Enhanced performance of LiFePO4 through hydrothermal synthesis coupled with carbon coating and cupric ion doping

A hydrothermal reaction has been adopted to synthesize pure LiFePO₄ first, which was then modified with carbon coating and cupric ion (Cu²⁺) doping simultaneously through a post-heat treatment. X-ray diffraction patterns, transmission electron microscopy and scanning electron microscopy images along with energy dispersive spectroscopy mappings have verified the homogeneous existence of coated carbon and doped Cu²⁺ in LiFePO₄ particles with phospho-olivine structure and an average size of 400 nm. The electrochemical performances of the material have been studied by cyclic voltammetry, electrochemical impedance spectroscopy and galvanostatic charge–discharge measurements. The carbon-coated and Cu²⁺-doped LiFePO₄ sample (LFCu5/C) exhibited an enhanced electronic conductivity of 2.05 × 10⁻³ S cm⁻¹, a specific discharge capacity of 158 mAh g⁻¹ at 50 mA g⁻¹, a capacity retention of 96.4% after 50 cycles, a decreased charge transfer resistance of 79.4 Ω and superior electrode reaction reversibility. The present synthesis route is promising in making the hydrothermal method more practical for preparation of the LiFePO₄ material and enhancement of electrochemical properties.     

Synthesis of LiFePO4/C cathode material from ferric oxide and organic lithium salts

LiFePO₄/C cathode material has been simply synthesized via a modified in situ solid-state reaction route using the raw materials of Fe₂O₃, NH₄H₂PO₄, Li₂C₂O₄ and lithium polyacrylate (PAALi). The sintering temperature of LiFePO₄/C precursor is studied by thermo-gravimetric (TG)/differential thermal analysis (DTA). The physical properties of LiFePO₄/C are then investigated through analysis using by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM) and the electrochemical properties are investigated by electrochemical impedance spectra (EIS), cyclic voltammogram (CV) and constant current charge/discharge test. The LiFePO₄/C composite with the particle size of ∼200 nm shows better discharge capacity (156.4 mAh g⁻¹) than bare LiFePO₄ (52.3 mAh g⁻¹) at 0.2 C due to the improved electronic conductivity which is demonstrated by EIS. The as-prepared LiFePO₄/C through this method also shows excellent high-rate characteristic and cycle performance. The initial discharge capacity of the sample is 120.5 mAh g⁻¹ and the capacity retention rate is 100.6% after 50 cycles at 5 C rate. The results prove that the using of organic lithium salts can obtain a high performance LiFePO₄/C composite.     

Long-term cyclability of nanostructured LiFePO4

Amorphous LiFePO₄ was obtained by lithiation of FePO₄ synthesized by spontaneous precipitation from equimolar aqueous solutions of Fe(NH₄)₂(SO₄)₂·6H₂O and NH₄H₂PO₄, using hydrogen peroxide as oxidizing agent. Nano-crystalline LiFePO₄ was obtained by heating amorphous nano-sized LiFePO₄ for different periods of time. The materials were characterized by TG, DTA, X-ray powder diffraction, scanning electron microscopy (SEM) and BET. All materials showed very good electrochemical performance in terms of energy and power density. Upon cycling, a capacity fading affected the materials, thus reducing the electrochemical performance. Nevertheless, the fading decreased upon cycling and after the 200th cycle the cell was able to cycle for more than 500 cycles without further fading.     

Effects of neodymium aliovalent substitution on the structure and electrochemical performance of LiFePO4

LiFe_1−xNd_xPO₄/C (x = 0-0.08) cathode material was synthesized using a solid-state reaction. The synthesis conditions were optimized by thermal analysis of the precursor and magnetic properties of LiFePO₄/C. The structure and electrochemical performances of the material were studied using XRD, FE-SEM, EDS, electrochemical impedance spectroscopy and galvanostatic charge-discharge. The results show that a small amount of aliovalent Nd³⁺ ion-dopant substitution on Fe²⁺ ions can effectively reduce the particle size of LiFePO₄/C. Cell parameters of LiFe_1−xNd_xPO₄ (x = 0.04-0.08) were calculated, and the results showed that LiFe_1−xNd_xPO₄/C had the same olivine structure as LiFePO₄. LiFe_0.4Nd_0.6PO₄/C delivers the discharge capacity of 165.2 mAh g⁻¹ at rate of 0.2 C and the capacity retention rate is 92.8% after 100 cycles. Charge-transfer resistance decreases with the addition of glucose and Nd³⁺ ions. Poly(cyclotriphosphazene-co-4,4′-sulfonyldiphenol) (PZS) was synthesized and PZS nanorods were used as a carbon source to coat LiFePO₄. All of the results show that aliovalent doping substitution of Fe in LiFePO₄ is well tolerated.     

Enhanced rate performance of nano–micro structured LiFePO4/C by improved process for high-power Li-ion batteries

A spherical carbon-coated nano–micro structured LiFePO₄ composite is synthesized for use as a cathode material in high-power lithium-ion batteries. The composites are synthesized through carbothermal reduction with two sessions of ball milling (before and after pre-sintering of precursor) followed by spray-drying with the dispersant of polyethylene glycol added. The structure, particle size, and surface morphology of the cathode active material and the properties of the coated carbon are investigated by X-ray diffraction, Raman spectroscopy, scanning electron microscopy, and high-resolution transmission electron microscopy. Results indicate that the LiFePO₄/C composite has a spherical micro-porous morphology composed of a large number of carbon-coated nano-spheres linked together with an ordered olivine structure. The carbon on the surface of LiFePO₄ effectively reduces inter-particle agglomeration of the LiFePO₄ particles. A galvanostatic charge–discharge test indicates that the LiFePO₄/C composites exhibit initial discharge capacities of 155 mAh g⁻¹ and 88 mAh g⁻¹ at 0.2 C and 20 C rates with the end of discharge voltage of 2.5 V, respectively. This behavior is ascribed to the unique spherical structure, which shortens lithium ions diffusion length and improves the electric contact between LiFePO₄ particles.     

掺杂Ni、Mn和Cu对磷酸铁锂电化学性能的影响

采用水热法合成了分别用Ni、Mn和Cu取代LiFePO4晶格中部分Fe位的掺杂LiMxFe1–xPO4（M=Ni、Mn、Cu;x=0.075、0.100、0.125、0.150、0.175）。对样品的物相结构和电化学性能进行了表征及测试,结果表明：制备的LiMxFe1–xPO4均为LiFePO4的基本结构,空间群为Pn...     

Effects of Na and Cl co-doping on electrochemical performance in LiFePO4/C

Na⁺ and Cl⁻ co-doped LiFePO₄/C composites were prepared via a simple solid state reaction. The structure, valence state and electrochemical performance were carefully investigated. Rietveld refinement on X-ray diffractions reveals that Na⁺ and Cl⁻ have successfully been introduced into the lattice of LiFePO₄. X-ray photoelectron spectroscopy proves that the co-doping of Na⁺ and Cl⁻ does not change the chemical state of Fe(II). Experimental results further show that the co-doping contributes to induce the lattice distortion, modify the particle morphology, and increase the electronic conductivity. Considerably enhanced capacity, coulombic efficiency and rate capability were obtained in the co-doped LiFePO₄. The specific capacities are 157 mAh g⁻¹ at 0.2 C, 115 mAh g⁻¹ at 10 C and 98 mAh g⁻¹ at 20 C for the (Na⁺, Cl⁻) co-doped LiFePO₄/C cathode material. The improvement can be ascribed to the enhanced electronic conductivity and electrode kinetics due to the micro-structural modification promoted by co-doping.     

Improved electrochemical performance of LiFePO4 by increasing its specific surface area

Cathode material LiFePO₄ with an excellent rate capability has been successfully prepared by a simple solid state reaction method using LiCH₃COO·2H₂O, FeC₂O₄·2H₂O and (NH₄)₂HPO₄ as the starting materials. We have investigated the effects of the sintering temperature and mixing time of the starting materials on the physical properties and electrochemical performance of LiFePO₄. It was found that the rate capability of LiFePO₄ is mainly controlled by its specific surface area and it is an effective way to improve the rate capability of the sample by increasing its specific surface area. In the present study, our prepared LiFePO₄ with a high specific surface area of 24.1 m² g⁻¹ has an excellent rate capability and can deliver 115 mAh g⁻¹ of reversible capacity even at the 5 C rate. Moreover, we have prepared lithium ion batteries based on LiFePO₄ as the cathode material and MCMB as the anode material, which showed an excellent cycling performance.     

Enhanced electrochemical performance of LiFePO4/C via Mo-doping at Fe site

A series of Mo-doped LiFe_1−3xMo_xPO₄/C (x = 0.000, 0.025, 0.050, 0.100, 0.150) cathode materials are synthesized by sol–gel method. XRD, ICP and Rietveld refinement results reveal that Mo doped in the crystal lattice and probably occupied Fe site. The structure benefits the transportation of Li⁺ and the diffusion of Li⁺ in the doped materials are enhanced remarkably than that of the undoped one, which leads to excellent electrochemical performance. The doped sample with x = 0.025 exhibits the best electrochemical performance, with the initial discharge capacity of 162.3 mAh g⁻¹ at 0.1 C rate.     

An effective and simple way to synthesize LiFePO4/C composite

The cathode material is synthesized from FeC₂O₄·2H₂O and LiH₂PO₄ by a solid-state reaction using citric acid as a carbon source. The electric conductivity of the synthesized LiFePO₄ has been raised by eight orders of magnitude from 10⁻⁹ S cm⁻¹. The LiFePO₄/C composite shows a greatly enhanced rate performance and the cyclic stability at room temperature. It delivers an initial discharge capacity of 128 mAh g⁻¹ at 4C, which is retained as high as 92% after 1000 cycles. In addition, the tested low temperature character is attractive. At −20 °C, the composite exhibits a discharge capacity of 110 mAh g⁻¹ at 0.1C. The homogenous morphology, the porous surface, the small particles inside and the conductive carbon observed contribute much to obtain the favorable electrochemical performance.     

Investigation on diffusion behavior of Li in LiFePO4 by capacity intermittent titration technique (CITT)

Capacity intermittent titration technique (CITT) was used to investigate the chemical diffusion coefficient () of lithium-ion in LiFePO₄ cathode material. The values of at the galvano-charge current of 0.2 and 0.4 mA were respectively found to range from 8.8 × 10⁻¹⁶ to 8.9 × 10⁻¹⁴ cm² s⁻¹ and from 1.2 × 10⁻¹⁶ to 8.5 × 10⁻¹⁴ cm² s⁻¹ in the voltage range from 3.2 to 4 V (vs. Li⁺/Li). The transfer coefficients of cathode (0.32-0.42) and anodic (0.26-0.3), and the standard rate constant (1.58 × 10⁻⁹ to 1.30 × 10⁻⁸ cm s⁻¹) were measured from the Tafel plots of LiFePO₄ in the equilibrium potential range from 3.06 to 3.45 V. From these kinetic parameters, the finite kinetics at interface was taken into account to revise the above values of . The revised values of at the galvano-charge current of 0.2 and 0.4 mA were respectively found to range from 2.44 × 10⁻¹⁵ to 2.21 × 10⁻¹³ cm² s⁻¹ and from 5.81 × 10⁻¹⁶ to 3.22 × 10⁻¹³ cm² s⁻¹ in the voltage range from 3.2 to 4 V. Results show that the approximation of infinite charge-transfer kinetics leads to a spurious value of which is lower than the revised value, and the spurious extent depends on the galvano-charge current of CITT experiment.     

Factor affecting rate performance of undoped LiFePO4

Undoped lithium iron phosphate (LiFePO₄) was prepared and characterized by scanning electron microscope (SEM) and X-ray diffraction (XRD) analysis. The material has a single crystal globular structure with grain-sizes ca. 100-150 nm. It was used to prepare composite electrodes containing different amounts of carbon (10, 15 and 20 wt.%, respectively) used as cathodes in non-aqueous lithium cells. By increasing the carbon content, an increase in the overall electrochemical performance was observed. Impedance spectroscopy was used to investigate the ohmic and kinetic contributions to the cell overvoltage. It was found that increasing the carbon content leads to a reduction of the cell impedance as a consequence of the reduction of the charge transfer resistance. The poor performance exhibited at very high discharge rates is a direct consequence of the high value of the charge transfer resistance. A further decrease of the charge transfer resistance in high carbon content cathodes (20 wt.% carbon) was obtained by improving the powder mixing procedure. The cell performance of well mixed, high carbon content electrodes was better than our previously obtained results in terms of higher capacity retention both for different discharge rates and repeated cycling. For currents larger than a 3 C rate, a severe capacity fade affected the electrodes. It was concluded that the electronic contact at the LiFePO₄/carbon interface plays a decisive role in material utilization at different discharge rates which affects the capacity fade upon cycling.     

Effect of carbon coating on low temperature electrochemical performance of LiFePO4/C by using polystyrene sphere as carbon source

Carbon perfectly coated LiFePO₄ cathode materials are synthesized by carbon-thermal reduction method using polystyrene (PS) spheres as carbon source. The PS spheres with diameters of 150–300 nm used for the pyrolysis reaction not only inhibit the particle growth but also lead to uniform distribution of carbon coating on the surface of LiFePO₄ particles. Rate capability and cycling stability of LiFePO₄/C with the carbon contents ranging from 1.4 wt% to 3.7 wt% are investigated at −20 °C. The LiFePO₄/C with 3.0 wt% C exhibits excellent electrochemical capability at low temperature, which delivers 147 mAh g⁻¹ at 0.1 C. After 100 cycles at a charge–discharge rate of 1 C, there is still 100% of initial capacity retained for the LiFePO₄/C electrode at −20 °C. According to the transmission electron microscope analysis and cyclic voltammetry measurement, this can be attributed to the good carbon coating morphology and optimal carbon coating thickness.     

Preparation and electrochemical properties of a LiFePO4/C composite cathode material by a polymer-pyrolysis–reduction method

A LiFePO₄/C composite was successfully prepared by a polymer-pyrolysis–reduction method, using FePO₄·2H₂O and lithium polyacrylate (PAALi) as raw materials. The structure of the LiFePO₄/C composites was investigated by X-ray diffraction (XRD). The micromorphology of the precursor and LiFePO₄/C powders was observed using scanning electron microscopy (SEM), and the in situ coating of carbon on the particles was observed by transmission electron microscopy (TEM). Furthermore, the electrochemical properties were evaluated by cyclic voltammograms (CVs), electrochemical impedance spectra (EIS) and constant current charge/discharge cycling tests. The results showed that the sample synthesized at 700 °C had the best electrochemical performance, exhibiting initial discharge capacities of 157, 139 and 109 mAh g⁻¹ at rates of 0.1, 1 and 5 C, respectively. Moreover, the sample presented excellent capacity retention as there was no significant capacity fade after 50 cycles.     

Rheological phase reaction synthesis and electrochemical performance of Li3V2(PO4)3/carbon cathode for lithium ion batteries

Monoclinic lithium vanadium phosphate/carbon (Li₃V₂(PO₄)₃/C) cathode has been synthesized for applications in lithium ion batteries, via a rheological phase reaction (RPR) method. The sample is characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). This material exhibits high initial discharge capacity of 189 and 177 mAh g⁻¹ at 0.1 and 0.2 C between 3.0 and 4.8 V, respectively. Moreover, it displays good fast rate performance, which discharge capacities of 140, 133, 129 and 124 mAh g⁻¹ can be delivered after 100 cycles between 3.0 and 4.8 V vs. Li at a different rate of 0.5, 1, 2 and 5 C, respectively. The electrochemical impedance spectroscopy (EIS) is also investigated.     

Improved electrochemical performance of La0.7Sr0.3MnO3 and carbon co-coated LiFePO4 synthesized by freeze-drying process

Carbon coated LiFePO₄ particles were first synthesized by sol-gel and freeze-drying method. These particles were then coated with La_0.7Sr_0.3MnO₃ nanolayer by a suspension mixing process. The La_0.7Sr_0.3MnO₃ and carbon co-coated LiFePO₄ particles were calcined at 400 °C for 2 h in a reducing atmosphere (5% of hydrogen in nitrogen). Nanolayer structured La_0.7Sr_0.3MnO₃ together with the amorphous carbon layer forms an integrate network arranged on the bare surface of LiFePO₄ as corroborated by high-resolution transmission electron microscopy. X-ray diffraction results proved that the co-coated composite still retained the structure of the LiFePO₄ substrate. The twin coatings can remarkably improve the electrochemical performance at high charge/discharge rates. This improvement may be attributed to the lower charge transfer resistance and higher electronic conductivity resulted from the twin nanolayer coatings compared with the carbon coated LiFePO₄.     

Optimized electrochemical performance of LiMn0.9Fe0.1−xMgxPO4/C for lithium ion batteries

A series of LiMn_0.9Fe_0.1−xMg_xPO₄/C (x = 0, 0.01, 0.02, 0.05) was synthesized by a solid state reaction, and the effect of synthesis temperature and Fe/Mg ratio on the electrochemical performance of the obtained materials was investigated by X-ray diffraction, scanning electron microscopy, Raman spectroscopy and electrochemical measurements. The electrochemical performance of the Fe and Mg co-substituted LiMnPO₄ was obviously improved with increasing synthesis temperature from 650 to 800 °C, but further increase led to an abrupt capacity loss due to the impurity formation. The Fe and Mg co-substitution could remarkably enhance the electrochemical activity of LiMnPO₄ compared with the Fe substitution only, but too high level of Mg doping would worsen the rate capability. The LiMn_0.9Fe_0.09Mg_0.01PO₄/C synthesized at 800 °C demonstrated the optimum electrochemical performance with a high capacity and an excellent rate capability. Even discharged at the rate of 10 C, a capacity of 60 mAh g⁻¹ was still observed.     

Effect of Sn doping on the electrochemical performance of NaTi2(PO4)3/C composite

In this paper, NaTi_2-xSn_x(PO₄)₃/C (x?=?0.0, 0.2, 0.3, and 0.4) composites were fabricated via facile sol-gel method, and employed as anodes for aqueous lithium ion batteries. Effect of Sn doping with various content on electrochemical properties of NaTi₂(PO₄)₃/C was investigated systematically. Sn doping on Ti site has no obvious effect on the lattice structure and morphology of NaTi₂(PO₄)₃/C. Among all samples, NaTi_1.7Sn_0.3(PO₄)₃/C (NC-Sn-3) demonstrates the best electrochemical properties. NC-Sn-3 exhibits the outstanding rate performance, delivering a discharge capacity of 103.3, 95.2, and 87.4?mAh?g^?1 at 0.5, 7, and 20?°C, respectively, 1.7, 30.5, and 56.2?mAh?g^?1 larger than those of pristine NaTi₂(PO₄)₃/C. In addition, NC-Sn-3 shows excellent cycling performance with the capacity retention of 80.6% after 1000 cycles at 5?°C. This work reveals that Sn doped NaTi₂(PO₄)₃/C with outstanding electrochemical properties are potential anode for aqueous lithium ion batteries.     

Effect of the stirring rate on physical and electrochemical properties of LiMnPO4 nanoplates prepared in a polyol process

In a polyol approach to make olivine-typed LiMnPO₄ nanoplates, the effect of the stirring rate on physical and electrochemical properties of the obtained sample has been symmetrically investigated for the first time. The as-prepared powders exhibit well crystalline olivine structure as presented by X-ray diffraction analysis. The secondary particles with a size of 2–3 μm are composed of aggregated nanoplates as verified by particle size analysis and field emission scanning electron microscopy measurement. Transmission electron microscopy presents that the nanoplate is about 18 nm thick along a-axis. The discharge capacity of the sample prepared under a stirring rate of 700 rpm reaches 150 mAh g⁻¹ when cycled at 0.05C after a few cycles.     

Electrochemical properties of carbon-coated LiFePO4 cathode using graphite, carbon black, and acetylene black

Electrochemical properties of LiFePO₄ were investigated by incorporating conductive carbon from three different carbon sources (graphite, carbon black, acetylene black). SEM observations revealed that the carbon-coated LiFePO₄ were smaller than the bare LiFePO₄ particles. The carbon-coated LiFePO₄ showed much better performance in terms of the discharge capacity and cycling stability than the bare LiFePO₄. Among carbon-coated LiFePO₄, the particles coated with graphite exhibited better electrochemical properties than others coated with carbon black or acetylene black.