show that the amount of silver chloride formed decreases linearly as OH⁻ to Cl⁻ ratio (r) increases. Thus, the chloride concentration at color change boundary changes with the pH value of the concrete. AgCl has a white color, while Ag₂O has a dark brown color. When the value of r exceeds 4, the color of the mixture looks brown, and color change boundary cannot be easily distinguished.     

Electrochemical activity of Geobacter sulfurreducens biofilms on stainless steel anodes

Stainless steel was studied as anode for the biocatalysis of acetate oxidation by biofilms of Geobacter sulfurreducens. Electrodes were individually polarized at different potential in the range −0.20 V to +0.20 V vs. Ag/AgCl either in the same reactor or in different reactors containing acetate as electron donor and no electron acceptor except the working electrode. At +0.20 V vs. Ag/AgCl, the current increased after a 2-day lag period up to maximum current densities around 0.7 A m⁻² and 2.4 A m⁻² with 5 mM and 10 mM acetate, respectively. No current was obtained during chronoamperometry (CA) at potential values lower than 0.00 V vs. Ag/AgCl, while the cyclic voltammetries (CV) that were performed periodically always detected a fast electron transfer, with the oxidation starting around −0.25 V vs. Ag/AgCl. Epifluorescent microscopy showed that the current recorded by chronoamperometry was linked to the biofilm growth on the electrode surface, while CVs were more likely linked to the cells initially adsorbed from the inoculum. A model was proposed to explain the electrochemical behaviour of the biofilm, which appeared to be controlled by the pioneering adherent cells playing the role of “electrochemical gate” between the biofilm and the electrode surface.     

Electrochemical study of calcium carbonate deposition on iron. Effect of the anion

Deposition of calcium carbonate on iron from supersaturated solutions containing 1 M sodium chloride, bromide, iodide, or nitrate as supporting electrolyte was studied at 60 °C under open-circuit conditions using impedance spectroscopy, chronopotentiometry, voltammetry, and scanning electron microscopy. The anions were found to fall into two groups with respect to their effect on scaling. On the one hand, chloride and, especially, nitrate favor faster scaling kinetics and lead to compact carbonate films composed of entangled aragonite crystals. On the other hand, in the presence of bromide and iodide the scaling rate is lower and the resulting films feature aragonite crystals more or less freely scattered on what appears to be a uniform sublayer of unknown structure. The experimental data are adequately described using quasi-uniform film model accounting for the cathodic and anodic electrode reactions. As deduced from the electrochemical measurements, the barrier properties of the carbonate films formed in different supporting electrolytes increase in the order of Cl⁻ < NO₃⁻ ≈ Br⁻ < I⁻.     

Strategy for the syntheses of isolated fine silver nanoparticles and polypyrrole/silver nanocomposites on gold substrates

In this work, isolated fine silver nanoparticles and polypyrrole/silver nanocomposites with diameters of about 10 nm on gold substrates were first prepared by electrochemical methods. First, an Ag substrate was cycled in a deoxygenated aqueous solution containing 0.1 M HCl from −0.30 to +0.30 V versus Ag/AgCl at 5 mV/s with 30 scans. Subsequently the Ag working electrode was immediately replaced by an Au electrode and a cathodic overpotential of 0.2 V was applied under controlled sonication to synthesize Ag nanoparticles on the Au electrode. Then pyrrole monomers were encouragingly found to be polymerized on the deposited Ag nanoparticles. This polymerization is distinguishable from the known chemical or electrochemical one, due to the electrochemical activity of unreduced species of Ag_n⁺ clusters inside the nanoparticles. Also, this polymerization may be ascribed to the oxidizing agent of AuCl₄⁻, which is present on the Au electrode.     

Aluminum assisted electrodeposition of europium in LiCl-KCl molten salt

Cyclic voltammetry (CV), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) were employed to investigate the electrodeposition of Eu and Al in an LiCl-KCl eutectic melt containing Eu²⁺ and Al³⁺ at 450 °C. In order to deposit a pure Eu and Al alloy, the stoichiometrically lower concentration of Al³⁺ than that of Eu²⁺ and Al wires as a counter electrode was introduced into the bath of LiCl-KCl melt for the electrodeposition. The electrodeposition takes place at a potential more negative than −1.95 V vs. Ag|Ag⁺ while the deposit is oxidized at more positive potential than −1.92 V. Two new reduction peaks and an anodic peak on a W working electrode were observed at −2.39 V, −2.42 V, and −2.1 V, vs. Ag|Ag⁺, respectively, suggesting that the potential window of the Al system in LiCl-KCl melt can be extended to −2.43 V vs. Ag|Ag⁺. The EDS analysis indicated that AlEu can be deposited at the potential more negative than −2.37 V.     

Electrochemical modification of glassy carbon electrode by poly-4-nitroaniline and its application for determination of copper(II)

Electrochemical modification of glassy carbon (GC) electrode by poly-4-nitroaniline (P4NA), electrochemical reduction of P4NA and applicability of electrode modified in this way for determination of copper(II) (Cu(II)) is reported in this study. Electrochemical surface modification was performed by cyclic voltammetry in the potential range between +0.9 V and +1.4 V vs. Ag/Ag⁺ (in 10 mM AgNO₃) at the scan rate of 100 mV/s by 100 cycles in non-aqueous media. In order to provide electrochemical reduction of nitro groups on the P4NA-modified GC electrode surface (P4NA/GC), the cyclic voltammograms inducing/evidencing the reduction of nitro groups were performed in the potential range between −0.1 V and −0.8 V vs. Ag/AgCl/(sat.KCl) at the scan rate of 100 mV/s. The reduced P4NA/GC surfaces (Reduced-P4NA/GC) were treated with aqueous solution of nitrilotriacetic acid. The sensitivity of GC electrode modified in described way towards Cu(II) was investigated in Britton-Robinson buffer solution, pH 5.0. The potentiometric generic pulse technique was applied as innovative electrochemical method for detection of analytical signal. It was shown that GC electrodes modified in here described way will be suitable for the determination of Cu(II) in technological waste water and/or some other solutions containing Cu(II) ions.     

Cathodic electrochemiluminescence of luminol in aqueous solutions based on C-doped oxide covered titanium electrode

In the present work, a novel sensor for luminol electrochemiluminescence (ECL) was constructed on the base of a C-doped titanium oxide amorphous semiconductor electrode. The morphology, structural and electrochemical properties of the electrode was characterized by X-Ray diffraction, X-Ray photoelectron spectroscopy and electrochemical methods. The ECL behavior of luminol excited by hot electrons injected from C-doped oxide film-covered electrodes in aqueous medium has been investigated in B-R buffer solution (pH = 9) when linear sweep cyclic voltammetry (CV) was applied. Two ECL peaks were observed at −1.0 V (vs. Ag/AgCl, reduction process) and −0.75 V (vs. Ag/AgCl, oxidation process). The possible mechanism was discussed. The C-doped Ti oxide electrode shows excellent properties for sensitive determination of luminol with good reproducibility and stability. The linear response of luminol was in the range of 1 × 10⁻⁸ to 9 × 10⁻⁸ mol/L with the detection limit of 3 × 10⁻⁹ mol/L (S/N = 3). Since luminol is one of the most useful ECL probe, many bioactive compounds which can be labeled by luminol are able to be detected by using the proposed method.     

Microbial electrocatalysis with Geobacter sulfurreducens biofilm on stainless steel cathodes

Stainless steel and graphite electrodes were individually addressed and polarized at −0.60 V vs. Ag/AgCl in reactors filled with a growth medium that contained 25 mM fumarate as the electron acceptor and no electron donor, in order to force the microbial cells to use the electrode as electron source. When the reactor was inoculated with Geobacter sulfurreducens, the current increased and stabilized at average values around 0.75 A m⁻² for graphite and 20.5 A m⁻² for stainless steel. Cyclic voltammetry performed at the end of the experiment indicated that the reduction started at around −0.30 V vs. Ag/AgCl on stainless steel. Removing the biofilm formed on the electrode surface made the current totally disappear, confirming that the G.sulfurreducens biofilm was fully responsible for the electrocatalysis of fumarate reduction. Similar current densities were recorded when the electrodes were polarized after being kept in open circuit for several days. The reasons for the bacteria presence and survival on non-connected stainless steel coupons were discussed. Chronoamperometry experiments performed at different potential values suggested that the biofilm-driven catalysis was controlled by electrochemical kinetics. The high current density obtained, quite close to the redox potential of the fumarate/succinate couple, presents stainless steel as a remarkable material to support biocathodes.     

Kinetic study of nitrate reduction on Pt(1 1 0) electrode in perchloric acid solution

The kinetics of electrocatalytic reduction of nitrate on Pt(1 1 0) in perchloric acid was studied with cyclic voltammetry at a very low sweep rate of 1 mV s⁻¹, where pseudo-steady state condition was assumed to be achieved at each electrode potential. Stationary current-potential curves in perchloric acid in the absence of nitrate showed two peaks at 0.13 V and 0.23 V (RHE) in the so-called adsorbed hydrogen region. The nitrate reduction proceeded in the potential region of the latter peak in the pH range studied. The reaction orders with respect to NO₃⁻ and H⁺ were observed to be close to 0 and 1, respectively. The former value means that the adsorbed NO₃⁻ at a saturated coverage is one of the reactants in the rate-determining step (rds). The latter value means that hydrogen species is also a reactant above or on the rds. The Tafel slope of nitrate reduction was −66 mV per decade, which is taken to be approximately −59 mV per decade, indicating that the rds is a pure chemical reaction following electron transfer. We discuss two possible reaction schemes including bimolecular and monomolecular reactions in the rds to explain the kinetics and suggest that the reactants in the rds are adsorbed hydrogen and adsorbed NO₃⁻ with the assistance of the results in our recent report for nitrate reduction on Pt(S)[n(1 1 1) × (1 1 1)] electrodes: the nitrate reduction mechanism can be classified within the framework of the Langmuir-Hinshelwood mechanism.     

Synergic effect of benzotriazole and chloride ion on Cu passivation in a phosphate electrochemical mechanical planarization electrolyte

In this study, the effect of chloride ion (Cl⁻) in phosphate electrolytes of pH 2 containing benzotriazole (BTAH) developed for use in electrochemical mechanical planarization (ECMP) was investigated at various anodic potentials. According to D.C. and A.C. electrochemical analyses, the inhibition effect of the BTAH passive film formed in phosphate electrolyte containing both BTAH and Cl⁻ was superior to that formed in phosphate electrolytes containing BTAH alone, even at high anodic potential. The effective window for BTAH passivation reached ∼1.3 V vs. Ag/AgCl nearly three times that of the ∼0.5 V vs. Ag/AgCl recorded for electrolyte containing BTAH alone. According to analyses conducted by atomic force microscopy (AFM) and secondary ion mass spectrometer (SIMS), the thickness of the passive film grown from the BTAH-only electrolyte at 0.3 V vs. Ag/AgCl was ∼52 ± 7 nm and ∼55 nm, respectively. As for the passive film grown from the BTAH and Cl⁻ electrolyte, the thickness increased to ∼104 ± 18 nm and ∼106 nm, respectively. The mechanism for the enhanced inhibition capability was that the passive film grown from the BTAH and Cl⁻ electrolyte was thicker compared to that formed from the BTAH-only electrolyte due to the incorporation of Cl⁻ into the BTAH passive film. The ECMP polishing results also demonstrated an obvious step height reduction of ∼1000 nm in a patterned structure for only 60 s polishing at a high potential of 1.0 V vs. Ag/AgCl under a low downward pressure (∼0.5 psi). Subsequently, this study proposes that the control of Cl⁻ in a phosphate ECMP electrolyte of pH 2 may be useful in enhancing the passivation capability of BTAH passive film, thus expanding the operating potential window.     

Role of surface state on the electron flow in modified TiO2 film incorporating carbon powder for a dye-sensitized solar cell

An investigation of surface-related traps in nanostructured TiO₂ films modified by the incorporation of carbon powder was conducted by the potential-step chronoamperometric method. For the modification of the morphology and surface state of the nanoporous TiO₂ electrode, the incorporation of carbon into the white TiO₂ powder was accomplished. In the chronoamperometric data, all of the transients showed an initial fast phase (<1 s) followed by a slower phase which is related to the trap filling process. The trap-filling period of the carbon incorporated TiO₂ film becomes longer, as the applied negative potential increases, due to the widely distributed traps induced by the increased surface area. Furthermore, the film capacitance was derived as a function of the applied bias by integrating the current to time curves of the chronoamperometric data. The accumulated charge of the carbon incorporated TiO₂ film increases prominently in two regions. The dominant increase shown in the positive region (−0.7 to −0.9 V vs. Ag/AgCl at pH 13) of the flat band potential implies that the electron occupancy in the surface-related traps is increased. At a more negative potential (below −1.2 V vs. Ag/AgCl), electrons from the conduction band of the TiO₂ film substantially influence the total current, thereby inducing an exponential increase in the current. Therefore, it is found that most of the traps are located in the positive region of the flat band potential, since the Fermi level of the nanostructured TiO₂ film is positioned at −1.14 V vs. Ag/AgCl at pH 13. The trap sites in the sub-bandgap region of the TiO₂ film are important in the electron transport of photoinjected electrons from dye molecules and partially charge recombination with redox electrolyte in operating dye-sensitized solar cell. The influence of charge trap formed by increased surface states on the electron transport and electron transfer was investigated by photovoltage and photocurrent transient measurements.     

Electrocatalytic reduction of nitrate on copper electrode in alkaline solution

This work is devoted to the study of the kinetics and reaction mechanism of nitrate reduction on a copper electrode in 0.1 M NaOH, which acts as the supporting electrolyte. The experimental methods include cyclic voltammetry (CV), cronoamperometry (CA), controlled-potential electrolysis (CPE), and coulometry. In CV, there are three potential regions where charge transfer reactions take place, reactions which are associated with NO₃⁻ and/or intermediates reduction. Two isopotential points observed in CV indicate the existence of some competitive adsorption processes at the electrode surface.The three charge transfer steps were also made evident in the CA, CPE and coulometry studies. The correlation of the experimental results with the literature data led to the conclusion that NO₃⁻ reduction on a copper electrode in 0.1 M NaOH has an intermediate (N₂O₂²⁻) species, which reduces to N₂ at a potential of about −1.3 V and to NH₄OH at potential values lower than −1.4 V (both values are vs. SCE).     

Electrochemical behavior of p-tert-butyl calix[8]arene in CH2Cl2

The electrochemical behavior of p-tert-butyl calix[8]arene has been investigated by cyclic voltammetry. The result shows that there is an irreversible electrochemical oxidative wave when the potential ranges from −0.3 to 1.6 V versus Ag/0.1 M AgNO₃ in acetonitrile (Ag/Ag⁺). At 25 °C, the peak potential is ca. 1.43 V (versus Ag/Ag⁺) at scan rate of 0.05 V s⁻¹. The number of the electrons transferred in the electrochemical reaction is four. The diffusion coefficient of p-tert-butyl calix[8]arene is 2.8 × 10⁻⁵ cm² s⁻¹. The diffusion activation energy is 12.3 kJ mol⁻¹.     

Kinetics of trichloroethene dechlorination and methane formation by a mixed anaerobic culture in a bio-electrochemical system

In the present study, we investigated the use of a lab-scale, bio-electrochemical system to generate H₂ from protons reduction at controlled cathodic potentials, in support of the microbial reductive dechlorination of trichloroethene (TCE). Several batch potentiostatic experiments were performed on graphite cathodes at different potentials ranging from −0.700 to −1.000 V vs. Ag/AgCl. By appropriately changing the applied cathode potential it was possible to finely control the liquid phase H₂ concentration, which resulted from a balance between H₂ generation (from protons reduction) and consumption (from dechlorination and methanogenesis). Microbial TCE dechlorination was stimulated when the potential applied to the graphite cathode was lower than −0.800 V vs. Ag/AgCl. However, a combination of high dechlorination rate and high current efficiency was achieved only in a very narrow range of cathode potentials (i.e., −0.850 to −0.875 V vs. Ag/AgCl). Methane formation was significantly slower than TCE dechlorination, probably due to the presence in the mixed culture of a lower number of methanogens compared to dechlorinators. In spite of this fact, these two competing metabolisms were stimulated in a similar way by the application of an external potential, thereby indicating a similar affinity for H₂. Indeed, calculated half-velocity coefficients for H₂ for dechlorination and methanogenesis were 20.1 ± 7.6 and 17.9 ± 8.5 nM, respectively.     

An enzyme-based microfluidic biofuel cell using vitamin K3-mediated glucose oxidation

Viamin K₃-modified poly-l-lysine (PLL-VK₃) was synthesized and used as the electron transfer mediator during catalytic oxidation of NADH by diaphorase (Dp) at the anode of biofuel cell. PLL-VK₃ and Dp were co-immobilized on an electrode and then coated with NAD⁺-dependent glucose dehydrogenase (GDH). The resulting enzymatic bilayer (abbreviated PLL-VK₃/Dp/GDH) catalyzed glucose oxidation. Addition of carbon black (Ketjenblack, KB) into the bilayer enlarged the effective surface area of the electrode and consequentially increased the catalytic activity. An oxidation current of ca. 2 mA cm⁻² was observed when the electrochemical cell contained a stirred 30 mM glucose, 1.0 mM NAD⁺, pH 7.0 phosphate-buffered electrolyte solution. The performance of glucose/O₂ biofuel cells, constructed as fluidic chips with controllable fuel flow and containing a KB/PLL-VK₃/Dp/GDH-coated anode and an Ag/AgCl or a polydimethylsiloxane-coated Pt cathode, were evaluated. The open circuit voltage of the cell with the PDMS-coated Pt cathode was 0.55 V and its maximum power density was 32 μW cm⁻² at 0.29 V when a pH 7.0-buffered fuel containing 5.0 mM glucose and 1.0 mM NAD⁺ was introduced into the cell at a flow rate of 1.0 mL min⁻¹. The cell's output increased as the flow rate increased. During 18 h of continuous operation of the cell with a load of 100 kΩ, the output current density declined by ca. 50%, probably due to swelling of the enzyme bilayer.     

Oxygen and hydrogen peroxide reduction catalyses in neutral aqueous media using copper ion loaded glassy carbon electrode electrolyzed in ammonium carbamate solution

An aminated glassy carbon electrode (AGCE) can be obtained by the electrode oxidation of glassy carbon electrode in ammonium carbamate solution. In the cyclic voltammetric experiments, the electrode reduction of the dissolved oxygen began from −0.15 V vs. Ag/AgCl in neutral aqueous media when the aminated glassy carbon electrode was used as a working electrode although it began from −0.40 V vs. Ag/AgCl when a polished GCE was used. The nitrogen containing groups introduced by the electrode oxidation of carbamic acid must be related with the acceleration of the electron transfer rate of oxygen. Moreover, the new reduction wave of the dissolved oxygen appeared at +0.15 V vs. Ag/AgCl when copper (II) ion was coordinated to AGCE surface. This reduction potential of oxygen coincided with that of copper (II) ion and this fact suggests that the coordinated copper ion to the aminated carbon surface works as a redox mediator of oxygen. The reduction product of oxygen was monitored by rotating platinum ring - aminated glassy carbon disk electrode, and it was found that most of oxygen was reduced to water in a potential range negative than −0.4 V vs. Ag/AgCl. By using AGCE, it was recognized that the catalytic reduction of hydrogen peroxide was also taken place as well as oxygen reduction.     

Poly-o-phenylenediamine as redox mediator for laccase

Electrocatalytic activity towards oxygen reduction of fungal laccase entrapped in poly-o-phenylenediamine (POPDA) matrix on glassy carbon electrodes was studied. Cyclic voltammetry and amperometric responses to dissolved oxygen were investigated in pH range from 2 to 6. POPDA reveals a unique ability to serve as a redox mediator for laccase and immobilizing matrix at the same time. The entrapped enzyme efficiently catalyzes reduction of molecular oxygen without any additional mediators. The electrocatalytic current reaches 0.1 mA/cm⁻² per 1 μg of immobilized enzyme on cyclic voltammograms recorded at 1 mV/s in a not stirred electrolyte. Current density values are comparable with those revealed by dissolved laccase (60 μg/ml) mediated by hydroquinone and greatly higher than by the mediator less laccase/glassy carbon system. The potential of oxygen reduction is determined by the polymer redox couple. Consequently, the onset of the oxygen reduction shifts from −0.15 V versus Ag/AgCl in pH 6 to +0.05 V versus Ag/AgCl in pH 2. The laccase-POPDA layers immersed in the deaerated solution show fast amperometric responses to addition of the oxygen containing solution. The observed current values depend linearly on the oxygen concentration. Factors affecting the electrocatalytic activity of the laccase-POPDA system, including the layer thickness and the pH value, are studied. The electrodeposited laccase-POPDA films are characterized by infrared spectra. The results prove that the enzyme secondary structure remains unchanged during the entrapment procedure. POPDA matrix structure consists of the phenazine-type polymer according to infrared spectra.     

Redox behaviour of cerium oxychloride in molten MgCl2-NaCl-KCl eutectic

The electrochemical behaviour of cerium oxychloride in MgCl₂-NaCl-KCl ternary eutectic was investigated by cyclic voltammetry at 823 K. The cyclic voltammogram of UO₂Cl₂-CeOCl in MgCl₂-NaCl-KCl eutectic shows two peaks during the cathodic sweep as well as anodic sweep. The reduction of UO₂²⁺ is by a single step two-electron transfer and that of CeO⁺ is by a single step one-electron transfer. The reduction of CeO⁺ was found to be quasi-reversible.The reduction potentials of UO₂²⁺/UO₂ and CeO⁺/CeO versus Ag(I)/Ag reference electrode at 823 K are 0.103 and −0.299 V, respectively. The diffusion coefficient of CeO⁺ at 823 K is in the range of (1.7-1.9) × 10⁻⁵ cm² s⁻¹. The cyclic voltammogram for 0.015 mol% CeOCl shows an additional peak during the anodic sweep at −0.056 V, which is being attributed to monolayer dissolution of CeO at the glassy carbon working electrode. Electrochemical impedance data of 0.015 mol% CeOCl in MgCl₂-NaCl-KCl eutectic at the open circuit potential was fitted to a Randles cell from which the heterogeneous rate constant was estimated. X-ray photoelectron spectroscopy was used to confirm that the oxidation state of cerium in the eutectic is +3.