Electrochemical behavior of folic acid on mercury meniscus modified silver solid amalgam electrode

Voltammetric behavior of folic acid and folates has been investigated using direct current voltammetry, differential pulse voltammetry and adsorptive stripping differential pulse voltammetry at a mercury meniscus modified silver solid amalgam electrode (m-AgSAE). The optimum conditions have been found for their determination in a 1:9 mixture of methanol and aqueous acetate buffer, with the limit of detection about 0.5 nmol L⁻¹. RSD at this concentration level amounted to less than 4%. Practical applicability of the newly developed method was verified by analysis of three vitamin preparations and of two multivitamin juices.     

Electrocatalytic and simultaneous determination of isoproterenol, uric acid and folic acid at molybdenum (VI) complex-carbon nanotube paste electrode

This paper describes the development, electrochemical characterization and utilization of a novel modified molybdenum (VI) complex-carbon nanotube paste electrode for the electrocatalytic determination of isoproterenol (IP). The electrochemical profile of the proposed modified electrode was analyzed by cyclic voltammetry (CV) that showed a shift of the oxidation peak potential of IP at 175 mV to less positive value, compared with an unmodified carbon paste electrode. Differential pulse voltammetry (DPV) in 0.1 M phosphate buffer solution (PBS) at pH 7.0 was performed to determine IP in the range from 0.7 to 600.0 μM, with a detection limit of 35.0 nM. Then the modified electrode was used to determine IP in an excess of uric acid (UA) and folic acid (FA) by DPV. Finally, this method was used for the determination of IP in some real samples.     

Study and determination of the herbicide cyclosulfamuron by square wave stripping voltammetry

The voltammeric behavior of the herbicide cyclosulfamuron has been studied by square wave stripping voltammetry (SWSV). Cyclosulfamuron was reduced on a static mercury drop electrode (SMDE) and gave a well-defined peak in the pH range of 3.0-7.0. The peak potential (E_p) shifts to a more negative potential with increasing pH. The ratio ΔE_p/ΔpH over the pH range studied was 59.5 mV/pH. A systematic study of the various experimental parameters that affect the stripping response was studied by SWV. The square wave parameters used were a frequency of 150 Hz, an amplitude of −60 mV and a staircase step of 6.0 mV. The quantifications were performed by the standard addition method, from the SW voltammetric peak obtained at −1348 mV. Calibration curves were linear in the range of 10-350 μg L⁻¹ with a detection limit of 3.5 μg L⁻¹ under the conditions used (pH 6.0 buffer solution, E_acc = −400 mV vs. Ag/AgCl, t_acc = 75 s). The validity of the developed methodology was assessed by recovery experiments at the 25-100 μg L⁻¹ level. The mean results for 3 determinations were 49.7 ± 3.3 μg L⁻¹, which is very close to the amount of cyclosulfamuron added to soil (50 μg L⁻¹), with a recovery of 99.4%. The sufficiently good recoveries and low relative standard deviation (RSD) data reflects the high accuracy and precision of the proposed SW voltammetric method. The possible influences of various inorganic species and other pesticides were also investigated.     

Voltammetric behavior study of folic acid at phosphomolybdic-polypyrrole film modified electrode

The electrochemical behavior of folic acid at the Keggin-type phosphomolybdate (PMo₁₂) doped polypyrrole (PPy) film modified glassy carbon electrode (PMo₁₂-PPy/GCE) was studied. PMo₁₂ doped PPy modified electrodes were achieved during the electrochemical preparation of the polymer films in aqueous solution. The redox behavior of the modified electrode was described by cyclic voltammetry. The electrochemical behavior of folic acid at PMo₁₂-PPy/GCE was studied by 0.5 order differential voltammetry. Numerous factors affecting the reduction peak currents of folic acid at PMo₁₂-PPy/GCE were optimized to maximize the sensitivity. The results showed that folic acid had high inhibitory activity toward the reduction of modified electrode in 0.01 M H₂SO₄. The reduction peak currents were directly proportional to the concentration of folic acid from 1.0 × 10⁻⁸ to 1 × 10⁻⁷ M with correlation coefficient of 0.9976, a detection limit of 1.0 × 10⁻¹⁰ M of folic acid was estimated. From the inhibitory effect of folic acid on PMo₁₂-PPy/GCE, the apparent formation constant of folic acid with the modified film was estimated. This modified electrode showed excellent sensitivity and stability for the determination of folic acid. The response mechanism of folic acid at PMo₁₂-PPy/GCE was discussed in detail.     

Determination of trace selenium by differential pulse adsorptive stripping voltammetry at a bismuth film electrode

The differential pulse adsorptive stripping voltammetric behavior of selenium (IV)-p-aminobenzene sulfonic acid-cetyltrimethylammonium bromide system at a bismuth-coated glassy carbon electrode (BiFE) has been investigated. A well-defined and sensitive stripping peak of the selenium (IV)-p-aminobenzene sulfonic acid complex was observed at −0.76 V (vs. SCE) in a 0.15 mol/L acetate solution (pH 2.9) at a deposition potential of −0.40 V (for 120 s). The linear range was 2-30 μg/L and the detection limit for an accumulation time of 300 s was 0.1 μg/L. This method was applied to determine the trace amount of selenium in the samples.     

Monolayer covalent modification of 5-hydroxytryptophan on glassy carbon electrodes for simultaneous determination of uric acid and ascorbic acid

5-Hydroxytryptophan (5-HTP) was covalently grafted on the surface of glassy carbon electrodes (GCEs) using cyclic voltammetric method in a phosphate buffer solution. The prepared electrode, denoded as 5-HTP/GCE, was characterized by X-ray photoelectron spectroscopy, cyclic voltammetry and differential pulse voltammetry (DPV). Tryptophan grafted GCE (TRP/GCE) and 5-hydroxytryptamine grafted GCE (5-HTP/GCE) were also prepared by the same method for comparison. It was found that the electrocatalytic activities toward the oxidation of uric acid (UA) and ascorbic acid (AA) was in the order of 5-HT/GCE > 5-HTP/GCE > TRP/GCE for UA oxidation and 5-HT/GCE = 5-HTP/GCE > TRP/GCE for AA oxidation. However, the CV current sensitivity was estimated as 4:2:1 for 5-HTP/GCE:5-HT/GCE:TRP/GCE. The DPV peaks for UA and AA oxidation appeared at 0.07 V and 0.34 V versus SCE, respectively, allowing simultaneous determination in mixtures. A linearly response in the range of: 5.0 × 10⁻⁷ to 1.1 × 10⁻⁵ M with the detection limit (s/n = 3) of 2.8 × 10⁻⁷ M for UA determination, and a linear response in the range of: 5.0 × 10⁻⁶ to 1.0 × 10⁻⁴ M with the detection limit of 4.2 × 10⁻⁶ M for AA determination were obtained. This electrode was used for UA and AA determinations in human urine samples satisfactorily.     

Electrochemical behavior of an anion-exchanger modified electrode prepared by sol-gel processing of an organofunctional silicon alkoxide

Sol-gel films prepared from quaternary amine functionalized silicon alkoxide precursor on electrode surfaces have been investigated as anion-exchange and permselective coatings for electroanalytical investigations. These modified electrodes were evaluated with Fe(CN)₆³⁻ and Ru(bpy)₃²⁺ as the analytes using cyclic voltammetry. At low solution pH, the anionic analyte preconcentrated within the functionalized sol-gel coating and resulted in an improvement in detection limit of about 2 orders of magnitude compared to bare electrodes, but the response for the cationic analyte was suppressed. The modified electrodes are rugged and reproducible and can be regenerated. We have also shown that the anion-exchange and permselective properties of the modified electrodes can be affected by the composition, concentration, and pH of the support electrolyte.     

Electrochemical behavior of acetaminophen and its detection on the PANI-MWCNTs composite modified electrode

A polyaniline-multi-walled carbon nanotubes (PANI-MWCNTs) composite modified electrode was fabricated and the electrochemical behaviors of acetaminophen on the PANI-MWCNTs composite modified electrode were investigated by using cyclic voltammetry (CV), single-potential step chronocoulometry and square-wave voltammetry (SWV). The results showed that this electrode exhibited excellent electrocatalytic effects on the redox of acetaminophen. Consequently, a simple and sensitive electroanalytical method was developed for the determination of acetaminophen. The oxidation peak current was proportional to the concentration of acetaminophen from 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol/L and 2.5 × 10⁻⁴ to 2.0 × 10⁻³ mol/L, respectively. The detection limit was 2.5 × 10⁻⁷ mol/L. The proposed method was used to detect acetaminophen in Composite Chlorzoxazone Tablets and the results were satisfying.     

Electrochemical characterization of poly(eriochrome black T) modified glassy carbon electrode and its application to simultaneous determination of dopamine, ascorbic acid and uric acid

A polymerized film of eriochrome black T (EBT) was prepared on the surface of a glassy carbon (GC) electrode in alkaline solution by cyclic voltammetry (CV). The redox response of the poly(EBT) film at the GC electrode appeared in a couple of redox peak in 0.1 M hydrochloride and the pH dependent peak potential was −55.1 mV/pH which was close to the Nernst behavior. The poly(EBT) film-coated GC electrode exhibited excellent electrocatalytic activity towards the oxidations of dopamine (DA), ascorbic acid (AA) and uric acid (UA) in 0.05 mM phosphate buffer solution (pH 4.0) and lowered the overpotential for oxidation of DA. The polymer film modified GC electrode conspicuously enhanced the redox currents of DA, AA and UA, and could sensitively and separately determine DA at its low concentration (0.1 μM) in the presence of 4000 and 700 times higher concentrations of AA and UA, respectively. The separations of anodic peak potentials of DA-AA and UA-DA reached 210 mV and 170 mV, respectively, by cyclic voltammetry. Using differential pulse voltammetry, the calibration curves for DA, AA and UA were obtained over the range of 0.1-200 μM, 0.15-1 mM and 10-130 μM, respectively. With good selectivity and sensitivity, the present method provides a simple method for selective detection of DA, AA and UA in biological samples.     

聚对苯二酚修饰电极测定多巴胺和L-色氨酸的电化学研究

制备了对苯二酚聚合膜修饰玻碳电极(PHQ/GCE),研究了多巴胺(DA)和L-色氨酸(L-Trp)在该电极上的电化学行为,以及支持电解质、溶液pH、扫描速率等对DA和L-Trp伏安响应的影响.实验发现,在pH 5.5的NaH2PO4-Na2HPO4缓冲溶液中,可用PHQ/GCE测定溶液中的DA和L-Trp,两者氧化峰电流均与浓度在1×10-3～5×10-6 mol/L范围内呈良好线性关系,相关系数分别为0.998 3和0.996 5,检出限分别为1×10-6 mol/L和5×10-7 mol/L,该方法简便快捷.     

Electrochemical preparation of epinephrine/Nafion chemically modified electrodes and their electrocatalytic oxidation of ascorbic acid and dopamine

Two types of epinephrine and cyclized epinephrine quinone films have been prepared using cyclic voltammetry from the epinephrine in the strong acidic solutions and neutral aqueous solutions over different scanning potential ranges. The cyclic voltammogram of the epinephrine film is characterized by one redox couple at about +0.5 V (versus Ag|AgCl) and cyclized epinephrine quinone film exhibits one redox couples at about −0.15 V (versus Ag|AgCl) .In addition to cyclic voltammetry and an electrochemical quartz crystal microbalance (EQCM) were used to study the growth mechanism of the epinephrine and cyclized epinephrine quinone molecules. The electrocatalytic oxidation of catecholamines (dopamine and norepinephrine) and also ascorbic acid were investigated in acidic aqueous solutions using epinephrine films. The rotating ring-disk electrode technique was used to investigate the mechanism of electrochemical oxidation of dopamine and ascorbic acid.     

Electrochemical behavior and adsorptive stripping voltammetric determination of quercetin at multi-wall carbon nanotubes-modified paraffin-impregnated graphite disk electrode

Multi-wall carbon nanotubes-modified paraffin-impregnated graphite disk was fabricated by using choline bond and catalyzer (MWCNT/Ch/WGE), and the properties were, respectively, investigated by field emission scanning electron microscope (FE-SEM) and X-ray photoelectron spectroscopy (XPS). Electrochemical behavior of quercetin was studied in detail by FE-SEM, UV-spectroelectrochemical and various electrochemical methods, which related with the two catechol hydroxyl groups and the other three hydroxyl groups, the former is electron-donating group with a two electron two proton reversible reaction, and is pH dependent. A highly sensitive adsorptive stripping voltammetric measurement (AdSV) for quercetin was also shown at this electrode. On the optimum conditions, the adsorptive stripping response of the peak (E = 0.15 V, 3 min accumulation) was proportional to the concentration in a range of 9.0 × 10⁻⁹ to 4.0 × 10⁻⁵ M. A detection limit of 4.8 × 10⁻⁹ M was obtained with a signal-to-noise ratio (s/n) of 3 and a good precision (R.S.D.: 2.1%, n: 9). Such attractive ability of MWCNT/Ch/WGE suggests a great promise for a quercetin amperometric sensor.     

Sensitive determination of Cd and Pb by differential pulse stripping voltammetry with in situ bismuth-modified zeolite doped carbon paste electrodes

Here we investigated the analytical performances of the bismuth-modified zeolite doped carbon paste electrode (BiF-ZDCPE) for trace Cd and Pb analysis. The characteristics of bismuth-modified electrodes were improved greatly via addition of synthetic zeolite into carbon paste. To obtain high reproducibility and sensitivity, optimum experimental conditions for bismuth deposition were studied. Voltammetric responses of the BiF-ZDCPEs prepared with different ratios of zeolite, carbon powder, and silicone, were examined under same conditions. The in situ plated (zeolite/graphite powder/silicone, 10/190/80 w/w) BiF-ZDCPEs exhibited the most sensitive response to Cd and Pb in 0.10 M acetate buffer (pH 4.5). The detection limits of the modified electrode were 0.08 μg L⁻¹ for Cd(II) and 0.10 μg L⁻¹ for Pb(II) based on three times the standard deviation of the baseline with a preconcentration time of 120 s under optimal conditions, respectively. The modified electrode showed well linear response to both Cd(II) and Pb(II) over the concentration range from 1.0 to 20.0 μg L⁻¹. The BiF-ZDCPEs were successfully applied to the determination of Cd(II) and Pb(II) in real samples, and the results were in agreement with those of atomic absorption spectroscopy (AAS).     

LabVIEW-based sequential-injection analysis system for the determination of trace metals by square-wave anodic and adsorptive stripping voltammetry on mercury-film electrodes

The development of a dedicated automated sequential-injection analysis apparatus for anodic stripping voltammetry (ASV) and adsorptive stripping voltammetry (AdSV) is reported. The instrument comprised a peristaltic pump, a multiposition selector valve and a home-made potentiostat and used a mercury-film electrode as the working electrodes in a thin-layer electrochemical detector. Programming of the experimental sequence was performed in LabVIEW 5.1. The sequence of operations included formation of the mercury film, electrolytic or adsorptive accumulation of the analyte on the electrode surface, recording of the voltammetric current-potential response, and cleaning of the electrode. The stripping step was carried out by applying a square-wave (SW) potential-time excitation signal to the working electrode. The instrument allowed unattended operation since multiple-step sequences could be readily implemented through the purpose-built software. The utility of the analyser was tested for the determination of copper(II), cadmium(II), lead(II) and zinc(II) by SWASV and of nickel(II), cobalt(II) and uranium(VI) by SWAdSV.     

Simultaneous detection of ascorbic acid, uric acid and homovanillic acid at copper modified electrode

The copper was deposited on glassy carbon (GC) and indium tin oxide (ITO) electrodes by electrochemical method. The copper structures on electrode were characterized by atomic force microscope, X-ray diffractometeric pattern and differential pulse voltammetric studies. Optimal conditions for uniform growth of copper structures on the electrode were established. Voltammetric sensor was fabricated using the copper deposited GC electrode for the simultaneous detection and determination of uric acid (UA) and homovanillic acid (HVA) in the presence of excess concentrations of ascorbic acid (AA). The voltammetric signals due to AA and UA oxidation were well separated with a potential difference of 400 mV and AA did not interfere with the measurement of UA and HVA at the GC/Cu electrode. Linear calibration curves were obtained in the concentration range 1-40 μM for AA and 20-50 μM for UA at physiological pH and a detection limit of 10 nM of UA in the presence of 10-fold excess concentrations of AA was achieved. The simultaneous detection of submicromolar concentrations of AA, UA and HVA was achieved at the GC/Cu electrode. The practical utility of the present GC/Cu modified electrode was demonstrated by measuring the AA content in Vitamin C tablet, UA content in human urine and blood serum samples with satisfactory results.     

氧化物修饰电极及其在电化学处理有机废水中的应用

对比分析了氧化物修饰电极的制备方法,主要包括溅射法、喷雾热解法、涂层热解法、溶胶-凝胶法、电沉积法等。介绍了国内外采用氧化物修饰电极处理含酚、硝基苯、氯酚、染料等难降解有机废水的应用情况,分析了该方法存在的一些问题,并展望了氧化物修饰电极在有机废水处理方面所具有的巨大潜力。     

Studies based on the electrochemical response of 2-(2-nitrophenyl)-1H-benzimidazole at chemically modified electrodes with over-oxidized poly-1-naphthylamine

The development of a simple and efficient method to 2-(2-nitrophenyl)-1H-benzimidazole (NB) electrochemical determination using a polymer film coated chemically modified electrode is described. A glassy carbon (GC) electrode was modified employing an electro-polymerized film of 1-naphtylamine (1-NAP) followed by an over-oxidation treatment in 0.2 M sodium hydroxide solution (poly-1-NAPox electrode).The electrochemical behaviour of NB at the poly-1-NAPox electrode was investigated in a mixture of 10% ethanol + 90% buffer solution (pH 2) by cyclic voltammetry (CV) and square-wave voltammetry (SWV). The experimental results suggested that the poly-1-NAPox electrode had a good effect on NB electrochemical response because it avoided the electrode surface fouling as a consequence of the adsorption of NB reduction products, which was found when a bare GC electrode was employed as the working electrode. The NB cathodic current was dependent on the polymeric film over-oxidation degree (α).NB could be determined in the range from 2 × 10⁻⁶ to 5 × 10⁻⁵ M. The NB detection and quantification limits were 5 × 10⁻⁷ and 1.7 × 10⁻⁶ M, respectively. The percent relative standard deviation of the peak current to 10-replicated measurement using 1.2 × 10⁻⁵ M NB solution was 1.4%. The method showed to be rapid, simple and with a good sensitivity.     

Nanomolar detection of rutin based on adsorptive stripping analysis at single-sided heated graphite cylindrical electrodes with direct current heating

A single-sided heated graphite cylindrical electrode (ss-HGCE) was designed. Compared to previous alternative current (AC) heating, much simpler and cheaper direct current (DC) heating supplier was adopted for the first time to perform adsorptive accumulation of rutin at ss-HGCE at elevated electrode temperature. This offers great promise for low cost, miniaturization and high compatibility with portability. The square wave voltammetry (SWV) stripping peak current was enhanced with increasing the electrode temperature only during preconcentration step. This enhancement was contributed to the forced thermal convection induced by heating the electrode rather than the bulk solution, which is able to improve mass transfer and facilitate adsorption hence enhance stripping response. A detection limit of 1.0 × 10⁻⁹ M (S/N = 3) could be obtained at an electrode temperature of 48 °C during 5 min accumulation, one magnitude lower than that at 28 °C (room temperature). This is the lowest value at carbon-based electrodes for rutin determination as we know. Such novel method was also successfully used to determine rutin in pharmaceutical tablets.     

Comparative investigation on electrochemical behavior of hydroquinone at carbon ionic liquid electrode, ionic liquid modified carbon paste electrode and carbon paste electrode

Ionic liquid, 1-heptyl-3-methylimidazolium hexafluorophosphate (HMIMPF₆), has been used to fabricate two new electrodes, carbon ionic liquid electrode (CILE) and ionic liquid modified carbon paste electrode (IL/CPE), using graphite powder mixed with HMIMPF₆ or the mixture of HMIMPF₆/paraffin liquid as the binder, respectively. The electrochemical behaviors of hydroquinone at the CILE, the IL/CPE and the CPE were investigated in phosphate buffer solution. At all these electrodes, hydroquinone showed a pair of redox peaks. The order of the current response and the standard rate constant of hydroquinone at these electrodes were as follows: CILE > IL/CPE > CPE, while the peak-to-peak potential separation was in an opposite sequence: CILE < IL/CPE < CPE. The results show the superiority of CILE to IL/CPE and CPE, and IL/CPE to CPE in terms of promoting electron transfer, improving reversibility and enhancing sensitivity. The CILE was chosen as working electrode to determine hydroquinone by differential pulse voltammetry, which can be used for sensitive, simple and rapid determination of hydroquinone in medicated skin cosmetic cream.     

Adsorptive and stripping behavior of methylene blue at gold electrodes in the presence of cationic gemini surfactants

The adsorptive and stripping behavior of methylene blue (i.e. methylene blue chloride, MB) at a gold electrode has been studied with voltammetry, alternating current impedance spectra (ACIS) and quartz crystal microbalance (QCM). MB exhibits a pair of cyclic voltammetry peaks at about −0.3 V (versus SCE) in 0.05 M pH 6.9 phosphate buffer solutions. In the presence of cationic gemini surfactants such as C₁₆H₃₃N(CH₃)₂-C₄H₈-N(CH₃)₂C₁₆H₃₃Br₂ (C₁₆-C₄-C₁₆), C₁₆H₃₃N(CH₃)₂-C₄H₇OH-N(CH₃)₂C₁₆H₃₃Br₂ (C₁₆-C₄OH-C₁₆), C₁₆H₃₃N(CH₃)₂-CH₂-C₆H₄-CH₂-N(CH₃)₂C₁₆H₃₃Br₂ (C₁₆-ph-C₁₆) and C₁₆H₃₃N(CH₃)₂-C₁₂H₂₄-N(CH₃)₂C₁₆H₃₃Br₂ (C₁₆-C₁₂-C₁₆), the anodic peak grows rapidly and moves in positive direction, but the cathodic peak gradually decreases, due to the association adsorption and electrostatic interaction of the geminis with MB and its reduced product (i.e. leuko methylene blue, LMB). With the aid of geminis the adsorption amount of MB increases under open-circuit, but the impedance of the mixed adsorption film to Fe(CN)₆^3−/4− almost keeps unchanged, compared with either bare gold electrodes or MB film, while the adsorption film of geminis exhibits greater impedance. This probably is due to the electron medium action of MB in the film. Gemini surfactants with same alkyl-chain (i.e. -(CH₂)₁₅CH₃) but different molecular structure, exhibit different influence. The enhancing action of geminis studied follows such order as: C₁₆-ph-C₁₆ > C₁₆-C₄-C₁₆ > C₁₆-C₄OH-C₁₆ > C₁₆-C₁₂-C₁₆. The change of peak potential was ascribed to the interaction between MB and surfactants, as well as the blocking action of surfactant film. For comparison, the influence of dihexadecyldimethylammonium bromide (DCAB) and cetyltrimethylammonium bromide (CTAB) was studied, and the influence of other factors is discussed as well.