Sensorless torque control of SyncRel motor drives

This paper describes a direct self-control (DSC) scheme for synchronous reluctance motor drives. The presented DSC scheme develops a new torque control methodology that does not require any position transducer to synchronize the stator current vector with the rotor. Such a control strategy differs from the conventional DSC approach in order to fit some specific requirements of synchronous reluctance (SyncRel) machines. First, torque and rotor position are controlled instead of torque and stator flux as in a conventional DSC scheme. Second, the operating sector is selected according to the actual position of the current vector rather than the position of the stator flux. The proposed methodology allows simplifying implementation of the torque control on SyncRel drives and reducing the global cost for medium-performance electric drives. Simulations and experimental tests on a 1.5-kW motor drive are provided to evaluate the consistency and the performance of the proposed control technique     

A new stator resistance tuning method for stator-flux-orientedvector-controlled induction motor drive

Field-oriented-controlled induction motor drives have been widely used over the last several years. Conventional direct stator-flux-oriented control schemes have the disadvantage of poor performance in the low-speed operating area when the stator flux is calculated using the voltage model, due to the stator resistance uncertainties and variations. In this paper, a new closed-loop stator-flux estimation method for a stator-flux-oriented vector-controlled induction motor drive is presented in which the stator resistance value is updated during operation. This method is based on a simple algorithm capable of running in a low-cost microcontroller, which is derived from the dynamic model of the induction machine. The effects of stator resistance detuning, especially in the low-speed operating region, are investigated and simulation results are shown. The motor drive system as well as the control logic and the resistance estimator are simulated and characteristic simulation results are derived. In addition, the proposed control scheme is experimentally implemented and some characteristic experimental results are shown. The simulation as well as the experimental results reveal that the proposed method is able to obtain precise flux and torque control, even for very low operating frequencies     

基于电阻压降补偿的直接转矩控制的研究

本文分析了异步电动机直接转矩控制的基本原理,完成基于空间电压矢量控制技术(SVPWM)的异步电机直接转距控制的MATLAB/SIMULINK仿真研究,并对低速时异步电动机性能进行了简单分析,采用定子电阻压降补偿来减小磁链轨迹的畸变,得到了较好的控制效果。     

Direct self-control (DSC) of inverter-fed induction machine

The new direct self-control (DSC) is a simple method of signal processing that gives converter-fed three-phase machines an excellent dynamic performance. To control the torque of, say, an induction motor, it is sufficient to process the measured signals of the stator currents and the total flux linkages only. In the basic version of DSC, the power semiconductors of a three-phase voltage source inverter are directly switched on and off via three Schmitt triggers, comparing the time integrals of line-to-line voltages to a reference value of desired flux, if the torque has not yet reached an upper-limit value of a two-limit torque control. Optimal performance of drive systems is accomplished in steady state as well as under transient conditions by combination of several two-limit controls     

Online Stator and Rotor Resistance Estimation Scheme Using Artificial Neural Networks for Vector Controlled Speed Sensorless Induction Motor Drive

This paper presents a new method of online estimation for the stator and rotor resistances of the induction motor for speed sensorless indirect vector controlled drives, using artificial neural networks. The error between the rotor flux linkages based on a neural network model and a voltage model is back propagated to adjust the weights of the neural network model for the rotor resistance estimation. For the stator resistance estimation, the error between the measured stator current and the estimated stator current using neural network is back propagated to adjust the weights of the neural network. The rotor speed is synthesized from the induction motor state equations. The performance of the stator and rotor resistance estimators and torque and flux responses of the drive, together with these estimators, are investigated with the help of simulations for variations in the stator and rotor resistances from their nominal values. Both resistances are estimated experimentally, using the proposed neural network in a vector controlled induction motor drive. Data on tracking performances of these estimators are presented. With this speed sensorless approach, the rotor resistance estimation was made insensitive to the stator resistance variations both in simulation and experiment. The accuracy of the estimated speed achieved experimentally, without the speed sensor clearly demonstrates the reliable and high-performance operation of the drive     

A new scheme for speed-sensorless control of induction motor

Various control algorithms have been proposed for the speed-sensorless control of an induction motor. These sensorless algorithms are mainly based on the speed feedback with the flux and speed estimations. This paper proposes a new scheme for the speed-sensorless control of an induction motor. The proposed scheme is based on the current estimation without the flux and speed estimations, in which the controlled stator voltage is applied to the induction motor so that the difference between stator currents of the mathematical model and motor may be forced to decay to zero. The performance of the proposed scheme is verified through simulation and experiment.     

Independent field-oriented control of two split-phase induction motors from a single six-phase inverter

Split-phase (six-phase) induction motor stator windings consist of two sets of three phase windings, which are spatially phase separated by 30 electrical degrees. Due to mutual cancellation of the air gap flux for all the 6n/spl plusmn/1 (n=1,3,5...) order harmonic voltages, called zero sequence components, large harmonic currents are generated in the stator phases. Only the 12n/spl plusmn/1 (n=0,1,2,3...)-order harmonic voltage components contribute toward the air gap flux and electromagnetic torque production in the machine. In this paper, a novel scheme is proposed where two six-phase induction motors are connected in series with proper phase sequence so that the zero sequence component voltages of one machine act as torque and flux producing components for the other. Thus, the two six-phase motors can be independently controlled from a single six-phase inverter. A vector control scheme for the dual motor drive is developed and experimentally verified in this paper.     

Stator resistance tuning in a stator-flux field-oriented driveusing an instantaneous hybrid flux estimator

A self-tuning control scheme for stator-flux field-oriented induction machine drives in electric vehicles operating over a wide speed range is discussed in this paper. The stator flux can be determined accurately from the terminal voltage when the machine is operating at high speed. However, at low speed, the stator resistance must be known to calculate the stator flux. The problem of calculating the stator flux accurately over the entire speed range is addressed. The rotor flux can be found from the machine speed and rotor time constant. The stator flux, at low speed, is then calculated directly from the rotor flux. By alternating between these two methods of determining the stator flux, a self-tuning operation is achieved, wherein the stator and rotor resistances are periodically updated. Since both methods of determining the stator flux are forced to track one another, a smooth transition between flux estimators is obtained. The torque and flux are then controlled in a deadbeat fashion. Good torque control over a wide speed range can therefore be obtained. With the proposed scheme, the advantages of direct torque control are obtained over the entire speed range with the addition of a speed sensor     

基于SVPWM的永磁同步电动机直接转矩控制

针对永磁同步电动机直接转矩控制系统转矩和定子磁链脉动问题,采用电压空间矢量脉宽调制(SVPWM)的永磁同步电动机直接转矩控制方法。根据在每一个控制周期内,计算出参考磁链和所估计磁链的偏差,选择相邻非零矢量和零矢量,并精确地计算出各自的作用时间,然后利用线性组合法将其合成为新的电压矢量。仿真结果表明,所提出的控制方案是有效的,明显地改善转矩和磁链脉动,并且有很好的动态和稳态性能。     

Direct self control with minimum torque ripple and high dynamics for a double three-level GTO inverter drive

A highly dynamic control scheme with very low torque ripple-direct self control (DSC) with torque hysteresis control-for very high-power medium-voltage induction motor drives fed by a double three-level inverter (D3LI) is presented. In this arrangement, two three-level inverters that are connected in parallel at their DC sides are feeding the open motor windings. The DSC, well known from two- and three-level inverters, is adapted to the D3LI and optimized for a minimum torque ripple. An 18-corner trajectory is chosen for the stator flux of the induction machine since it is approaching the ideal circle much better than the hexagon known from DSC for two-level inverters, without any detriment to the torque ripple. The machine and inverter control are explained and the proposed torque quality and dynamics are verified by measurements on a 180-kW laboratory drive.     

Flux observer with online tuning of stator and rotor resistancesfor induction motors

This paper proposes an adaptive flux observer for induction motors, where stator and rotor resistances are estimated in online environments. The variation of motor parameters during operation degrades the performance of the controller and the flux observer. Among the parameters of induction motors, rotor resistance is a crucial one for flux estimation, and stator resistance also becomes critical in the low-speed region. Under the persistent excitation condition, the proposed method estimates the actual values of stator and rotor resistances simultaneously, which guarantees the exact estimation of the rotor flux. The persistent excitation condition is not satisfied when the electric torque of an induction motor is absent due to the lack of rotor currents. Even in this case, the proposed method achieves the correct estimation of the rotor flux. Simulations and actual experiments show that the rotor flux is estimated in all operating conditions and that both resistances converge to their actual values when the electrical motor torque exists     

Analysis of direct torque control in permanent magnet synchronousmotor drives

This paper describes an investigation of direct torque control (DTC) for permanent magnet synchronous motor (PMSM) drives. It is mathematically proven that the increase of electromagnetic torque in a permanent magnet motor is proportional to the increase of the angle between the stator and rotor flux linkages, and, therefore, the fast torque response can be obtained by adjusting the rotating speed of the stator flux linkage as fast as possible. It is also shown that the zero voltage vectors should not be used, and stator flux linkage should be kept moving with respect to the rotor flux linkage all the time. The implementation of DTC in the permanent magnet motor is discussed, and it is found that for DTC using available digital signal processors (DSPs), it is advantageous to have a motor with a high ratio of the rated stator flux linkage to stator voltage. The simulation results verify the proposed control and also show that the torque response under DTC is much faster than the one under current control     

Speed-sensorless sliding-mode torque control of an induction motor

Novel induction motor control optimizing both torque response and efficiency is proposed in the paper. The main contribution of the paper is a new structure of rotor flux observer aimed at the speed-sensorless operation of an induction machine servo drive at both low and high speed, where rapid speed changes can occur. The control differs from the conventional field-oriented control. Stator and rotor flux in stator fixed coordinates are controlled instead of the stator current components in rotor field coordinates i_sd and i_sq. In principle, the proposed method is based on driving the stator flux toward the reference stator flux vector defined by the input command, which are the reference torque and the reference rotor flux. The magnitude and orientation angle of the rotor flux of the induction motor are determined by the output of the closed-loop rotor flux observer based on sliding-mode control and Lyapunov theory. Simulations and experimental tests are provided to evaluate the consistency and performance of the proposed control technique     

A Loss-Minimization DTC Scheme for EV Induction Motors

This paper proposes a strategy to minimize the losses of an induction motor propelling an electric vehicle (EV). The proposed control strategy, which is based on a direct flux and torque control scheme, utilizes the stator flux as a control variable, and the flux level is selected in accordance with the torque demand of the EV to achieve the efficiency-optimized drive performance. Moreover, among EV's motor electric propulsion features, the energy efficiency is a basic characteristic that is influenced by vehicle dynamics and system architecture. For this reason, the EV dynamics are taken into account. Simulation tests have been carried out on a 1.1-kW EV induction motor drive to evaluate the consistency and the performance of the proposed control approach     

Five-phase induction motor drives with DSP-based control system

This paper introduces two kinds of control schemes: vector control and direct torque control (DTC). These control schemes can be extensively applied to the operation of a five-phase induction motor using a fully digital implementation. Vector control of the five-phase induction motor not only achieves high drive performance, but also generates the desired nearly rectangular current waveforms and flux profile in the air-gap resulting in an improvement in air gap flux density and an increase of 10% in output torque. The DTC method has additional advantages when applied to multiphase, in this case a five-phase, induction motor. The five-phase inverter provides 32 space voltage vectors in comparison to 8 space voltage vectors provided by the three-phase inverter. Therefore, a more elaborate flux and torque control algorithm for the five-phase induction motor can be employed. Direct torque control of the five-phase induction motor reduces the amplitude of the ripples of both the stator flux and the torque, resulting in a more precise flux and torque control. A 32-b floating-point TMS320C32 digital signal processor (DSP) enables these two sophisticated control techniques to be conveniently implemented with high control precision. Experimental results show that an ideal control capability is obtained for both control methods when applied to the five-phase induction motor and further validates theoretical analysis     

Control of induction motors for both high dynamic performance andhigh power efficiency

The authors attempt to control induction motors with maximum power efficiency as well as high dynamic performance by means of decoupling of motor speed (or motor torque) and rotor flux. For maximum power efficiency, the squared rotor flux is adjusted according to a minimum power search algorithm until the measured power input reaches the minimum. Since the motor speed is dynamically decoupled from the rotor flux, this can be done successfully without any degradation of motor speed responses. The controller depends on rotor resistance but not on stator resistance. However, the performance of the control scheme is robust with respect to variations in rotor resistance because an identification algorithm for rotor resistance is employed. The identification algorithm for rotor resistance has some advantages over the previous methods. To demonstrate the practical significance of the results, some experimental results are presented     

Hybrid Cascaded H-Bridge Multilevel-Inverter Induction-Motor-Drive Direct Torque Control for Automotive Applications

This paper presents a hybrid cascaded H-bridge multilevel motor drive direct torque control (DTC) scheme for electric vehicles (EVs) or hybrid EVs. The control method is based on DTC operating principles. The stator voltage vector reference is computed from the stator flux and torque errors imposed by the flux and torque controllers. This voltage reference is then generated using a hybrid cascaded H-bridge multilevel inverter, where each phase of the inverter can be implemented using a dc source, which would be available from fuel cells, batteries, or ultracapacitors. This inverter provides nearly sinusoidal voltages with very low distortion, even without filtering, using fewer switching devices. In addition, the multilevel inverter can generate a high and fixed switching frequency output voltage with fewer switching losses, since only the small power cells of the inverter operate at a high switching rate. Therefore, a high performance and also efficient torque and flux controllers are obtained, enabling a DTC solution for multilevel-inverter-powered motor drives.      

Sensorless DTC-SVM for Induction Motor Driven by a Matrix Converter Using a Parameter Estimation Strategy

This paper presents a new direct torque controlled space vector modulated method to improve the sensorless performance of matrix converter drives using a parameter estimation scheme. The flux and torque error are geometrically combined in a new flux leakage vector to make a stator command voltage vector in a deadbeat manner. A new sensorless method of estimating the rotor speed, flux, stator resistance, and rotor resistance is derived and verified with experimental results. Common terms in the error dynamics are utilized to find a simpler error model involving some auxiliary variables. Using this error model, the state estimation problem is converted into a parameter estimation problem assuming the rotor speed is constant. The proposed adaptive schemes are determined so that the whole system is stable in the sense of Lyapunov. The effectiveness of the proposed algorithm is verified by experiments.     

A Direct-Flux-Vector-Controlled Induction Generator With Space-Vector Modulation for Integrated Starter Alternator

A direct-flux-vector-controlled scheme of induction generator has been proposed in this paper for future 42-V automobile application. The fundamental relationship between the rotating speed of the stator flux vector and torque is analyzed. A simple structure with only one proportional-integral (PI) controller is shown to implement the torque and flux controls adequately. By controlling the electromagnetic torque of the induction machine, the required dc-bus voltage can be well regulated within the 42-V PowerNet specifications. Fixed switching frequency and low torque ripple are obtained with space-vector modulation technique. Simulation and experimental results indicate that the proposed scheme provides a practical solution for an integrated starter alternator other than the widely applied field-oriented- control scheme.     

Performance of induction motor with free-rotating magnets insideits rotor

This paper presents a new induction motor that has free-rotating magnets inside a rotor. The magnets can revolve freely against the rotor with the shaft. In this motor, the airgap flux is provided by both rotating permanent magnets and the stator coil current. A prototype motor was fabricated by modifying the rotor of a conventional three-phase four-pole 400 W squirrel-cage induction motor. The experimental results of a prototype motor showed superior performance in comparison to conventional motors in terms of the power factor, efficiency and torque characteristics. The power factor can be controlled to be unity, leading or lagging by changing the supply frequency and/or source voltage. The efficiency of the motor, over a wide output power range, is remarkably higher than that of the same size conventional induction motor. A high torque can be obtained in a high speed area