Gel polymer electrolyte based on poly(acrylonitrile-co-styrene) and a novel organic iodide salt for quasi-solid state dye-sensitized solar cell

A gel polymer electrolyte based on poly(acrylonitrile-co-styrene) as polymer matrix and N-methyl pyridine iodide salt as I⁻ source was prepared. Controlling the concentration of polymer matrix of poly(acrylonitrile-co-styrene) at 17.5 wt.%, mixing the binary organic solvents mixture ethylene carbonate and propylene carbonate with 6:4 (w/w), and the concentration of N-methyl pyridine iodide and iodine with 0.5 and 0.05 M, respectively, the gel polymer electrolyte attains the maximum ionic conductivity (at 30 °C) of 4.63 mS cm⁻¹. Based on the gel polymer electrolyte, a quasi-solid state dye-sensitized solar cell was fabricated and its overall energy conversion efficiency of light-to-electricity of 3.10% was achieved under irradiation of 100 mW cm⁻².     

Novel chemically cross-linked solid state electrolyte for dye-sensitized solar cells

Poly(vinylpyridine-co-ethylene glycol methyl ether methacrylate) (P(VP-co-MEOMA)) and α,ω-diiodo poly(ethylene oxide-co-propylene oxide) (I[(EO)_0.8-co-(PO)_0.2]_yI) were synthesized and used as chemically cross-linked precursors of the electrolyte for dye-sensitized solar cells. Meanwhile, α-iodo poly(ethylene oxide-co-propylene oxide) methyl ether (CH₃O[(EO)_0.8-co-(PO)_0.2]_xI) was synthesized and added into the electrolyte as an internal plasticizer. Novel polymer electrolyte resulting from chemically cross-linked precursors was obtained by the quaterisation at 90 °C for 30 min. The characteristics for this kind of electrolyte were investigated by means of ionic conductivity, thermogravimetric and photocurrent-voltage. The ambient ionic conductivity was significantly enhanced to 2.3 × 10⁻⁴ S cm⁻¹ after introducing plasticizer, modified-ionic liquid. The weight loss of the solid state electrolyte at 200 °C was 1.8%, and its decomposition temperature was 287 °C. Solid state dye-sensitized solar cell based on chemically cross-linked electrolyte presented an overall conversion efficiency of 2.35% under AM1.5 irradiation (100 mW cm⁻²). The as-fabricated device maintained 88% of its initial performance at room temperature even without sealing for 30 days, showing a good stability.     

Influence of molecular weight of PEG on the property of polymer gel electrolyte and performance of quasi-solid-state dye-sensitized solar cells

A new kind of polymer gel electrolyte based on poly(acrylic acid)-poly(ethylene glycol) (PAA-PEG) hybrid was synthesized. The factor of molecular weight of PEG in the hybrid plays an important role in determining the liquid electrolyte absorbency of the hybrid and ionic conductivity of the polymer gel electrolyte, sequentially affects the photovoltaic performance of quasi-solid-state dye-sensitized solar cells. Using the hybrid with PEG molecular weight of 20,000, a polymer gel electrolyte with liquid electrolyte absorbency of 6.9 g g⁻¹ and ionic conductivity of 5.35 mS cm⁻¹ was obtained. Based on the polymer gel electrolyte, a quasi-solid-state dye-sensitized solar cell with conversion efficiency of 5.25% was achieved under irradiation of AM 1.5, 100 mW cm⁻².     

A study of hydrogel thermal-dynamics using Fourier transform infrared spectrometer

A rapid and reliable method was presented for studying hydrogel dynamics/kinetics. Two temperature-sensitive hydrogels, poly-N-isopropylacrylamide (poly(NIPAAm)) and the copolymer of N,N-diethylacrylamide and sodium methacrylate (molar ratio=97:3, poly(NDEAAm-co-MAA)) were synthesized. The thermal-behaviors of the gels were studied through the absorbance intensities of both swollen water and gel frame components, and the peak positions of amide band along heating/cooling pathways under dynamic Fourier transform infrared (FTIR) probing. The results showed that the lower critical solution temperature (LCST) of poly(NIPAAm) is about 33-35 °C, which is consistent with reported value of ∼34 °C. Compared to poly(NIPAAm), poly(NDEAAm-co-MAA) has relatively continuous volume phase transition, starting at ∼35 °C and a better thermal-reversibility with similar swelling and deswelling profiles over a larger temperature range (10-80 °C for poly(NDEAAm-co-MAA) vs. 10-33 °C for poly(NIPAAm)). The H-bonding water along phase transition was also studied, showing a less reversibility of poly(NIPAAm) compared to poly(NDEAAm-co-MAA). In addition, FTIR spectrometer was also used to study the volume changes of poly(NDEAAm-co-MAA) under variations in environmental salinity.     

Influence of solvent on the poly (acrylic acid)-oligo-(ethylene glycol) polymer gel electrolyte and the performance of quasi-solid-state dye-sensitized solar cells

The influence of solvents on the property of poly (acrylic acid)-oligo-(ethylene glycol) polymer gel electrolyte and photovoltaic performance of quasi-solid-state dye-sensitized solar cells (DSSCs) were investigated. Solvents or mixed solvents with large donor number enhance the liquid electrolyte absorbency, which further influences the ionic conductivity of polymer gel electrolyte. A polymer gel electrolyte with ionic conductivity of 4.45 mS cm⁻¹ was obtained by using poly (acrylic acid)-oligo-(ethylene glycol) as polymer matrix, and absorbing 30 vol.% N-methyl pyrrolidone and 70 vol.% γ-butyrolactone with 0.5 M NaI and 0.05 M I₂. By using this polymer gel electrolyte coupling with 0.4 M pyridine additive, a quasi-solid-state dye-sensitized solar cell with conversion efficiency of 4.74% was obtained under irradiation of 100 mW cm⁻² (AM 1.5).     

Preparation of a microporous polymer electrolyte based on poly(vinyl chloride)/poly(acrylonitrile-butyl acrylate) blend for Li-ion batteries

Poly(acrylonitrile-co-butyl acrylate) (P(AN-co-BuA))/poly(vinyl chloride) (PVC) blend-based gel polymer electrolyte (BGPE) was prepared for lithium-ion batteries. The P(AN-co-BuA)/PVC BGPE consists of an electrolyte-rich phase, which is mainly composed of P(AN-co-BuA) and liquid electrolyte, acting as a conducting channel and a PVC-rich phase that provides mechanical strength. The dual phase was just simply developed by the difference of miscibility properties in solvent, PC, between P(AN-co-BuA) and PVC. The mechanical strength of this new blend electrolyte was found to be much higher, with a fracture stress as high as 29 MPa in dry membrane and 21 MPa in gel state, than that of a previously reported P(AN-co-BuA)-based gel polymer electrolyte. The blended gel polymer electrolyte showed ionic conductivity of higher than 1.5 × 10⁻³ S cm⁻¹ and electrochemical stability up to at least 4.8 V. The results showed that the as-prepared gel polymer electrolytes were promising materials for lithium-ion batteries.     

Application of poly(acrylic acid-g-gelatin)/polypyrrole gel electrolyte in flexible quasi-solid-state dye-sensitized solar cell

A novel gel polymer electrolyte based on poly(acrylic acid-g-gelatin)/polypyrrole with conductivity of 14.1 mS cm⁻¹ was prepared. Based on the gel electrolyte, a flexible quasi-solid-state dye-sensitized solar cell was fabricated by using a low-temperature filming technique. Owing to high conductivity and the catalytic function of polypyrrole for I⁻/I₃⁻ redox reaction for the gel electrolyte, the flexible quasi-solid-state dye-sensitized solar cell showed a light-to-electric energy conversion efficiency of 1.28%, under a simulated solar light irradiation with intensity of 100 mW cm⁻² (AM 1.5).     

Synthesis of novel nanoreinforcements for polymer matrices by ATRP: Triblock poly(rotaxan)s based in polyethyleneglycol end-caped with poly(methyl methacrylate)

Poly(rotaxan)s of poly(ethylene glycol) and α-cyclodextrines (CD) block copolymers end-capped with poly(methyl methacrylate) chains were synthesized by atom transfer radical polymerization. The synthesized copolymers were characterized by ¹H NMR, 2D NOESY NMR, X-ray and Thermogravimetric analysis. Assuming a maximum relation of 2 CDs per ethyleneglycol unit, a coverage degree of 18% and 15% was achieved. X-ray analysis showed a characteristic signal around 20θ for all copolymers with an amorphous halo mainly due to inter-crystal poly(ethylene glycol) and poly(methyl methacrylate) chains. Full Molecular Dynamics of 20 ns was used to simulate the crystal structure of these copolymers. A pair correlation function was used to determine the coupling between hydrogen atoms of PEG, PMMA and cyclodextrine obtained by 2D NOESY NMR.     

Influence of ionic additives NaI/I2 on the properties of polymer gel electrolyte and performance of quasi-solid-state dye-sensitized solar cells

The ionic additives NaI/I₂ in polymer gel electrolyte not only provide cations, but also affect the liquid electrolyte absorbency of the poly(acrylic acid)-poly(ethylene glycol) hybrid, which results in the change of ionic conductivity of polymer gel electrolyte and the photovoltaic performance of quasi-solid-state dye-sensitized solar cell. With the optimized components of liquid electrolyte containing 0.5 M NaI, 0.05 M I₂, 0.4 M pyridine, 70 vol.% γ-butyrolactone and 30 vol.% N-methylpyrrolidone, a 4.74% power conversion efficiency of quasi-solid-state dye-sensitized solar cell was obtained under 100 mW cm⁻² (AM 1.5) irradiation.     

Controlled synthesis and characterizations of amphiphilic poly[(R,S)-3-hydroxybutyrate]-poly(ethylene glycol)-poly[(R,S)-3-hydroxybutyrate] triblock copolymers

Well-defined biodegradable amphiphilic triblock copolymers consisting of atactic poly[(R,S)-3-hydroxybutyrate] (PHB) and poly(ethylene glycol) (PEG) as the side hydrophobic block and middle hydrophilic block were synthesized via ring opening polymerization of (R,S)-β-butyrolactone from PEG macroinitiators and characterized using NMR, GPC, FT-IR, XRD, DSC and TG analyses. The controlled synthesis was made possible by the facile synthesis of pure PEG macroinitiators through a TEMPO-mediated oxidation. Constituting 40-70 wt% of the copolymer content, PHB blocks grown were amorphous while PEG formed crystalline phase when segment was sufficiently long. While hindering PEG crystallization, atactic PHB mixed well with amorphous PEG to give single T_g in all the copolymers. The copolymers exhibited two-step thermal degradation profile starting with PHB degradation from 210 to 300 °C, then PEG from 350 to 450 °C.     

Synthesis and properties of ABA-type triblock copolymers of poly(glycolide-co-caprolactone) (A) and poly(ethylene glycol) (B)

Poly(glycolide-co-caprolactone) (A)-poly(ethylene glycol) (B) ABA-type triblock copolymers (PGCE) were synthesized by bulk ring opening polymerization, using the hydroxyl endgroups of poly(ethylene glycol) (PEG) as initiator and stannous octoate as catalyst. The resulting copolymers were characterized by various analytical techniques. Gel permeation chromatographic analysis indicated that the polymerization product was free of residual monomers, PEG and oligomers. ¹H NMR and differential scanning calorimeter results demonstrated that the copolymers had a structure of poly(glycolide-co-caprolactone) (PGC) chains chemically attached to PEG segments. All the PGCE copolymers showed improved hydrophilicity in comparison with the corresponding PGC copolymers with the same molar ratio of glycolidyl and caproyl units. The microspheres of PGCE copolymer exhibited rough surfaces quite different from the smooth surface of PGC microspheres. This phenomenon was attentively ascribed to the highly swollen ability of PGCE copolymers and the freeze-drying process in the microspheres fabrication.     

Synthesis and thermally responsive characteristics of dendritic poly(ether-amide) grafting with PNIPAAm and PEG

A series of thermally responsive dendritic core-shell polymers were prepared based upon dendritic poly(ether-amide) (DPEA), modified with carboxyl end-capped linear poly(N-isopropylacrylamide) (PNIPAAm-COOH) or both PNIPAAm-COOH and carboxyl end-capped methoxy polyethylene glycol (PEG-COOH) in different ratios via an esterification process to obtain DPEA-PNIPAAm or DPEA-PNIPAAm-PEG. Their molecular structures were verified by gel permeation chromatography, and ¹H NMR and FTIR spectroscopy. The temperature-dependent characteristics study has revealed that DPEA-PNIPAAm exhibits a lower critical solution temperature (LCST) of about 34 °C, whereas DPEA-PNIPAAm-PEG polymers with the PNIPAAm/PEG ratio of about 1.0 and 0.4 possess about 36 °C and 39 °C, respectively, compared with 32 °C for homopolymer PNIPAAm. The critical aggregation temperature was investigated using fluorescence excitation spectrum of pyrene as a sequestered guest molecule based upon the sharp increase of the I₃₃₈/I₃₃₃ value.     

Multi-methacrylated star-shaped,photocurable poly(methyl methacrylate) macromonomers via quasiliving ATRP with suppressed curing shrinkage

Novel, star-shaped multifunctional poly(methyl methacrylate) (PMMA) macromonomers with well-defined average number of pendant methacrylate groups were synthesized by copolymerizing MMA with 2-hydroxyethyl methacrylate (HEMA) via quasiliving ATRP with a tetrafunctional initiator in methanol at 10 °C, followed by methacrylation of the hydroxyl groups of the HEMA units. The resulting tailor-made poly(methyl methacrylate-co-2-methacryloylethyl methacrylate), P(MMA-co-MEMA), multifunctional macromonomers were used as cross-linking agents in photocuring of MMA, a solvent for its own polymer, and thus chemically homogeneous PMMA networks were formed in which the tetrafunctional initiator moiety provides inherent, additional branching points in the resulting cross-linked materials. This approach, even in the presence of relatively low amounts of macromonomers of ∼35–45%, provides sol-free products and up to ∼40% less polymerization shrinkage than that by curing of MMA with a conventional low molecular weight bifunctional methacrylate. These new, unique star-shaped PMMA macromonomers are potential cross-linkers in a variety of solvent-free applications where low curing shrinkage and high conversions are critical requirements, such as in several engineering materials, coatings, dental fillings and restorations, bone cements etc.     

Synthesis of rapid responsive gels comprising hydrophilic backbone and poly(N-isopropylacrylamide) graft chains by RAFT polymerization and end-linking processes

A thermosensitive poly(N-isopropylacrylamide) (PNIPAM) grafted gel, which comprises hydrophilic backbone and freely mobile PNIPAM graft chains, was synthesized by reversible addition fragmentation chain transfer (RAFT) polymerization and end-linking processes. Functional PNIPAM bearing dithiobenzoate end group (-C(S)S-R) was prepared first, and then it was reacted with divinyl compounds to obtain gel. In order to adjust the composition of the gels, two divinyl compounds, N,N-methylenebisacrylamide (BIS) and poly(ethylene glycol) diacrylate (PEGDAC), were used. The cross-linking polymerization mechanism was proposed. The swelling and deswelling kinetics of the hydrogels were measured. The gels exhibit rapid deswelling kinetics. At the same time, they show rapid swelling kinetics within 30 min, whereas a conventional PNIPAM-co-PEG-co-BIS gel with the same feed composition requires more than 10 h to reach swelling equilibrium.     

Preparation of core cross-linked micelles using a photo-cross-linking agent

A new method for preparing polymeric, core cross-linked (CCL) micelles has been developed using a bifunctional photo-cross-linking agent of di(4-hydroxyl benzophenone) dodecanedioate (BPD). An amphiphilic diblock copolymer of poly(ethylene glycol)-b-poly(2-hydroxyethyl methacrylate-co-methyl methacrylate) (PEG-b-P(HEMA-co-MMA)) was synthesized via atom-transfer radical polymerization (ATRP) using a PEG macroinitiator at 85 °C. The core domains of the PEG-b-P(HEMA-co-MMA) micelles containing BPD in aqueous solution were successfully photo-cross-linked by UV irradiation for only 30 min. The HEMA units incorporated in the hydrophobic block of PEG-b-P(HEMA-co-MMA) donated labile hydrogens to excited-state BP groups in BPD, and they were subsequently cross-linked by BPD through radical-radical combination. A sufficient degree of cross-linking was obtained at an equivalent ratio of the BP groups to the HEMA units.     

Synthesis and electrochemical properties of lithium methacrylate-based self-doped gel polymer electrolytes

In this study, a strategy for synthesizing lithium methacrylate (LiMA)-based self-doped gel polymer electrolytes was described and the electrochemical properties were investigated by impedance spectroscopy and linear sweep voltammetry. LiMA was found to dissolve in ethylene carbonate (EC)/diethyl carbonate (DEC) (3/7, v/v) solvent after complexing with boron trifluoride (BF₃). This was achieved by lowering the ionic interactions between the methacrylic anion and lithium cation. As a result, gel polymer electrolytes consisting of BF₃-LiMA complexes and poly(ethylene glycol) diacrylate were successfully synthesized by radical polymerization in an EC/DEC liquid electrolyte. The FT-IR and AC impedance measurements revealed that the incorporation of BF₃ into the gel polymer electrolytes increases the solubility of LiMA and the ionic conductivity by enhancing the ion disassociations. Despite the self-doped nature of the LiMA salt, an ionic conductivity value of 3.0 × 10⁻⁵ S cm⁻¹ was achieved at 25 °C in the gel polymer electrolyte with 49 wt% of polymer content. Furthermore, linear sweep voltammetry measurements showed that the electrochemical stability of the gel polymer electrolyte was around 5.0 V at 25 °C.     

Synthesis and characterization of amphiphilic graft copolymer poly(ethylene oxide)-graft-poly(methyl acrylate)

A novel well-defined amphiphilic graft copolymer of poly(ethylene oxide) as main chain and poly(methyl acrylate) as graft chains is successfully prepared by combination of anionic copolymerization with atom transfer radical polymerization (ATRP). The glycidol is protected by ethyl vinyl ether first, then obtained 2,3-epoxypropyl-1-ethoxyethyl ether (EPEE) is copolymerized with EO by initiation of mixture of diphenylmethyl potassium and triethylene glycol to give the well-defined poly(EO-co-EPEE), the latter is deprotected in the acidic conditions, then the recovered copolymer [(poly(EO-co-Gly)] with multi-pending hydroxyls is esterified with 2-bromoisobutyryl bromide to produce the ATRP macroinitiator with multi-pending activated bromides [poly(EO-co-Gly)_(ATRP)] to initiate the polymerization of methyl acrylate (MA). The object products and intermediates are characterized by NMR, MALDI-TOF-MS, FT-IR, and SEC in detail. In solution polymerization, the molecular weight distribution of the graft copolymers is rather narrow (M_w/M_n < 1.2), and the linear dependence of Ln [M₀]/[M] on time demonstrates that the MA polymerization is well controlled.     

pH-sensitive and bioadhesive poly(β-amino ester)-poly(ethylene glycol)-poly(β-amino ester) triblock copolymer hydrogels with potential for drug delivery in oral mucosal surfaces

A series of novel pH-sensitive triblock copolymers composed of poly(β-amino ester)-poly(ethylene glycol)-poly(β-amino ester) (PAE-PEG-PAE) were synthesized by conjugating poly(β-amino ester) to poly(ethylene glycol). The resulting polymers were characterized by ¹H and ¹³C NMR in CDCl₃ and gel permeation chromatography in tetrahydrofuran. The concentrated polymer solutions (30 wt%) exhibited a gel-to-sol transition in the pH range 6.4-7.8. The gel window spanned physiological conditions (37 °C, pH 7.4). After injection into a rat, the copolymer solution (30 wt%) changed to a gel in a short time. This copolymer hydrogel showed bioadhesive properties and in vitro release of lidocaine was controllable.     

Thermo-sensitive sol-gel transition of poly(depsipeptide-co-lactide)-g-PEG copolymers in aqueous solution

A series of biodegradable graft copolymers composed of poly(ethylene glycol) side-chains and a poly(depsipeptide-co-dl-lactide) backbone (PDG-dl-LA-g-PEG) were prepared as a novel thermo-gelling system. An aqueous solution of PDG-dl-LA-g-PEG (20 wt%) with a certain PEG length and composition showed instantaneous temperature-sensitive gelation at 33 °C. The sol-gel transition temperature (T_gel) could be controlled from 33 to 51 °C by varying the PEG length and compositions without a decrease in mechanical strength of the hydrogels. The 20 wt% hydrogel was eroded gradually in PBS at 37 °C for 60 days. This research provides a molecular design approach to create biodegradable thermo-gelling polymers with controllable T_gel and mechanical toughness.     

Composite polyether electrolytes with a poly(styrenesulfonate) lithium salt and Lewis acid type additive

A poly(styrenesulfonate) lithium salt was tested as a single-ion conductor in a poly(ethylene oxide)/poly(ethylene glycol) dimethyl ether matrix. Impedance spectroscopy and voltage step polarization were used to characterize the composite electrolytes. A specific conductivity of about 7×10⁻⁸ S cm⁻¹ was evaluated at 70 °C. The very low conductivity was attributed to the poor solubility of Li⁺ in the polymer matrix. AlCl₃ was added to the polymer electrolyte to increase the salt dissolution. The addition of the Lewis acid strongly increases the conductivity and a specific conductivity of about 4×10⁻⁶ S cm⁻¹ was measured at 20 °C. For temperature lower than 60 °C, the specific conductivity dependence with increasing temperature follows an Arrhenius-type behavior. An activation energy of about 55.6 kJ mol⁻¹ was calculated. A very similar activation energy (60.3 kJ mol⁻¹) was found for the charge transfer resistance. The transport properties of the polymer electrolyte were tested by applying a d.c. voltage step to a symmetrical lithium cell. The current at the applied voltage decreased with time. The decrease was related to an increase in the cell resistance due to the continuous growth of a passivation layer on the lithium surface.